FMI CGMFP User Manual

Size:
1.98 Mb
Download

UNVENTED (VENT-FREE)Gas

Mini Compact Fireplace

OWNER’S OPERATION AND INSTALLATION MANUAL

Shown with Optional Cabinet Mantel/Hearth

Base Accessory

PFS ®

US

Manual Models CGMFN and CGMFP

Remote-ReadyModels VGMRN and VGMRP

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other ­flammable vapors and liquids in the ­vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Donottouchanyelectricalswitch;donotuseany phone in your building.

Immediatelycallyourgassupplierfromaneighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installationandservicemustbeperformedbyaqualified installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

For more information, visit www.fmiproducts.com

TABLE OF CONTENTS

Safety Information................................................

2

Local Codes.........................................................

4

Unpacking............................................................

4

Product Identification............................................

5

Product Features..................................................

5

Optional Remote Control Accessories.................

5

Assembly..............................................................

5

Air for Combustion and Ventilation.......................

6

Installation............................................................

9

Operating Fireplace............................................

18

Inspecting Burners.............................................

23

Cleaning and Maintenance.

...............................

24

Troubleshooting.................................................

 

25

Specifications.....................................................

 

29

Wiring Diagram..................................................

 

29

Service Hints......................................................

 

29

Technical Service...............................................

 

29

Replacement Parts.............................................

 

29

Illustrated Parts Breakdown ........and Parts List

30

Accessories........................................................

 

34

Warranty................................................

Back cover

Safety Information

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

Refer to this manual for correct installation and operational procedures.

For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING: This is an unvented gas-firedheater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer toAir for Combustion and Ventilation section on page 6 of this manual.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

WARNING:Thisproductcontainsand/orgenerateschemicals known to the State of California to cause cancer or birth defects or other reproductive harm.

IMPORTANT: Read this owner’s manualcarefullyandcompletely before trying to assemble, operate or service this fireplace. Improper use of this fireplace can cause serious injury or death from burns, fire, explosion,electricalshockandcarbon monoxide poisoning.

2

www.fmiproducts.com

119315-01D

SAFETY INFORMATION

Continued

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness or nausea. If you have these signs, the fireplace may not be working properly. Get fresh air at once! Have fireplace serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LP gases are odorless. An odormaking agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this fireplace.

WARNING: Any change to this fireplace or its controls can be dangerous.

WARNING:Donotuseablowerinsert,heatexchangerinsertor otheraccessorynotapprovedfor use with this fireplace.

WARNING: Do not allow fans toblowdirectlyintothefireplace.

Avoidanydraftsthatalterburner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.

Due to high temperatures, the applianceshouldbelocatedout oftrafficandawayfromfurniture and draperies.

Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.

Fireplace front and screen become very hot when running heater.Keepchildrenandadults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in the room with fireplace. When using the hand-heldremote accessory

(Remote-ReadyModels Only), keep selector switch in the OFF positiontopreventchildrenfrom turning on burners with remote.

You must operate this fireplace withthefireplacescreeninplace.

Make sure fireplace screen is closed before running fireplace.

Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

1.This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

2.Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors.

3.If you smell gas

shut off gas supply

do not try to light any appliance

do not touch any electrical switch; do not use any phone in your building

immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions

if you cannot reach your gas supplier, call the fire department

119315-01D

www.fmiproducts.com

3

SAFETY INFORMATION

Continued

4.This fireplace shall not be installed in a bathroom.

5.Do not use this fireplace as a wood-burn-ing fireplace. Use only the logs provided with the fireplace.

6.Do not add extra logs or ornaments such as pine cones, vermiculite or rock wool.

Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of fireplace.

7.Thisfireplaceisdesignedtobesmokeless. If logs ever appear to smoke, turn off fireplace and call a qualified service person. Note: During initial operation, slight smoking could occur due to log curing and fireplace burning manufacturing residues.

8.To prevent the creation of soot, follow the instructions in Cleaning and Maintenance, page 24.

9.Before using furniture polish, wax, carpet cleaner or similar products, turn fireplace off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10.This fireplace needs fresh air ventilation to run properly.This fireplace has an Oxygen

Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the fireplace if not enough fresh air is available.

See Air for Combustion and Ventilation, page 6. If fireplace keeps shutting off, see

Troubleshooting, page 25.

11.Keep all air openings in front and at bottom of heater clear and free of debris. This will insure enough air for proper combustion.

12.Do not run fireplace

where flammable liquids or vapors are used or stored.

under dusty conditions.

13.Do not use this fireplace to cook food or burn paper or other objects.

14.Never place any objects in the fireplace or on logs.

15.Do not use fireplace if any part has been under water. Immediately call a qualified service technician to inspect the room fireplace and to replace any part of the control system and any gas control which has been under water.

16.Turn off fireplace and let cool before servicing. Only a qualified service person should service and repair fireplace.

17.Operating fireplace above elevations of 4,500 feet could cause pilot outage.

18.Do not operate fireplace if any log is broken. Do not operate fireplace if a log is chipped (dime-sizedor larger).

19.To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

20.Provide adequate clearances around air openings.

Local Codes

Install and use fireplace with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of

Massachusetts.

Sellers of unvented propane or natural gas-firedsupplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-freegas products are prohibited for bedroom and bathroom installation in the Commonwealth of Massachusetts.

Unpacking

CAUTION:Donotremovedata platesfromgrateassembly.Data plates contain important warranty and safety information.

1.Remove fireplace and hood from carton. Log is wrapped and inside fireplace. Do not remove at this time.

2.Remove all protective packaging applied to fireplace for shipment.

3.Make sure fireplace includes one hardware packet.

4.Check fireplace for any shipping damage. If fireplace is damaged, promptly inform dealer where you bought fireplace.

4

www.fmiproducts.com

119315-01D

Product

Identification

ELECTRONIC IGNITOR

(Remote-ReadyModels Only)

This heater has an electronic ignitor to light heater fuel supply.

Brick

Liners

Screen

Log

Control

Knob

Piezo

Ignitor

Access

Door

Brick

Liners

Screen

Log

Control

Knob

Remote

Control

Electronic

Ignitor

Access Door

Figure 1 - Vent-FreeMini Compact

Fireplace

Product Features

Safety Pilot

This fireplace has a pilot with an Oxygen

Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-freeroom fireplaces. The ODS/pilot shuts off the fireplace if there is not enough fresh air.

Optional Remote Control Accessories

(For Remote-ReadyModels Only)

There are four optional remote controls that can be purchased separately for RemoteReady Models only:

wall switch

hand-heldON/OFF remote

wall thermostat

hand-heldthermostat remote

See Accessories, page 34.

Assembly

WARNING: Always have screeninplacebeforeoperating fireplace. This prevents excessive temperatures on fireplace surfaces.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this fireplace may result in property damage or personal injury.

Assembling Fireplace

Tools Required:

Phillips screwdriver

5/16" hex wrench

slotted screwdriver

scissors

1.Remove two screws that hold fireplace screen in place for shipping. These screws are located near top of screen.

Discard screws. Lift fireplace screen up and pull out to remove (see Figure 2, page

6). Set screen aside until installation has been completed.

2.Remove all packaging from inside of unit.

3.Remove bubble wrap from logs and discard.

119315-01D

www.fmiproducts.com

5

Assembly

Continued

4.Check installation of brick liners. Brick liners are in four pieces: 2 sides, 1 back and 1 top.

5.Place hood under top edge of firebox opening. Use 3 screws from hardware kit to mount hood to firebox (see Figure 3).

Shoulder

Screw

Screen

Figure 2 - Removing and Replacing

Screen

Top Trim

Panel

Hood

Screw

Figure 3 - Assembling Hood

Air for Combustion and Ventilation

WARNING: This fireplace shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustionandventilationair.Read the following instructions to insureproperfreshairforthisandotherfuel-burningappliancesinyour home.

Today’s homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in.

During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burningappliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burningappliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code. ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1.Unusually Tight Construction

2.Unconfined Space

3.Confined Space

The information on pages 6 through 8 will help you classify your space and provide adequate ventilation.

6

www.fmiproducts.com

119315-01D

AIR FOR COMBUSTION

AND VENTILATION

Continued

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a.walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10-11 kg perpa-sec-m2)or less with openings gasketed or sealedand

b.weather stripping has been added on openable windows and doors and

c.caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceilingjoints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other openings.

If your home meets all of these three criteria, you must provide additional fresh air. See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three criteria above, proceed to Determining Fresh-Air Flow For Fireplace Location.

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1/ NFPA 54 defines a confined space as a space whose volume is less than 50 ft3 per 1,000 Btu/hr (4.8 m3/kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 ft3 per 1,000 Btu/hr (4.8 m3/kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

DETERMINING FRESH-AIRFLOW

FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1.Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft. (volume of space)

Example: Space size 16 ft. (length) x 14 ft.

(width) x 8 ft. (ceiling height) = 1792 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2.Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

__________(volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example: 1792 cu. ft. (volume of space) x 20

= 35,840 (maximum Btu/Hr the space can support)

3.Add the Btu/Hr of all fuel burning appliances in the space.

Vent-freefireplace

__________ Btu/Hr

Gas water heater*

__________ Btu/Hr

Gas furnace

__________ Btu/Hr

Vented gas heater

__________ Btu/Hr

Gas fireplace logs

__________ Btu/Hr

Other gas appliances* +__________ Btu/Hr Total =__________ Btu/Hr

* Do not include direct-ventgas appliances.Direct-ventdraws combustion air from the outdoors and vents to the outdoors.

Example:

 

30,000

 

Gas water heater

 

 

 

__________ Btu/Hr

Vent-freefireplace

+

10,000

Btu/Hr

Total

=

40,000

Btu/Hr

4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_ ______ Btu/Hr (maximum the space can support)

________ Btu/Hr (actual amount of Btu/Hr used)

Example: 35,840 Btu/Hr (maximum the space can support)

40,000 Btu/Hr (actual amount of

Btu/Hr used)

119315-01D

www.fmiproducts.com

7

AIR FOR COMBUSTION AND VENTILATION

Continued

The space in the example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A.Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building.

B.Vent room directly to the outdoors. See

Ventilation Air From Outdoors.

C.Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.

WARNING:Iftheareainwhich the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air byoneofthemethodsdescribed in theNational Fuel Gas Code, ANSIZ223.1/NFPA54Section5.3 or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and2,Figure4).Youcanalsoremovedoorinto adjoining room (see option 3, Figure 4). Follow the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

 

 

12"

 

 

Ventilation Grills

Ventilation

 

Into Adjoining Room,

 

Option 2

Grills

Or

 

into

Remove

 

Adjoining

Door into

 

Room,

Adjoining

 

Option 1

Room,

 

 

Option 3

 

 

 

12"

Figure 4 - Ventilation Air from Inside Building

grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermo-stat-controlledpower vent. Heated air entering the attic will activate the power vent.

 

Outlet

Ventilated

 

Attic

 

Air

 

 

Outlet

 

 

Air

 

To Attic

 

 

 

 

To

 

 

Crawl

Inlet

 

Space

 

 

Air

 

 

 

Inlet Air

Ventilated

 

Crawl Space

 

 

Figure 5 - Ventilation Air from Outdoors

8

www.fmiproducts.com

119315-01D

Installation

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a centralheatingsystem,youmay run system’s circulating blower whileusingheater.Thiswillhelp circulatetheheatthroughoutthe house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING:Aqualifiedservice person must install fireplace.

Follow all local codes.

WARNING: Never install the fireplace

in a bathroom

in a recreational vehicle

where curtains, furniture, clothing or other flammable objects are less than 36" from the front, top or sides of the fireplace

as a fireplace insert

in high traffic areas

in windy or drafty areas

CAUTION: This fireplace creates warm air currents. These currents move heat to wall surfacesnexttofireplace.Installing fireplacenexttovinylorclothwall coverings or operating fireplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) intheairexist,maydiscolorwalls or cause odors.

IMPORTANT: Vent-freefireplaces add moisture to the air. Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. SeeAir for Combustion and Ventilation, page 6.

Note: Your fireplace is designed to be used in zeroclearanceinstallations.Wallorframingmaterial can be placed directly against any exterior surfaceontherear,sidesortopofyourfireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Note: When installing fireplace directly on carpeting, tile or other combustible material, other than wood flooring, the fireplace shall be installed on a metal or wood panel extending the full width and depth of the fireplace.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fireplace Installation, page 10).

CHECK GAS TYPE

Use the correct gas type (natural or propane/ LP) for your unit. If your gas supply is not correct, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

WARNING: This appliance is equipped for natural or propane/LP gas but not both. Field conversion is not permitted.

INSTALLATION ITEMS

Before installing fireplace, make sure you have the items listed below.

external regulator (supplied by installer, for propane/LP units only)

piping (check local codes)

sealant (resistant to propane/LP gas)

equipment shutoff valve *

test gauge connection*

ground joint union

sediment trap

tee joint

pipe wrench

* An equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional equipment shutoff valve from your dealer. See Accessories, page 34.

119315-01D

www.fmiproducts.com

9

INSTALLATION

Continued

Fireplace Clearances

WARNING: Maintain the minimum clearances shown in Figure 6. If you can, provide greater clearances from floor, ceiling and joining wall.

NOTICE: If you install the fireplace in a bedroom, some building codes require that the fireplace/mantel system be secured to (or within) a wall. You can position fireplace in an optional cabinet or corner mantel. You can also recess fireplace into the wall.

If your fireplace is to be used with an optional mantel, the installation instructions included with your mantel shows an CSA approved method of attaching the fireplace/mantel system to a wall. IMPORTANT: Only use optional cabinet or corner mantels specified in this manual. Purchase the optional mantel from your dealer (seeAccessories, page 34).

If your fireplace is to be recessed into the wall, see Built-In Fireplace Installation to secure your fireplace into the wall.

CAUTION: If you install the fireplace in a home garage

fireplacepilotandburnermust be at least 18" above floor.

locatefireplacewheremoving vehicle will not hit it.

For convenience and efficiency, install fireplace

where there is easy access for operation, inspection and service

in coldest part of room

MinimumClearancesForSideCombustible

Material, Side Wall and Ceiling

A.Clearances from the side of the fireplace cabinet to any combustible material and wall should follow diagram in Figure 6.

Example: The face of a mantel, bookshelf, etc. is made of combustible material and protrudes 31/2" from the wall. This combustible material must be 4" from the side of the fireplace opening (see Figure 6).

B.Clearances from the top of the fireplace opening to the ceiling should not be less than 36".

C.For mantel clearances, see Figure 9 on page 12.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top

Left and

Bottom and

Front

Right Sides

Rear

36"

6"

0"

36"

 

Example

 

 

 

 

 

*

*Minimum 16" from Side Wall

Figure 6 - Minimum Clearance for Combustible to Wall

Built-InFireplace Installation

Built-ininstallation of this fireplace involves installing fireplace into aframed-inenclosure. This makes the front of fireplace flush with wall. Fireplace face will extend past sides and top of fireplace approximately 1". This will cover the rough edges of the wall opening. If installing abuilt-inmantel above the fireplace, you must follow the clearances shown in Figure 9, page 12. To install the fireplace in this manner, use the following instructions.

10

www.fmiproducts.com

119315-01D

INSTALLATION

Continued

 

Actual

Framing

Height

23 3/4"

22 1/4"

Front Width

19 3/4"

17 1/2"

Depth

8 7/8"

8 7/8"

Bottom

0"

0"

1.Frame in rough opening. Use dimensions shown in Figure 7 for the rough opening.

If installing in a corner, use dimensions shown in Figure 8 for the rough opening. The height is 22 1/4" which is the same as the wall opening above.

2.Install gas piping to fireplace location.This installation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping.

3.If you have not assembled firebox, follow instructions on page 6.

4.Carefully set fireplace in front of rough opening with back of fireplace inside wall opening.

5.Attach flexible gas line to fireplace gas regulator. See Connecting Fireplace to Gas Supply, page 14.

6.Check all gas connections for leaks. See

Checking Gas Connections, page 15.

8 7/8"

221/4"

171/2"

Figure 7 - Rough Opening for Installing in Wall

297/8"

211/8"

171/2"421/4"

Figure 8 - Rough Opening for Installing in Corner

IMPORTANT: When finishing your firebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top edge of the firebox. Combustible materials should never overlap the firebox front facing.

WARNING: Do not allow any combustibleornoncombustible materials to overlap the firebox front facing.

WARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

WARNING: Never modify or cover the louvered slots on the front of the firebox.

Mantel Clearances for Built-InInstallation

If placing mantel above built-infireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation.

Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clearances shown in Figure 9, page 12, you must do one of the following:

raise the mantel to an acceptable height

remove the mantel

119315-01D

www.fmiproducts.com

11

INSTALLATION

Continued

 

9"

 

 

Mantel Shelf

Note:

 

 

 

 

3"

 

 

 

 

All vertical

 

 

 

 

measurements

1"

 

 

 

 

 

 

 

 

are from top of

 

 

 

 

 

 

 

 

 

fireplace

3/4"

 

 

 

 

opening to

 

 

 

 

 

bottom of

 

 

 

 

 

mantel shelf. All

 

 

 

 

 

measurements

 

 

 

 

 

are in inches.

"

 

 

 

 

 

 

 

 

 

 

4

 

 

18"

 

 

3 1/

6"

9"

 

 

 

 

 

 

 

Side of Firebox

Hearth

Pipe and Gas

Electrical

Shutoff Valve

Outlet

Base

 

 

Figure 10 - Placing Hearth Base Against Wall

Cabinet

Mantel

Figure 9 - Minimum Mantel Clearances for Built-InInstallation

OPTIONAL MANTEL Installation

Refer to instructions provided with the mantel for assembly. Refer to the following instructions for system installation. Refer to instructions on page 6 for hood assembly.

1.Assemble cabinet mantel as shown in accessory instruction sheet.

2.Place hearth base against wall at installation location. Cut an access hole in hearth base to run gas line to fireplace (see Figure 10).

Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You cansecurebasetofloorusingwoodscrews.

Countersink screw heads and putty over.

3.Route flexible gas line through access hole in hearth base.

4.Center cabinet mantel on hearth base

(see Figure 11). Make sure mantel is flush against wall and centered left to right on base.

5.Use hardware provided with mantel accessory to attach mantel assembly to base (see mantel instruction sheet).

6.Attach flexible gas line to fireplace gas regulator. See Connecting to Gas Supply, page 13.

7.Check all gas connections for leaks. See

Checking Gas Connections, page 15.

8.Carefully insert fireplace into cabinet mantel (see Figure 12). Be careful not to scratch or damage hearth base or cabinet mantel (see manual instruction sheet.

Hearth

Base

Figure 11 - Installing Cabinet Mantel onto Hearth Base

Cabinet

Mantel

Hearth Base

Figure 12 - Installing Fireplace into Mantel Assembly

12

www.fmiproducts.com

119315-01D

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING:Thisappliancerequiresa45°maleflarefitting5/8"- 18 UNF (Unified National Fine Thread)inletconnectionandthe flexible gas line provided.

WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.

WARNING: Never connect natural gas fireplace to private

(non-utility)gas wells. This gas is commonly known as wellhead gas.

IMPORTANT: For natural gas, check gas line pressure before connecting fireplace to gas line. Gas line pressure must be no greater than 14" of water. If gas line pressure is higher, heater regulator damage could occur.

CAUTION:Neverconnectpropane/LP fireplace directly to the propane/LPsupply.Thisfireplace requires an external regulator

(notsupplied).Installtheexternal regulator between the fireplace and propane/LP supply.

For propane/LPunits, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between

11" and 14" of water. If you do not reduce incoming gas pressure, fireplace regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 13. Pointing the vent down protects it from freezing rain or sleet.

External Regulator

Propane/LP

Supply Tank

Vent Pointing Down

Figure 13 - External Regulator With Vent

Pointing Down

CAUTION: Use only new, black iron or steel pipe. Inter-nally-tinnedcopper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2"orgreaterdiametertoallow proper gas volume to fireplace. If pipe is too small, undue loss of volume will occur.

Installation must include an equipment shutoff valve, union and plugged 1/8" NPTtap. Locate

NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see

Figure 14, page 14).

IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves.

WARNING: Use pipe joint sealantthatisresistanttoliquid petroleum (LP) gas.

119315-01D

www.fmiproducts.com

13

INSTALLATION

Continued

We recommend that you install a sediment trap in supply line as shown in Figure 14. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trappedmatterisnotlikelytofreeze.Asediment trap traps moisture and contaminants. This keeps them from going into fireplace controls.

If sediment trap is not installed or is installed wrong, fireplace may not run properly.

Equipment Shutoff

 

Valve With 1/8" NPT

Propane/LP

Tap*

From External

 

 

Regulator (11"

 

W.C.** to 14"

 

W.C. Pressure)

Approved

Natural

Flexible Gas

From Gas Meter

Line

(5" W.C.** to

 

 

10.5" W.C.

3" Minimum

Pressure)

 

Pipe Nipple Cap Tee Joint

Sediment Trap

Figure 14 - Gas Connection

* Purchase the optional equipment shutoff valve from your dealer. See Accessories, page 34.

CONNECTING Fireplace to Gas Supply

Installation Items Needed

Phillips screwdriver

sealant (resistant to propane/LP gas, not provided)

NOTICE: Most building codes do not permit concealed gas connections. A flexible gas line is provided to allow accessibility from the fireplace (see

Figure 1, page 5). The flexible gassupplylineconnectiontothe equipmentshutoffvalveshould be accessible.

1.Route flexible gas line, included, from fireplace control to equipment shutoff valve through side or rear access holes in outer casing (see Figure 1, page 5).

2.Apply pipe joint sealant lightly to male threads of gas connector attached to flexible gas line/equipment shutoff valve

(see Figure 15).

CAUTION: Avoid damage to regulator.Holdgasregulatorwith wrenchwhenconnectingittogas piping and/or fittings (ManualControlled Models Only).

CAUTION: Avoid damage to gas control. Hold gas control with wrench when connecting it to gas piping and/or fittings(Remote-ReadyModels Only).

3.Check all gas connections for leaks. See

Checking Gas Connections.

4.Feed flexible gas line into fireplace base area while replacing branch support. Make suretheentireflexiblegaslineisinfireplace base area.

To Gas Regulator

 

(Manual-Controlled

 

Models) or Control

 

Valve (Remote-

Equipment

Ready Models)

Shutoff Valve

 

 

Propane/LP

 

To External

Flexible Gas Line

Regulator

 

from Fireplace Gas

 

Regulator Provided

 

With Fireplace

Natural

 

 

To Gas Supply

Figure 15 - Attaching Flexible Gas Line

to Equipment Shutoff Valve

14

www.fmiproducts.com

119315-01D

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

WARNING:Testallgaspiping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once.

WARNING:Neveruseanopen flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles formingshowaleak.Correctallleaks at once.

CAUTION: Make sure externalregulatorhasbeeninstalled between propane/LP supply and fireplace. See guidelines underConnecting to Gas Supply, page 13.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1.Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage heater regulator.

2.Cap off open end of gas pipe where equipment shutoff valve was connected.

3.Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

4.Check all joints of gas supply piping system.

Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Reconnect fireplace and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1.Close equipment shutoff valve (see Figure 16).

2.Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

3.Check all joints from gas meter to equipment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP (see Figures 17 or 18).

Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

4.Correct all leaks at once.

Equipment

Open

 

Shutoff Valve

 

Closed

Figure 16 - Equipment Shutoff Valve

Equipment

Gas Valve

Shutoff Valve

 

Propane/LP

 

Supply Tank

 

Figure 17 - Checking Gas Joints

(Propane/LP Only)

Equipment

Gas Regulator or

Shutoff Valve

Gas Control Valve

Gas

Meter

Figure 18 - Checking Gas Joints (Natural

Gas Only)

119315-01D

www.fmiproducts.com

15

INSTALLATION

Continued

Pressure Testing Fireplace Gas

Connections

1.Open equipment shutoff valve (see Figure

16, page 15).

2.Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

3.Make sure control knob of fireplace is in the OFF position.

4.Check all joints from equipment shutoff valve to gas regulator (Manual-ControlledModels) or to gas control valve (Remote-

Ready Models) (see Figures 17 or 18, page 15). Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Light fireplace (see Operating Fireplace, page 18). Check all other internal joints for leaks.

7.Turn off fireplace (see To Turn Off Gas to Appliance, page 20 forManual-Controlled

Models or page 21 for Remote-ReadyModels).

16

www.fmiproducts.com

119315-01D

INSTALLATION

Continued

optional Wall Mounted Thermostat - GWMT1 (Remote-ReadyModels Only)

WARNING: Read and follow installation instructions. Installation should be done by aqualifiedinstallerfamiliarwithlow-voltagewiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Disconnect jumper wire from control valve (see Figure 19).

2.Connect one terminal of 25 ft. wire to “TPTH” terminal on control valve (see Figure 19).

3.Connect remaining wire terminal to the “TH” terminal on the control valve. Make sure that wire terminals are in the positions on your unit as pictured in Figure 19.

4.Route the 25 ft. wire to a convenient location to mount your thermostat (no outside wall). IMPORTANT: The wire may be shortened but must not be lengthened.

The thermostat should be mounted 54" above the floor in a location where there is good air circulation. Avoid heat sources such as lamps, direct sunlight, fireplace or heat and air conditioning ducts.

5.Gently remove the cover of the thermostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

6.Feed the electrical wires through the rectangular slots on each side of the base (see Figure 20).

WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire hazard will occur.

7.Connect one bare wire end to each terminal (“W” and “R”) of the thermostat base (see Figure 21).

8.Install the base onto the wall with the provided screws.

9.Move the temperature adjustment back and forth to insure the bimetal is free from restrictions.

10.Replace the cover onto the base. (Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation).

11.Set switch on fireplace to Auto position.

12.Set the temperature adjustment to the desired setting. This thermostat has been electronically calibrated at the factory. No adjustment or leveling is necessary.

Control

Valve

One terminalJumper Wire of 25 ft. wire

Figure 19 - Connecting Wire Terminals

Feed wires through rectangular slots

Figure 20 - Back View of Thermostat

Base

Terminal “W”

W

Terminal “R” R

Figure 21 - Thermostat Base Terminals

“W” and “R”

119315-01D

www.fmiproducts.com

17

INSTALLATION

Continued

optional Wall SWITCH - GWMS2 (Remote-ReadyModels Only)

WARNING: Read and follow installation instructions. Installation should be done by aqualifiedinstallerfamiliarwithlow-voltagewiring procedures.

WARNING: Do not connect this switch to any electrical source! Electrical shock and/or fire hazard will occur.

1.Connect one terminal of 25 ft. wire to “TPTH” terminal on control valve (see

Figure 19, page 17).

2.Connect remaining wire terminal to the “TH” terminal on the control valve. Make sure that wire terminals are in the positions on your unit as pictured in Figure

19, page 17. If wires are not “crossed” the thermostat will not work.

3.Route the 25 ft. wire to a convenient location to mount your wall switch (no outside walls).

WARNING: Do not connect the switch to a power source. Electrical shock and/or fire hazard will occur.

IMPORTANT: The wire may be shortened but must not be lengthened.

4.Connect one bare wire end to each of the terminals of the provided wall switch.

5.Install the wall switch and cover in the wall.

INSTALLING LOG SET AND SCREEN

1.Remove log packaging material and discard packaging. Gently place log over the burner (see Figure 22). Do not allow log to contact flame. If flame contacts log, soot will be created.

2.Reattach screen by placing the notches in the screen frame over the shoulder screws and pushing down.

Shoulder Screw

Log

Screen

Figure 22 - Installing Log and Screen

Operating Fireplace

MANUAL-Controlled

Models

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.

18

www.fmiproducts.com

119315-01D

OPERATING FIREPLACE

Continued

D.Do not use this appliance if any part has been under water. Immediately call aqualifiedservicetechniciantoinspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING:Youmustoperate this fireplace with the screen in place. Make sure fireplace screen is installed before running fireplace.

NOTICE: During initial operation of new fireplace, burning logs will give off a paper-burn-ing smell. Open window to vent smell. Operate fireplace on HI position to burn off odor. This will only last a few hours.

1.STOP! Read the safety information, page 18.

2.Make sure equipment shutoff valve is fully open.

3.Turn control knob clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP!

Follow “B” in the safety information, page 18. If you don’t smell gas, go to the next step.

5.Turn control knob counterclockwise

to the PILOT position. Press in control knob for five (5) seconds (see Figure 23).

Note: Youmayberunningthisfireplace for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

6.Withcontrolknobpressedin,pressand release ignitor button (see Figure 23). This will light pilot. The pilot is attached tothefrontburner.Ifneeded,keeppressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer toTroubleshooting, page 31. Also, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, seeManual Lighting Procedure on page 20.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7. This fireplace has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again.

8.Turn control knob counterclockwise

to ON position. The burner should light.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

 

ON

 

PILOT

OFF

 

Control Knob

Piezo Ignitor

 

Figure 23 - Control Knob In The OFF

 

Position

Thermocouple

Ignitor Electrode

 

Pilot Burner

Figure 24 - Natural Gas Pilot

Ignitor

Thermocouple

Electrode

Pilot

Burner

 

Figure 25 - Propane/LP Gas Pilot

119315-01D

www.fmiproducts.com

19

OPERATING FIREPLACE

Continued

9.To turn off burner and leave pilot lit:

Turn control knob clockwise to the PILOT position.

TO TURN OFF GAS

TO APPLIANCE

1.Turn control knob clockwise to the OFF position.

2.Close equipment shutoff valve (see Figure 16, page 15)

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 19.

2.With control knob pressed in, strike match. Hold match to pilot until pilot lights.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 under Lighting Instructions, page 19.

Remote-readyModels

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must belightedbyhand.Whenlightingthepilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call aqualifiedservicetechniciantoinspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING:Youmustoperate this fireplace with the fireplace screen in place. Make sure fireplace screen is installed before running fireplace.

NOTICE: During initial operation ofnewfireplace,burninglogswill give off a paper-burningsmell. Open window to vent smell. This will only last a few hours.

WARNING: Burner will come on automatically within one minute when control valve is in the

ON position after the pilot is lit.

1.STOP! Read the safety information in column 1.

2.Make sure equipment shutoff valve is fully open.

3.Press in and turn control knob clock-

wise to the OFF position (see Figure 26).

Control Knob

Electronic Ignitor

 

 

 

 

 

 

 

 

Figure 26 - Control Knob and Ignitor

Button Location (Shown as Supplied -

No Control Options)

20

www.fmiproducts.com

119315-01D

OPERATING FIREPLACE

Continued

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP!

Follow “B” in the safety information, page 20. If you don’t smell gas, go to the next step.

5.Press in and turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 26, page 20).

Note: Youmayberunningthisfireplace for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.Withcontrolknobpressedin,pressand hold electronic ignitor button. This will light pilot. The pilot is attached to the frontoftheburner.Ifneeded,keeppressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, seeManual Lighting Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

Pilot

Ignitor

Burner

Electrode

 

Figure 27 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

 

Electrode

Figure 28 - Natural Gas Pilot

8.Slightly push in and turn control knob counterclockwise to the ON position.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

9.To turn off burner and leave pilot lit: Turn control knob clockwise to the PILOT position. If using optionalhand-heldremote, set remote switch to the OFF position to prevent draining battery.

TO TURN OFF GAS

TO APPLIANCE

1.Turn control knob clockwise to the OFF position.

2.If Using Optional Hand-HeldRemote: Set remote switch to the OFF position to prevent draining battery.

3.Close equipment shutoff valve (see Figure 16, page 15)

WARNING: Make sure remote sensorselectorswitchisintheOFF position when you are away from home for long periods of time.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 20.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 under Lighting Instructions, column 1.

optional Hand-HeldREMOTE OPERATION

Note: All remote control accessories must bepurchasedseparately(seeAccessories, page 34).Followinstructions includedwith the remote control.

Note: Refer to installation instructions included with optional remote control for remote operation.

119315-01D

www.fmiproducts.com

21

OPERATING FIREPLACE

Continued

NOTICE:Youmustlightthepilot before using the hand-heldremote control unit. SeeLighting Instructions on page 20.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Slide the remote selector switch to the REMOTE position (see Figure 29). Note: The burner may light if hand-heldremote was on when the remote selector switch was last turned off. You can now turn the burner on and off with the handheld remote control unit.

IMPORTANT:Donotleavetheselectorswitch intheREMOTEorONpositionwhenthepilot is not lit. This will drain the battery.

Selector Switch in

Control

Electronic

REMOTE Position

(Optional Hand-Held

Knob

Ignitor

Remote Control)

 

 

Figure 29 - Setting the Selector Switch and Control Knob for Hand-HeldRemote Operation

GWMT1 Wall Mounted

Thermostat (OPTIONAL)

Make sure the heater switch is on REMOTE and set the temperature adjustment on wall thermostat to the desired setting. The thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation. See installation instructions on page 17 of this manual.

GWMS2 Wall Mounted

SWITCH (OPTIONAL)

Make sure the heater switch is on RE-

MOTE. This wall switch works just like the conventional light switch. Flip the switch up for on and down for off.

Note: Make sure that this switch is not in a position to be mistaken for a light switch. This may result in the fireplace being inadvertently turned on without the proper precautions being taken. See installation instructions on page 18 of this manual.

22

www.fmiproducts.com

119315-01D

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 30 shows a correct pilot flame pattern. Figure 31 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the fireplace will shut down.

If pilot flame pattern is incorrect, as shown in Figure 31

turnfireplaceoff(seeTo Turn Off Gas toAppli-ance,page20forManual-ControlledModels or page 21 for Remote-Ready Models)

see Troubleshooting, page 31

Note: The correct pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color.

Pilot Burner

Thermocouple

Figure 30 - Correct Pilot Flame Pattern

(Propane/LP Remote-ReadyShown)

Pilot Burner

Thermocouple

BURNER FLAME PATTERN

Figure 32, shows a correct burner flame pattern. Figure 33, shows an incorrect burner flame pattern. The incorrect burner flame pattern shows sporadic, irregular flame tipping. The flame should not be dark or have an orange/reddish tinge.

Note: When using the fireplace the first time, the flame will be orange for approximately one hour until the log cures.

If burner flame pattern is incorrect, as shown in Figure 33

turnfireplaceoff(seeTo Turn Off Gas toAppli-ance,page20forManual-ControlledModels or page 21 for Remote-Ready Models)

see Troubleshooting, page 25

Figure 32 - Correct Burner Flame Pattern

Figure 33 - Incorrect Burner Flame Pattern

Figure 31 - Incorrect Pilot Flame Pattern

(Propane/LP Remote-ReadyShown)

119315-01D

www.fmiproducts.com

23

CLEANING AND MAINTENANCE

WARNING: Turn off fireplace

and let cool before cleaning.

CAUTION:Youmustkeepcontrol areas, burner and circulating airpassagewaysoffireplaceclean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, pet hair, bedding material, etc.

WARNING: Failure to keep the primary air opening(s) of theburner(s)cleanmayresultin sooting and property damage.

Burner Injector Holder and

Pilot Air Inlet Hole

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation, or as needed, and have fireplace inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI.

Your local computer store, hardware store or home center may carry compressed air in a can. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.

1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2.Inspect burner, pilot and primary air inlet holes on injector holder for dust and dirt (see Figure 34).

3.Blow air through the ports/slots and holes in the burner.

4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint or pet hair with a soft cloth or vacuum cleaner nozzle.

5.Blow air into the primary air holes on the injector holder.

6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also.Additional cleaning may be needed for proper pilot operation based on use/lack of use. A yellow tip on the pilotflamemayindicatedustanddirtinthepilot assembly. There is a small pilot air inlet hole about 2" from where the pilot flame comes out of the pilot assembly (see Figures 35 or 36, depending on model). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Ports/Slots

Injector

 

Holder

 

Primary Air

Burner

Inlet Holes

Tube

 

Figure 34 - Injector Holder On Outlet

Burner Tube

Pilot Air

Inlet Hole

Pilot Assembly

Figure 35 - Pilot Inlet Air Hole

(Propane/LP Gas)

Pilot Air

Inlet Hole

Pilot Assembly

Figure 36 - Pilot Inlet Air Hole

(Natural Gas)

24

www.fmiproducts.com

119315-01D

Cleaning and Maintenance

Continued

LOG Set

If you remove one-piecelog set for cleaning, refer toInstalling Log Set and Screen, page 18, for placement instructions.

Replace log set if broken or chipped (dimesized or larger).

CABINET

Air Passageways

Use pressurized air to clean.

Exterior

Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

Troubleshooting

WARNING: Turn off and unplug fireplace and let cool before servicing. Only a qualified service person should service and repair fireplace.

CAUTION: Never use a wire, needle or similar object to clean ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM POSSIBLE CAUSE

REMEDY

Whenignitorbuttonispressed, there is no spark at ODS/pilot

1.Ignitor electrode not connected to ignitor cable

2.Ignitor cable pinched or wet

3.Broken ignitor cable

4.Bad ignitor

5.Ignitor electrode positioned wrong

6.Ignitor electrode broken

7.Battery not installed, battery power low or battery not installed correctly

1.Reconnect ignitor cable

2.Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry

3.Replace ignitor cable

4.Replace ignitor

5.Replace pilot assembly

6.Replace pilot assembly

7.Install new alkaline battery in electronic ignitor. Verify battery is installed correctly

119315-01D

www.fmiproducts.com

25

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

 

 

Whenignitorbuttonispressed,

1.

Gas supply turned off or

1.

Turn on gas supply or open

there is spark at ODS/pilot but

 

equipment shutoff valve

 

equipment shutoff valve

no ignition

 

closed

 

 

 

2.

Control knob not in PILOT

2.

Turn control knob to PILOT

 

 

position

 

position

 

3.

Control knob not pressed

3.

Press in control knob while

 

 

in while in PILOT position

 

in PILOT position

 

4.

Air in gas lines when

4.

Continue holding down con-

 

 

installed

 

trol knob. Repeat igniting op-

 

 

 

 

eration until air is removed

 

5.

Depleted gas supply (pro-

5.

Contact local propane/LP

 

 

pane/LP only)

 

gas company

 

6.

ODS/pilot is clogged

6.

Clean ODS/pilot (see Clean-

 

 

 

 

ing and Maintenance, page

 

 

 

 

24) or replace ODS/pilot

 

 

 

 

assembly

 

7.

Gas regulator setting is not

7.

Replace gas regulator

 

 

correct

 

 

 

 

 

 

 

ODS/pilot lights but flame

1.

Control knob not fully

1.

Press in control knob fully

goes out when control knob

 

pressed in

 

 

is released

2.

Control knob not pressed

2.

After ODS/pilot lights, keep

 

 

in long enough

 

control knob pressed in 30

 

 

 

 

seconds

 

3.

Safety interlock system

3.

Wait one minute for safety

 

 

has been triggered

 

interlock system to reset.

 

 

 

 

Repeat ignition operation

 

4.

Equipment shutoff valve

4.

Fully open equipment shut-

 

 

not fully open

 

off valve

 

5.

Pilot flame not touching

5.

A) Contact local natural or

 

 

thermocouple, which al-

 

propane/LP gas company

 

 

lows thermocouple to cool,

 

 

 

 

causing pilot flame to go

 

B) Clean ODS/pilot (see

 

 

out. This problem could

 

Cleaning and Maintenance,

 

 

be caused by one or both

 

page 24) or replace ODS/

 

 

of the following:

 

pilot assembly

 

 

A) Low gas pressure

 

 

 

 

B) Dirty or partially clogged

 

 

 

 

ODS/pilot

 

 

 

6.

Thermocouple connection

6.

Hand tighten until snug,

 

 

loose at control valve

 

then tighten 1/4 turn more

 

7.

Thermocouple damaged

7.

Replace pilot assembly

 

8.

Control valve damaged

8.

Replace control valve

 

 

 

 

 

Burner does not light after

1.

Inlet gas pressure is too

1.

Contact local natural or

ODS/pilot is lit

 

low

 

propane/LP gas company

 

2.

Burner orifice is clogged

2.

Clean burner (see Cleaning

 

 

 

 

and Maintenance, page 24)

 

 

 

 

or replace burner orifice

 

3.

Thermopile leads discon-

3.

Reconnect leads (see Wir-

 

 

nected or improperly con-

 

ing Diagram, page 29)

 

 

nected (Remote-Ready

 

 

 

 

Models Only)

 

 

 

4.

Burners will not come on in

4.

Replace battery in hand-

 

 

remote position (Remote-

 

held remote and receiver

 

 

Ready Models Only)

 

 

26

www.fmiproducts.com

119315-01D

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

 

Delayed ignition of burner

1. Manifold pressure is too

1.

Contact local natural or

 

 

low

 

propane/LP gas company

 

2.

Burner orifice is clogged

2.

Clean burner (see Cleaning

 

 

 

 

and Maintenance, page 24)

 

 

 

 

or replace burner orifice

 

 

 

 

Burner backfiring during com-

1. Burner orifice is clogged or

1.

Clean burner (see Cleaning

bustion

 

damaged

 

and Maintenance, page 24)

 

 

 

 

or replace burner orifice

 

2.

Damaged burner

2.

Replace damaged burner

 

3.

Gas regulator defective

3.

Replace gas regulator

 

4.

Inlet gas pressure is too

4.

Contact local natural or

 

 

low

 

propane/LP gas company

 

 

 

 

Slight smoke or odor during

1. Residues from manufac-

1.

Problem will stop after a few

initial operation

 

turing processes and log

 

hours of operation

 

 

curing

 

 

 

2.

Not enough air

2.

Check burner for dirt and

 

 

 

 

debris. If found, clean

 

 

 

 

burner (see Cleaning and

 

 

 

 

Maintenance, page 24)

 

3.

Gas regulator defective

3.

Replace gas regulator

Fireplace produces a whistling 1. Turning control knob to HI

noise when burner is lit

position when burner is

 

cold

2.

Air in gas line

3.

Air passageways on fire-

 

place blocked

4.

Dirty or partially clogged

 

burner orifice

1.Turn control knob to LO position and let warm up for a minute

2.Operate burner until air is removed from line. Have gas line checked by local natural gas company

3.Observe minimum installation clearances (see pages 10 through 13)

4.Clean burner (see Cleaning and Maintenance, page 24) or replace burner orifice

White powder residue forming within burner box or on adjacent walls or furniture

1.When heated, vapors from furniture polish, wax, carpet cleaners, etc. may turn into white powder residue

1.Turn fireplace off when using furniture polish, wax, carpet cleaners or similar products

Moisture/condensation no-

1. Not enough combustion/

1. Refer to Air for Combustion

ticed on windows

ventilation air

and Ventilation require-

 

 

ments (page 6)

119315-01D

www.fmiproducts.com

27

TROUBLESHOOTING

Continued

WARNING: If you smell gas

Shut off gas supply.

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating fireplace where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

 

 

Remote does not function (Re-

1.

Battery is not installed.

1.

Replace batteries in receiver

mote-ReadyModels Only)

 

Battery power is low

 

and remote control

 

 

 

 

 

Fireplace produces a clicking/

1.

Metal expanding while

1.

This is normal with most

ticking noise just after burners

 

heating or contracting

 

fireplaces. If noise is ex-

are lit or shut off

 

while cooling

 

cessive, contact qualified

 

 

 

 

service person

 

 

 

 

 

Fireplace produces unwanted

1.

Fireplace burning vapors

1.

Open window to venti-

odors

 

from paint, hair spray,

 

late room. Stop using odor

 

 

glues, cleaners, chemi-

 

causing products while

 

 

cals, new carpet, etc. (See

 

fireplace is running

 

 

IMPORTANT statement

 

 

 

 

above)

 

 

 

2.

Low fuel supply (propane/

2.

Refill supply tank (propane/

 

 

LP only)

 

LP only)

 

3.

Gas leak. See Warning

3.

Locate and correct all leaks

 

 

statement at top of page

 

(see Checking Gas Con-

 

 

 

 

nections, page 15)

 

 

 

 

 

Fireplace shuts off in use (ODS

1.

Not enough fresh air is

1.

Open window and/or door

operates)

 

available

 

for ventilation

 

2.

Low line pressure

2.

Contact local natural or

 

 

 

 

propane/LP gas company

 

3.

ODS/pilot is partially

3.

Clean ODS/pilot (see

 

 

clogged

 

Cleaning and Maintenance,

 

 

 

 

page 24)

 

 

 

 

 

Gas odor even when control

1.

Gas leak. See Warning

1.

Locate and correct all leaks

knob is in OFF position

 

statement at top of page

 

(see Checking Gas Con-

 

 

 

 

nections, page 15)

 

2.

Control valve defective

2.

Replace control valve

 

 

 

 

 

Gas odor during combustion

1.

Foreign matter between

1.

Take apart gas tubing and

 

 

control valve and burner

 

remove foreign matter

 

2.

Gas leak. See Warning

2.

Locate and correct all leaks

 

 

statement at top of page

 

(see Checking Gas Con-

 

 

 

 

nections, page 15)

28

www.fmiproducts.com

119315-01D

Specifications

CGMFP

CGMFN

Rating: 10,000 Btu/Hr

Rating: 10,000 Btu/Hr

Gas Type: Propane/LP

Gas Type: Natural

Ignition: Piezo

Ignition: Piezo

• Manifold Pressure: 8.0" W.C.

• Manifold Pressure: 3" W.C.

• Inlet Gas Pressure (in. of water):

• Inlet Gas Pressure (in. of water):

 

Maximum - 14", Minimum* - 11"

 

Maximum - 10.5", Minimum* - 5"

VGMRP

VGMRN

Rating: 10,000 Btu/Hr

Rating: 10,000 Btu/Hr

Gas Type: Propane/LP

Gas Type: Natural

Ignition: Electronic Ignitor

Ignition: Electronic Ignitor

• Manifold Pressure: 8" W.C.

• Manifold Pressure: 3.0" W.C.

• Inlet Gas Pressure (in. of water):

• Inlet Gas Pressure (in. of water):

 

Maximum - 14", Minimum* - 11"

 

Maximum - 10.5", Minimum* - 5"

* For purpose of input adjustment

* For purpose of input adjustment

ALL MODELS

Dimensions (HxWxD): Fireplace (including hood and screws) - 23 3/4" x 193/4" x 87/8"

Weight: Fireplace - 30 lbs., Shipping: 33 lbs.

Wiring Diagram

(Remote-ReadyModels Only)

Jumper Wire

TPTH TH

Gas Control

TPTH TP

Red

Thermopile

White

Service Hints

When Gas Pressure Is Too Low

pilot will not stay lit

burners will have delayed ignition

fireplace will not produce specified heat

for propane/LP units, propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, contact your local natural or propane/LP gas supplier.

Technical Service

You may have further questions about installation, operation or troubleshooting. If so, contact FMI PRODUCTS, LLC’s Technical

Service Department at 1-866-328-4537.

When calling, please have your model and serial numbers of your heater ready.

You can also visit our web site at www.fmiproducts.com.

Replacement Parts

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

Parts Under Warranty

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call FMI PRODUCTS, LLC’s Technical Service Department at 1-866-328-4537.

When calling FMI PRODUCTS, LLC, have ready

your name

your address

model and serial numbers of your fireplace

how fireplace was malfunctioning

type of gas used (propane/LP or natural gas)

purchase date

Usually, we will ask you to return the part to the factory.

Parts Not Under Warranty

Contact authorized dealers of this product. If they can’t supply original replacement part(s), call FMI PRODUCTS, LLC at 1-866-328-4537for referral information.

When calling FMI PRODUCTS, LLC, have ready

model number of your fireplace

the replacement part number

119315-01D

www.fmiproducts.com

29

Illustrated Parts Breakdown

MANUAL-controlledmodels CGMFN AND CGMFP

2

39

41

13

3

41

34

 

 

 

42

 

 

 

 

 

 

11

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

37

27

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

28

 

 

41

 

26

29

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

22

 

 

 

 

 

34

 

 

 

 

 

 

 

 

 

 

 

21

 

32

 

 

 

 

 

23

31

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

43

 

 

 

 

 

 

 

 

33

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

38

 

 

15

16

18

 

 

 

34

 

 

 

 

 

 

 

 

20

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

 

 

 

 

 

24

 

 

 

 

 

17

 

 

 

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

 

15

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

35

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

40

36

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

40

 

 

30

www.fmiproducts.com

119315-01D

PARTS LIST

MANUAL-controlledmodels

This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts on page 29 of this manual.

KEY NO.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

PART NO.

DESCRIPTION

 

CGMFN

 

CGMFP

QTY

 

 

 

 

118596-01

Top Panel

 

 

1

118573-01CK

Top Trim Panel

 

 

1

118574-01

Heat Deflector

 

 

1

118576-01CK

Screen Assembly

 

 

1

118577-01CK

Access Door

 

 

1

118578-01CK

Side Panel Trim

 

 

2

**

Firebox Floor

 

 

1

**

Bottom Panel

 

 

1

**

Fireplace Wrapper

 

 

1

118941-01

Rear Brick Liner

 

 

1

118941-02

Left Brick Liner

 

 

1

118941-03

Right Brick Liner

 

 

1

118941-04

Top Liner

 

 

1

119310-01

Burner

 

 

1

103158-01

Magnetic Catch

 

 

2

118607-01

Magnetic Catch Bracket

 

 

2

100829-01

Control Valve

 

 

1

110791-02

Manual Valve Bracket

 

 

1

108480-01

Knob

 

 

1

098508-01

Valve Retainer Nut

 

 

1

099415-10

Gas Regulator NG

 

 

 

1

099415-09

Gas Regulator LP

 

 

 

1

118777-01

Outlet Tube

 

 

1

118776-01

Inlet Tube

 

 

1

118606-01

Ignitor Bracket

 

 

1

097159-04

Piezo Ignitor

 

 

1

098271-12

Ignitor Cable

 

 

1

107486-01

ODS Pilot, Propane/LP Gas

 

 

 

1

107485-01

ODS Pilot, Natural Gas

 

 

 

1

119425-03

Injector, NG

 

 

 

1

119425-01

Injector, LP

 

 

 

1

099387-08

Pilot Tube

 

 

1

112881-03

Pilot Shield

 

 

1

097809-03

Male Fitting

 

 

1

099230-02

Screw, HWH Shoulder AB 10 X .63

 

 

4

098303-02

Screw, SHWH AB 6-20x .31

 

 

2

M15823-27

Screw, PHWH B 10-16x .50

 

 

13

M12461-62

Screw, Hex SLT WSR 1/4-20x .38

 

 

1

102874-01

Knob for Access Door

 

 

1

118938-01

Log Set

 

 

1

M11084-38

Screw #8-18x 3/8

 

 

1

118575-01CK

Firebox Hood

 

 

1

101386-02

Hinge

 

 

2

098304-01

Screw, PPH AB 10-16X .38

 

 

44

101629-02

Bushing

 

 

1

101628-04

Flexible Connector

 

 

1

PARTS AVAILABLE - NOT SHOWN

901056-01

Brass Flare Fitting

1

101480-12

Jumper Wire

1

103470-01

Hardware Pack

1

101055-02

Lighting Instructions Plate

1

**Not a field replaceable part.

 

 

 

119315-01D

www.fmiproducts.com

 

 

31

ILLUSTRATED PARTS BREAKDOWN

REMOTE-READYMODELS VGMRN and VGMRP

2

39

13

34 33

11

10

 

 

 

 

 

31

 

 

 

 

 

 

12

 

 

 

37

 

 

 

 

 

 

 

30

 

 

 

 

27

 

 

 

33

 

 

 

4

26

33

29

 

 

32

16

15

33

3

9

14

28

33

38

7 34

 

41

18

24

 

Install Battery

 

 

According To

 

 

 

 

 

 

 

 

25

19

This Illustration

6

 

20

 

16

 

 

 

 

 

35

 

 

 

 

 

 

 

 

 

 

 

17

 

 

AAA

 

5

 

21

15

Battery

 

23

Negative

 

 

 

 

22

 

 

 

 

UP

 

40

 

 

 

 

 

8

 

 

 

 

32

www.fmiproducts.com

119315-01D

PARTS LIST

REMOTE-READYMODELS

This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts on page 29 of this manual.

KEY

 

 

 

NO.

PART NO.

DESCRIPTION

1

118596-01

 

Top Panel

2

118573-01CK

Top Trim Panel

3

118574-01

 

Heat Deflector

4

118576-01CK

Screen Assembly

5

118577-01CK

Access Door

6

118578-01CK

Side Panel Trim

7

**

 

Firebox Floor

8

**

 

Bottom Panel

9

**

 

Fireplace Wrapper

10

118941-01

 

Rear Brick Liner

11

118941-02

 

Left Brick Liner

12

118941-03

 

Right Brick Liner

13

118941-04

 

Top Liner

14

119310-01

 

Burner

15

103158-01

 

Magnetic Catch

16

118607-01

 

Magnetic Catch Bracket

17

103781-03

 

Gas Valve

 

 

103781-04

 

Gas Valve

18

118657-01

 

Remote Valve Bracket

19

118657-02

 

Remote Valve Bracket

20

119416-01

 

Elbow, Male 1/2 MPT x 3/8 Flare

21

098264-03

 

Connector, 3/8 MPT x 1/2 Flare

22

119318-01

 

Outlet Tube

 

 

099415-09

 

Outlet Tube

23

101628-04

 

Flexible Connector

24

118606-01

 

Ignitor Bracket

25

111435-01

 

Electronic Ignitor

26

098271-12

 

Ignitor Cable

27

103778-01

 

ODS Pilot, Propane/LP Gas

 

 

112376-01

 

ODS Pilot, Natural Gas

28

119425-01

 

Injector, LP

 

 

119425-02

 

Injector, NG

29

099387-18

 

Pilot Tube

30

112881-03

 

Pilot Shield

31

101629-02

 

Bushing

32

099230-02

 

Screw, HWH Shoulder AB 10 X .63

33

098304-01

 

Screw, PPH AB 10-16X .38

34

M15823-27

Screw, PHWH B 10-16x .50

35

M12461-62

Screw, Hex SLT WSR 1/4-20x .38

36

102874-01

 

Knob for Access Door

37

118938-01

 

Log Set

38

M11084-38

Screw #8-18x 3/8

39

118575-01CK

Firebox Hood

40

101386-02

 

Hinge

41

118658-01

 

Remote Control Bracket

 

 

 

PARTS AVAILABLE - NOT SHOWN

 

 

 

 

 

901056-01

 

Brass Flare Fitting

 

 

103470-01

 

Hardware Pack

 

 

103877-10

 

Lighting Instructions Plate

**Not a field replaceable part.

119315-01D

 

 

www.fmiproducts.com

 

VGMRN

 

VGMRP

QTY

 

 

 

 

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

2

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

2

 

 

2

 

 

 

1

 

 

 

1

 

 

1

 

 

1

 

 

1

 

 

 

1

 

 

 

1

 

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

 

1

 

 

 

1

 

 

 

1

 

 

 

1

 

 

1

 

 

1

 

 

1

 

 

4

 

 

44

 

 

13

 

 

1

 

 

1

 

 

1

 

 

1

 

 

1

 

 

2

 

 

1

 

 

1

 

 

1

 

 

1

33

Accessories

NOTICE: All accessories may notbeavailableforallfireplace models.

Purchase these fireplace accessories from your local dealer. If they can not supply these accessories, call FMI PRODUCTS, LLC at

1-866-328-4537for referral information. You can also write to the address listed on the back page of this manual.

CORNER Cabinet MANTEL WITH Full HEARTH BASE (Not Shown)

C21TP - White Painted Corner

C21TO - Light Oak Stain Corner

For all models. Space saving mantel and hearth base corner design. Complete assembly instructions included.

CABINET MANTEL and full hearth base (Not Shown) W21TP - White Painted Wall Cabinet W21TO - Light Oak Stain Wall Cabinet

For all models. Mantel features clean, classic lines. Complete assembly instructions included.

WALL-MOUNTTHERMOSTAT

SWITCH - GWMT1 (Not Shown)

For all Remote-ReadyModels.The desired comfort setting can be selected on the wall thermostat and the fireplace will automatically cycle from pilot to the heat setting selected.

WALL-MOUNTON/OFF SWITCH

GWMS2 (Not Shown)

For all Remote-ReadyModels.Allows the fireplace to be turned on and off with a wall switch.

F

ON

OFF

MODE

SET

RECEIVER AND HAND-HELD

THERMOSTAT REMOTE CONTROL

KIT - TRC

For all Remote-ReadyModels.Allows the fireplace to be operated in a manually or thermostatically controlled mode. You can turn the fireplace on and off without ever leaving the comfort of your easy chair. A wall-mount docking station is included.

ON

OFF

RECEIVER AND HAND-HELDREMOTE CONTROL KIT - Mrc

For all Remote-ReadyModels.Allows the fireplace to be turned on and off by using a hand-held remote control. A wall-mount docking station is included.

34

www.fmiproducts.com

119315-01D

NOTES

_____________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

______________________________________________________

119315-01D

www.fmiproducts.com

35

Warranty

KEEP THIS WARRANTY

Model (located on product or identification tag)______________________________

Serial No. (located on product or identification tag)___________________________

Date Purchased ___________________________

Keep receipt for warranty verification.

FMI PRODUCTS, LLC LIMITED WARRANTIES

New Products

Standard Warranty: FMIPRODUCTS,LLCwarrantsthisnewproductandanypartsthereoftobefreefromdefects in material and workmanship for a period of four (4) years from the date of first purchase from an authorized dealer provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s warnings and instructions.

For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from the date of first purchase.

Factory Reconditioned Products

Limited Warranty: FMI PRODUCTS, LLC warrants factory reconditioned products and any parts thereof to be free from defects in material and workmanship for 30 days from the date of first purchase from an authorized dealer provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s warnings and instructions.

Terms Common to All Warranties

The following terms apply to all of the above warranties:

Always specify model number and serial number when contacting the manufacturer. To make a claim under this warranty the bill of sale or other proof of purchase must be presented.

This warranty is extended only to the original retail purchaser when purchased from an authorized dealer, and only when installed by a qualified installer in accordance with all local codes and instructions furnished with this product.

This warranty covers the cost of part(s) required to restore this product to proper operating condition and an allowance for labor when provided by a FMI PRODUCTS, LLC Authorized Service Center or a provider approved by FMI PRODUCTS, LLC. Warranty parts must be obtained through authorized dealers of this product and/or FMI PRODUCTS, LLC who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.

Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the responsibility of the owner.

Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents, improper installation, lack of proper maintenance, tampering, or alteration(s).

This is FMI PRODUCTS, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty excludes any and all other warranties, express or implied, written or verbal and limits the duration of any and all implied warranties, including warranties of merchantability and fitness for a particular purpose to four (4) years on new products and 30 days on factory reconditioned products from the date of first purchase. FMI PRODUCTS, LLC makes no other warranties regarding this product.

FMI PRODUCTS, LLC’s liability is limited to the purchase price of the product, and FMI PRODUCTS, LLC shall not beliableforanyotherdamageswhatsoeverunderanycircumstancesincludingindirect,incidental,orconsequential damages.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For information about this warranty contact:

2701 S. Harbor Blvd.

Santa Ana, CA 92704

1-866-328-4537119315-01

www.fmiproducts.com Rev. D 03/10