User Manual
ECOR264-4F1/ECOR264-4D1
ECOR264-8F1/ECOR264-8D1
E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N
ECOR264-4F1/ ECOR264-4D1
ECOR264-8F1/ ECOR264-8D1
Instruction Manual
2009 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation.
Release Date: Nov. 2009
QuickTime is a registered trademark of the Apple Computer, Inc. Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation. D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.
Safety Precautions
Refer all work related to the installation of this product to qualified service personnel or system installers.
Do not block the ventilation opening or slots on the cover.
Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. Handle the appliance with care. Do not strike or shake, as this may damage the appliance.
Do not expose the appliance to water or moisture, not try to operate it in wet areas. Do take immediate action if the appliance becomes wet. Turn the power off and refer servicing to qualified service personnel. Moisture may damage the appliance and also cause electric shock.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.
Do not overload outlets and extension cords as this may result in a risk of fire or electric shock.
Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperature within indoor type DVR for 0°C~40°C (32°F~104°F) and at relative humidity between 20%~80%. The input power source for this device is 100~240VAC.
Read Instructions
All the safety and operating instructions should be read before the unit is operated.
Retain Instructions
The safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the unit and in the operating instructions should be adhered to.
Follow Instructions
All operating and use instructions should be followed.
Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning
ii
Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Water and Moisture
Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is classified as a wet location.
Servicing
Do not attempt to service this unit by yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, playing particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
Object and Liquid Entry
Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.
ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in this case, the user may be urged to take adequate measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate this equipment.
iii
WEEE
This Product is RoHS compliant.
The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products. Therefore, all specifications are subject to change without prior notice. Manufacturer is not responsible for misprints or typographical errors.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
iv
TABLE OF CONTENTS
1 |
PRODUCT OVERVIEW ..................................................................................................... |
1 |
||
1.1 |
|
FEATURES ....................................................................................................................... |
1 |
|
1.2 |
|
PACKAGE CONTENTS................................................................................................... |
2 |
|
1.3 |
|
SPECIFICATIONS ........................................................................................................... |
3 |
|
1.4 |
|
FRONT PANEL ................................................................................................................ |
4 |
|
1.5 |
|
REAR PANEL................................................................................................................... |
6 |
|
1.6 |
|
VIDEO INPUTS/OUTPUTS INSTALLATION ............................................................... |
7 |
|
1.7 |
|
AUDIO INSTALLATION ................................................................................................ |
7 |
|
1.8 |
|
ALARM CONTACTS INSTALLATION ......................................................................... |
7 |
|
1.8.1 |
|
Alarm Input Contacts .............................................................................................................................. |
8 |
|
1.8.2 |
|
Alarm Output Relay................................................................................................................................. |
8 |
|
1.9 |
RS-485 KEYBOARD / PTZ INSTALLATION........................................................................... |
8 |
||
1.9.1 |
General RS-485 bus installation ............................................................................................................. |
8 |
||
1.9.2 |
RS-485 socket pin assignment ............................................................................................................... |
10 |
||
1.9.3 |
EKB-500 connection with network patch cable..................................................................................... |
10 |
||
1.9.4 |
EKB-500 connection to several DVRs................................................................................................... |
10 |
||
1.9.5 |
|
Speed Dome Installation ....................................................................................................................... |
10 |
|
1.10 |
|
USB-MOUSE INSTALLATION.......................................................................................... |
11 |
|
1.11 |
|
NETWORK CONNECTION........................................................................................ |
11 |
|
1.11.1 |
Direct PC Connection through Crossover Network Cable ................................................................... |
11 |
||
1.11.2 |
Network Connection through Patch Cable............................................................................................ |
12 |
||
1.12 |
|
FINAL INSTALL PROCESS ....................................................................................... |
12 |
|
2 MOUSE AND FRONT PANEL OPERATION ............................................................... |
13 |
||
2.1 |
|
GENERAL USB MOUSE OPERATION ....................................................................... |
13 |
2.1.1 How to select a channel / Enable audio ................................................................................................ |
13 |
||
2.1.2 |
OSD Root Menu .................................................................................................................................... |
13 |
|
2.1.3 Operation in the Configuration Menus ................................................................................................. |
13 |
||
2.1.4 |
Field Input Options ............................................................................................................................... |
14 |
|
2.2 |
|
GENERAL FRONT PANEL OPERATION ............................................................................... |
16 |
2.2.1 How to select a channel / Enable audio ....................................................................................................... |
16 |
||
2.2.2 OSD Root Menu ........................................................................................................................................... |
16 |
||
2.2.3 Front Panel Key Review............................................................................................................................... |
16 |
||
2.2.4 Operation in Configuration Menu......................................................................................................... |
16 |
||
2.2.5 |
Field Input Options ............................................................................................................................... |
17 |
|
3. |
GENERAL DVR OPERATIONS...................................................................................... |
19 |
|
3.1 |
|
RECORD ......................................................................................................................... |
19 |
3.2 |
|
LOGIN............................................................................................................................. |
19 |
3.3 |
|
SELECT CAMERA OPERATION................................................................................. |
20 |
3.5 |
|
PLAYBACK.................................................................................................................... |
20 |
3.6 |
|
PTZ .................................................................................................................................. |
22 |
v
3.6.1 |
General PTZ control (if PTZ cameras are installed) |
........................................................................22 |
||
3.6.2 |
Express Control of PTZ ......................................................................................................................... |
23 |
||
3.7 |
|
LAYOUT......................................................................................................................... |
25 |
|
3.7.1 |
Bring to full screen mode ...................................................................................................................... |
25 |
||
3.8 |
|
CHANNEL SWITCHING ............................................................................................... |
25 |
|
3.9 |
|
DISPLAY ........................................................................................................................ |
26 |
|
3.10 |
|
SEQUENCE.................................................................................................................. |
26 |
|
3.11 |
|
ZOOM........................................................................................................................... |
26 |
|
3.12 |
|
SEARCH....................................................................................................................... |
27 |
|
3.12.1 |
Time Search........................................................................................................................................... |
28 |
||
3.12.2 |
Event Search.......................................................................................................................................... |
29 |
||
3.13 |
|
COPY............................................................................................................................ |
30 |
|
3.14 |
|
LOGOUT ...................................................................................................................... |
31 |
|
4 |
DVR CONFIGURATION .................................................................................................. |
32 |
||
4.1 |
|
CONFIGURATION MENU............................................................................................ |
32 |
|
4.2 |
|
EXPRESS ........................................................................................................................ |
32 |
|
4.3 |
|
CAMERA SETTING ...................................................................................................... |
35 |
|
4.3.1 |
|
Basic Setting .......................................................................................................................................... |
35 |
|
4.3.2 |
|
Video Adjust .......................................................................................................................................... |
37 |
|
4.3.3 |
|
Motion ................................................................................................................................................... |
38 |
|
4.3.4 |
|
Video Loss ............................................................................................................................................. |
41 |
|
4.4 |
RECORD & PLAY SETTING........................................................................................ |
42 |
||
4.4.1 |
|
Record ................................................................................................................................................... |
42 |
|
4.4.2 |
|
Built-in Calculator ................................................................................................................................ |
43 |
|
4.4.3 |
|
Play ....................................................................................................................................................... |
44 |
|
4.5 |
ALARM & EVENT SETTING ....................................................................................... |
45 |
||
4.5.1 |
|
Alarm..................................................................................................................................................... |
45 |
|
4.5.2 |
|
Event...................................................................................................................................................... |
47 |
|
4.5.3 |
|
Schedule Setting .................................................................................................................................... |
54 |
|
4.5.4 |
|
Express Setup ........................................................................................................................................ |
54 |
|
4.5.5 |
|
Holidays ................................................................................................................................................ |
55 |
|
4.5.6 |
|
Schedule ................................................................................................................................................ |
56 |
|
4.5.7 |
|
Alarm Action ......................................................................................................................................... |
61 |
|
4.6 |
|
NETWORK SETTING.................................................................................................... |
65 |
|
4.6.1 |
|
LAN ....................................................................................................................................................... |
65 |
|
4.6.2 |
|
EMAIL ................................................................................................................................................... |
67 |
|
4.6.3 |
|
DDNS .................................................................................................................................................... |
68 |
|
4.6.4 |
|
Alarm Server ......................................................................................................................................... |
70 |
|
4.7 |
|
DISK INFORMATION .......................................................................................................... |
71 |
|
4.7.1 |
|
Disk ....................................................................................................................................................... |
71 |
|
4.8 |
|
DISPLAY SETTING....................................................................................................... |
72 |
|
4.8.1 |
|
Monitor OSD ......................................................................................................................................... |
72 |
|
4.8.2 |
|
Main M/T SEQ ...................................................................................................................................... |
73 |
|
4.9 |
|
SYSTEM SETTING........................................................................................................ |
74 |
|
4.9.1 |
|
Date/Time .............................................................................................................................................. |
74 |
|
4.9.2 |
|
Daylight Saving ..................................................................................................................................... |
75 |
|
4.9.3 |
|
User ....................................................................................................................................................... |
76 |
|
4.9.4 |
|
I/O Control ............................................................................................................................................ |
79 |
|
vi
|
4.9.5 |
|
Misc. ...................................................................................................................................................... |
80 |
|
4.10 |
|
INFORMATION........................................................................................................... |
81 |
|
4.10.1 |
System.................................................................................................................................................... |
81 |
|
|
4.10.2 |
Log......................................................................................................................................................... |
82 |
|
5 |
NETWORKING OVERVIEW .......................................................................................... |
84 |
||
|
5.1 |
INTRODUCTION TO TCP/IP ............................................................................................... |
84 |
|
|
5.2 |
SUBNET MASKS ................................................................................................................ |
84 |
|
|
5.3 |
GATEWAY ADDRESS ......................................................................................................... |
84 |
|
|
5.4 |
VIRTUAL PORTS................................................................................................................ |
85 |
|
|
5.5 |
PRE-INSTALLATION .......................................................................................................... |
85 |
|
|
5.6 |
WHAT IS YOUR NETWORK SETUP?.................................................................................... |
86 |
|
|
5.7 |
SIMPLE ONE TO ONE CONNECTION ................................................................................... |
87 |
|
|
5.8 |
DIRECT HIGH SPEED MODEM CONNECTION ..................................................................... |
92 |
|
|
5.9 |
ROUTER OR LAN CONNECTION ........................................................................................ |
94 |
|
6 REMOTE OPERATION FROM BROWSER...................................................................... |
97 |
|||
|
6.1 CONNECTING TO ECOR264-4/ECOR264-8 ................................................................... |
97 |
||
|
6.2 |
BROWSER SECURITY SETTING .................................................................................... |
98 |
|
|
6.2.1 |
|
Installing ActiveX controls .................................................................................................................... |
98 |
|
6.2.2 |
|
Enabling ActiveX Controls .................................................................................................................. |
101 |
|
6.3 |
REMOTE LIVE VIEW ................................................................................................. |
104 |
|
|
6.4 |
REMOTE PLAYBACK ................................................................................................ |
105 |
|
7 |
EVERFOCUS DDNS SETUP .......................................................................................... |
106 |
||
8 LINKSYS & D-LINK PORT FORWARDING ............................................................. |
108 |
|||
|
8.2 |
TYPICAL LINKSYS PORT FORWARDING ............................................................. |
108 |
|
|
8.3 |
TYPICAL D-LINK PORT FORWARDING ................................................................ |
110 |
|
9 |
TROUBLESHOOTING ................................................................................................... |
113 |
||
APPENDIX A: TIMING OF ALARM MODES.................................................................... |
114 |
|||
APPENDIX B: EXPRESS SETUP RECORDING VALUE SELECTION RULES .......... |
117 |
|||
APPENDIX C: REMOTE CONTROL................................................................................... |
119 |
|||
vii
Chapter
1
1 PRODUCT OVERVIEW
This new EverFocus digital video recorder is based on H.264 compression technology, resulting in increased recording capacity and improved network image transmission speed while retaining high image quality. Comprehensive features and extended event recording settings enable the almost universal application of this DVR. The ECOR264-4/ECOR264-8 DVR permits multiple control inputs. These inputs include mouse control, front panel control, IR remote control and EverFocus keyboard (EKB500) control. Mouse control employs a simple Graphical User Interface (GUI), offering experienced PC users the similarity of interactive command of a computer-controlled device. With the GUI, users can command specific actions on the ECOR264-4/ECOR264-8 DVR through graphical icons and visual indicators. Simply point, click and drag the playback bar on the screen to playback your recordings in any time slot. All GUI functions can be operated via the front panel buttons or mouse. Hop on the Express Lane! The ECOR264- 4/ECOR264-8 DVR is engineered for express operations. Setup, copy, search and playback recordings in seconds with a simple “point and click” on the command icons.
1.1 FEATURES
∙H.264 Compression format
∙Pentaplex Operation (Simultaneous live, recording, playback, archiving and remote viewing)
∙User friendly GUI with graphical icons and visual indicators
∙Free EverFocus DDNS Service
∙Multiple Control Inputs: mouse/front panel/remote control/keyboard
∙Built-in DVR calculator for fast recording estimation
∙Express Setup: Menu option allows quick & easy installation
∙Flexible alarm input tripper response scheduling
∙Remote configuration support from built-in web interface
∙Audio recording capabilities
∙Supports 1 internal SATA HDD
∙Built-in DVD burner(Optional – “D” model)
∙1 USB 2.0 port on front panel for video archive
∙1 USB 1.0 port on rear panel for mouse control
∙Multi-language support
1
1.2 PACKAGE CONTENTS
Digital Video Recorder x1
User Manual x 1
AC Adapter and Power Cord x1
Mouse x 1
2
1.3 SPECIFICATIONS
Number of Channels |
4 |
|
8 |
|
|
|
|
Compression Format |
|
H.264 |
|
Recording & Playback |
120 NTSC / 100 PAL (CIF) |
|
120 NTSC / 100 PAL (CIF) |
60 NTSC / 50 PAL (Half D1) |
|
60 NTSC / 50 PAL (Half D1) |
|
Rate/Resolution |
|
||
30 NTSC / 25 PAL (D1) |
|
30 NTSC / 25 PAL (D1) |
|
|
|
||
|
|
|
|
Pentaplex Operation |
Simultaneous Live, Recording, Playback, Archive and Remote Viewing |
||
Video Inputs |
4 BNC Composite |
|
8 BNC Composite |
|
|
|
|
Main Monitor Outputs |
1 BNC Composite, 1 VGA |
||
|
|
||
Audio Input/Output |
1 Input / 1 Output 10K9/500mV P-P |
||
Recording Mode |
Manual, Schedule and Event |
||
|
|
||
Playback Search |
By Date/Time and Event |
||
|
|
|
|
Alarm In |
4 Inputs |
|
8 Inputs |
Alarm Out |
1 Alarm Output (Form “C”) / 3A/125VAC/30VDC |
||
|
|
|
|
Video Pause |
|
Yes |
|
|
|
|
|
Video Loss Detection |
|
Yes |
|
Motion Detection |
|
Yes |
|
|
|
|
|
Event Log |
|
Yes |
|
|
|
|
|
Watch Dog Timer |
|
Yes |
|
Internal HDD |
|
1 SATA |
|
|
|
||
Built-in DVD Burner |
Slim Type DVD Burner(Optional “D” Model) |
||
|
|
||
User Interface |
GUI(Graphical User Interface) |
||
OS |
Embedded Linux |
||
|
|
||
Network/Protocol |
10/100Mbps Ethernet; TCP-IP / DHCP/ PPPoE / Everfocus DDNS |
||
|
|
||
USB |
1 USB 2.0 on Front Panel/1 USB 1.0 on Rear Panel |
||
Schedule Setting |
Supports Express and Advanced Schedule Setting |
||
|
|
||
User Access |
3 Levels of User Access Provided |
||
|
|
||
RS-485 |
Terminal connector |
||
Power Source |
12VDC/ 2 amps from 100/240VAC adapter provided |
||
|
|
||
Dimensions (L x W x H) |
320 x 208.9 x 54.3 mm / 12.6" x 8.2" x 2.1" |
||
|
|
||
Temperature |
0°C~40°C / 32°F~104°F (20~80% humidity) |
||
Supported PTZ Protocols |
EverFocus, Pelco D, Pelco P, Samsung, Transparent |
||
|
|
||
Remote Control |
Multifunction IR included |
||
|
|
||
Keyboard Support |
EKB500 via RS-485 |
||
3
1.4 FRONT PANEL
Your primary interaction with your new DVR will be through the Front Panel buttons and their corresponding buttons on the included Remote Control. Take a moment to learn where the keys are as the remainder of the manual will refer to them often.
Figure 1-1 Front Panel
1)IR Receiver: Receiver for IR remote control
2)Live: Press this key to show live view. Press to exit from playback mode.
3)View: Press this key to switch between 4x, PiP (Picture In Picture), and full screen and
9x. Examples of four different views are listed below:
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4x |
|
PiP |
Full screen |
9x |
|||||||
Note1: PIP display is not available in playback mode.
Note2: 9-screen display available in 8 Channel model only.
4)SEQ: Press this key to enter the auto sequential switching mode. The sequence dwell
time can be set in “Display Setting” tab of the Menu. For more detail about SEQ, please see “Section 4.8.2 Display Setting-Main M/T SEQ”.
5)SEARCH: Press this key to enter Search Menu. For more detail about the Search function,
please see “Section 3.12 Search ”.
4
6)◄◄/◄I: Fast reverse playback or step reverse playback depending on playback mode.
7)◄/ I I: Reverse playback or pause
8)►/ I I: Forward playback or pause
9)►►/I►: Fast Forward playback or step forward playback depending on playback mode.
10)DVD+RW: DVD+RW burner (D models only)
11)POWER LED: This LED ON indicates Power on.
12)ALARM LED: This LED ON indicates Alarm active.
13)HDD LED: This LED ON indicates HDD active.
14)Net LED: This LED ON indicates Network active.
15~18) Channel keys 1~4 (1~8): Press channel key (CH1~CH4) / (CH1~CH8) to display that channel in full screen view.
19)MENU: Press this key to enter/exit MAIN SETUP MENU.
20)COPY: Press this key to enter Copy Menu. For more detail about Copy function, please
see “Section 3.13 Copy”.
21)ENTER/ ARROW keys: Instead of or in combination with a mouse, you can use these keys to
change the Menu settings.
22)USB 2.0 port: For connecting USB-Flash-Drive to copy/archive video or for firmware upgrades.
5
1.5 REAR PANEL
During initial setup you will be connecting your DVR to multiple input and output devices. This is done through the rear panel.
○ ○ |
○ |
○ |
○ |
○ |
○ |
|
3 |
5 |
7 |
8 |
9 |
10 |
11 |
○1 ○2 ○4 ○6
Figure 1-2 Rear Panel
○1 POWER: Plug the DC 12V power source provided into the power socket.
○2 Alarm In: Connect up to 4 alarm inputs, selectable between N.O./N.C. contacts or can accept TTL/CMOS signal polarity.
○3 Alarm Out: N.C or N.O type alarm out (form “C”).
○4 RS485 socket: For remote control via RS-485 keyboards and telemetry control for attached PTZ devices
○5 Audio In: Connect a line level audio mixer output/source to the audio input connection.
○6 Audio Out: Connect the input of a line level audio amplifier to the audio output connection.
○7 Video In: Connect camera’s video output or other composite video source to the video input connection.
○8 Video Out: Main monitor - connect a CCTV monitor to the video output connection.
○9 VGA: Main monitor - connect a VGA monitor to the VGA output connection. VGA resolution is 1024x768.
○10 USB 1.0: USB port recommended for connecting the USB mouse.
6
RJ-45 network connection 10/100Mb/s Ethernet. There are two LEDs on the LAN jack; Green LED means network is connected, amber LED flickers when data is being exchanged.
1.6 VIDEO INPUTS/OUTPUTS INSTALLATION
Camera and CCTV monitor must use 75 Ohm video cable (e.g. RG-59, RG-6, RG-11) with BNC connectors.
To avoid impedance mismatch and undesired loss/reflections, 50 Ohm coax cable (e.g. RG-58), antenna cable and other types of coaxial cable are not compatible.
All connected video sources must provide a 1 Vpp NTSC or PAL standard video signal.
When converting transmission lines (twisted pair, fiber optics, radio) to the video inputs, be sure to verify accurate receiver calibration and signal levels.
ATTENTION: In order for the system to auto-detect the appropriate video format (NTSC or PAL), make sure that there is a video signal on video input 1 upon power-up.
1.7 AUDIO INSTALLATION
This DVR provides 1 audio input and 1 audio output.
ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone amplifier is required).
The installation must be done with audio coax cable and RCA plugs.
AUDIO RECORDING FUNCTIONALITY:
Audio recording is activated / deactivated in the Camera Menu for Camera #1. Please check and always comply with local laws and regulations when using audio recording.
The audio channel is always recorded together with video and is independent of the image recording rate. Though the audio record control is done in the Camera #1 screen, there is no specific camera allocation.
1.8 ALARM CONTACTS INSTALLATION
The alarm inputs can be used to start recording or for recording rate adjustment. In addition, alarm reactions such as camera display on the monitor, buzzer, e-mail and network alarm are available. The alarm output relay can be switched if required. Alarm input response actions can be controlled according to a flexible schedule.
7
1.8.1Alarm Input Contacts
This DVR provides one alarm input per camera. All inputs are programmable N.O. (Normal Open) or N.C. (Normal Closed) Inputs have to be switched by dry contacts.
Alarm input with N.O. (Normal Open) contact in idle state
Alarm input with N.C. (Normal Closed) contact in idle state
All settings are programmed in the ALARM menu (Section 0).
1.8.2Alarm Output Relay
The relay output provides either Normally Open or Normally Closed dry contacts.
Output relay in idle state
1.9 RS-485 keyboard / PTZ Installation
All functions can be remote-controlled by the EKB-500 universal keyboard. Using the EEPbus protocol, digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One system can comprise up to 8 keyboards.
1.9.1General RS-485 bus installation
The EKB-500 keyboard uses a RS-485 simplex wiring; the signal is transferred via a single twisted pair line. CAT5 network cable is recommended, UTP version (unshielded) is sufficient for normal applications. A shielded cable should be used if the installed cables are expected to be highly susceptible to interference. The number of devices installed in one bus is limited to 32, and the maximum cable length is 3,900 feet. Both of these can be expanded using a signal distributor (see below).
Both the first and the last device in series should be terminated with 120 Ohm resistance in order to minimize line reflections.
RS-485 bus serial wiring
8
Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes.
RS-485 bus serial wiring with connector boxes and connection cable
A direct RS-485 bus star wiring is not supported unless using a signal distributor (see below).
Improper RS-485 bus star wiring
A RS-485 signal distributor may be used to use a star wiring configuration.
Star wiring with RS-485 signal distributor
A RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an additional 1200m, and it also enables the additional connection of 31 further devices to each output (the output itself represents one device).
The maximum system expandability depends on the RS-485 address range of the installed devices.
9
System expansion with RS-485 signal distributor
ATTENTION: Most signal distributors are unidirectional! This means that the signal only flows from the input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with these types of signal distributor!
1.9.2RS-485 socket pin assignment
The RS485 pin assignment is as follows:
1.9.3EKB-500 connection with network patch cable
For a simple, short distance installation, recorder and keyboard can be connected directly using a standard CAT5 network cable with an 8-pin connector at only one end, and at the other end the Pin 3 wire connected to RS485 “+” (plus) and the pin 6 wire connected to RS-485 “-“ (minus).
1.9.4EKB-500 connection to several DVRs
For long distance installations connecting several DVRs, please use a signal distributor to connect
For further details on keyboard connection, please refer to the EKB-500 manual.
RS-485 port communication settings are configured in the I/O CONTROL menu (Section 5.10.4 System Setup: I/O - control).
1.9.5Speed Dome Installation
Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional PowerCon software if the DVR is connected to a network. Local telemetry control is provided by USB - mouse control or by the optional EKB-500 keyboard.
Supported protocols: EverFocus, Pelco-D, Pelco-P, Samsung, Transparent
Required DVR settings: RS-485 receiver address in CAMERA menu (Section 4.3)
RS-485 parameters and protocol in the I/O CONTROL menu (Section 5.10.4)
ATTENTION: Some Pelco-D / -P protocol domes and receivers require an address offset of -1, i.e. the address assigned to the dome / receiver in the DVR camera menu must be 1 below the address set in the dome / receiver itself!
10
1.10USB-Mouse installation
Connect the USB mouse to one of the 2 USB ports. (This can be done while DVR is powered on) The rear USB V1.0 port is recommended to reserve the higher speed front USB V2.0 port for video copy/export.
NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless USB mouse is not supported.
1.11NETWORK CONNECTION
This section only describes physical connection to an Ethernet network. This step must be completed before the DVR can connect to the network. There are two basic types of connection:
1.11.1 Direct PC Connection through Crossover Network Cable
The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a 10/100/1000 Mbps compatible network connection.
Figure 1-3 Direct PC Connection
Pinout of crossover-cable
11
1.11.2 Network Connection through Patch Cable
The connection to an existing network requires a normal patch cable (straight-through). The illustration shows the connection to a network switch or router.
Figure 1-4 Network Connection through Patch Cable
Pinout of straight patch cable
1.12FINAL INSTALL PROCESS
Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in the power source. The POWER LED will light up if power is normal. Once the system has finished loading, you can begin to set up the menu options for the DVR.
12
Chapter
3
2 MOUSE AND FRONT PANEL OPERATION
ECOR264-4/ECOR264-8 DVRs support multiple sources to control the DVR. It can be controlled with a mouse, the front panel, an EKB500, and the handheld remote control.
This chapter will cover the basic operation using the mouse and the front panel buttons.
2.1 GENERAL USB MOUSE OPERATION
2.1.1How to select a channel / Enable audio
1.In a view consisting of more than one channel, users can select a channel by clicking once on the desired channel screen. The selected screen will be highlighted by a white frame.
2.Double clicking on a channel screen will display full screen for this channel.
3.To enable audio out, click the audio icon (ex: 
) at lower side of the screen. This system has only one audio out. Click this button to enable or disable the audio-out mode.
2.1.2OSD Root Menu
1. Right-click the mouse to obtain the DVR control bar (see Figure 2-1 OSD Root Menu ). When you move the mouse over each icon, its title will be displayed at the top of the control bar.
Figure 2-1 OSD Root Menu
2.Click on any icon to perform that action. These actions are covered in detail in Chapter 3.
3.Click the “X” in the top-right corner to close the DVR control bar.
2.1.3Operation in the Configuration Menus
13
Click on the 
icon to access the Configuration Menu.
The Configuration menu screens (shown in Figure 2-2 OSD Menu) are divided into 3 main sections.
○1
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
||
○ |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
○ |
|
|
|
|
|
|
|
|
|
Figure 2-2 OSD Menu
○1 In section 1, there are ten setup options available. Move the mouse over an icon and click to select it.
○2 In section 2, the categories for the selected icon will be displayed. Click on a choice to select it.
○3 In section 3, all the options for the selected choice will be available. Click on a field to make changes.
2.1.4Field Input Options
The following are examples of different types of fields available in the Configuration menu.
Textbox: Click on the box and an on-screen keyboard will appear*. (see note about the on-screen keyboard below)
Dropdown box: Click on the down arrow to see all selections, then directly click on an option to select it.
Check box: Click on the box to enable it (checked) or disable it (unchecked).
Button: Click the button to execute the function.
14
Bar: Click and hold on the bar to adjust the set point Left or Right.
* Note about on-screen keyboard:
Click on a button to input that character.
The buttons on the right and bottom have the following functions:
Delete |
Delete the letter |
|
|
Done |
Confirm the selection |
|
|
All Caps |
Switch to capital letters |
|
|
Space |
Enter a space |
|
|
← |
Move to left |
|
|
→ |
Move to right |
|
|
Cancel |
Cancel and exit from the keyboard |
|
|
.
15
2.2 General Front Panel Operation
2.2.1 How to select a channel / Enable audio
1.In a view consisting of more than one channel, use the mouse or press arrow keys (Up/Down/Right/Left) to scroll through each channel that is displayed. The selected channel will be highlighted by white frame. Pressing the “right” arrow when the last camera (4 or 8) is highlighted will select all cameras.
2.While channel #1 is selected, press the “Enter” button to turn Audio On/ Off.
2.2.2 OSD Root Menu
1.Press “Menu” key to display the DVR control bar. Use the left/right arrows to scroll over each icon. The title for each icon will be displayed on top of the control bar.
2.Press “Enter” key on any icon to perform that action. These actions are covered in detail in Chapter 3
3.Press “Menu” to close the DVR control bar.
○1
2 |
|
|
|
|
|
|
|
3 |
|
|
|
|
|||||
○ |
|
|
|
|
|
|
|
○ |
|
|
|
|
|
|
|
|
|
Figure 2-3 OSD Menu
○1 In section 1, there are ten setup options available. Use arrow keys to highlight an icon and press “Enter” to select it.
○2 In section 2, the main choices for the selected icon will be displayed. Use Up/Down arrow keys to highlight a choice and press “Enter” to select it.
○3 In section 3, all the options for the selected choice will be available here. Use arrow keys to move between items and press “Enter” to make changes.
Note: press “Menu” button to go back to the previous menu section.
2.2.5Field Input Options
Textbox: Press Enter key and an on-screen keyboard will appear*. (see note about on-screen keyboard below)
Dropdown box: Press “Enter” key to show the available options. Use arrow keys to highlight the desired option and press “Enter” again to select it.
Check box: Press “Enter” key on a setting to enable it (checked) or disable it (unchecked).
Button: Press “Enter” key to execute the function.
17
Bar: Press “Enter” key to activate the slider, then use arrow keys to adjust the setting. Press “Enter” again to finalize the changes.
* Note about on-screen keyboard:
Click on a button to input that character.
The buttons on the right and bottom have the following functions:
Delete |
Delete the letter |
Done |
Confirm the selection |
All Caps |
Switch to capital letters |
Space |
Enter a space |
← |
Move to left |
→ |
Move to right |
Cancel |
Cancel and exit from the keyboard |
18
Chapter
3
3. GENERAL DVR OPERATIONS
This chapter introduces the operations on major functions including playback, layout change, sequence, triplex operations, copy, and search.
3.1 RECORD
By default, the DVR will always be in record mode. When the DVR is turned on, it will start to record. The exceptions are:
1.DVR will not record any uninstalled cameras (Refer to Section 4.3.1 for more details)
2.If a schedule is active, the DVR will follow the record settings of the schedule.
3.2 LOGIN
In order to access ECOR264-4/ECOR264-8 options, users may be asked to log in for authority identification. To log in, follow these steps.
1.Right click on the screen or press the Menu Key to display the Main Menu
2.Choose or click (or press “Enter” key) on the Configuration icon to bring up the following screen:
Figure 3-1 Login page
3. Select the user name from the drop-down list and input the password. The defaults are:
User name: admin (lower case)
Password: 11111111
+ To input password by mouse: click the password field to bring up the on-screen keyboard (see Figure 3-2 On-screen Keyboard). Click on each button to input the desired characters for the password. When finished, click “Done” on the on-screen keyboard to confirm the password.
19
+To input password using front panel: press “Enter” key to show the on-screen keyboard (see Figure 3-2 On-screen Keyboard). Use the arrow buttons to highlight each character and press the “Enter” key on the front panel to input the selected characters. When finished, highlight “Done” and press the “Enter” key on the front panel to confirm the password.
+Click (or press “Enter” key) on the “Login” button to log in to the system.
Figure 3-2 On-screen Keyboard
3.3 SELECT CAMERA OPERATION
ECOR264-4/ECOR264-8 is a pentaplex DVR; users can control each camera individually by selecting that camera. For camera selection:
Mouse: Right-click the screen, the image will show a white frame on screen if the camera has been selected. When in quad display mode, press the quad layout icon in layout menu to select all four cameras.
4.Front panel: Use the arrows to change the selection. Pressing the “right” arrow when the last camera (4 or 8) is highlighted will select all cameras.
3.4 CHANGE AUDIO OUTPUT OPERATION
Use arrow keys to select camera #1 and press “Enter” key to switch audio output on and off. An audio icon 
will appear on the screen. Please make sure “Record Audio” option under Camera 1 Basic Settings setup menu is ON if audio recording is required. Also, the audio source and/or audio output amplifier have to be connected properly in order to utilize the audio functions. Note: Only Cam#1 controls audio, all others do not control audio.
3.5 PLAYBACK
The playback bar is the fastest way to show video from the exact time which users want to see. The playback bar allows a user to see both a time line and the current playback indicator. The user can then click the time line to move the indicator to the position which they want to see. The operation is as follows:
20
To playback:
By mouse: Right-click to bring up the menu bar and click on 
to enter Playback Menu. By front panel: Press 
key to enter Playback Menu.
The playback bar will show (see figure below):
1 |
2 |
3 |
4 |
9 |
10 11 13 |
5 |
6 |
7 |
8 |
|
|
|
12 10 10 |
2009/05/25 09:09:30PM |
2009/05/25 09:09:40PM |
2009/05/25 09:10:30PM |
|||||
|
|
|
|
|
|
|
|
|
|
|
14 |
15 |
16 |
||
1.Stop key: press to stop playback
2.Slow Reverse key: press to start slow reverse playback
3.Pause key: press to pause playback
4.Slow Forward key: press to start slow forward playback
5.Fast Reverse key: press to start fast reverse playback
6.Reverse key: press to start reverse playback
7.Forward key: press to start forward playback
8.Fast Forward key: press to start fast forward playback
9.Time bar: Move the slider on the time bar to the select time to playback (The start time and end time for time bar appears below the bar). The status of each camera is represented by different colors on the time bar. Green means normal; orange indicates a Motion; blue indicates Video Loss, red indicates an alarm event.
10.“+” and “-“ signs are used to adjust the time scale range for the bar. Press “+” or “-“ to select between scale levels L1 ~ L5. When changing level, the start time and end time of the time bar will change)
L1: Entire time bar is 2 days L2: Entire time bar is 30 hours. L3: Entire time bar is 1 hour.
L4: Entire time bar is 10 minutes. L5: Entire time bar is 1 minute.
11.Express copy: Press to start express copy when camera during playback (only one camera)
12.Playback speed indicator
13.Press “X” to close the playback bar.
21
14.Start time for bar (the left-most point of the time bar)
15.Current playback time (the time indicated by the slider)
16.End time for time bar (the right-most point of the time bar)
3.6PTZ
3.6.1General PTZ control (if PTZ cameras are installed)
Right-click to bring up the menu bar and click on 
to display PTZ Controls.
The following actions can be performed using the PTZ Menu:
1.Use Direction Arrows (up, down, left, right) to move the camera to the desired direction and angle.
2.To Zoom, Click “Z+” to zoom closer or “Z-” to zoom farther away.
3.To Focus , click “F+” to focus far or click “F-” to focus near.
4.With Iris, you can increase the amount of light by clicking “I+” or decrease it by clicking “I-“.
5.To program a preset position (if supported by the camera)
a.Move PTZ camera to the specified position
b.Click “Preset” button
c.Click the number of the desired position (This will be displayed in the box)
d.Click “Set” button
6.To jump to a preset position
a.Click “Preset” button
b.Click the number of the desired position
c.Click “Go” button
7.Shortcut for presets #1-9
a.Click digit 1-9 button without clicking any other buttons
b.The camera will seek that preset position
8.Steps to delete a preset position (if supported by the camera)
a.Click “Preset” button
b.Click the number of the desired position
c.Click “Delete” button
9.For Auto Pan
a.Click “Auto Pan” button
10.Pattern Operation (Pattern is the “0” Tour in Everfocus and Pelco PTZ cameras)
a.Click “Pattern” button
11.Steps to run a tour
a.Click “Tour” button
b.Click the number of the desired tour
22
Loading...