EVGA UV Plus+ 100-U2-UV19 User Manual

Size:
417.45 Kb
Download

®

A USB VGA Display Port

Quick Install Guide

Supports UV 12, UV 16 and UV 19

Introduction

EVGA’s UV Plus+ gives you the ability to use multiple displays by utilizing a USB 2.0 port on your laptop or PC. Each monitor will need either a UV 12, UV 16 or UV 19. Up to 6 UV Plus+ devices can be used at the same time allowing multiple displays through CRT and LCD monitors, or a Projector. With the ability to Mirror or Extend your desktop up, down, left, or right, EVGA’s UV Plus+ gives you full freedom to move about your virtual work space.

System Requirements:

• An available USB 2.0 port

 

• Windows® 2000, XP32-Bit,Vista or 7

 

CD-ROMorDVD-ROMif using the provided installation CD

 

• 30 MB of free disk space

 

• 1.2 GHz or higher processor

UV 12

• 512 MB of system memory (1 GB or more is recommended)

 

Package Contents:

Your EVGA UV Plus+ device will have the following optional items included in this package:

1 x DVI to VGA Adapter

1 x USB Cable

1 x Installation CD for Drivers and Software

1 x Travel Case

UVPlus+ Supports:

Windows Aero 32-BitColor Depth

Widescreen Aspect Ratio Ability to Clone or Extend

VGA, DVI, and FPI Display Connections High-DefinitionDisplays

UV 16

UV 19

The Following Resolutions

 

are Supported:

DVI connection

Resolutions may vary depending on your displays capabilities.

800x600, 1024x768, 1280x768, 1366x768, 1280x1024, 1440x900, 1400x1050

Supported on UV 12, UV 16, and UV 19

1680x1050, 1600x1200

Supported by UV 16 and UV 19 models only

1920x1200, 2048x1152

Supported by UV 19 model only

Hardware and Driver Setup:

DVI to VGA Adapter

1 – Power on your Laptop or your monitor and PC to begin the installation. 2 – Once in Windows, install the UV Plus+ drivers from the provided

installation CD. After the installation process has finished reboot your computer.

3 – Attach your monitor’s DVI connector to UV Plus+ (a DVI to VGA connector is provided if needed)

4 – Plug in the provided USB cable to UV Plus+ and the other end to your Notebook or PC’s USB port. The UV Plus+ software will now detect your attached display.

5 – Right-clickthe EVGA icon in the Windows System Tray to configure how the attached monitor should display.

A DVI to VGA Adapter is provided to allow a VGA connection to the UV Plus+ DVI connection. A USB Extension cable is also provided to allow for optimum placement of your UV Plus+.

FAQ:

Question: Will the UV Plus+ attached monitor render full 3D hardware rendered graphics when in Mirror or Extended Modes?

Answer: Yes, full 3D hardware rendered graphics can be displayed while in Mirror or Extended Modes, however running in such a configuration is limited as the application in use may become slower or not as responsive.

Question: Discoloration and constant flickering occurs through the UV Plus+ attached monitor.

Answer: Check that your monitor’s cable is properly attached and check for loose or faulty cables. If the problem continues, please contact EVGA Support at(888)-880-EVGA(3842)

Question: Why do I experience lag and delay when playing a 3D hardware accelerated game in either Mirrored or Extended mode?

Answer: USB 2.0 is limited to a 480Mbps transfer speed and because of this limitation only so much data can pass through at one time. This causes a delay that can both be seen and felt when playing a game when using the UV Plus+ device.

Question: How many monitors are supported when using UV Plus+?

Answer: The maximum amount of monitors supported is 6. Note that due to current driver limitations, only a maximum of 4 monitors can be used with an NVIDIA® based graphics card.

Question: How can I stay updated with the latest UV Plus+ software releases?

Answer: The UV Plus+ software that installs on to your computer has a built in Auto Update feature which will automatically check for any updates and then prompt you accordingly. You can right click the UV Plus+ icon in the Windows System Tray and select Updates to either configure how your computer updates or to manually check for an update.

Question: How do I uninstall UV Plus+ software?

Answer: In Vista/7 click Start Control Panel Uninstall a program Select EVGA UV Plus+ and select Uninstall. In XP or 2000 click Start Settings Control Panel Add or Remove ProgramsSelect EVGA UV Plus+ and select Uninstall.

Question: Why does my UV Plus+ attached monitor not display anything when my computer is booting up or in a DOS based environment?

Answer: UV Plus+ will only activate in a Windows based environment. Signal will be passed to your UV Plus+ attached monitor when the UV Plus+ software has fully loaded as part of the Windows startup process.