Service Questions: Contact Friedrich at (800) 541-6645
Sales Inquiries: Contact Sylvane at (800) 934-9194 or visit sylvane.com
Breeze™
A revolution in room cooling
Installation Instructions
for BRO412W1A
4000 - 12000 Btu
Friedrich Part No. 96091000 (Rev. 01)
What’s in the carton?
1.Breeze indoor module with 25 ft. connecting line attached
2.Wall mounting template and bracket for indoor module
3.Breeze outdoor module
4.Outdoor module connection covers
5.Mounting pad for outdoor module
6.Remote control
7.Accessories (see list at right)
Tools you will need:
•Phillips screwdriver
•1/2” wrench or crescent wrench
•Drill with Phillips bit and 3/16” drill bit
•Stud finder (recommended)
•3” hole saw (through wall installations)
•Safety glasses (recommended)
•Trim knife
•Level
Before getting started
Identify the locations where you will mount the indoor module and place the outdoor module. Keep in mind, there is 25’ of connection line for connecting indoor and outdoor pieces, so locate them accordingly. You cannot add additional length if they are too far apart.
Placing the indoor unit
It is recommended that you install the indoor module on an exterior wall within 6 feet of a properly rated outlet for the system you are installing. The BR0412W1A plugs into a 115V 15A outlet. The system should be plugged into a single circuit outlet only. Typically, hanging the indoor module above or adjacent to a window will provide a great location. NOTE: You should not drill through the window header (part of the rough framing) located directly above the window opening.
Placing the outdoor unit
The outdoor module should be placed on a level surface with adequate clearance from items like shrubbery, solid fencing or other air conditioning equipment that can impede airflow to the module.
The outdoor module must be at least 12” from the wall for proper airflow. The mounting pad provided with the system will raise the module off of the ground 3”. The fan should face away from the building.
Accessories
ITEM |
DESCRIPTION |
|
|
QTY |
1. |
CONTROL BOX COVER DOOR |
|
|
1 |
2. |
CONTROL BOX COVER |
|
|
1 |
3. |
WIRE TIE |
|
|
2 |
4. |
CONNECTING LINE BENDING GUIDE |
|
1 |
|
5. |
ELECTRICAL CORD RETENTION BRACKET |
1 |
||
6. |
WALL OPENING FILL GASKET |
|
|
1 |
7. |
OUTDOOR UNIT WASHER FOR ANCHOR SCREW |
4 |
||
8. |
OUTDOOR UNIT ANCHOR SCREW |
|
|
4 |
9. |
SCREW #8 X 3/4” TRUSS HEAD |
|
|
6 |
10. |
SCREW #8 X 1 1/2” PHILLIPS PAN HEAD |
|
15 |
|
11. |
WALL ANCHOR FOR #8 X 1 1/2” SCREW |
|
15 |
|
12. |
SECURITY SCREW |
|
|
1 |
1. 13. |
CONNECTING LINE CLIPS |
|
|
5 |
2. |
3. |
|
13. |
|
|
|
|
|
|
|
|
12. |
|
|
|
8. |
10. |
|
|
|
|
|
|
|
|
6. |
|
|
|
|
4. |
|
11. |
|
|
|
|
|
|
|
|
|
9. |
|
|
|
7. |
|
|
|
5. |
|
|
|
NOTE:
Be sure to place your equipment with these limitations in mind.
25 ft. connecting
line
6 ft. power cord
6" min |
. |
|
6" |
minimum |
clearance |
|
|
6" |
min |
. |
|
25 ft. max. |
6 ft. |
|
|
|
power |
|
cord |
12" minimum |
|
clearance |
|
DO NOT PLUG IN INDOOR UNIT until you have completed the entire installation process.
CAUTION
SHOCK HAZARD - DO NOT PLUG-IN indoor unit until all installation work is completed! Connect to a single dedicated circuit sized for the load.
DO NOT kink or bend refrigeration line-set less than 3” radius – A connecting line bending guide is provided. Line-set is under high pressure – DO NOT Puncture line-set.
DO NOT Heat line-set.
Always follow all local and national codes when installing equipment. Obtain the help of trained, skilled worker where necessary.
STEP 1 - Determine how you will connect the indoor and outdoor modules. There are two options available:
OPTION 1 is to drill a 3” hole through the wall to pass the connecting line through.
OPTION 2 is to use the Friedrich SimpleSill™ kit to pass the connecting pipe through the window. The SimpleSill™ is an optional accessory available where Breeze is sold.
DO NOT PLUG IN INDOOR UNIT until you have completed the entire installation process.
Loading...