®
Paper Shredder Destructeur de documents
Destructora de documentos 
Aktenvernichter 
Papiervernietiger
Distruggi documenti
Operating Instructions
Mode d’emploi
Instrucciones de funcionamiento
Bedienungsanleitung
Bedieningsinstructies
Istruzioni sul funzionamento
Model: |
P600C |
S60C
DM-6C
Safety Instructions
•Read and save these instructions.
•Follow all warnings and instructions marked on the product.
•Always turn off and unplug the machine before moving or cleaning.
•Operate shredder from the power source indicated on the serial label. If you are not sure of the type of power available, consult your dealer or a power company.
•Power cord should be easily accessible because it serves as the disconnect switch. If the power cord is damaged, call the number listed under Contact for Service.
•If the shredder does not come with a wastebasket, be certain the basket you select provides a stable base for the shredder. Tall or narrow baskets may be top heavy and unstable.
•Keep loose objects (jewelry, ties, long hair) away from shredder.
•CAUTION: Do not insert aerosol cleaners or lubricants into or around the machine. Some agents may combust, causing serious injury.
•Empty wastebasket frequently.
•Do not place shredder near water, over a radiator or a heat register.
•Do not rest anything on the power cord. Do not place machine where people will walk on the cord.
•The use of an extension cord is not recommended.
•Do not service this product yourself. An opened cover may expose you to dangerous voltage points or other risks and will void manufacturer’s warranty.
•Do not exceed recommended sheet capacity or usage. (See
Specifications).
•Do not shred continuous forms.
•Do not shred labels, transparencies, glossy paper, newsprint, plastic or cardboard.
•Keep out of the reach of children and pets.
•Never insert your hand or fingers into feed opening.
Installation
1.Interlock switch
As an added safety measure, this unit will not operate unless the tab on the upper right portion of the specially designed waste container has activated the interlock switch. The shredder will not operate if the interlock switch is not in the proper position or if the main unit is lifted off of the waste container. CAUTION: When moving the shredder, or after the main unit is removed to empty the waste container, always make sure that the interlock switch is properly set.
2.Be sure to use the specially designed waste container.
Operation
Prepare paper to be shredded. Do not exceed the recommended sheet capacity. (See Specifications)
1.Position paper over paper entry.
2.Slide main switch to the ON (▼) position to activate the standby mode.
3.Shredder automatically starts when paper is placed in the entry and stops when finished shredding.
Important Note: If paper is wider than the entry and you fold it to fit, the paper thickness increases and the recommended capacity may be exceeded.
Housing |
Switch |
Power Jack
Paper Entry
Wastebasket
Oil the cutters
When...
•Every second or third time you empty the basket;
•If the shredder’s cutting capacity is diminished;
•If the cutting cylinders stop with a squeak or a rubbing sound after power is removed.
How...
Use Powershred Lubricant #35250 or a suitable alternative with an extension nozzle. Alternatives can be 3 in 1 or Sewing Machine Oil. Oil must be non-flammable material and a nondegreaser! Do not use a can spray. Accelerants are combustible. Squeeze the lubricant across the full width of the cutters and then turn the machine on and run the cutting system forward for a few seconds.
Then, slide the main switch to the REVERSE (▲) position and run the cutting system for a few seconds. Repeat the procedure.
3.When shredder is positioned on basket, plug the power cord into a standard AC outlet.
If a Jam Occurs
1.Immediately return power switch to OFF (I) position.
2.Slide power switch to the REVERSE (▲) position until the jammed paper has been fully removed from the cutter.
2
Loading...