User’s Manual
|
|
|
|
|
|
|
|
|
VTG 150, VTG 200 |
|
|
Extron Electronics, USA |
|
Extron Electronics, Europe |
|
Extron Electronics, Asia |
|
Extron Electronics, Japan |
Video Test Generators |
|
|
|
|
|
|
||||
|
|
1230 South Lewis Street |
|
Beeldschermweg 6C |
|
135 Joo Seng Road, #04-01 |
|
Daisan DMJ Building 6F |
|
|
|
Anaheim, CA 92805 |
|
3821 AH Amersfoort |
|
PM Industrial Building |
|
3-9-1 Kudan Minami |
68-194-01 |
|
|
USA |
|
The Netherlands |
|
Singapore 368363 |
|
Chiyoda-ku, Tokyo 102-0074 Japan |
|
www.extron.com |
|
714.491.1500 |
|
+31.33.453.4040 |
|
+65.6383.4400 |
|
+81.3.3511.7655 |
Printed in the USA |
|
Fax 714.491.1517 |
|
Fax +31.33.453.4050 |
|
Fax +65.6383.4664 |
|
Fax +81.3.3511.7656 |
||
|
|
|
|
|
© 2002 Extron Electronics. All rights reserved.
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.
Thissymbol is intended to alertthe user of thepresence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous.
Warning
Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
DiesesSymbolsolldenBenutzerdaraufaufmerksam machen, daß im Inneren des Gehäuses dieses ProduktesgefährlicheSpannungen,dienichtisoliert sind und die einen elektrischen Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand darauf treten kann oder Objekte daraufoder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/ mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.
FCC Class B Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America, |
Europe, Africa, and the Middle East: |
and Central America: |
Extron Electronics, Europe |
|
|
Extron Electronics |
Beeldschermweg 6C |
1230 South Lewis Street |
3821 AH Amersfoort |
Anaheim, CA 92805, USA |
The Netherlands |
Asia: |
Japan: |
|
Extron Electronics, Japan |
Extron Electronics, Asia |
Daisan DMJ Bldg. 6F, |
135 Joo Seng Road, #04-01 |
3-9-1 Kudan Minami |
PM Industrial Bldg. |
Chiyoda-ku, Tokyo 102-0074 |
Singapore 368363 |
Japan |
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400 (Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.
Contents
Introduction to VTG 150 & VTG 200 ..................................... |
Chapter 1 |
Introduction .............................................................................. |
1-1 |
VTG 150 Features ................................................................... |
1-2 |
VTG 200 Features ................................................................... |
1-2 |
Specifications .......................................................................... |
1-2 |
Connecting the VTG Output Cables ..................................... |
Chapter 2 |
Connecting the VTG Output Cables ........................................ |
2-1 |
15-Pin HD (VGA/XGA) Output ................................................. |
2-1 |
15-Pin Apple/Mac II (VTG 150), |
|
MacII/Quadra (VTG 200) Output ............................................. |
2-2 |
9 Pin, TTL Output .................................................................... |
2-2 |
RGB Output (BNC, Analog) ..................................................... |
2-3 |
Composite vs. Separate H & V ........................................ |
2-3 |
Sync on Red, Blue, or Green ........................................... |
2-3 |
NTSC/PAL BNC Output (VTG 200 only) ................................. |
2-3 |
13W3 Sun/SGI/IBM Output (VTG 200 only) ............................ |
2-4 |
Adapting the VTG 150 to Other Standards ............................. |
2-4 |
Monitors with a 13W3 Input Connector ............................ |
2-4 |
Connecting TTL Output to an AT&T 6300 ........................ |
2-5 |
Operating the Video Test Generator ..................................... |
Chapter 3 |
Operating the Video Test Generator ....................................... |
3-1 |
Power On ......................................................................... |
3-1 |
Timer LED ........................................................................ |
3-1 |
Exit the Instructional Menu Cycle ..................................... |
3-2 |
View the Scan Ranges ..................................................... |
3-2 |
View the Scan Rates ........................................................ |
3-2 |
Activate a Scan Rate ........................................................ |
3-2 |
Change Scan Rate ........................................................... |
3-3 |
Change Test Pattern ........................................................ |
3-3 |
Change Test Pattern Color .............................................. |
3-3 |
Auto-sequence the Test Patterns ..................................... |
3-3 |
NTSC/PAL LED (VTG 200 only) ...................................... |
3-3 |
Timer ................................................................................ |
3-3 |
Add Sync to a Video Line ................................................. |
3-4 |
Sync Output Selection ...................................................... |
3-4 |
Power Off ......................................................................... |
3-5 |
Application Information ........................................................ |
Chapter 4 |
VTG Formats ........................................................................... |
4-1 |
Video Test Patterns ................................................................. |
4-3 |
Setting Up Large Screen Projection Systems ......................... |
4-5 |
Video Setup Guide .................................................................. |
4-6 |
Monitor Applications ................................................................ |
4-7 |
Troubleshooting ....................................................................... |
4-9 |
Page i
VTG 200 RS-232 Control and Software ................................ |
Chapter 5 |
VTG 200 RS-232 Control and Connection to Computer |
......... 5-1 |
Host/VTG 200 Communications ....................................... |
5-2 |
Using the Command/Response Table ............................. |
5-2 |
Command/Response Table ..................................................... |
5-3 |
Definitions and Abbreviations .......................................... |
5-3 |
Error Code Descriptions ................................................... |
5-3 |
VTG 200 Control Program ....................................................... |
5-5 |
Installing the Software ...................................................... |
5-5 |
Using the Software ........................................................... |
5-5 |
Reference Material ............................................................ |
Appendix A |
VTG Software Updates ............................................................ |
A-1 |
Part Numbers .......................................................................... |
A-1 |
Adapters ........................................................................... |
A-1 |
Pre-cut BNC Cables ......................................................... |
A-1 |
VGA Male-Female Cables................................................ |
A-1 |
Mac/Quadra Male-Female Cables ................................... |
A-2 |
Male-to-Female Cables (Sun/SGI) ................................... |
A-2 |
VGA 15-pin HD Male to 15-pin HD Male Cables ............. |
A-2 |
Mac/Quadra 15-pin Male to 15-pin Male Cables ............. |
A-2 |
13W3 Male-to-Male Cables (Sun/SGI) ............................. |
A-2 |
All trademarks mentioned in this manual are the properties of their respective owners.
68-194-01 Rev. C
Printed in the USA
04 02
Legend of Icons
___ Important information – for example, an action or a step that must be done before proceeding.
___ A Warning – possible damage could occur.
_ A Note, a Hint, or a Tip that may be helpful.
__ Possible Electrostatic Discharge (ESD) damage could result from touching electronic components.
__ Additional information may be referenced in another section, or in another document.
Extron VTG 150 & VTG 200
User’s Manual
1Chapter One
Introduction
Introduction
VTG 150 Features
VTG 200 Features
Specifications
Page ii
Introduction
Introduction
The Extron VTG 150 and VTG 200 Video Test Generators reproduce computer video signals with patterns for testing and repairing computer monitors, LCD panels, interfaces and large screen displays. They are also used to setup and simulate computer video for system installations.
Both the VTG 150 and the VTG 200 have 16 selectable test patterns for setting and testing geometry, focus, convergence, gray scale and other parameters. After a test pattern has been selected, the color of each pattern may be changed to display in the colors white, black, red, green, blue, cyan, magenta and yellow.
The VTG 200 is field programmable through its RS-232 port. New scan rates can be added by the user as they are encountered on new equipment. The included Windowscompatible software simplifies the programming.
This user’s manual provides the information necessary to operate the VTG 150 and VTG 200 video test generators. A label on the bottom of each unit provides quick-reference operating instructions.
Introduction
VTG 150 Features
•Easy operation - When power is applied to the VTG, the LCD displays a series of instructional menus.
•Output connectors provide connection to RGB (BNC), TTL, Macintosh and VGA/XGA devices.
•Sync output can be composite H/V; separate H & V; Sync on Green; or sync on red, green, and blue.
•Automatic time-out to prevent video burn-in
•Pre-loaded scan rates - The VTG 150 has been pre-loaded with the most popular video scan rates.
•Sixteen test patterns with selectable color combination
•Upgrades and options - As new scan formats are introduced, the VTG 150 can be sent to Extron to be upgraded.
•Automatic test pattern sequencing for burn-in applications of display and video processing equipment.
VTG 200 Features
The VTG 200 Video Test Generator has all of the features of the VTG 150 listed above plus:
•13W3 output connector for Sun, SGI, IBM Power PC and NEXT type monitors
•NTSC/PAL BNC output connector
•SMPTE color bar and PLUGE test pattern for NTSC/PAL
•RS-232 connector supports VTG 200 control and field loading of scan rates (Extron or user-supplied scan rates).
•Internal power supply operates on any AC line voltage input in the 100-240VAC, 50/60Hz range.
•Field programmable and upgradeable by Extron or the user as new scan rates are introduced by computer and graphics card manufacturers
Specifications
Video
Bandwidth ..................................... |
450 MHz (-3dB) |
Video signal characteristics |
|
Dot clock ........................................ |
230 MHz |
Pixel clock accuracy .................... |
0.02 MHz |
Scan rate accuracy ....................... |
±2% |
Frequency range .......................... |
15 kHz to 127 kHz |
Rise/fall time ............................... |
<1.2 nS |
Page 1-1 |
Extron • VTG 150 & VTG 200 • User’s Manual |
Extron • VTG 150 & VTG 200 • User’s Manual |
Page 1-2 |
|
|
Introduction |
Video output |
|
|
Number/signal type |
|
|
VTG 150 ................................... |
1 RGBHV, RGBS, RGsB, RsGsBs |
|
VTG 200 ................................... |
1 RGBHV, RGBS, RGsB, RsGsBs, NTSC/PAL |
|
Connectors |
composite video |
|
|
|
|
VTG 150 ................................... |
5 BNC female, 1 15-pin HD female, 1 15-pin |
|
|
D female, 1 9-pin D female |
|
VTG 200 ................................... |
5 BNC female, 1 BNC female, 1 15-pin HD |
|
|
female, 1 |
15-pin D female, 1 13W3 D |
Rates |
female, 1 |
9-pin D female |
|
|
|
VTG 150 ................................... |
VGA-UXGA, Apple/Mac/Quadra, TTL, |
|
|
HDTV |
|
VTG 200 ................................... |
VGA-UXGA, Apple/Mac/Quadra, Sun/ |
|
|
SGI/NeXT/IBM Power PC, TTL, HDTV |
|
Maximum level ............................ |
1V p-p |
|
Impedance ..................................... |
75 ohms |
|
Return loss .................................... |
-30dB @ 5 MHz |
|
DC offset ........................................ |
±5mV maximum |
Control/remote — test generator (VTG 200 only)
Serial control port ....................... |
RS-232, 9-pin female D connector |
Baud rate and protocol .............. |
9600, 8-bit, 1 stop bit, no parity |
Serial control pin configurations |
2 = TX, 3 = RX, 5 = GND |
Program control ........................... |
Extron’s control program for Windows® |
|
Extron’s Simple Instruction Set™ – SIS™ |
|
Extron’s Advanced Instruction Set™ – |
|
AIS™ |
General
Power ............................................. |
100VAC to 240VAC, 50/60 Hz, 9 watts, |
VTG 150 ................................... |
external, auto-switchable; to 9.0VDC, 0.6 A |
VTG 200 ................................... |
internal, auto-switchable |
Temperature/humidity ............. |
Storage -40° to +158°F (-40° to +70°C) / |
|
10% to 90%, non-condensing |
|
Operating +32° to +122°F (0° to +50°C) / |
|
10% to 90%, non-condensing |
Rack mount ................................... |
No |
Enclosure type ............................. |
Metal |
Enclosure dimensions |
|
VTG 150 ................................... |
4.7" H x 4.6" W x 1.7" D |
|
11.9 cm H x 11.7 cm W x 4.3 cm D |
|
(5.5” (14 cm) H includes connectors) |
VTG 200 ................................... |
6.3" H x 9.0" W x 2.0" D |
|
16.0 cm H x 22.9 cm W x 5.1 cm D |
Product weight |
(7.0” (17.8 cm) H including connectors.) |
|
|
VTG 150 ................................... |
1.7 lbs (0.8 kg) |
VTG 200 ................................... |
3.3 lbs (1.5 kg) |
Shipping weight |
|
VTG 150 ................................... |
4 lbs (1.8 kg) |
VTG 200 ................................... |
7 lbs (3.2 kg) |
Vibration ........................................ |
ISTA/NSTA 1A in carton (International |
|
Safe Transit Association) |
Listings ........................................... |
UL, CUL |
Compliances ................................. |
CE, FCC Class B |
MTBF .............................................. |
30,000 hours |
Warranty ........................................ |
3 years parts and labor |
|
|
|
|
Specifications are subject to change without notice. |
|
|
Page 1-3 |
|
Extron • VTG 150 & VTG 200 • User’s Manual |
|
|
|
Extron VTG 150 & VTG 200
User’s Manual
2Chapter Two
Connecting the VTG
Output Cables
15-Pin HD (VGA/XGA) Output
15-PinApple/MacII(VTG150),MacII/Quadra(VTG200)Output
9 Pin, TTL Output
RGB Output (BNC, Analog)
NTSC/PAL BNC Output (VTG 200 only)
13W3 Sun/SGI/IBM Output (VTG 200 only)
Adapting the VTG 150 to Other Standards
Connecting the VTG Output Cables
Connecting the VTG Output Cables
100-240 VAC
VTG 200 ↑
VTG 150 ↓
The VTG 200 (above) provides six sets of video output connectors; the VTG 150 (at right) provides four sets. Each connector is marked for its video application.
See the table of video scan formats on page 4-1 and choose the one to be used to simulate your computer. Then connect the appropriate cables to the device to be tested. (e.g. projector, switcher, etc.)
15-Pin HD (VGA/XGA) Output
One connector is provided for the VGA/ XGA because the pin configurations are
identical. All scan rate signals go to the
VGA/XGA (15-pin HD), Apple/MacII/Quadra (15-pin) and BNC connectors. The BNC output is individually buffered, allowing devices to be connected to BNC and VGA/XGA outputs at the same time. However, because the VGA/XGA and Apple/ MacII/Quadra outputs are in parallel, they should not be connected at the same time.
_ If devices are connected to both 15-pin outputs VGA/XGA & Apple/MacII/Quadra simultaneously, the double termination will result in a loss of brightness.
The pin assignments for the 15-pin HD are as follows:
Pin 1 = Red |
Pin 8 = Blue Ground |
||
Pin 2 |
= Green |
Pin 10 |
= Ground |
Pin 3 |
= Blue |
Pin 13 = H. Sync |
|
Pin 6 |
= Red Ground |
Pin 14 |
= V. Sync |
Pin 7 |
= Green Ground |
|
|
The sync available on pins 13 and 14 is dependent on the position of the H/HV switch. With the switch in the HV (down) position, composite sync is available on pin 13. With the switch in the H (up) position, separate H and V sync is available on pins 13 and 14.
Connecting the VTG Output Cables
15-Pin Apple/Mac II (VTG 150), MacII/Quadra (VTG 200)
Output
All scan rate signals go to the VGA/ XGA (15-pin HD), Apple/MacII/
Quadra (15-pin) and BNC
connectors. The BNC output is individually buffered, allowing devices to be connected to BNC and Apple/MacII/Quadra outputs at the same time. However, because the VGA/XGA and Apple/MacII/Quadra outputs are in parallel, they should not be connected at the same time.
_ If devices are connected to both 15-pin outputs (VGA/XGA & Apple/MacII/Quadra) simultaneously, the double termination will result in a loss of brightness.
The pin assignments for the Apple/MacII/Quadra connector are as follows:
Pin 1 = Red Ground |
Pin 9 = Blue |
||
Pin 2 |
= Red |
Pin 11 |
= C/V Sync Ground |
Pin 3 = Composite Sync |
Pin 12 |
= V. Sync |
|
Pin 5 |
= Green |
Pin 13 = Blue Ground |
|
Pin 6 |
= Green Ground |
Pin 14 |
= H. Ground |
|
|
Pin 15 |
= H. Sync |
9 Pin, TTL Output
A 9 pin “D” style connector provides all TTL signal outputs. These outputs may
be selected from the TTL Scan Rates menu.
Pin 1 |
= Ground |
Pin 5 = Blue |
|
Pin 2 = Red Intensity |
Pin 6 |
= Green Intensity |
|
Pin 3 |
= Red |
Pin 7 |
= Blue Intensity |
Pin 4 |
= Green |
Pin 8 = H. Sync |
|
|
|
Pin 9 = V. Sync |
_ When running TTL rates from outputs other than the 9-pin TTL output, the test patterns may appear dim, distorted or otherwise unlike the output from the 9 pin connector. This is normal, due to the signal characteristics of TTL video signals. Thus, for exact TTL signal duplication, only use the 9 pin TTL output.
Page 2-1 |
Extron • VTG 150 & VTG 200 • User’s Manual |
Extron • VTG 150 & VTG 200 • User’s Manual |
Page 2-2 |
Connecting the VTG Output Cables
RGB Output (BNC, Analog)
The RGB BNC output provides red, green, and blue
video at 0.7 volts peak to peak and horizontal and vertical sync at TTL levels on the H/HV and V BNC connectors. Those five BNC connectors, together with the 2-position switch, can be used four ways:
•RGB with composite horizontal and vertical sync (4-cables)
•RGB with separate horizontal and vertical sync (5-cables)
•RGB with Sync on Green (3-cables)
•RGB with sync on red, green, and blue (3-cables)
Composite vs. Separate H & V
The vertical sync is provided on the BNC connector marked V. Depending on the position of the toggle switch, the H/HV connector can have either a separate horizontal sync, or a composite horizontal/vertical sync. For example: for composite sync output, put the toggle switch in the HV position and don't use the V connector. Forseparate H & V sync output, put the switch in the H position and connect cables to both the H/HV and the V connectors.
Sync on Red, Blue, or Green
Sync on Green may be removed or added for all scan formats. If normal operation of the selected scan rate is Sync On Green, that is what the VTG will output. However, the sync may be removed by following the instructions in Chapter 3.
The sync polarity (positive or negative) of the BNC H & V output is identical to that of the selected computer.
To output negative composite sync at all times (optimum for converging video projectors), place the back panel toggle switch in the HV position. All frequencies may be output on the BNC connectors.
NTSC/PAL BNC Output (VTG 200 only)
The VTG 200 NTSC/PAL BNC connector provides composite video output when an NTSC or PAL scan rate is selected.
Connecting the VTG Output Cables
13W3 Sun/SGI/IBM Output (VTG 200 only)
The pin assignments for the 13W3 connector are:
Pin A1 = Red
Pin A2 = Green
Pin A3 = Blue
Sync pin assignments vary by manufacturer as follows:
Signal |
Sun |
SGI |
IBM |
NXT |
H/HV |
5 |
3 |
5 |
A2 (SOG) |
V |
NC |
4 |
9 |
NC |
Ground |
10 |
10 |
10 |
10 |
Adapting the VTG 150 to Other Standards
For some applications, the unit
to be tested may not have connectors that match those provided on the VTG 150.
Adaptor cables can be made up
to serve this need. Following are some examples.
Monitors with a 13W3 Input Connector
When connecting a VTG 150 to a monitor that uses the 13W3 connector, use an adapter cable with the following, 4 or 5 BNC configuration:
BNC |
13W3 Connector Pin Numbers |
|||
Cable |
SUN |
SGI |
IBM |
NEXT |
Red |
A1 |
A1 |
A1 |
A1 |
Green |
A2 |
A2 |
A2 |
A2 (SOG) |
Blue |
A3 |
A3 |
A3 |
A3 |
H/HV |
5 |
3 |
5 |
NC |
V |
NC |
4 |
9 |
NC |
Ground |
10 |
10 |
10 |
10 |
Page 2-3 |
Extron • VTG 150 & VTG 200 • User’s Manual |
Extron • VTG 150 & VTG 200 • User’s Manual |
Page 2-4 |