Empire Comfort Systems BVD36FP52 User Manual

Size:
4.71 Mb
Download

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

The Keystone "B" Vent Zero Clearance Gas

Fireplace

GAS-FIRED

Installer: Leave these instructions with the consumer. Consumer: Retain these instructions for future use.

WARNING: If the information in this manual is not followedexactly,afireorexplosionmayresultcausing property damage, personal injury or loss of life.

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

-WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediatelycallyourgassupplierfromaneighbors phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire

department.

-Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

B-VENT

GAS FIREPLACE

MODEL SERIES

MILLIVOLT

BVD34FP30(F,L)N-1

BVD36FP32(F,L)N-1

BVP42FP32(F,L)N-1

DIRECT IGNITION

BVD34FP50(F,L)N-1

BVD36FP52(F,L)N-1

BVP42FP52(F,L)N-1

EFFECTIVE DATE

APRIL 2006

UL FILE NO. MH45034

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE. This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness.

19400-3-0406

Page 1

TABLE OF CONTENTS

 

Section

Page

Important Safety Information....................................................................................................

3

Safety Information for Users of LP Gas....................................................................................

4

Introduction ..............................................................................................................................

5

Specifications ............................................................................................................................

6

Fireplace Dimensions................................................................................................................

6

Clearances .................................................................................................................................

7

Locating Fireplace.....................................................................................................................

7

Gas Supply .............................................................................................................................

8-9

Installation .........................................................................................................................

10-11

Venting ...............................................................................................................................

12-13

Log Placement (BVD34 and BVD36) (5 Log Set).................................................................

14

Log Placement (BVP42) (3 Log Set)......................................................................................

15

Operating Instructions........................................................................................................

16-17

Standing Pilot Wiring Diagram...............................................................................................

18

Standing Pilot Lighting Instructions .......................................................................................

19

Standing Pilot Troubleshooting...............................................................................................

20

Standing Pilot Propane/LP Gas Conversion.......................................................................

21-22

Direct Ignition Wiring Diagram..............................................................................................

23

Optional Remote Control (120V Direct Ignition)...................................................................

23

Direct Ignition Lighting Instructions.......................................................................................

24

Direct Ignition Troubleshooting..............................................................................................

25

Direct Ignition Propane/LP Gas Conversion......................................................................

25-26

Maintenance and Service.........................................................................................................

27

BVD34 and BVD36 Parts List................................................................................................

28

BVD34 and BVD36 Parts View..............................................................................................

29

BVP42 Parts List.....................................................................................................................

30

BVP42 Parts View...................................................................................................................

31

FBB4 Optional Variable Speed Blower Installation Instructions.......................................

32-33

Junction Box Wiring Installation Instructions.........................................................................

34

OptionalAccessories...............................................................................................................

35

DecorativeAccessories............................................................................................................

36

How To Order Repair Parts.....................................................................................................

37

Service Notes......................................................................................................................

37-39

Page 2

19400-3-0406

IMPORTANT SAFETY INFORMATION

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

If this appliance is installed directly on carpeting,

• Clothing or other flammable material should not be

 

tile or other combustible material other than wood

placed on or near the appliance.

 

flooring the appliance shall be installed on a metal or

• Adequate accessibility clearances for servicing and

 

wood panel extending the full width and depth of the

proper operation.

 

appliance.

 

• This appliance must not share or be connected to a

 

Thebasereferredtoabovedoesnotmeanthefireproof

 

baseasusedonwoodstoves.Theprotectionisforrugs

flue serving a separate solid-fuelburning appliance.

 

• Keep the area around your appliance clear of

 

that are extremely thick and light colored tile.

Children and adults should be alerted to the hazards

combustiblematerials,gasolineandotherflammable

vapor and liquids.

 

of high surface temperatures and should stay away

 

• Under no circumstances should any solid fuels

 

to avoid burns or clothing ignition.

Young children should be carefully supervised when

(wood, coal, paper or cardboard etc.) be used in this

appliance.

 

they are in the same room as the appliance.

 

• The flow of combustion and ventilation air must not

 

 

 

 

be obstructed in any way.

 

 

 

Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.

Anypartremovedforservicingtheappliancemust bereplacedpriortooperatingtheappliance.Work should be done by a qualified service person.

Keep burner and control compartment clean.

Vent cap is hot while fireplace is in operation.

Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance shouldbeinspectedbeforeuseandatleastannually by a qualified service person. More frequent cleaningmayberequiredduetoexcessivelintfrom carpeting, bedding materials, etc. It is imperative thatcontrolcompartments,burnersandcirculating air passageways of the appliance be kept clean.

DO NOT put anything around the fireplace that will obstruct the flow of ventilation air.

Clearance in accordance with local installation codes and the requirements of the gas supplier.

DO keep the appliance area clear and free from combustiblematerial,gasolineandotherflammable vapors and liquids.

DO examine venting system periodically and replace damaged parts.

DO make a periodic visual check of pilot and burners. Clean and replace damaged parts.

DO NOT use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace anypartofthecontrolsystemandanygascontrol which has been under water.

Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

19400-3-0406

Page 3

SAFETY INFORMATION FOR USERS OF LP GAS

Propane (LP-Gas)is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review

them point by point with the members of your household. Somedaywhentheremaynotbeaminutetolose,everyone’s safety will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more information, please contact your gas supplier.

LP-GASWARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.That’s your signal to go into immediate action!

Do not operate electric switches, light matches, use your phone. Do not do anything that could ignite the gas.

Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.

Close all gas tank or cylinder supply valves.

LP-Gasis heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas leak, keep out of basements and other low areas. Stay out until firefighters declare them to be safe.

Useyourneighbor’sphoneandcallatrainedLP-Gasserviceperson and the fire department. Even though you may not continue to smell gas, do not turn on the gas again. Do notre-enterthe building, vehicle, trailer, or area.

Finally,lettheservicemanandfirefighterscheckforescaped gas. Have them air out the area before you return. Properly trainedLP-Gasservice people should repair the leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Somepeoplecannotsmellwell.Somepeoplecannotsmellthe odor of the chemical put into the gas. You must find out if you can smell the odorant in propane. Smoking can decrease your abilityto smell.Beingaround an odor for a timecanaffect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.

The odorant in LP-Gasis colorless, and it can fade under some circumstances.For example, if there is an underground leak,themovementofthegasthroughsoilcanfiltertheodorant. Odorants in LP-Gas also are subject to oxidation. This fading

can occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.

LP-Gasmay stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there may be more odor at lower levels. Always be sensitive to the slightest gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

LearntorecognizetheodorofLP-Gas.YourlocalLP-Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use it to find out what the propane odor smells like. If you suspect that your LP-Gas has a weak or abnormal odor, call your LP-Gas Dealer.

If you are not qualified, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gassystem. If you are qualified, consciously think about the odor ofLP-Gasprior to and while lighting pilot lights or performing service or making adjustments.

Sometimes a basement or a closed-uphouse has a musty smell that can cover up theLP-Gasodor. Do not try to light pilot lights, perform service, or make adjustments in an area where the conditions are such that you may not detect the odor if there has been a leak ofLP-Gas.

Odor fade, due to oxidation by rust or adsorption on walls of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are filled and allowed

to set too long before refilling. Cylinders and tanks which havebeenoutofserviceforatimemaydevelopinternalrust which will cause odor fade. If such conditions are suspected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-Gas dealer.AperiodicsnifftestoftheLP-Gasisagoodsafety measure under any condition.

If,atanytime,youdonotsmelltheLP-Gasodorantandyouthinkyoushould,assumeyouhavealeak.Thentakethesame immediateactionrecommendedabovefortheoccasionwhen you do detect the odorizedLP-Gas.

If you experience a complete “gas out,” (the container is undernovaporpressure),turnthetankvalveoffimmediately. If the container valve is left on, the container may draw in some air through openings such as pilot light orifices. If this occurs,somenewinternalrustingcouldoccur.Ifthevalveis left open, then treat the container as a new tank.Always be sure your container is under vapor pressure by turning it off at the container before it goes completely empty or having it refilled before it is completely empty.

Page 4

19400-3-0406

INTRODUCTION

Instructions to Installer

1.Installer must leave instruction manual with owner after installation.

2.Installer must have owner fill out and mail warranty card supplied with the fireplace.

3.Installer should show owner how to start and operate the fireplace.

This is a B-Ventgas appliance and must be installed with a listedB-Ventvent system. The information contained in this manual pertains to all models and gas control systems unless otherwise noted.

Warning: This unit is not for use with solid fuels.

Appliance Certification

This fireplace is design certified in accordance with American NationalStandard/CSAStandardANSIZ.21-50/CSA2.22andbyUnderwritersLaboratoriesasaVentedGasApplianceandshallbe installed according to these instructions.

Consult your local building code agency, prior to installation, to ensure compliance with local codes-includingpermits and inspections.

The fireplace, when installed, must be electrically grounded in accordance with local codes or, in absence of local codes, with theNational Electric Code ANSI/NFPA 70 ifanexternalelectrical source is utilized.

These models may be installed in a bedroom or bed-sittingroom in the U.S.A.

Qualified InstallingAgency

Installationandreplacementofgaspiping,gasutilizationequipment or accessories and repair and servicing of equipment shall be performedonlybyaqualifiedagency.Theterm“qualifiedagency” meansanyindividual,firm,corporationorcompanywhicheitherin personorthrougharepresentativeisengagedinandisresponsible for (a) the installation or replacement of gas piping or (b) the connection, installation, repair or servicing of equipment, who is experienced in such work, familiar with all precautions required andhascompliedwithalltherequirementsoftheauthorityhaving jurisdiction.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts. The state of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length.

Theinstallationmustconformwithlocalcodesor,intheabsenceof localcodes,withtheNational Fuel Gas Code ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation Code, or CSA B149.1

in Canada. *Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10036.

Warning: ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS.

Improper installation or use of the fireplace can cause serious injuryordeathfromfire,burns,explosions,orcarbonmonoxide poisoning.

Any alteration of the original design, installed other than as shown in these instructions or use with a type of gas not shown on the rating plate is the responsibility of the person and company making the change.

Important

All correspondence should refer to complete Model Number, Serial Number and type of gas.

HighAltitude

When installing this unit at an elevation above 2000 feet (in the United States) it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Generally, input should be reduced 4 percent for each 1000 feet above sea level. However, if the heating value of the gas has been reduced, this general rule may not apply. Check with local gas utility for proper orifice size identification.

Canadian HighAltitude

Altitude: 0-4500feet(0-1370m)

When installing this unit at an elevation above 4500 feet (in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for location.

Preparation

This gas fireplace and its components are tested and safe when installed in accordance with this Installation Manual. Report to your dealer any parts damaged in shipment, specifically check glass condition. Do not install unit with damaged, incomplete, or substitute parts. Read all instructions before starting installation andfollowtheseinstructionscarefullyduringinstallationtoinsure maximumbenefitandsafety.Failuretofollowthemwillvoidyour warranty and may present a fire hazard.

The warranty will be voided by, and the warrantor disclaims any responsibility for the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or vent system.

InstallationotherthanasinstructedbyEmpireComfortSystems, Inc.

Improperpositioningofthelogs,glassdoor,optionalaccessories or decorative rock.

Installationand/oruseofanycomponentpartnotmanufactured or approved by manufacturer.

Glass Specifications

Optional glass door kits manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosuresasdefinedbytheConsumerProductSafetyCommission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202

(Safety Glazing Certification Council SGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and

02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 "Certification and labeling requirements" which refers to15 U.S. Code(USC) 2063 stating "...Such certificate shall accompany the product or shall otherwise be furnished to any

19400-3-0406

Page 5

SPECIFICATIONS

 

BVD34FP

BVD36FP

BVP42FP

Input Btu/hr Maximum

21,000

25,000

30,000

KWH (Maximum)

6.2

7.3

8.8

B-VentSize

4" Diameter

6" Diameter

6" Diameter

NAT. (Standard)

 

 

 

Orifice

#44 (.086)

#42 (.0935)

#37 (.104)

P-252

P-286

P-213

 

Air Shutter Opening

1/8" (3.2mm)

1/8"(3.2mm)

1/8" (3.2mm)

*LP (Conversion Kit Required)

 

 

 

Orifice

1.35mm

1.45 mm

1.65mm

P-289

P-208

P-250

 

Air Shutter Opening

5/16" (7.9mm)

5/16" (7.9mm)

Full Open

Height without standoff

32 3/4"(832mm)

34 3/4"(883mm)

34 3/4"(883mm)

Width

37" (940mm)

39" (990mm)

43" (1,092mm)

Depth

14 7/8" (378mm)

18 3/8" (467mm)

18 3/8" (467mm)

Gas Inlet Shutoff Valve (Pipe)

1/2 NPT

1/2 NPT

1/2NPT

NOTE: Air shutter settings are factory minimumsettings.Some venting configurations may require minor air shutter adjustments for optimum performance.

*NOTE: LP Conversion kits are included on the 120v. direct ignition model fireplaces. For millivolt models, use kit #19160 for BVD34FP Series, kit #19161 for BVD36FP Series, and kit #19162 for BVP42FP Series.

Remote Control Options &

Description

 

Accessories

 

 

FRBC

MILLIVOLT BATTERY REMOTE ON/OFF

 

FREC

DIRECT IGNITION/MILLIVOLT 120V ON/OFF REMOTE

 

FWS-1

DIRECT IGNITION/MILLIVOLT WALL SWITCH

 

 

FIREPLACE DIMENSIONS

 

 

RIGHT SIDE VIEW

 

K

 

L

 

M

 

 

 

K

N

 

G

 

 

 

 

P

O

M

G

J

H

GAS CONTROLS BEHIND LOWER

LOUVER OR UNDER SLIDING

HEARTH ACCESS DOOR

Figure 1

Dim

BVD34

BVD36

BVP42

A

37"

39"

43"

 

940mm

990mm

1092mm

B

34"

36"

40"

864 mm

914mm

1,016mm

C

22

7/8"

24 7/8"

24

7/8"

581mm

632mm

632mm

D

35

5/8"

37 5/8"

37

5/8"

 

905 mm

956 mm

956 mm

E

32

3/4"

34 3/4"

34

3/4"

832mm

883 mm

883 mm

 

F

14

7/8"

18 3/8

18

3/8"

378mm

467mm

467mm

 

G

6 3/8"

6 3/8"

6 3/8"

162mm

162mm

162mm

H

5 7/8"

8 3/8"

6 3/8"

149mm

213mm

162mm

I

24

1/2"

22 1/2"

26

1/2"

622mm

572mm

673mm

 

J

12

1/4"

11 1/4"

13

1/4"

311mm

286mm

337mm

 

K

1 1/4"

1 1/4"

1 1/4"

32mm

32mm

32mm

L

31

3/4"

33 3/4"

33

3/4"

 

807mm

857mm

857mm

M

32

11/16"

34 11/16"

34

11/16"

 

830mm

881mm

881mm

N

2 1/16"

2 1/16"

2 1/16"

53mm

53mm

53mm

O

5 5/8"

5 5/8"

5 5/8"

143mm

143mm

143mm

P

4 7/8"

4 7/8"

4 7/8"

124mm

124mm

124mm

 

Page 6

19400-3-0406

CLEARANCES

Clearance to Combustibles

Back

0" (0 mm)

Side

0" (0 mm)

Floor

0" (0 mm)

Top Stand-off

0" (0 mm)

Top Framing Edge

1" (25mm)

SEE MANTLE CHART FOR

MAXIMUM MANTLE DEPTH

 

2" x 4" HEADER

 

STAND OFF

SEE MANTLE CHART

3" (76 mm) HEIGHT

ABOVE TOP OF

FOR MINIMUM HEIGHT

FIREPLACE

OF MANTLE ABOVE UNIT

 

FINISHED WALL

 

(COMBUSTIBLE)

 

 

NAILING

 

FLANGES

TOP FRAMING

 

LEDGE

 

GLASS FRONT

 

(OPTIONAL)

 

Figure 2

Combustible Material

No greeting cards, stockings or ornamentation of any type should be placed on or attached to the fireplace. The flow of heat can ignite combustibles.

Mantel Chart (Figure 3)

12” (305mm)

10” (254mm)

 

 

MANTEL

 

 

 

8”

COMBUSTIBLE TRIM AND MANTELS

 

 

ALLOWED IN SHADED AREA

 

 

 

12”

 

6”

 

 

 

 

 

 

 

4 ½”

 

 

 

3 3/4”

10 3/4”

 

 

3”

 

 

 

 

 

 

2 1/4”

8”

 

 

1 ½”

 

6”

 

 

 

3/4”

 

5”

 

 

 

 

 

 

4” 3”

 

 

 

2” 1”

 

TOP EDGE OF FIREPLACE

1/4”

(6.35mm)

Figure 3

Clearances (Figure 4)

Clearance from top front edge of fireplace to ceiling is 36" Clearance from side of fireplace to adjacent sidewall is 6".

Figure 4

LOCATING FIREPLACE

Note: When you install your Fireplace on wall corner positions,aminimumof6inches clearance must be maintained fromtheperpendicularsidewall and the screened opening of the appliance.

Figure 5

19400-3-0406

Page 7

GAS SUPPLY

The gas pipeline can be brought in through the right or left side of the appliance. Consult the current National Fuel Gas Code,ANSI Z223.1 CAN/CGA-B149(.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe Length

Schedule 40 Pipe

Tubing, Type L

(Feet)

Inside Diameter

Outside Diameter

 

 

 

 

 

 

Nat.

L.P.

Nat.

L.P.

 

 

 

 

 

0-10

1/2"

3/8"

1/2"

3/8"

 

12.7mm

9.5mm

12.7mm

9.5mm

 

 

 

 

 

11-40

1/2"

1/2"

5/8"

1/2"

 

12.7mm

12.7mm

15.9mm

12.7mm

 

 

 

 

 

41-100

1/2"

1/2"

3/4"

1/2"

 

12.7mm

12.7mm

19mm

12.7mm

 

 

 

 

 

101-150

3/4"

1/2"

7/8"

3/4"

 

19mm

12.7mm

22.2mm

1.9 mm

 

 

 

 

 

Note:Neveruseplasticpipe.Checktoconfirmwhetheryourlocal codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing and Fittings.

ANS Z21.45 Assembled Flexible Appliance Connectors of Other ThanAll-MetalConstruction

The above connectors may be used if acceptable by the authority having jurisdiction. The state of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length.

 

 

Figure 6

 

Gas Supply Pressure (inches w.c.)

 

Minimum

Normal

Maximum

Natural Gas

4.5"

7.0"

14.0"

LP (Propane)

10.8"

11.0"

14.0"

 

Manifold Pressure (inches w.c.)

 

 

Normal (HI)

 

Natural Gas

 

3.5"

 

LP (Propane)

 

10.0"

 

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the unit. Where none exists, or where its size or location is not adequate, contact your local authorized installer for installation or relocation.

Compoundsusedonthreadedjointsofgaspipingshallberesistant to the action of liquefied petroleum gases. The gas lines must be checked for leaks by the installer.This should be done with a soap solution watching for bubbles on all exposed connections, and if unexposed, a pressure test should be made.

Neveruse an exposed flame to check forleaks.Appliance must be disconnected from piping at inlet of control valve and pipe capped or plugged for pressure test. Never pressure test with appliance connected; control valve will sustain damage!

NOTE: The millivolt gas controls are equipped with a captured screwtypepressuretestpoint,thereforeitisnotnecessarytoprovide a 1/8" test point up stream of the control.

Ondirectignitionvalves,hexplugsmaybereplacedwithhosefittings for pressure checks, then reinstalled before operating fireplace.

When using copper or flex connector use only approved fittings.

Theapplianceandit’sindividualshutoffvalvemustbedisconnected fromsupplypipingsystemduringanypressuretestingofthatsystem at test pressures in excess of 1/2 psig (3.5kPa).

The appliance must be isolated from the gas supply piping system byclosingitsindividualmanualshutoffvalveduringanypressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5kPa).

Attention! If one of the procedures results in pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the fireplace gas valve, it will result in a hazardous condition.

Page 8

19400-3-0406

GAS SUPPLY (CONT)

Checking Manifold Pressures

Both Propane and Natural gas valves have a built-inpressure regulatorinthegasvalve.Naturalgasmodelswillhaveamanifold pressure of approximately 3.5" w.c. (.871kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 4.5" w.c. (1.120kPa) for the purpose of input adjustment to a maximum of 14.0" w.c. (3.484kPa). Propane gas models will have a manifold pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 10.8" w.c. (2.68kPa) for the purpose of input adjustment to a maximum of 14.0" w.c. (3.484kPa).

BURNER ASSEMBLY

PIEZO

IGNITER

SLIDING

VALVE ACCESS

COVER

Figure 8

GAS LINE HOLE

3 ½”

FROM FRONT OF

APPLIANCE TO

GAS LINE HOLE

BVD34 SERIES - 10”

BVD,P (36,42) - 13 ½”

Figure 7

REAR TAB (BURNER BASE)

LOCATIONS

FLEXIBLE GAS CONNECTOR

GAS SUPPLY LINE

FIREBOX BOTTOM

CUTOUT ACCESS

19400-3-0406

Page 9

INSTALLATION

Framing and Finishing

1.Choose unit location.

2.Framein fireplacewith a headeracross thetop. It is important to allow for the finished face thickness when setting the depth of the frame. See Figures 9 & 11.

3.Attachfireplacetoframingusing(4)adjustablenailingflanges. Presetdepthtosuitfacingmaterial(adjustableto1/2",5/8"or 3/4" depths).

4.Use (8) 1/2" hex-headscrews supplied in hardware package to screw through slotted holes in nailing flanges, then screw intopre-drilledholes on fireplace side. Measure from face of fireplace to face of the nailing flanges to determine final depth.

MOUNTING

BRACKETS

NAIL OR OTHER SUITABLE FASTENER

Figure 9

Vent Pipe Clearance

Note: Maintainoneinch(1")ofclearancearoundverticalventpipe.FollowtheB-Ventsysteminstructionsforinstallationrequirementsand clearances. Failure to follow theB-Ventmanufacturer's instructions may cause improper draft and possible fire hazard.

B-

Install the FreshAir Kit - BVA1

Afreshairkitisavailableasanoptionalfeaturewiththisappliance. Thefreshairkithelpstodecreasetheamountofroomairtakenby utilizing outside air for combustion. It is strongly recommended that it be installed. Installation of the fresh air kit should be performed at the framing stage of the fireplace installation.

The fresh air kit installs on the left side of the fireplace.

To install the BVA1 fresh air kit, refer to the installation instructions provided with the kit.

Note: The outside air kit can terminate at any level with the exception that it must terminate at least 1 ft below the vent termination cap. The fresh air kit inlet hood should be positioned at least 2 ft above the ground level, in a manner that will not allow snow, leaves, etc. to block the inlet.

WARNING: Exhaust products of gasoline engines are hazardous. The outside air must not be taken from a garage space, attic spaces, basements, or above the roofing where other heating appliance, fans, or chimneys exhaust or utilize the air.

Framing (Figure 11)

Fireplaceframingcanbebuiltbeforeorafterthefireplaceissetin place.Framingshouldbepositionedtoaccommodatewallcovering and fireplace facing material. The fireplace framing should be constructed of 2 x 4 lumber or heavier. The framing headers may rest on the fireplace standoffs. Refer to Figure 11 for minimum framing dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS, AND WALL COVERING DETAILS BEFORE FRAMING CONSTRUCTION BEGINS.

Framing dimension "A" includes a three inch clearance for standoffs on firebox.

TO COMBUSTIBLES

Figure 10

Page 10

19400-3-0406