Friedrich CP24F30 User Manual

Size:
3.9 Mb
Download

CP15F10A

/

Table of Contents

 

Air Conditioner Safety

1

Installation Requirements

3

Tools and Parts ....................................................................................................................................................................

3

Location Requirements

3

Electrical Requirements

4

Installation Instructions ..................................................................................................................................................

6

Unpacking

6

Window Installation (on some models)

7

Through-the-WallCabinet Installation ...............................................................................................................................

9

Complete Installation

10

Air Conditioner Use

11

Starting Your Air Conditioner—DigitalControl ..............................................................................................................

12

Remote Control Operation

13

Normal Sounds

13

Air Conditioner Care........................................................................................................................................................

14

Cleaning the Air Filter

14

Cleaning the Front Panel

14

Repairing Paint Damage ...................................................................................................................................................

14

Annual Maintenance

14

Troubleshooting

14

Assistance or Service ......................................................................................................................................................

15

Warranty

16

1

General Instructions

This Installation and Operation Manual has been designed to insure maximum satisfaction in the performance of your unit. For years of trouble-freeservice, please follow the installation instructions closely. We cannot overemphasize the importance of proper installation. We have added new information to the basic instructions to help you achieve success.

WARNING

Refrigeration system under high pressure.

Do not puncture, heat, expose to flame or incinerate.

Only certified refrigeration technicians should service this equipment.

R410A systems operate at higher pressures than R22 equipment. Appropriate safe service and handling practices must be used.

Only use gauge sets designed for use with R410A. Do not use standard R22 gauge sets.

WARNING

Please read this manual thoroughly prior to equipment installation or operation.

It is the installer’s responsibility to properly apply and install the equipment. Installation must be in conformance with the NFPA 70-2008National Electric Code or current edition, International Mechanic Code 2009 or current edition and any other applicable local or national codes.

Failure to do so can result in property damage, personal injury and / or death.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is a safety Alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol with the word “WARNING” or “CAUTION”. These words mean:

Indicates a hazard which, if not WARNING avoided, can result in severe personal injury or death and damage

to product or other property.

CAUTION Indicates a hazard which, if not avoided, can result in personal injury

and damage to product or other property.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what will happen if the instructions are not followed.

NOTICE

occur if

instructions are

not

 

Indicates

property damage

can

 

 

 

 

followed.

 

 

 

2

K

K.pan-headPhillipsscrews(2)

Window installation

Electrical Requirements

 

Window opening measurements:

27"min. to 42" max. (76.2 cm to 101.6 cm) opening width (A).

20" min. (50.8 cm) opening height (B).

 

A

 

 

B

A .27"

min. (76

. 2 c m)

B . 20" min. (50

. 8 c m)

Through-the-wallinstallation

The wall opening measurements should be:

Height (A): 17 ¼" plus twice thickness of wood used to build frame

Width (B): 26 ¼"

Depth (D): 4" minimum to 8" maximum.

C

A

B

D

 

C

A. 17 ¼"

C. Wood thickness

B. 26 ¼"

D. 4" minimum to

 

8" maximum.

Ground wire must be connected to ground screw located in lower right corner of air conditioner when air conditioner is in cabinet.

The electrical ratings for your air conditioner are listed on the model and serial number (nameplate) label. The model and serial number label is located behind the front panel on the flange below the control panel area.

Specific electrical requirements are listed in the chart below. Follow the requirements for the type of plug on the power supply cord.

Power supply

 

 

cord

Wiring requirements

 

 

CP15

115-volt(103.5 min. - 126.5 max.)

 

0-12amps

 

15-amptime-delayfuse or circuit breaker

 

Use on single outlet circuit only.

 

 

CP18 / CP24

230-volt(207 min. - 253 max.)

¹⁄"

 

0-12amps

(0.6 cm)

15-amptime-delayfuse or circuit breaker

Use on single outlet circuit only.

4

Recommended grounding method

This air conditioner must be grounded. This air conditioner is equipped with a power supply cord having a grounded 3 prong plug. To minimize possible shock hazard, the cord must be plugged into a mating, grounded 3 prong outlet, grounded in accordance with all local cod es and ordinances. If a mating outlet is not available, it is the customer' s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrical component installer.

It is the customer' s responsibility:

To contact a qualified electrical installer, and

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 - latest edition, and all local cod es and ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

Power Supply Cord

NOTE: Your unit’s device may differ from the ones shown.

B A

TEST

RESET

TEST

RESET

BA

A.Reset button

B.Test button

This room air conditioner is equipped with a power supply cord required by UL. This power supply cord contains state-of-the-artelectronics that sense leakage current. If the cord is crushed, the electronics detect leakage current and pow er will be disconnected in a fraction of a second.

To test your power supply cord:

1.Plug power supply cord into a grounded 3 prong outlet.

2.Press RESET.

3.Press TEST (listen for click; Reset button will trip and pop out).

4.Press and release RESET (listen for click; Reset button will latch and remain in). The power supply cord is ready for operation.

NOTES:

The Reset button must be pushed in for proper operation.

The power supply cord must be replaced if it fails to trip when the test button is pressed or if it fails to reset.

Do not use the power supply cord as an off/on switch. The power supply cord is designed as a protective device.

A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired.

The power supply cord contains no user serviceable parts. Opening the tamper-resistantcase voids all warranty and performance claims.

5

Window Installation (on some models)

NOTES:

Handle air conditioner carefully and gently.

Be sure your air conditioner cabinet does not fall out of the opening during installation or removal.

The place where the power cord exits the air conditioner should be no more than 4 ft (122 cm) from a grounded 3 prong power outlet.

Do not block the louvers on the front panel.

Do not block the louvers on the outside of the air conditioner.

Attach Top Channel

NOTE: Attach top channel and side curtains to air conditioner cabinet before placing cabinet in window.

1.Locate provided bag of screws.

2.Place top channel on top of air conditioner cabinet, lining up the 4 holes in top channel with the 4 holes on top of air conditioner cabinet.

3.Using 4 - #10 x ³⁄ " washer-headPhillipsthread-cuttingscrews, attach top channel to air conditioner cabinet.

A

B

A.Top channel

B.#10 x ³⁄" washer-headPhillipsthread-cuttingscrews

Attach Side Curtains

1.Locate provided bag of screws.

2.Insert top and then bottom of right-handcurtain housing in top and bottom curtain channels on air conditioner.

Top view

A B

Bottom view

A

B

A.Curtain housing

B.Curtain bottom channel on air conditioner

3.Extend right-handcurtain outward so you may insert the first screw through the middle hole of the curtain. Using #10 x ¹⁄ "pan-headPhillips screw, screw curtain to middle hole in air conditioner cabinet.

NOTE: This screw is required to correctly attach curtain (top to bottom) to the air conditioner cabinet.

4.While the right-handcurtain is still extended, insert #10 x ¹⁄ "pan-headPhillips screws into the top and bottom slots of curtain. Screw curtain to the top and bottom holes in the air conditioner cabinet side.

5.Slide the curtain housing into the curtain channels as far as it will go.

6.Repeat above steps for the left-handcurtain.

Attach foam adhesive seal

Attach foam adhesive seal along the bottom of the curtain bottom channel.

A

B

A.Curtain housing

B.Foam adhesive seal

A. Curtain housing

7

B. Curtain top channel on air conditioner

 

7

12

Use 2" x 4" or thicker lumber for wood frame.

A

B

C

A.Outside width

B.Outside height

C.Depth

4.Apply wood preservative to the outside exposed surface.

5.Insert the frame in the wall opening. Square and level frame.

6.Attach frame securely to the wall.

Install Cabinet into Wood Frame

1.Remove top channel and both side channels using a ¹⁄" nut driver or socket wrench. Discard top channel and both side channels.

2. Cut two pieces of standard 1" lumber (supplied by installer) to the length and width required. Place in front and back of bottom sill channel. Secure with nails (supplied by installer).

¾" Minimum

Cabinet front

1" Thick lumbeer

1" Minimum

Inside wall

Exterior wall

Front edge of louvers must always be outside of exterior wall surface

¼" Slope down.

Position and secure cabinet downward. Slope outside for drainage.

Max. Wall thickness allowed 8 ½"

3. Insert cabinet into the framed wall opening. the top of the cbine should extend ¾" (19.1 mm) into the room. If there is trim, the cabinet should extend ¾" (19.1 mm) past the trim.

B

A

A.³⁄ " (19.1 mm) extending into room

B.Trim

4.Use a level to check that cabinet is level side to side.

A

A. Level

5. Check that air conditioner cabinet is tilted to the outside so that water will run to the outside.

6. Reuse the insulation to seal opening between cabinet and frame.

7.Use existing holes in sides and top of cabinet and 7 - #10 x 1" wood screws (not provided) to attach cabinet to frame.

NOTE: Do not overtighten screws or cabinet will distort and provide a poor air seal between cabinet and air conditioner.

8. Caulk all outside wall openings around cabinet.

Complete Installation

NOTE: Handle air conditioner carefully and gently.

1.Make sure the free end of the ground wire is outside of the cabinet.

2. Insert air conditioner into cabinet.

to move and install

A

A

10A. Make sure the free end of the ground wire is outside of the cabinet.

and2-#9.5X

3/8”pan-headPhillips screws, attach front of panel to chassis.

Starting Your Air Conditioner—DigitalControl

Money

Auto Swing

 

Timer

Saver®

 

 

 

 

 

 

0F

 

 

 

 

Temp/Hour

POWER

 

Hr.

 

 

 

 

Cool

 

High

 

 

Mode

Med

Fan Speed

Fan Only

 

Low

 

Temperature

Press, or press and hold, the plus button to raise the temperature 1º until it reaches 90ºF (32.2ºC).

0F

Temp/Hour

Hr.

Press, or press and hold, the minus button to lower the temperature 1º until it reaches 60ºF (15.5ºC).

1. Press POWER to turn on air conditioner.

POWER

NOTE: When the unit is turned on, it will display the previous settings for the Mode, Fan Speed and temperature.

Timer Delay

To set the Timer for a 1- to 24-hourdelay until the air conditioner turns off (the air conditioner must be On):

1. Press TIMER. Indicator light will flash.

Timer

2.Choose mode. See “Mode.”

3.Choose fan speed. See “Fan Speed.”

4.Choose temperature. See “Temperature.”

Mode

1.Press and hold MODE.

2.Choose Cool or Fan mode

Cool—Coolsroom. Press FAN SPEED to choose fan speed. Then adjust the temperature by pressing the up or down arrow buttons.

Fan—Operatesthe fan at High speed, without cool ing. The display shows “FO” (fan only).

Money Saver®

Money Saver — Cycles fan with compressor when room temperature reaches the temperature setting on the thermostat.

Cool

Money

Mode

Fan Only

Saver®

 

Fan Speed

NOTE: The Fan Speed button will operate when the Cool, Money Saver or Fan Only mode has been selected.

1.Press the Fan Speed button until you see the indicator light for the desired setting.

2.Choose Low, Medium or High.

High

Med

Fan Speed

Low

2.Press the plus or minus button to change the delay time from 1 to 24 hours.

3.Press TIMER or wait 10 seconds. Indicator light will remain on.

To set the Timer delay for a 1- to 24-hourdelay until the air conditioner turns on, keeping previous settings:

1.Turn off air conditioner.

2.Press TIMER. Indicator light will flash.

3.Press the plus or minus button to change the delay time from 1 to 24 hours.

4.Press TIMER or wait 10 seconds. Indicator light will remain on.

To set the Timer delay for a 1- to 24-hourdelay until the air conditioner turns on, changing previous settings:

1.Turn on air conditioner.

2.Adjust MODE to desired setting.

3.Adjust FAN SPEED to Low, Medium or High.

4.Adjust temperature between 60ºF (15.5ºC) and 90ºF (32.2ºC).

5.Turn off air conditioner.

6.Press TIMER. Indicator light will flash.

7.Press the plus or minus button to change delay time from 1 to 24 hours.

8.Press TIMER or wait 10 seconds.

To clear Timer delay program

NOTE: Air conditioner can be either on or off.

Press TIMER. Indicator light will turn off.

12

To operate air conditioner with remote control

NOTE: Remote control may vary in appearance.

NOTE: Two AAA batteries (included) power the remote control. Replace batteries after 6 months of use, or when the remote control starts to lose power.

To turn the air conditioner on or off:

Press POWER.

To select the mode:

Press COOL, FAN or $ SAVER

To select the fan speed:

Press FAN SPEED for Low, Medium or High.

To raise the temperature:

Press the plus button to raise the temperature. Each time you press or hold the plus button, the temperature will go up 1º until it reaches 90°F (32.2°C).

To lower the temperature:

Press the minus button to lower the temperature. Each time you press or hold the minus button, the temperature will go down 1º until it reaches 60°F (15.5°C).

To set Timer for a 1- to 24-hourdelay before air conditioner is turned off (air conditioner must be On):

1.Press TIMER. Indicator light on air conditioner control panel will flash.

2.Press the plus or minus button to change the delay time from 1 to 24 hours.

3.Press TIMER again or wait 10 seconds. Indicator light on air conditioner control panel will remain on.

To set Timer to turn on air conditioner, keeping previous settings:

1.Turn off air conditioner.

2.Press TIMER. Indicator light on air conditioner control panel will flash.

3.Press the plus or minus button to change delay time (1 to 24 hours).

4.Press TIMER again or wait 10 seconds. Indicator light on air conditioner control panel will remain on.

To set Timer to turn on air conditioner, changing the previous settings:

1.Turn on air conditioner.

2.Adjust Mode to Cool, Fan Only, or Power Saver.

3.Adjust Fan Speed to High, Medium or Low.

4.Adjust temperature between 60°F (15.5ºC) and 90°F (32.2 ºC).

5.Turn off air conditioner.

6.Press TIMER. Indicator light on air conditioner control panel will flash.

7.Press the plus or minus button to change delay time (1 to 24 hours).

8.Press TIMER again or wait 10 seconds. Indicator light on air conditioner control panel will remain on.

13

Air Conditioner Care

Your new air conditioner is designed to give you many years of dependable service. This section tells you how to clean and care for your air conditioner properly. Call your local authorized dealer for an annual checkup. Remember… the cost of this service call is your responsibility.

Cleaning the Air Filter

The air filter is removable for easy cleaning. A clean filter helps remove dust, lint, and other particles from the air and is import ant for best cooling and op erating efficiency. Check the filter every 2 weeks to see whether it needs cleaning.

NOTE: Do not operate the air conditioner without the filter in place.

1.Turn off air conditioner.

2.Remove filter from unit.

3.Use a vacuum cleaner to clean air filter. If air filter is very dirty, wash it in warm water with a mild detergent. Do not wash air filter in the dishwasher or use any chemical cleaners. Air dry filter completely before replacing to ensure maximum efficiency.

4.Slide air filter down into t he filter door. Close filter door.

Cleaning the Front Panel

1.Turn off air conditioner.

2.Remove the air filter and clean it separately. See “Cleaning the Air Filter.”

3.Wipe the front panel with a soft, damp cloth.

4.Air dry front panel comp letely.

Repairing Paint Damage

Check once or twice a year for paint damage. This is very important, especially in areas near oceans or where rust is a problem. If needed, touch up with a good grade enamel paint.

Annual Maintenance

Your air conditioner needs annual maintenance to help ensure steady, top performance throughout the year. Call your local authorized dealer to schedule an annual checkup. The expense of an annual inspection is your responsibility.

Troubleshooting

Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.

Air conditioner will not operate

Air conditioner blows fuses or trips circuit breakers

.

The power supply cord is unplugged. Plug into a grounded 3 prong outlet. See “Electrical Requirements.”

The power supply cord has tripped (Reset button has popped out). Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.

A household fuse has blown, or a circuit breaker has tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. See “Electrical Requirements.”

Depending on model, the Power button has not been pressed or the Fan control is turned to Off. Press POWER or turn the Fan control to an active setting.

The local power has failed. Wait for power to be restored.

Too many appliances are being used on the same circuit.

Unplug or relocate appliances that share the same circuit.

Time-delayfuse or circuit breaker of the wrong capacityis b eing used. Replace with a time-d elay fuse or circuit breaker of the correct cap acity. See “Electrical Requirements.”

An extension cord is being used. Do not use an extension cord with this or any other appliance.

You are trying to restart the air conditioner too soon after turning the unit off. Wait at least 3 minutes after turning the unit off before trying to restart the air conditioner.

Normal Sounds

When your air conditioner is operating normally, you may hear sounds such as:

Droplets of water hitting the condenser, causing a pinging or clicking sound. The water droplets help cool the condenser.

Air movement from the fan.

Clicks from the thermostat cycle.

Vibrations or noise due to poor wall or window cons truction.

A high-pitched hum or pulsating noise caused by the modernhigh-efficiencycomp ressor cycling on and off.

14

Air conditioner power supply cord trips (Reset button pops out)

Disturbances in your electrical current can trip (Reset button will pop out) the power supply cord. Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.

Electrical overloading, overheating, cord pinching or aging can trip (Reset button will pop out) the power supply cord. After correcting the problem, press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.

NOTE: A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired.

Air conditioner seems to run too much

The current air conditioner replaced an older model. The use of more efficient components may cause the air conditioner to run longer than an older model, but the total energy consumption will be less. Newer air conditioners do not emit the “blast” of cold air you may be accustomed to from older units, but this is not an indication of lesser cooling capacity or efficiency. Refer to the efficiency rating (EER) and capacity rating (in BTU/hr.) marked on the air conditioner.

The air conditioner is in a heavily occupied room, or heatproducing appliances are in use in the room. Use exhaust vent fans while cooking or bathing and try not to use heatproducing appliances during the hottest part of the day. A higher capacity air conditioner may be required, depending on the size of the room being cooled.

Air conditioner cycles on and off too much, or does not cool/heat room in cooling/heating mode

The Mode or Fan control is set to Power Saver (on some models). Use Power Saver only when you are asleep or away from home, since the fan does not circulate the room air continuously. Use Low Cool, Medium Cool or High Cool for your best comfort.

The air conditioner is not properly sized for your room.

Check the cooling capabilities of your room air conditioner. Room air conditioners are not designed to cool multiple rooms.

The filter is dirty or obstructed by debris. Clean the filter.

The inside evaporator and outside condenser coils are dirty or obstructed by debris. See “Annual Maintenance.”

There is excessive heat or moisture (open container cooking, showers, etc.) in the room. Use a fan to exhaust heat or moisture from the room. Try not to use heatproducing appliances during the hottest part of the day.

The louvers are blocked. Install the air conditioner in a location where the louvers are free from curtains, blinds, furniture, etc.

The outside temperature is below 65°F (18°C). Do not try to operate your air conditioner in the cooling mode when the outside temperature is below 65°F (18°C).

The temperature of the room you are trying to cool is extremely hot. Allow extra time for the air conditioner to cool off a very hot room.

Windows or doors to the outside are open. Close all windows and doors.

The Vent control is set to OPEN (on some models). Push the Vent control to CLOSED for maximum cooling and/or heating.

The temperature set point or Thermostat control is not at a cool enough setting. Adjust the temperature set point to a cooler setting by pressing the minus button to reduce the temperature or adjust the Thermostat control to a cooler setting by turning the knob clockwise. Turn the Fan control to Turbo Cool.

The air contitioner in the heating mode has insufficient BTU/hr for the heating requirements of the room. Do not use the air conditioner as a primary source of heat.

Temperature on display does not match room temperature

When the compressor and fan motor turn off during Power Saver mode, or after you turn off the unit, a lower temperature reading than the actual room temperature may be displayed for a short period of time. This lower temperature reading is caused by the temperature sensor being located close to the cold evaporator coil. The actual room temperature will display within a few minutes.

Water drips from cabinet into your house

The air conditioner is not properly leveled. The air conditioner should slope slightly downward toward the outside. Level the air conditioner to provide a downward slope toward the outside to ensure proper drainage. See the Installation Instructions.

NOTE: Do not drill a hole into the bottom of the metal base and condensate pan.

Assistance or Service

For assistance, service or replacement parts

For service assistance or to locate factory-authorizedparts, call our Customer Service Center at1-800-541-6645,or your

nearest authorized service center. You also can visit the "Dealer Locator" at www.friedrich.com to locate your nearest authorized Friedrich Service Center.

For further assistance

If you need further assistance, you can write us at :

Friedrich Air Conditioning Co.

Customer Service

10001 Reunion Place, Suite 500

San Antonio, TX 78216

Or email: tac@friedrich.com

Please include a daytime phone number in your correspondence.

15

Friedrich Air Conditioning Company

10001 Reunion Place, Suite 500

78216 (800)541-6645www.friedrich.com

ROOM AIR CONDITIONERS

LIMITED WARRANTY

FIRST YEAR

ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of original purchase, FRIEDRICH will repair the product at no charge, provided room air conditioner is reasonably accessible for service. Any additional labor cost for removing inaccessible units and/or charges for mileage related to travel by a Service Agency that exceeds 25 miles one way will be the responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within twelve months from the date of the original purchase.

SECOND THROUGH FIFTH YEAR

SEALED REFRIGERANT SYSTEM: If the Sealed Refrigeration System (defined for this purpose as the compressor, condenser coil, evaporator coil, reversing valve, check valve, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in your Room Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase, FRIEDRICH will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System;PROVIDED FRIEDRICH will not pay the cost of diagnosis of the problem, removal, freight charges, and transportation of the air conditioner to and from the Service Agency, and the reinstallation charges associated with repair of the Sealed Refrigeration System. All such cost will be the sole responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase.

APPLICABILITY AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A., District of Columbia, and Canada. This warranty is not applicable to:

1.Air filters or fuses.

2.Products on which the model and serial numbers have been removed.

3.Products which have defects or damage which results from improper installation, wiring, electrical current characteristics, or maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication of the product and/or units installed in a corrosive atmosphere, default or delay in performance caused by war, government restrictions or restraints, strikes, material shortages beyond the control of FRIEDRICH, or acts of God.

OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service Organizationin your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty performance, write to: Room Air Conditioner Service Manager, Friedrich Air Conditioning Co., P.O. Box 1540, San Antonio, TX 78295-1540.

LIMITATIONS: THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty notwithstanding, ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.

Performance of Friedrich’s Warranty obligation is limited to one of the following methods:

1.Repair of the unit

2.A refund to the customer for the prorated value of the unit based upon the remaining warranty period of the unit.

3.Providing a replacement unit of equal value

The method of fulfillment of the warranty obligation is at the sole discretion of Friedrich Air Conditioning.

NOTE: Some states do not allow limitations on how long an implied warranty lasts, or do not allow the limitation or exclusion of consequential or incidental damages, so the foregoing exclusions and limitations may not apply to you.

OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

PROOF OF PURCHASE: Owner must provide proof of purchase in order to receive any warranty related services.

All service calls for explaining the operation of this product will be the sole responsibility of the consumer.

All warranty service must be provided by an Authorized FRIEDRICH Service Agency, unless authorized by FRIEDRICH prior to repairs being made.

(10-08)

1-800-541-6645

66129903813