Epson 400, 600, 640, EX, 700 User Manual

...
0 (0)

EPSON® USB/Parallel Adapter

User’s Guide

EPSON Stylus® COLOR 440

EPSON Stylus COLOR 1520

EPSON Stylus COLOR 600

EPSON Stylus COLOR 3000

EPSON Stylus COLOR 640

EPSON Stylus Photo 700

EPSON Stylus COLOR 660

EPSON Stylus Photo EX

EPSON Stylus COLOR 800

EPSON Stylus Pro 5000

EPSON Stylus COLOR 850

EPSON Stylus Pro 9000

CPD-7424R2

EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.

Copyright © 1999 by Epson America, Inc.

10/99

ii

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

iii

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

iv

Contents

Introduction

1

Getting Started on a Macintosh

2

Setting Up the Computer

2

Setting Up the Printer

3

Connecting the Cable

3

Installing the USB Printer Software

7

Installing Your Creative Software and Electronic Manual

10

Getting Started on a Windows 98 System

11

Setting Up the Computer

11

Setting Up the Printer

15

Connecting the Cable

15

Installing the USB Printer Software

18

Enabling Windows Print Manager

22

Checking Your Installation

24

Installing Your Creative Software and Electronic Manual

25

Appendix

27

USB/Parallel Adapter Specifications

27

System Requirements

28

v

Introduction

The EPSON USB/Parallel Adapter Kit lets you use smart cable technology to connect your EPSON printer to an Apple® iMac,Power Macintosh® G3, or Microsoft® Windows® 98 computer. It supports the following printers:

EPSON Stylus COLOR 440

EPSON Stylus COLOR 1520

EPSON Stylus COLOR 600

EPSON Stylus COLOR 3000

EPSON Stylus COLOR 640

EPSON Stylus Photo 700

EPSON Stylus COLOR 660

EPSON Stylus Photo EX

EPSON Stylus COLOR 800

 

EPSON Stylus Pro 5000*

EPSON Stylus COLOR 850

 

EPSON Stylus Pro 9000*

*The software in this kit supports these two printers for Windows 98 only. To connect one of them to an iMac or G3 using your EPSON USB/Parallel Adapter, you have to install the software that came with your printer. See your printer’s setup instructions.

To install the EPSON USB/Parallel Adapter, turn to one of these sections:

“Getting Started on a Macintosh” on page 2

“Getting Started on a Windows 98 System” on page 11

1

If you have any problems installing the cable or software, contact your EPSON dealer or EPSON technical support as described in the Where to Get Help section of your printer documentation.

Getting Started on a Macintosh

The instructions on the next few pages explain how to connect the USB/ Parallel Adapter cable to your iMac or G3 and how to install the printer software that came on the USB Printer Software CD-ROM.

IMPORTANT:

To connect an EPSON Stylus Pro 5000 or 9000 to your Macintosh using the adapter, install the software that came with your printer instead of the software included in this kit. See your printer’s setup instructions.

For all other printers, you must use the USB Printer Software CD-ROM included in this kit. Follow the instructions below.

Setting Up the Computer

If you have an iMac, you may need to update your system before installing the EPSON USB/Parallel Adapter.

If your iMac is running OS 8.1, you must install Apple’s iMac Update 1.0.

If your iMac is running OS 8.5 or 8.5.1, Apple recommends that you install iMac Update 1.1.

2

Download the update for your system at http://swupdates.info.apple.com. Contact Apple if you have problems installing the update.

To find out which operating system your iMac is running, select About This Computer in the Apple menu.

Setting Up the Printer

If you’ve been using your EPSON printer with your computer, the printer is probably set up already. If so, turn off your system and disconnect the printer from the computer. Then go to “Connecting the Cable” below to attach the USB/Parallel Adapter cable to your system.

If you’re setting up a new printer, see the documentation that came with your printer for instructions on unpacking it, installing ink cartridges, and loading paper. Then return to this booklet for instructions on connecting the cable and installing your printer software.

Connecting the Cable

You can connect the USB/Parallel Adapter directly to a USB port on your Macintosh or to a USB hub connected to a port on the Macintosh. If you have any printing problems when the printer is connected via a USB hub, try connecting the printer directly to a USB port on the computer instead.

3

Epson 400, 600, 640, EX, 700 User Manual

1Connect the adapter to an available USB port on the side of your iMac as shown, or to a USB port on the back of your G3. If you’re using a USB hub, plug it into an available USB port on your iMac or G3, then plug the adapter into a USB port on the hub. If you have more than one hub, connect the adapter to the first hub.

 

optional

 

USB hub

USB port

OR

USB/Parallel Adapter

USB/Parallel Adapter

4

You can also connect the adapter to one of the USB ports on your Macintosh keyboard. If you’re using a USB hub, plug it into the USB port on the keyboard, then plug the adapter into a USB port on the hub. If you have more than one hub, connect the adapter to the first hub.

USB port

USB/Parallel Adapter

OR

optional USB hub

USB/Parallel Adapter

5

2Connect the adapter’s parallel connector to the parallel port on the back of the printer, then secure it with the wire clips.

wire clips

parallel connector

Follow the instructions in the next section to install the printer software from the USB Printer Software CD-ROM.

6

Loading...
+ 23 hidden pages