Follett FZR User Manual

0 (0)

FZR Series

Undercounter Freezer

Order parts online www.follettice.com

Installation, Operation and Service Manual

Serial numbers C45184 and above

Following installation, please forward this manual to the appropriate operations person.

801 Church Lane • Easton, PA 18040, USA

 

Toll free (800) 523-9361 • (610) 252-7301

 

Fax (610) 250-0696 • www.follettice.com

00193474R00

2

Welcome to Follett

Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this product delivers that same degree of service, we ask that you take a moment to review this manual before beginning the installation. Should you have any questions or require technical help at any point, please call our technical service group at (800) 523-9361 or (610) 252-7301.

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing of a claim, if necessary.

Specifications

Series specifications

FZR5

34" height for freestanding use or installation below standard 36" (915mm) high counter 4.0 cu ft (usable cubic volume)

FZR4-ADA

31.25" height for freestanding use or installation below 34" (864mm) high ADA-compatible counter 3.3 cu ft (usable cubic volume)

Electrical specifications

115V, 60Hz, 1 phase

Full load amps: 8.0

Minimum circuit ampacity: 15 amp

Maximum size of branch circuit overcurrent device: 15 amp

Refrigeration specifications

Refrigerant – R404A

Charge size – 10 oz

Maximum design pressures:

High side – 383psi

Low side – 175psi

Installation specifications

Ambient temperature must not exceed 100 F (38 C).

The front louvered panel must be kept free of any cabinet trim or obstructions to ensure proper ventilation of the refrigeration system.

Important cautions

Equipment must be wired according to local and NEC codes.

Always disconnect power before servicing freezer.

3

Follett FZR User Manual

Installation

Installing legs – required Fig. 1

1. Remove legs from plastic bag packed inside freezer.

2. Tip freezer back and screw legs in all the way to stop (they will extend 1/8" below base of freezer).

3. Adjust legs as needed to level freezer in both directions. To access legs, remove the lower front panel. Turn legs clockwise to extend legs.

Installing shelves – required

1.Remove shelves and shelf brackets packed inside freezer.

2.Install shelf brackets in pilasters (insert top tab, squeeze and push in lower tab).

Fig. 2

2

1

3

Changing temperature controller settings – optional

Fig. 3

Follett’s temperature controller is pre-programmed with a -25 C (-13 F) set point and degrees C display. The -25 C (-13 F) set point delivers a temperature range of -23 to -25 C (-9 to -13 F). Follett’s controller set point

can be changed to deliver up to a -15 C (+5 F) temperature for applications where a lower temperature is not desired (i.e. ice cream). See page 6 to change controller settings.

4

Reversing the door swing – optional

NOTICE

When reinstalling latch and hinge screws, 242 blue Loctite* MUST be applied to screws. Torque screws to 25 in-lbs.

1.Remove screws and latch from refrigerator cabinet (Fig. 4.1).

2.Use flat screwdriver to carefully remove (do not scratch) hinge covers (Fig. 5.1).

3.Support door and remove screws attaching hinge to refrigerator cabinet (Fig. 5.2).

4.Cover hinge screw holes with screw hole plugs removed from opposite side.

5.Reverse door. Apply 242 blue Loctite to hinge screws and reinstall torqued to 25 in-lbs.

6.Reinstall latch on opposite side.

7.Remove screws and handle from door (Fig. 6.1).

8.Rotate handle (Fig. 6.2).

9.Apply 242 blue Loctite to latch screws and reinstall torqued to 25 in-lbs.

Fig. 4

1

2

Fig. 5

2

1

Fig. 6

1

1

2

Loctite is a registered trademark of Henkel Corporation in the United States and other countries.

5

Controller operation

In normal operation the controller displays cabinet temperatures in degrees C (default) or user-selected degrees F. Degrees C temperatures are displayed to 1 decimal point.

Rocker buttons to the right of the temperature display control all programming functions.

The controller is pre-programmed with a -25 C (-13 F) set point which provides a compressor cut-in at -23 C (-9 F) and cut-out at -25 C (-13 F). The controller set point can be raised to -15 C (+5 F) for nourishment applications where a lower temperature is not desired (i.e. ice cream). Follow instructions for changing temperature cut-out below.

Fig. 7

refrigeration

evaporator

system

fan

energized

energized

°C

- 25

defrost

All set points have a 2 C differential. The 2 C differential means that with a -25 C set point, for example, the compressor will turn off at -25 C (-13 F) and turn on when it reaches -23 C (-9 F).

To display temperature cut-out

STEP

INPUT

DISPLAY

1

Press and release SET

Current cut-out temperature will display for approximately 5 seconds.

 

 

Display will return to current refrigerator temperature.

 

 

 

To change temperature cut-out

STEP

INPUT

DISPLAY

 

 

 

1

Press and hold SET for

Current cut-out temperature displayed and °C (°F) will flash

 

3 seconds

 

 

 

 

2

Press UP or DOWN arrows to

New cut-out temperature displayed

 

desired cut-out temperature

 

 

 

 

3

Press and release SET

New cut-out temperature blinks three times, then current refrigerator

 

 

temperature will display

 

 

 

To change temperature display from degrees C to degrees F

Follett includes a programming key (part# 00193375) that changes the display and temperature settings from degrees C to degrees F.

Programming freezer from a degree F key (download)

1.TURN OFF freezer.

2.Remove 6 screws from panel holding controller to access back of controller.

3.Insert degree F programmed key into 5 PIN receptacle on controller back.

4.TURN ON freezer.

5.Values from key automatically download to freezer (“dol” message blinks followed by “end”).

6.After 10 seconds display returns to current freezer temperature and controller will restart with new values.

7.TURN OFF.

8.Remove key.

9.Reinstall panel.

Note: An “Err” message displays for failed programming. Turn freezer OFF then ON to restart download, or remove key to abort.

6

Loading...
+ 14 hidden pages