FMI PFS DVF36NH-HA User Manual

Size:
3.28 Mb
Download

Direct-ventFIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

PFS ®

US

MODELS (V)dvf36ns, (V)dvf36ps, (V)dvf36nh, (V)dvf36ph, dvf-36ns-ha,dvf36nh-ha,(V)dvf42ns, (V)dvf42ps, (V) dvf42nh, (V)dvf42ph,dvf-42ns-ha,anddvf42nh-ha

WARNING: If the information in this manual is not followedexactly,afireorexplosionmayresultcausing property damage, personal injury or loss of life.

Do not store or use gasoline or other ­flammable vaporsandliquidsinthe­vicinityofthisoranyother appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Donottouchanyelectricalswitch;donotuseany phone in your building.

Immediatelycallyourgassupplierfromaneighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installationandservicemustbeperformedbyaqualified installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance CONSUMER: Retain this manual for future reference.

For more information, visit www.fmiproducts.com

Table of Contents

Safety...................................................................

2

Local Codes.........................................................

4

Product Identification............................................

5

Product Features..................................................

5

Pre-installation.....................................................

6

Location of Termination Cap................................

8

Requirements for the Commonwealth of

.

  Massachusetts..................................................

9

Venting Installation.............................................

10

Fireplace Installation..........................................

16

Operation...........................................................

22

Inspecting Burners.............................................

24

Cleaning and Maintenance................................

24

Troubleshooting.................................................

26

Specifications.....................................................

29

Wiring Diagram..................................................

29

Parts...................................................................

30

Replacement Parts.............................................

36

Technical Service...............................................

36

Service Hints......................................................

36

Acessories..........................................................

36

Warranty...............................................

Back Cover

Safety

WARNING: Improper installation, adjustment, alteration, service or maintenance can causeinjuryorpropertydamage.

Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

This appliance is only for use withthetypeofgasindicatedon the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.

WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects or other reproductive harm.

IMPORTANT: Read this owner’s manualcarefullyandcompletely before trying to assemble, operate or service this fireplace. Improper use of this fireplace can cause serious injury or death from burns, fire, explosion,electricalshockandcarbon monoxide poisoning.

DANGER:Carbonmonoxide

poisoning may lead to death!

This vented gas fireplace is a sealed combustion gas fireplace designed for residential applications.This fireplace must be installed with FMI PRODUCTS, LLC vent pipe components and terminations.

This fireplace complies with the National

Safety Standards and is listed and tested by

PFS Corporation to ANSI Z21.50 standard as vented gas fireplace.

This fireplace must be installed by a qualified (certified or licensed) service person. It brings in fresh air for combustion through the outer pipe and combustion gases are exhausted through the inner pipe. If the glass door assembly and venting pipe are not properly seated, connected and sealed, carbon monoxide leakage (spillage) can occur.

2

www.fmiproducts.com

125078-01B

Safety

Continued

Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness or nausea. If you have these signs, the fireplace may not be working properly. Get fresh air at once!

Have fireplace serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LPgas are odorless.An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this fireplace.

WARNING: Any change to thisfireplaceorit’scontrolscan be dangerous. Do not modify this fireplace under any circumstances. Any parts removed for servicingmustbereplacedprior to operating fireplace.

WARNING:Donotuseablower insert, heat exchanger insert orotheraccessorynotapproved for use with this fireplace.

WARNING: This appliance is only for use with the type of gasindicatedontheratingplate. Thisapplianceisnotconvertible for use with other gases unless a certified kit is used.

WARNING: Do not allow fans toblowdirectlyintothefireplace. Avoidanydraftsthatalterburner flame patterns.

Due to high temperatures, the applianceshouldbelocatedout oftrafficandawayfromfurniture and draperies.

Do not place clothing or other flammable material on or near the appliance. Never place any objects on the appliance.

Donotusethisfireplacetocook foodorburnpaperorotherflammable material.

Thisfireplacereacheshightemperatures. Keep children and adults away from hot surface to avoidburnsorclothingignition. Fireplace will remain hot for a time after shutdown. Allow surface to cool before touching.

Carefully supervise young children when they are in the room with fireplace.

Keep the area around your fireplace clear of combustible materials, gasoline and other flammable vapor or liquids. Do not run fireplace where these are used or stored.

125078-01B

www.fmiproducts.com

3

Safety

Continued

1.For propane/LP fireplace, do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors. To prevent performance problems, do not use propane/LPfuel tank of less than 100 lb. capacity.

2.If you smell gas

shut off gas supply

do not try to light any appliance

do not touch any electrical switch; do not use any phone in your building

immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier's instructions

if you cannot reach you gas supplier, call the fire department.

3.Never install the fireplace

in a recreational vehicle

in windy or drafty areas where curtains or othercombustible(flammable)objectscan make contact with the fireplace front

in high traffic areas

4.Turn fireplace off and let cool before servicing, installing or repairing. Only a qualified service person should install, service or repair this fireplace. Have fireplace inspected annually by a qualified service person.

5.You must keep control compartments, burners and circulating air passages clean. More frequent cleaning may be needed due to excessive lint and dust from carpeting, bedding material, etc. Turn off the gas valve and pilot light before cleaning fireplace.

6.Haveventingsysteminspectedannuallyby a qualified service person. If needed, have venting system cleaned or repaired. See

Cleaning and Maintenance, page 24.

7.Do not use any solid fuels (wood, coal, paper, cardboard, etc.) in this fireplace. Use only the gas type indicated on fireplace nameplate.

8.This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.

9.Do not use fireplace if any part has been exposed to or under water. Immediately call a qualified service person to arrange for replacement of the unit.

10.Do not operate fireplace if any log is broken.

11.Do not operate fireplace with glass door removed, cracked or broken.

12.Provide adequate clearances around air openings.

Local Codes

Install and use fireplace with care. Follow all local codes. In the absence to local codes, use the current National Fuel Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

4

www.fmiproducts.com

125078-01B

Product Identification

 

Flue Collar

Outer

 

Glass Door

 

Herringbone Brick

 

Refractories

Nailing Flange

 

Log Set

 

Grate

 

Lower Door/

 

Control Cover

 

Figure 1 - Direct Vent Fireplace

Product Features

These are a few facts that can help you understand and enjoy your direct vent fireplace:

The venting system may be routed to the outside of your home in several ways. It may vent through the roof (vertical) or it may vent to an outside/exterior wall (horizontal). The vent pipe installation is very important to allow for proper operation.

You must follow the venting instructions very carefully for either vertical or horizontal applications.

This fireplace may be installed in any room of your house provided all local codes and these installation instructions are followed.

Each time you turn on your fireplace, you may notice some amount of condensation on the inside of the fireplace glass. This is normal and will disappear after 10-20minutes of operation.

Your direct vent gas fireplace system

(fireplace and venting) is a balanced and sealed gas operating unit. It requires approximately 10-20minutes of operating time before the flame pattern stabilizes.

125078-01B

www.fmiproducts.com

5

Pre-installation

Location and space requirements

Determine the safest and most efficient location for your direct vent fireplace. Make sure that rafters and wall studs are not in the way of the venting system. Choose a location where the heat output is not affected by drafts, air conditioning ducts, windows or doors. Figure 2 shows some common locations. Be aware of all restrictions and precautions before deciding the exact location for your fireplace and termination cap.

When deciding the location of your fireplace, follow these rules:

Do not connect this fireplace venting to a chimney flue serving a separate solid-fuelburning fireplace or appliance.

Due to high temperatures, do not locate this fireplace in high traffic areas, windy or drafty areas or near furniture or draperies.

Proper clearances must be maintained.

If your fireplace is to be installed directly on carpeting,vinyltileoranycombustiblematerial other than wood, it must be installed on a metal or wood panel extending the full width and depth of the fireplace (see Figure 3).

Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on back, sides or top of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing material. See framing details, page 7.

When locating termination cap, it is important to observe the minimum clearances shown in Figure 7, page 8.

If recessing into a wall, you can avoid extra framingbypositioning yourfireplace against an already existing framing member.

Do not recess termination cap into a wall or siding.

You may paint the termination cap with 450º F (232º C) heat-resistantpaint to coordinate with the exterior finish.

There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24" from the front of the termination cap and the front of outside air vent.

Do not locate termination cap and outside air vent where excessive snow or ice build up may occur. Be sure to clear vent termination area after snow falls to prevent accidental blockage of venting system. When using snow blowers, do not direct snow towards vent termination area.

Flush with a wall

Through exterior wall enclosed in a chase

Corner installation

Figure 2 - Common Fireplace Locations

29" (36") 34 3/4" (42")

21" (36") 25" (42")

117/8" (36") 135/8" (42")

41 1/4" (36")

48 1/4" (42")

Figure 3 - Fireplace Top Dimensions

6

www.fmiproducts.com

125078-01B

Pre-Installation

Continued

Clearances

Minimum clearances to combustibles for the fireplace are as follows:

*Back and sides

1"

Perpendicular walls

6"

Floor

0"

Ceiling to louver opening

42"

Front

36"

Top of Standoffs

0"

Vent

(See venting instructions

 

for specific venting

 

clearances.)

Combustible material with a maximum thickness of 5/8" may be flush with the top front of fireplace.

* For back and sides of fireplace, do not pack with insulation or other materials. 1" clearance not required at nailing flanges.

NOTICE:Thisfireplaceisintendedforuseassupplementalheat. Use this fireplace along with your primary heating system. Do not install this fireplace as your primary heat source. If you have a central heating system, you may run system’s circulatingblowerwhileusingfireplace. This will help circulate the heat throughout the house.

43

1

/4" (36")

47

1

/4" (42")

41 1/2" (36")

48 1/2" (42")

Figure 4 - Framing Clearances with Outside Air Flex Duct

 

51 3/8" (36")

36 3/8" (36")

61 3/4" (42")

43 3/8" (42")

Nailing

 

Tabs

15 3/4"

 

(36")

42" (36"), 49" (42")

19" (42")

43" (36"), 50" (42")

 

Figure 5 - Framing Clearances for Corner Installation

Framing and finishing

Figure4showstypicalframingofthisfireplace. Figure 5 shows framing for corner installation. All minimum clearances must be met.

If you are using a separate combustible mantel piece, refer to Figure 6 for proper installation height. You can install noncombustible mantels at any height above the fireplace.

Note: Noncombustible mantels may discolor!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ref.

Mantel

Ref.

 

 

Mantel from

 

 

Depth

Top of Opening

 

 

 

1

14"

 

 

A

 

16"

 

 

 

 

 

 

 

 

 

 

2

12"

 

 

B

 

14"

 

 

 

 

 

 

 

 

 

 

3

10"

 

 

C

 

12"

 

 

 

 

 

 

 

 

 

 

4

8"

 

 

D

 

10"

 

 

 

 

 

 

 

 

 

 

5

6"

 

 

E

 

8"

 

 

 

 

 

 

 

 

 

 

 

6

4"

 

 

F

 

6"

 

 

 

 

 

 

 

 

 

 

 

7

2"

 

 

G

 

 

4"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 6 - Clearances for Combustible Mantels

125078-01B

www.fmiproducts.com

7

Location of Termination Cap

D

E V

B L

 

 

 

 

 

 

H

 

C

 

 

 

 

 

 

Fixed

V

 

B

V

I

 

Closed

Openable

Fixed

 

 

 

Openable

 

 

Closed

 

 

F

 

 

 

B

 

V

 

 

 

 

 

B

V J

X

G

B

 

A

 

M

 

 

 

N N

 

G

 

V

 

G

V K X

V

 

 

 

 

 

 

 

 

 

 

 

A

 

 

V TERMINATION CAP

X AIR SUPPLY INLET

 

G

GAS METER

 

 

RESTRICTED AREA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(TERMINATION PROHIBITED)

A

=

clearance above grade, veranda, porch, deck, or

I

=

clearance to service regulator vent outlet [*72" (182.9 cm)

 

 

balcony [*12" (30.5 cm) minimum]

 

 

 

minimum]

 

 

 

B

=

clearance to window or door that may be opened

J

=

clearance to non-mechanicalair supply inlet to building

 

 

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

 

 

or the combustion air inlet to any other fireplace

 

 

if between 10,000 and 50,000, 12" (30 cm) in Canada

 

 

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

 

 

if between 10,000 and 100,000; 12" (30 cm) in US if

 

 

if between 10,000 and 50,000, 12" (30 cm) in Canada

 

 

greater than 50,000, 36" (91 cm) in Canada if greater

 

 

if between 10,000 and 100,000; 12" (30 cm) in US if

 

 

than 100,000]

 

 

 

greater than 50,000, 36" (91 cm) in Canada if greater

C

=

clearance to permanently closed window

 

 

 

than 100,000]

 

 

 

 

 

[minimum 12" (30.5 cm) recommended to prevent

K

=

clearance to a mechanical air supply inlet [*In Canada,

 

 

condensation on window]

 

 

 

6 ft. (1.83m) minimum; In US 3 ft. (91 cm) above if within

D

=

vertical clearance to ventilated soffit located above the

 

 

10 ft. (3 m) horizontally]

 

 

 

 

 

terminal within a horizontal distance of 24" (61 cm) from L

=

† clearance above paved side-walkor a paved driveway

 

 

the center-lineof the terminal [18" (45.7 cm) minimum]

 

 

located on public property [*84" (213.3 cm) minimum]

E

=

clearance to unventilated soffit [12" (30.5 cm) minimum] M =

clearance under veranda, porch, deck

F

=

clearance to outside corner (see below)

 

 

 

[*12" (30.5 cm) minimum ‡]

G

=

clearance to inside corner (see below)

 

N =

clearance above a roof shall extend a minimum of

H

=

*not to be installed above a meter/regulator assembly

 

 

24" (61 cm) above the highest point when it passes

 

 

within 36" (91.4 cm) horizontally from the center line

 

 

through the roof surface and any other obstruction within

 

 

of the regulator

 

 

 

a horizontal distance of 18" (45.7 cm)

vent shall not terminate directly above a side-walkor paved driveway which is located between two single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor* * as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Inside Corner

Outside Corner

Recessed Location

 

 

 

D

 

 

 

C

C

A

A = 6" (15.2 cm)

 

E

 

 

V

V

V

 

 

 

B = 6" (15.2 cm)

B

Balcony with No Side Wall

Balcony with Perpendicular Side Wall

G

V

G = 12" (30.5 cm) minimum clearance

H

V

J

Combustible &

Noncombustible H = 24" (61 cm) J = 20" (50.8 cm)

C = Maximum depth of 48" (121.9 cm) for recessed location

D = Minimum width for back wall of recessed location - Combustible - 38" (965 mm) Noncombustible - 24" (61 cm)

E = Clearance from corner in recessed locationCombustible - 6" (15.2 cm) Noncombustible - 2" (5.1 cm)

Figure 7 - Minimum Clearances for Termination Cap

8

www.fmiproducts.com

125078-01B

Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipmentinstalledineverydwelling,buildingor structure used in whole or in part for residential purposes,includingthoseownedoroperatedby the Commonwealth and where the side wall exhaustventterminationislessthanseven(7)feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

INSTALLATION OF CARBON

MONOXIDE DETECTORS

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery backup is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observethatabatteryoperatedorhardwiredcarbon monoxide detector with an alarm is installed oneachadditionallevelofthedwelling,buildingor structureservedbythesidewallhorizontalvented gasfueledequipment.Itshallbetheresponsibility of the property owner to secure the services of qualifiedlicensedprofessionalsfortheinstallation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

SIGNAGE

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than 1/2" in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS".

INSPECTION

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a) 1 through 4.

EXEMPTIONS:The following equipmentisexempt from 248 CMR 5.08(2)(a) 1 through 4:

The equipment listed in Chapter 10 entitled

"Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

Acomplete parts list for the venting system design or venting system.

Gas Equipment Venting System Not

Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:

The referenced "special venting system" instructionsshallbeincludedwiththeappliance or equipment installation instructions; and

The"specialventingsystems"shallbeProduct Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all

Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

125078-01B

www.fmiproducts.com

9

Venting Installation

NOTICE: Read these instructionscompletelybeforeattempting installation.

These models are tested and approved for use with FMI PRODUCTS, LLC (direct vent) pipe components and terminations.

The venting system must terminate on the outside of the structure and can not be attached to a chimney or flue system serving a separate solid fuel or gas burning appliance.

A direct vent appliance must have its own venting system. DO NOT common vent this appliance.

These models are approved to be vented either horizontally through an outside wall or vertically through a roof or chase enclosure using the following guidelines:

When venting system terminates horizontally on an outside wall, you may install a standoff if the termination cap is to be installed directly on a combustible finish such as vinyl, wood, stucco, etc.

Never run the vent downward as this may cause excessive temperatures which could cause a fire.

Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal sections, which requires 2" clearance from the top of the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.

Have fireplace and selected vent components on hand to help determine the exact measurements when elbowing or offsetting.

Always use wall firestops when penetrating walls and firestops when penetrating ceilings or attic spaces.

For installation of fireplace at elevations of

4000 feet or greater, pay special attention to venting requirement recommendations.

WARNING: Read all instructionscompletelyandthoroughly before attempting installation.

Failure to do so could result in seriousinjury,propertydamage or loss of life.

NOTICE:Failuretofollowtheseinstructions will void the warranty.

NOTICE:Donotsealtermination cap to vent pipe. Cap must be removable for vent inspection and maintenance.

Installation Precautions

Wear gloves and safety glasses for protection

Use extreme caution when using ladders or when on roof tops

Be aware of electrical wiring locations in walls and ceilings

The following actions will void the warranty on your venting system:

Installation of any damaged venting component

Unauthorizedmodificationoftheventingsystem (Do not cut or alter vent components)

Installation of any component part not manufactured or approved by FMI

PRODUCTS, LLC

Installation other than as instructed by these instructions

WARNING:Thisgasfireplace and vent assembly must be vented directly to the outside. TheventingsystemmustNEVER be attached to a chimney servingaseparatesolidfuelburning appliance. Each direct vent gas appliance must use a separate vent system. Do not use common vent systems.

WARNING: Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal sections, which require 2" clearances from the top of the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.

10

www.fmiproducts.com

125078-01B