Extron electronic XPA 2001 User Manual

0 (0)
Extron electronic XPA 2001 User Manual

XTRASeries Half-Rack

Audio Power Amplifiers • Setup Guide

 

 

 

 

 

 

 

 

 

 

 

 

:

 

 

 

 

 

 

 

 

 

 

TANT complete

 

 

 

MPOR

 

forthe

and

 

 

 

 

instructions,

 

 

 

 

I

 

xtr

.com

 

 

 

 

 

.e

on

 

 

 

the

 

 

 

 

 

 

 

 

 

 

 

.

 

 

to

www

 

 

 

 

 

 

 

 

 

Go

 

,installation

connectingce

 

 

guide

 

 

 

before

 

sour

 

user

 

 

 

 

the

power

 

 

specifications

 

 

 

 

 

 

 

 

 

oduct

to

 

 

 

 

 

 

 

 

 

pr

 

 

 

 

 

 

 

 

 

 

 

WARNING: May cause serious injury. Installation and service must be performed by experienced personnel only. These products must be used with UL approved, grounded, electrical boxes.

This guide provides startup instructions for an experienced installer to set up and operate the XPA 1002 or XPA 2001 series audio power amplifiers. All references are to the XTRA Series Half-Rack User Guide which can be found on www.extron.com.

Step 1 — Powering Down Equipment

Be sure that power to the amplifier is turned off first.

NOTE: Adjust the audio level to = (full attenuation) prior to the amplifier being powered back up in step 5.

Turn off all other equipment and disconnect the power cables. Verify that the amplifier is disconnected from the power source before proceeding.

Step 2 — Mounting and Applications

For diagrams of typical application examples, see “Application Examples” in the User Guide. For further mounting instructions, see “Mounting the XTRA Series Amplifier” in the User Guide.

Step 3 — Captive Screw Audio Cable Wiring

NOTE: Control signal ground pins may be labeled as , , or “G”. Audio ground pins may be labeled as or . The wiring and function are the same, whichever way your product is labeled.

Wire the source output to the amplifier input 3.5 mm captive screw connectors as shown in the following illustration.

NOTE: The output power of the XPA 1002 and XPA 1002 Plus can be effectively doubled by using only one source channel and bridging the output. The XPA 1002 and XPA 1002 Plus output 200 watts @ 8 ohms in bridged mode (see

“Bridged Mono Output” in the User Guide for wiring instructions when bridging the XPA 1002 or XPA 1002 Plus).

 

L

Tip

Tip

 

 

Ring

Sleeve

 

 

Sleeve

 

R

 

 

R L

Tip

L

Tip

Ring

Sleeve

 

Sleeves

Tip

 

Tip

Sleeve

R

Ring

R L

Unbalanced Dual Mono Input

Balanced Dual Mono Input Unbalanced Stereo Input

Balanced Stereo Input

Do not tin the wires!

XPA 1002 Series

XPA 1002 Series

 

 

NOTE: For mono input on the XPA 2001, only the left channel needs to be wired; no jumpering to the right channel is needed. The left and right inputs of the XPA 2001 are summed internally to mono.

Step 4 — Speaker Wiring

1

2

 

Wire the speakers to the output connector of the amplifier using the included 4-pole

 

 

 

(XPA 1002 series) or 2-pole (XPA 2001-70V and XPA 2001-100V) captive screw connector as

 

 

 

shown to the right.

XPA 1002 Series

XPA 2001 Series

Step 5 — Setting the High Pass Filter (HPF)

On the XPA 2001-70V and XPA 2001-100V models, use a Tweeker to toggle the high pass filter switch between off (no filtering) and 80 Hz (default). Setting the switch to 80 Hz prevents the saturation of speaker input transformers by low frequency signals.

NOTE: The high pass filter switch may be labeled one of two ways (see the images to the right). The function is the same, whichever way your product is labeled.

HPF

HPF

80 Hz

 

80 Hz

or

 

OFF

 

Loading...
+ 1 hidden pages