Exmark Lazer Z S 000 Higher, Lazer Z S 312, Lazer Z S User Manual

0 (0)

LAZER Z® S-SERIES

For Serial Nos.

312,000,000 & Higher

Lazer Z (LZS) Units

Part No. 4501-199 Rev. A

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Important: The engine in this product is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code (CPRC) Section 4442 to use or operate this engine on any forest-covered, brush-covered, or grass-covered land as defined in CPRC 4126. Other states or federal areas may have similar laws.

To acquire a spark arrester for your unit, see your Engine Service Dealer.

This spark ignition system complies with the Canadian standard ICES-002. Ce système d’allumage par ètincelle de vèhicule est conforme à la norme NMB-002 du Canada.

The enclosed Engine Owner’s Manual is supplied for information regarding The U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.

Keep this engine Owner’s Manual with your unit. Should this engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered through the engine manufacturer.

Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be evident in the actual specifications of its products and the statements and descriptions contained in this publication.

©2012 Exmark Mfg. Co., Inc.

 

Contact us at www.Exmark.com.

Industrial Park Box 808

 

Printed in the USA

2

Beatrice, NE 68310

All Rights Reserved

Introduction

CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation.

This manual contains operating, maintenance, adjustment, and safety instructions for your Exmark mower.

BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY.

By following the operating, maintenance, and safety instructions, you will prolong the life of your mower, maintain its maximum efficiency, and promote safe operation.

If additional information is needed, or should you require trained mechanic service, contact your authorized Exmark equipment dealer or distributor. Exmark parts manuals are available online at http://www.exmark.com

All Exmark equipment dealers and distributors are kept informed of the latest methods of servicing and are equipped to provide prompt and efficient service in the field or at their service stations. They carry ample stock of service parts or can secure them promptly for you from the factory.

All Exmark parts are thoroughly tested and inspected before leaving the factory, however, attention is required on your part if you are to obtain the fullest measure of satisfaction and performance.

Whenever you need service, genuine Exmark parts, or additional information, contact an Authorized Service Dealer or Exmark Customer Service and have the model and serial numbers of your product ready.

Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

3

Contents

 

Introduction ...........................................................

3

Safety .....................................................................

5

Safety Alert Symbol.........................................

5

Safe Operating Practices..................................

5

Safety and Instructional Decals ......................

11

Specifications ........................................................

16

Model Numbers .............................................

16

Systems ..........................................................

16

Dimensions....................................................

18

Torque Requirements .....................................

20

Product Overview .................................................

21

Operation ..............................................................

21

Controls.........................................................

21

Pre-Start.........................................................

24

Operating Instructions ...................................

25

Transporting ..................................................

29

Maintenance ..........................................................

30

Recommended Maintenance Schedule(s) ............

30

Periodic Maintenance ........................................

31

Check Engine Oil Level..................................

31

Check Mower Blades ......................................

33

Check Safety Interlock System ........................

34

Check Rollover Protections Systems (Roll

 

Bar) Knobs.................................................

34

Check Seat Belt...............................................

35

Check for Loose Hardware .............................

35

Service Air Cleaner.........................................

35

Change Engine Oil .........................................

35

Check Hydraulic Oil Level ..............................

35

Check Tire Pressures ......................................

36

Check Condition Of Belts...............................

36

Lubricate Grease Fittings................................

36

Lubricate Deck Lift Pivot ...............................

37

Check Spark Plugs..........................................

37

Change Hydraulic System Filter and

 

Fluid ..........................................................

38

Wheel Hub - Slotted Nut Torque

 

Specification...............................................

38

Check Spark Arrester (if equipped)..................

38

Thread Locking Adhesives..............................

39

Copper-Based Anti-seize ...............................

39

Dielectric Grease............................................

39

Adjustments ......................................................

39

Deck Leveling ................................................

39

Pump Drive Belt Tension................................

41

Deck Belt Tension..........................................

41

Adjusting the Parking Brake............................

41

Electric Clutch Adjustment.............................

42

Motion Control Linkage Adjustment ..............

43

Motion Control Damper Adjustment..............

44

Motion Control Neutral Lock Pivot

 

Adjustment ................................................

45

Motion Control Handle Adjustment ...............

45

Motion Control Full Forward Tracking

 

Adjustment ................................................

45

Caster Pivot Bearings Pre-Load

 

Adjustment ................................................

46

Cleaning ............................................................

47

Clean Engine and Exhaust System

 

Area ...........................................................

47

Remove Engine Shrouds and Clean

 

Cooling Fins...............................................

47

Clean Hydro Fan Cooling Fins........................

47

Clean Debris From Machine ...........................

47

Clean Grass Build-Up Under Deck .................

47

Waste Disposal...............................................

47

Troubleshooting ....................................................

49

Schematics ............................................................

52

4

Safety

Safety

Safety Alert Symbol

This lawn mower meets or exceeds the B71.4 specifications of the American National Standards Institute in effect at the time of production.

Exmark designed and tested this lawn mower to offer reasonably safe service; however, failure to comply with the following instructions may result in personal injury.

This Safety Alert Symbol (Figure 2) is used both in this manual and on the machine to identify important safety messages which must be followed to avoid accidents.

This symbol means: ATTENTION! BECOME

ALERT! YOUR SAFETY IS INVOLVED!

Figure 2

Safety Alert Symbol

The safety alert symbol appears above information which alerts you to unsafe actions or situations and will be followed by the word DANGER,

WARNING, or CAUTION.

DANGER: White lettering / Red background. Indicates an imminently hazardous situation which, if not avoided, Will result in death or serious injury.

WARNING: Black lettering / Orange background. Indicates a potentially hazardous situation which, if not avoided, Could result in death or serious injury.

CAUTION: Black lettering / Yellow background. Indicates a potentially hazardous situation which, if not avoided, May result in minor or moderate injury.

This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

Safe Operating Practices

Training

Read the Operator’s Manual and other training material. If the operator(s) or mechanic(s) can not read English it is the owner’s responsibility to explain this material to them.

Become familiar with the safe operation of the equipment, operator controls, and safety signs.

All operators and mechanics should be trained. The owner is responsible for training the users.

Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

Only adults and mature teenagers should operate a mower, and even mature teenagers should have adult supervision. Be sure a teenager:

1.has read and understands the Operator's Manual and recognizes the risks involved;

2.is sufficiently mature to use caution; and

3.is of sufficient size and weight to operate the controls comfortably and to manage the mower without taking risks.

The owner/user can prevent and is responsible for accidents or injuries occurring to himself or herself, other people or property.

Preparation

Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by Exmark.

Wear appropriate clothing including safety glasses, substantial footwear, long trousers, and hearing protection. Do Not operate when barefoot or when wearing open sandals. Long hair, loose clothing or jewelry may get tangled in moving parts.

CAUTION

This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss through extended periods of exposure.

Wear hearing protection when operating this machine.

5

Safety

Inspect the area where the equipment is to be used and remove all rocks, toys, sticks, wires, bones, and other foreign objects which can be thrown by the machine and may cause personal injury to the operator or bystanders.

DANGER

In certain conditions gasoline is extremely flammable and vapors are explosive.

A fire or explosion from gasoline can burn you, others, and cause property damage.

Fill the fuel tank outdoors on level ground, in an open area, when the engine is cold. Wipe up any gasoline that spills.

Never refill the fuel tank or drain the machine indoors or inside an enclosed trailer.

Do Not fill the fuel tank completely full. Fill the fuel tank to the bottom of the filler neck. The empty space in the tank allows gasoline to expand. Overfilling may result in fuel leakage or damage to the engine or emission system.

Never smoke when handling gasoline, and stay away from an open flame or where gasoline fumes may be ignited by spark.

Store gasoline in an approved container and keep it out of the reach of children.

Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel when engine is running or when the engine is hot.

If fuel is spilled, Do Not attempt to start the engine. Move away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated.

Do Not operate without entire exhaust system in place and in proper working condition.

DANGER

In certain conditions during fueling, static electricity can be released causing a spark which can ignite gasoline vapors. A fire or explosion from gasoline can burn you and others and cause property damage.

Always place gasoline containers on the ground away from your vehicle before filling.

Do Not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge.

When practical, remove gas-powered equipment from the truck or trailer and refuel the equipment with its wheels on the ground.

If this is not possible, then refuel such equipment on a truck or trailer from a portable container, rather than from a gasoline dispenser nozzle.

If a gasoline dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.

WARNING

Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors has caused cancer in laboratory animals. Failure to use caution may cause serious injury or illness.

Avoid prolonged breathing of vapors.

Keep face away from nozzle and gas tank/container opening.

Keep away from eyes and skin.

Never siphon by mouth.

6

Safety

CAUTION

Fuel tank vent is located inside the roll bar tube. Removing or modifying the roll bar could result in fuel leakage and violate emissions regulations.

Do Not remove roll bar.

Do Not weld, drill, or modify roll bar in any way.

Check that the operator's presence controls, safety switches, and shields are attached and functioning properly. Do Not operate unless they are functioning properly.

Operation

WARNING

Operating engine parts, especially the muffler, become extremely hot. Severe burns can occur on contact and debris, such as leaves, grass, brush, etc. can catch fire.

Allow engine parts, especially the muffler, to cool before touching.

Remove accumulated debris from muffler and engine area.

Install and maintain in working order a spark arrester before using equipment on forest-covered, grass-covered, or brush-covered unimproved land.

WARNING

Engine exhaust contains carbon monoxide, which is an odorless deadly poison that can kill you.

Do Not run engine indoors or in a small confined area where dangerous carbon monoxide fumes can collect.

Operate only in daylight or good artificial light, keeping away from holes and hidden hazards.

Be sure all drives are in neutral and parking brake is engaged before starting engine. Use seat belts with the roll bar in the raised and locked position.

Never operate the mower with damaged guards, shields, or covers. Always have safety shields, guards, switches and other devices in place and in proper working condition.

Never mow with the discharge deflector raised, removed or altered unless there is a grass collection system or mulch kit in place and working properly.

Do Not change the engine governor setting or overspeed the engine.

Park machine on level ground. Stop engine, wait for all moving parts to stop, remove key and engage parking brake:

Before checking, cleaning or working on the mower.

After striking a foreign object or abnormal vibration occurs (inspect the mower for damage and make repairs before restarting and operating the mower).

Before clearing blockages.

Whenever you leave the mower.

Stop engine, wait for all moving parts to stop, and engage parking brake:

Before refueling.

Before dumping the grass catcher.

WARNING

Hands, feet, hair, clothing, or accessories can become entangled in rotating parts. Contact with the rotating parts can cause traumatic amputation or severe lacerations.

Do Not operate the machine without guards, shields, and safety devices in place and working properly.

Keep hands, feet, hair, jewelry, or clothing away from rotating parts.

NEVER carry passengers. DO NOT operate the mower when people, especially children, or pets are in the area.

Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions.

Stop the blades, slow down, and use caution when crossing surfaces other than grass and when transporting the mower to and from the area to be mowed.

Be aware of the mower discharge path and direct discharge away from others.

7

Safety

Do Not operate the mower under the influence of alcohol or drugs.

Use extreme care when loading or unloading the machine into a trailer or truck.

Use care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

Slope Operation

Use Extreme caution when mowing and/or turning on slopes as loss of traction and/or tip-over could occur. The operator is responsible for safe operation on slopes.

DANGER

Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Do Not mow slopes when grass is wet.

Do Not mow near drop-offs or near water.

Do Not mow slopes greater than 15 degrees.

Reduce speed and use extreme caution on slopes.

Avoid sudden turns or rapid speed changes.

Keep the roll bar in the raised and locked position and use seat belt.

See inside the back cover to determine the approximate slope angle of the area to be mowed.

Use a walk behind mower and/or a hand trimmer near drop-offs, ditches, steep banks or water. (Figure 3).

Figure 3

1.Safe Zone-Use the mower here on slopes less than 15 degrees

2.Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water.

3.Water

Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing area. Tall grass can hide obstacles.

Watch for ditches, holes, rocks, dips and rises that change the operating angle, as rough terrain could overturn the machine.

Avoid sudden starts when mowing uphill because the mower may tip backwards.

Be aware that operating on wet grass, across steep slopes or downhill may cause the mower to lose traction. Loss of traction to the drive wheels may result in sliding and a loss of braking and steering.

Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly off the slope.

Follow the manufacturer’s recommendations for wheel weights or counter weights to improve stability.

Use extreme care with grass catchers or attachments. These can change the stability of the machine and cause loss of control.

Using the Rollover Protection System (ROPS)

A Rollover Protection System (roll bar) is installed on the unit.

8

Safety

WARNING

There is no rollover protection when the roll bar is down. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Keep the roll bar in the raised and locked position and use seat belt.

Lower the roll bar only when absolutely necessary.

Do Not wear seat belt when the roll bar is down.

Drive slowly and carefully.

Raise the roll bar as soon as clearance permits.

Check carefully for overhead clearances (i.e. branches, doorways, and electrical wires) before driving under any objects and Do Not contact them.

In the event of a rollover, take the unit to an Authorized Service Dealer to have the ROPS inspected.

Maintenance and Storage

Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing.

Keep engine and engine area free from accumulation of grass, leaves, excessive grease or oil, and other debris which can accumulate in these areas. These materials can become combustible and may result in a fire.

Let engine cool before storing and Do Not store near flame or any enclosed area where open pilot lights or heat appliances are present.

Shut off fuel while storing or transporting. Do Not store fuel near flames or drain indoors.

Park machine on level ground. Never allow untrained personnel to service machine.

Use jack stands to support components when required.

Carefully release pressure from components with stored energy.

Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.

Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace damaged blades. Never straighten or weld them.

Keep hands and feet away from moving parts. If possible, Do Not make adjustments with the engine running.

Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.

DANGER

Charging or jump starting the battery may produce explosive gases. Battery gases can explode causing serious injury.

Keep sparks, flames, or cigarettes away from battery.

Ventilate when charging or using battery in an enclosed space.

Make sure venting path of battery is always open once battery is filled with acid.

Always shield eyes and face from battery.

DANGER

Battery electrolyte contains sulfuric acid, which is poisonous and can cause severe burns. Swallowing electrolyte can be fatal or if it touches skin can cause severe burns.

Wear safety glasses to shield eyes, and rubber gloves to protect skin and clothing when handling electrolyte.

Do Not swallow electrolyte.

In the event of an accident, flush with water and call a doctor immediately.

9

Safety

CAUTION

If the ignition is in the “ON” position there is potential for sparks and engagement of components. Sparks could cause an explosion or moving parts could accidentally engage causing personal injury.

Be sure ignition switch is in the “OFF” position before charging the battery.

Keep all guards, shields and all safety devices in place and in safe working condition.

Check all bolts frequently to maintain proper tightness.

Frequently check for worn or deteriorating components that could create a hazard.

WARNING

Removing standard original equipment parts and accessories may alter the warranty, traction, and safety of the machine. Failure to use original Exmark parts could cause serious injury or death. Making unauthorized changes to the engine, fuel or venting system, may violate EPA and CARB regulations.

Replace all parts including, but not limited to, tires, belts, blades, and fuel system components with original Exmark parts.

WARNING

Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Fluid accidentally injected into the skin must be

surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result.

If equipped, make sure all hydraulic fluid hoses and lines are in good condition and all hydraulic connections and fittings are tight before applying pressure to hydraulic system.

Keep body and hands away from pinhole leaks or nozzles that eject high pressure hydraulic fluid.

Use cardboard or paper, not your hands, to find hydraulic leaks.

Safely relieve all pressure in the hydraulic system by placing the motion control levers in neutral and shutting off the engine before performing any work on the hydraulic system.

For Kohler EFI (Electronic Fuel Injection) Units:

WARNING

Fuel system components are under high pressure. The use of improper components can result in system failure, gasoline leakage and possible explosion.

Use only approved fuel lines and fuel filters for high pressure systems.

10

Safety

Safety and Instructional Decals

Keep all safety signs legible. Remove all grease, dirt and debris from safety signs and instructional labels.

Replace all worn, damaged, or missing safety signs.

When replacement components are installed, be sure that current safety signs are affixed to the replaced components.

If an attachment or accessory has been installed, make sure current safety signs are visible.

New safety signs may be obtained from your authorized Exmark equipment dealer or distributor or from Exmark Mfg. Co. Inc.

Safety signs may be affixed by peeling off the backing to expose the adhesive surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.

Familiarize yourself with the following safety signs and instruction labels. They are critical to the safe operation of your Exmark commercial mower.

1-303508

1-633922

1-403005

98-5954

103-2076

11

Safety

 

 

109-7232

 

1.

Fast

3.

Neutral

2.

Slow

4.

Reverse

 

 

 

 

109-7330

107-2102

109-3148

 

 

109-8483

 

 

 

All Units Except EFI

1.

Throttle–fast

3.

Choke–on

2.

Throttle–slow

4.

Choke–off

 

 

 

 

12

Safety

109-9361

Deck Drive Belt Routing

116-0090

116-0157

1.See Operator's Manual

116-0205

116-0211

116-0752

1. Latch

2. Unlatch

 

 

13

Exmark Lazer Z S 000  Higher, Lazer Z S 312, Lazer Z S User Manual

Safety

116-1654

116-2643

116-2844

EFI Units Only

1. Throttle–fast

2. Throttle–slow

 

 

116-3303

117–2718

116-5944

Message Display

1.

Fuel

6.

Hour meter

2.

Empty

7.

PTO

3.

Half

8.

Parking brake

4.

Full

9.

Neutral

5.

Battery

10.

Operator presence

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PTO Switch Symbols

1. PTO–disengage

2. PTO–engage

 

 

14

Safety

109-7069

15

Specifications

Specifications

Model Numbers

Serial Nos: 312,000,000 and Higher

LZS651KA484; LZS651KA484CA; LZS680KC524; LZS691KA524CA; LZS740KC524; LZS740KC604; LZS740KC604CA; LZS801KA724; LZS730EKC604; LZS749EKC724

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

Engine Oil Type: Exmark 4–Cycle Premium Engine Oil

RPM: Full Speed: 3750 ±50 RPM (PTO not engaged) Idle: 1500 +100/-250 RPM

Fuel System

Capacity:

All Units Except LZS730EKC604: 12.0 gal. (45.4 L)

LZS730EKC604: 8.0 gal. (30.3 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher; containing no more than 10% methanol or ethanol.

Fuel Filter:

Kohler:

Kohler P/N 24 050 13

Kawasaki:

Kawasaki P/N 49019-7005

Kohler EFI:

Kohler P/N 25 050 42

Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

Fuel level eight segment display — right hand control panel.

Low fuel indicator light.

Electrical System

Charging System: Flywheel Alternator

Charging Capacity:

Kohler and Kawasaki: 15 amps

Kohler EFI: 20 amps

Battery Type: BCI Group U1

Recommended Minimum Battery CCA: 260 CCA

Battery Voltage: 12 Volt

Low Voltage Light — RH control panel

Polarity: Negative Ground

Fuses: All units:

25 amp main fuse

25 amp charging system fuse

10 amp PTO fuse

15 amp accessory fuse

Safety Interlock System

LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

16

Specifications

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages/Disengages parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Pedal: Foot pedal that lifts deck.

Transport Lock:

Latching position: Automatically latches at the transport position.

Unlatching position: Deck does not latch at the transport position.

Seat

Type: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, armrests, integral safety switch.

Optional seat accessories for units with standard seats:

Custom ride suspension system to enhance Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

Deluxe suspension seat with high back, (adjustable spring suspension), armrests, and integral safety switch. Adds approximately 1/2 inch (1.3 cm) to seat height.

Seat Isolation System for reduced vibration, to enhance ride of standard seat, standard seat with Custom Ride Seat Suspension or Deluxe Suspension Seat. Adds approximately 1 inch (2.5 cm) to seat height.

Mounting: Adjustable fore and aft on seat tracks.

Armrests:

Standard seat: foam padded adjustable flip-up armrests.

Suspension seat: foam padded adjustable flip-up armrests.

Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Two unitized hydrostatic transmissions: 12cc Parker axial piston pump

240cc Parker geroler motor

Hydraulic Oil Type: Exmark Premium Hydro Oil.

Hydraulic Oil Capacity: 52 oz (1.5 L) per side

Hydraulic Filter: P/N 116-0164

Speeds:

0-10 mph (16.1 km/hr) forward.

0-5.5 mph (8.9 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

Tires and Wheels

 

 

 

Drive

 

Pneumatic (Air filled)

 

 

 

 

 

Deck Size

48 & 52

 

 

60 & 72

 

 

 

 

 

Quantity

2

 

 

2

Tread

Turf Master

 

Turf Master

Size

24 x 9.50-12

 

24 x 12.00-12

 

 

 

 

 

Ply Rating

4

 

 

4

 

 

 

 

 

Pressure

13 psi (90 kPa)

 

13 psi (90 kPa)

 

 

 

 

 

 

 

 

 

 

 

 

Front Caster

 

 

 

Semi-Pneumatic

Deck Size

 

48, 52, & 60 (except

 

 

LZS740KC604 &

 

 

LZS740KC604CA)

Quantity

 

2

 

 

Tread

 

Smooth

Size

 

13 x 5.00-6

 

 

 

 

 

Ply Rating

 

4

 

 

 

 

 

 

 

Pressure

 

N/A

 

 

 

 

 

 

 

 

 

Front Caster

 

 

 

Semi-Pneumatic

Deck Size

 

72, LZS740KC604 &

 

 

LZS740KC604CA

Quantity

 

2

 

 

Tread

 

Smooth

 

 

 

 

 

17

Specifications

Size

13 x 6.50-6

 

 

Ply Rating

4

 

 

Pressure

N/A

Cutting Deck

Cutting Width:

48 inch Deck: (121.9 cm)

52 inch Deck: (132.1 cm)

60 inch Deck: (152.4 cm)

72 inch Deck: (182.9 cm)

Discharge: Side

Blade Size: (3 ea.)

48 inch Deck: 16.25 inches (41.3 cm)

52 inch Deck: 18.00 inches (45.7 cm)

60 inch Deck: 20.50 inches (52.1 cm)

72 inch Deck: 24.50 inches (62.2 cm)

Blade Spindles: Solid steel spindles with 1.00 inch (25 mm) I.D. bearings.

Deck Drive: Electric clutch:

48 and 52 inch Decks: “B” Section belt with self-tensioning idler.

60 and 72 inch Decks: 5V Section belt with self-tensioning idler.

Deck:

Full floating deck is attached to out-front support frame. Anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

48 inch Deck: 3 anti-scalp rollers

52 inch Deck: 3 anti-scalp rollers

60 inch Deck: 4 anti-scalp rollers

72 inch Deck: 6 anti-scalp rollers

Deck Depth:

48 inch Deck: 5.5 inches (14 cm)

52 inch Deck: 5.5 inches (14 cm)

60 inch Deck: 5.5 inches (14 cm)

72 inch Deck: 5.5 inches (14 cm)

Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting height from 1 inch (2.5 cm) to 5 1/2 inches (14 cm) in 1/4 inch (6.4 mm) increments.

Mulching Kit: Optional.

Dimensions

Overall Width:

 

48 inch Deck

52 inch Deck

Without Deck

45.7

inches

45.7

inches

 

(116.1 cm)

(116.1 cm)

Deflector Up

51.8

inches

56.3

inches

 

(131.6 cm)

(143.0 cm)

Deflector Down

59.6

inches

64.8

inches

 

(151.4 cm)

(164.6 cm)

 

60 inch Deck

72 inch Deck

Without Deck

53.0

inches

59.1

inches

 

(134.6 cm)

(150.1 cm)

Deflector Up

62.5

inches

73.5

inches

 

(158.8 cm)

(186.7 cm)

Deflector Down

72.8

inches

84.9

inches

 

(184.9 cm)

(215.6 cm)

Overall Length:

 

48 inch Deck

52 inch Deck

Roll Bar - Up

79.2

inches

79.2 inches

 

(201.2 cm)

(201.2 cm)

Roll Bar - Down

80.9

inches

80.9 inches

 

(205.5 cm)

(205.5 cm)

 

60 inch Deck

72 inch Deck

Roll Bar - Up

83.1

inches

86.1

inches

 

(211.1 cm)

(218.7 cm)

Roll Bar - Down

84.8

inches

87.8

inches

 

(215.4 cm)

(223.0 cm)

Overall Height:

Roll Bar - Up

Roll Bar - Down

70.5 inches (179.1 cm)

46.8 inches (118.9 cm)

 

 

18

Loading...
+ 42 hidden pages