Friedrich CP05 CP Line User Manual

Size:
2.29 Mb
Download

Room Air Conditioner

ENGLISH

 

Installation and Operation

 

Manual

FRANÇAIS

 

ESPAÑOL

CP Line

CP05

Registering Your Room Air Conditioner

Model information can be found on the name plate located on the side of the unit near the control panel. Please complete and mail the owner registration card furnished with this product or register on-lineat www.friedrich.com (USA only). For your future convenience, record the model information here.

 

 

 

 

 

 

 

 

 

 

 

 

MODEL NUMBER

SERIAL NUMBER

PURCHASE DATE

 

920-152-00(12/04)

Congratulations! Thank you for choosing

Friedrich.

Your Friedrich unit is designed for maximum comfort and quietness.

Table of Contents

 

Introduction ..................................................................................

3

Safety Precautions.......................................................................

4

How to operate your Friedrich ...................................................

6

Features and Installation.............................................................

8

Installation Instructions...............................................................

9

Troubleshooting Tips.................................................................

13

Warranty......................................................................................

14

Introduction

Before Operating Your Unit

Make sure the wiring is adequate for your unit.

If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in figure 1.

DO NOT use an extension cord.

The cord provided will carry the proper amount of electrical power to the unit; an extension cord will not.

Make sure that the receptacle is compatible with the wall plug provided.

This insures proper grounding. If you have a two-prongreceptacle you will need to have the circuit replaced by a certified electrician with a grounded circuit that meets all national and local codes and ordinances. You must use thethree-prongplug furnished with the air conditioner.

CIRCUIT

RATING OR

MODEL TIME DELAYPLUG FACE

FUSE

 

AMP

VOLT

NEMA NO.

 

 

 

 

 

 

 

 

 

Figure 1

CP05

15

125

5-15P

 

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

For the Best Cooling Performance and Energy Efficiency

Keep the filter clean

Make sure that your air conditioner is always in top performing condition by cleaning the filter regularly. Instructions for removing and cleaning the filter can be found on page 6.

Provide good airflow

Make sure that the airflow into and out of the unit is unobstructed. (both indoors and outdoors)

Maximum airflow is critical for peak performance. Your air conditioner blows air out of the top of the unit and takes in air at the bottom of the unit.

Unit Placement

If your air conditioner can be placed in a window or a wall that is shaded by a tree or another building, the unit will operate even more efficiently. Using drapes or blinds on the sunny side of the dwelling will also add to your unit's efficiency.

Insulation

Good insulation will be a big help in maintaining desirable comfort levels. Doors should have weather stripping. Be sure to caulk around doors and windows.

3

Safety Precautions

To prevent injury and property damage, follow these instructions.

Incorrect operation due to ignoring instructions can cause harm or damage. The seriousness is classified by the following indications.

WARNINGCAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

■ Meanings of symbols used in this manual are as shown below.

Never Do This

Always Do This

WARNING

Plug in the power plug properly.

Otherwise, it will cause electric shock or fire due to heat generation.

Do not modify power cord length.

It will cause electric shock or fire due to heat generation.

Do not operate or stop the unit by inserting or pulling out the power plug.

It will cause electric shock or fire due to heat generation.

Do not operate with wet hands or in damp environment.

• It will cause electric shock.

Do not damage or use an unspecified power cord.

It will cause electric shock or fire.

If the power cord is damaged, it must be replaced by the manufacturer or a Friedrich-certifiedservice agent.

Do not direct air flow directly at room occupants.

• This could lead to health problems.

4

Sharp edges

When the air filter is to be removed, do not touch the metal parts of the unit.

They are sharp and may cause an injury.

Do not clean the air conditioner with water.

Water may enter the unit and degrade the insulation. It may cause an electric shock.

When the unit is to be cleaned, switch the unit off, and unplug it.

Since the fan rotates at high speed during operation, it may cause an injury.

Do not operate the unit without the air filter or when the front intake grille has been removed.

It could cause dust to accumulate on the heat exchanger.

Do not apply an insecticide or flammable spray.

It may cause a fire or deformation of the cabinet.

Do not put a pet or house plant where it will be exposed to direct air flow.

This could injure the pets or plants.

SHARP EDGES!

The edges of the cabinet can be SHARP!

Use caution when handling the case. Grip it firmly and do not allow it to slip while holding it.

Use heavy gloves to handle

the cabinet if necessary.

• DO NOT

allow the cabinet to slide

against your skin!

Do not use for special purposes.

Do not use this air conditioner to preserve precision devices, food, pets, plants, and art objects. It may cause deterioration of quality, etc.

ENGLISH

5

How to operate your Friedrich

The controls will look like the following.

Control and Remote Control Operations

1 TEMPERATURE SETTING

These buttons control the temperature

of the room. The temperature can be set within a range of

60° F to 86° F, in increments of 1° F.

2 MONEY SAVER

1

2

3

4

6

Power

Temp

Fan Speed

Timer Mode

4

Money

Saver

2

5

5

1

6

3

The fan stops when the compressor stops cooling.

• Approximately every 3 minutes the fan will turn on and sample the room air to determine if more cooling is needed.

3OPERATION MODE SELECTOR

Everytime you push this button, it will rotate between the COOL, FAN and DRY modes.

4ON/OFF TIMER

ON-Ifunit is off, use Timer to set number of hours before unit starts.

Push Timer button to advance setting from 1hr - 2hrs - .....12hrs maximum.

OFF - You will usually useshut-offtime while you sleep.

If unit is running, use Timer to set number of hours until shut-off.

For your sleeping comfort, once Time is set, the temperature setting will rise 2° F after 30 min, and once again after another 30min.

Push Timer button to advance setting from 2 hrs....12 hrs maximum.

5POWER

To turn the unit ON, push the button. To turn the unit OFF, push the button again.

This button takes priority over all other buttons.

When you first turn it on, the unit is on the High Cool mode and the temperature is set at 72° F.

6FAN SPEED

Everytime you push this button it will rotate between the following fan speeds:

High (F3) Low(F1)Medium (F2)High (F3)

How to Insert Batteries

1.Remove the cover from the back of the remote control.

2.Insert two batteries.

Be sure that the (+) and (-)directions are correct.

Be sure that both batteries are new.

3.Re-attachthe cover.

Do not use rechargeable batteries. Such batteries differ from standard dry cells in shape, dimensions, and performance.

Remove the batteries from the remote control if the air conditioner is not going to be used for an extended length of time.

6

Additional controls and important information.

Air Direction

• ADJUSTING THE AIR DIRECTION USING THE HORIZONTAL AIR-DEFLECTORCONTROL

Using the control tabs, the air flow can be directed to the left, right, straight ahead, or any combination

of these directions.

Control Tabs

Care and Maintenance

TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.

• TO CLEAN FILTER

The air filter will become dirty as it removes

Filter

 

dust from the inside air.

 

It should be washed at least every 2 weeks.

Do not force open

If the air filter remains full of dust, the air

or open too far

flow will decrease and the cooling capacity

 

will be reduced, possibly damaging the unit.

 

1. Pull the inlet grille forward and pull out the

 

air filter. (Fig. 1)

 

2. Wash the air filter in warm water.

Inlet grill

Be sure to completely dry the filter before

Fig. 1

placing it back into the unit.

 

• CLEANING THE AIR CONDITIONER

The front grille and inlet grille may be wiped with a cloth dampened in a mild detergent and lukewarm water solution. (Fig. 2)

The cabinet may be washed with mild soap or Fig. 2 detergent and lukewarm water.

To ensure continued peak efficiency, the outdoor coil (condensor coil) should be checked periodically and cleaned if clogged with soot or dirt from the atmosphere.

Consult a certified Friedrich service agent for more information.

• HOW TO REMOVE THE FRONT GRILLE

Fig. 3

 

1. Pull the inlet grille forward.

2. Remove the screw securing the Front Grille. (Fig. 3)

3. Push the grille up from the bottom and pull the top of the grille away from the case to lift the top tabs out of their slots. (Fig. 4)

4. Carefully position the grille, bottom first, and snap back into Fig. 4 place.

5.Reposition the screw that secures the front grille and replace the knobs.

ENGLISH

7

Features and Installation

Learning the key components will help you properly install the unit.

Features

1

9

 

3

 

4

 

 

2

 

 

7

 

6

 

 

 

 

5

10

 

 

 

8

 

1. CABINET

 

6. AIR FILTER

2. HORIZONTAL AIR DEFLECTOR

7. CONTROL BOARD

3. COOL AIR DISCHARGE

8. AIR INTAKE

4. FRONT GRILLE

 

9. UPPER GUIDE

5. INLET GRILLE

 

10. REMOTE CONTROL

8

Installation Instructions

Window Requirements

NOTE: All supporting parts should be firmly secured to wood, or metal.

1.This unit is designed for installation in standard double hung windows with actual opening widths of 22" to 36". The upper and lower sash must open sufficiently to allow a clear vertical opening of 14" from the bottom of the sash to the window sill.

2.If storm window presents interference, fasten a 2" wide wood strip (OUTER SILL) to the inner window sill across the full width of the sill. The wood strip should be thick enough to raise the height of the window sill so that the unit can be installed without interference by the storm window frame. See Fig. 5-2.Top of wood strip should be approximately 3/4" higher than the storm window frame (STORM WINDOW FRAME) or wood strip (OUTDOORS) to help condensation to drain properly to the outside.

3.Install a second wood strip (approximately 6" long by 11/2" wide and same thickness as first strip) in the center of the outer sill flush against the back off the inner sill. This will raise theL bracket as

shown Fig. 5-2.

4.If the distance between STORM WINDOW FRAME and WOOD STRIP MOUNTED ON TOP OF INNER SILL is more than 1", two of wood strip are not necessary.

 

 

 

 

 

L BRACKET

INNER

 

WOOD STRIP MOUNTED

1" MAX.

3/4"

SILL

 

ON TOP OF INNER SILL

 

 

 

 

 

 

CLEARANCE

 

 

 

 

 

STORM

 

 

 

INNER

 

WINDOW

 

 

 

 

FRAME

 

 

 

SILL

 

 

 

 

 

WOOD STRIP

 

 

 

 

FOR L BRACKET

 

 

 

OUTER

 

 

OUTER

 

 

SILL

 

 

SILL

INDOORS

Fig. 5-1

OUTDOORS

INDOORS

Fig. 5-2

OUTDOORS

 

 

 

 

Installation

 

 

 

HARDWARE

 

 

 

TYPE A: 11EA

TYPE B: 5EA

 

TYPE C: 3EA

(SHORT SCREW)

(WOOD SCREW)

(L BRACKET)

10mm

16mm

 

 

TYPE D: 1EA

TYPE E: 1EA

TYPE F: 2EA

TYPE G: 1EA

(SEAL STRIP)

(SASH SEAL)

(GUIDE PANEL)

(SUPPORT BRACKET)

(Adhesive backed)

(Not adhesive backed)

 

 

ENGLISH

9

A. BEFORE INSTALLATION

1.Insert the guide panels into the guides of the air conditioner. Fasten the curtains to the unit with screws (TYPE A) as shown Fig. 6.

2.Cut the adhesive-backedseal strip (TYPE D) to match the window width.

Remove the backing from the seal strip and attach the seal strip to the underside of the bottom window. (Fig. 7)

B. BEGIN INSTALLATION

1. LOCATING UNIT IN WINDOW

Open the window and mark center line on the center of the inner sill, as shown in Fig. 8.

2.ATTACH L BRACKET

a.Install the L brackets behind the inner window sill, with the short side of bracket as shown. Use the 2 screws (TYPE A) provided.

b.The bracket helps to hold unit securely in place. Be sure to place bracket edge flush against back of inner sill. See Fig. 9.

3.INSTALL THE AIR CONDITIONER IN THE WINDOW

a.Carefully lift the air conditioner and slide it into the open window. Make sure the bottom guide of the air conditioner drops into the notches of the L bracket. See Fig. 9.

CAUTION

During the following step, hold unit firmly until window sash is lowered to top channel behind side panel frames. Personal injury or property damage may result if unit falls from window.

IMPORTANT :

When the air conditioner drops into the L bracket, the air conditioner will be centered in window opening as shown in Fig. 10.

TYPE A

Fig. 6

TYPE A

 

SEAL STRIP (TYPE D)

Fig. 7

CENTER LINE

INNER SILL

ROOM SIDE

Fig. 8

INNER SILL

OUTER SILL

TYPE A INSIDE

 

CENTER LINE

 

8"

SHORT SIDE

8"

OUTSIDE

 

L BRACKET

Fig. 9

 

CENTER LINE

Fig. 10

10