Empire Comfort Systems 2 User Manual

Size:
3.89 Mb
Download

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

The Tahoe Direct Vent Zero Clearance Gas

Fireplace Heater

DIRECT VENT

GAS FIREPLACE HEATER

MODELSERIES

MILLIVOLT

DVD32FP3(0,1,2,3)(N,P)-1

DVD36FP3(0,1,2,3)(N,P)-1

DVD42FP3(0,1,2,3)(N,P)-1

DVD48FP3(0,1,2,3)(N,P)-1

DIRECT IGNITION

DVD32FP5(0,1,2,3)N-2GAS-FIRED DVD36FP5(0,1,2,3)N-2

DVD42FP5(0,1,2,3)N-2

DVD48FP5(0,1,2,3)N-2

ULFILE NO. MH30033

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

WARNING:Iftheinformationintheseinstructionsarenotfollowedexactly,afireorexplosion may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IFYOU SMELLGAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USAonly) ormobile home, where not prohibited by state orlocal codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions,thisproductcouldexposeyoutosubstances in fuel or from fuel combustion which can cause death or serious illness.

Page 1

TABLE OF CONTENTS

 

Section

Page

Important Safety Information ............................................................................................................................

3

Safety Information for Users of LP Gas ............................................................................................................

4

Requirements for Massachusetts........................................................................................................................

5

Introduction .......................................................................................................................................................

6

Specifications.....................................................................................................................................................

7

Fireplace Dimensions.........................................................................................................................................

8

Clearances..........................................................................................................................................................

9

Locating Fireplace ...........................................................................................................................................

10

Gas Supply.......................................................................................................................................................

11

Rear Vent Conversion/Vent Systems ...............................................................................................................

12

Installation ..................................................................................................................................................

13-17

Venting Fireplace-TopVent ........................................................................................................................

18-21

Venting Fireplace-RearVent.......................................................................................................................

22-23

Termination Clearances ...................................................................................................................................

24

Vent Clearances................................................................................................................................................

25

Vent System Identification...............................................................................................................................

26

Framing and Finishing................................................................................................................................

27-28

Horizontal Termination....................................................................................................................................

29

DVVK-4RE.................................................................................................................................................

30-32

DVVK-4FFlex Vent........................................................................................................................................

33

Vertical Termination ...................................................................................................................................

34-35

Log Placement ...........................................................................................................................................

36-37

Operating Instructions.................................................................................................................................

38-39

Wiring Diagram-StandingPilot.......................................................................................................................

40

Lighting Instructions-StandingPilot................................................................................................................

41

Troubleshooting-StandingPilot.......................................................................................................................

42

Wiring Diagram-DirectIgnition ......................................................................................................................

43

Optional Remote Control.................................................................................................................................

43

Lighting instructions-DirectIgnition...............................................................................................................

44

Initial Start Up Gas Line Purge........................................................................................................................

45

Troubleshooting-DirectIgnition......................................................................................................................

45

LP Gas Conversion-DirectIgnition ............................................................................................................

46-47

Maintenance and Service.................................................................................................................................

48

Parts List..........................................................................................................................................................

49

Parts View........................................................................................................................................................

50

Optional Variable Speed Blower Installation Instructions..........................................................................

51-52

Junction Box Wiring Installation Instructions.................................................................................................

53

Optional Brick Liner Installation Instructions.................................................................................................

53

Accessories .................................................................................................................................................

54-55

How To Order Repair Parts..............................................................................................................................

56

Service Notes..............................................................................................................................................

56-59

Page 2

23552-4-0408

IMPORTANT SAFETY INFORMATION

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

DO NOT OPERATE THISAPPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

If this appliance is installed directly on carpeting, tile or other combustible material other than wood flooringtheapplianceshallbeinstalledonametalor woodpanelextendingthefullwidthanddepthofthe appliance.

Thebasereferredtoabovedoesnotmeanthefireproof baseasusedonwoodstoves.Theprotectionisforrugs that are extremely thick and light colored tile.

Childrenandadultsshouldbealertedtothehazards of high surface temperatures and should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance.

Clothing or other flammable material should not be placed on or near the appliance.

Adequate accessibility clearances for servicing and proper operation.

This appliance must not share or be connected to a flue serving a separate solid-fuelburning appliance.

Keep the area around your appliance clear of combustiblematerials,gasolineandotherflammable vapor and liquids.

Undernocircumstancesshouldanysolidfuels(wood, coal, paper or cardboard etc.) be used in this appliance.

The flow of combustion and ventilation air must not be obstructed in any way.

Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.

The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance. Work should be done by a qualified service person.

Keep burner and control compartment clean.

Vent cap is hot while fireplace is in operation.

Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance shouldbeinspectedbeforeuseandatleastannually by a qualified service person. More frequent cleaningmayberequiredduetoexcessivelintfrom carpeting, bedding materials, etc. It is imperative thatcontrolcompartments,burnersandcirculating air passageways of the appliance be kept clean.

DONOTputanythingaroundthefireplacethatwill obstruct the flow of ventilation air.

Clearanceinaccordancewithlocalinstallationcodes and the requirements of the gas supplier.

DO keep the appliance area clear and free from combustiblematerial,gasolineandotherflammable vapors and liquids.

DOexamineventingsystemperiodicallyandreplace damaged parts.

DOmakeaperiodicvisualcheckofpilotandburners. Clean and replace damaged parts.

CAUTION: The glass used in your fireplace is temperedglass.Iftheglassiscrackedordamagedin anyway,itshouldbereplacedonlywithacomplete glassframeassemblyfromEmpire.Seepartsliston Page 49 for ordering.

DONOTusethisfireplaceifanyparthasbeenunder water.Immediatelycallaqualifiedservicetechnician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

23552-4-0408

Page 3

SAFETY INFORMATION FOR USERS OF LP GAS

Propane (LP-Gas)is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautionswhichcanprotectbothyouandyourfamilyfrom anaccident.Readthemcarefullynow,thenreviewthempoint

bypointwiththemembersofyourhousehold.Somedaywhen theremaynotbeaminutetolose,everyone’ssafetywilldepend on knowing exactly what to do. If, afterreading the following information, you feel you still need more information, please contact your gas supplier.

LP-GASWARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.That’s your signal to go into immediate action!

Do not operate electric switches, light matches, use your phone. Do not do anything that could ignite the gas.

Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.

Close all gas tank or cylinder supply valves.

LP-Gasis heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas leak, keep out of basements and other low areas. Stay out until firefighters declare them to be safe.

Useyourneighbor’sphoneandcallatrainedLP-Gasserviceperson and the fire department. Even though you may not continue to smell gas, do not turn on the gas again. Do notre-enterthe building, vehicle, trailer, or area.

Finally,lettheservicemanandfirefighterscheckforescaped gas. Have them air out the area before you return. Properly trainedLP-Gasservice people should repair the leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Somepeoplecannotsmellwell.Somepeoplecannotsmellthe odor of the chemical put into the gas. You must find out if you can smell the odorant in propane. Smoking can decrease yourabilitytosmell.Beingaroundanodorforatimecanaffect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.

The odorant in LP-Gasis colorless, and it can fade under some circumstances.For example, if there is an underground leak,themovementofthegasthroughsoilcanfiltertheodorant. Odorants in LP-Gas also are subject to oxidation. This fading

can occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.

LP-Gasmay stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there may be more odor at lower levels. Always be sensitive to the slightest gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

LearntorecognizetheodorofLP-Gas.YourlocalLP-Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use it to find out what the propane odor smells like. If you suspect that your LP-Gas has a weak or abnormal odor, call your LP-Gas Dealer.

If you are not qualified, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gassystem. If you are qualified, consciously think about the odor ofLP-Gasprior to and while lighting pilot lights or performing service or making adjustments.

Sometimes a basement or a closed-uphouse has a musty smell that can cover up theLP-Gasodor. Do not try to light pilot lights, perform service, or make adjustments in an area where the conditions are such that you may not detect the odor if there has been a leak ofLP-Gas.

Odor fade, due to oxidation by rust or adsorption on walls of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are filled and allowed

to set too long before refilling. Cylinders and tanks which havebeenoutofserviceforatimemaydevelopinternalrust which will cause odor fade. If such conditions are suspected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-Gas dealer.AperiodicsnifftestoftheLP-Gasisagoodsafety measure under any condition.

If,atanytime,youdonotsmelltheLP-Gasodorantandyouthinkyoushould,assumeyouhavealeak.Thentakethesame immediateactionrecommendedabovefortheoccasionwhen you do detect the odorizedLP-Gas.

If you experience a complete “gas out,” (the container is undernovaporpressure),turnthetankvalveoffimmediately. If the container valve is left on, the container may draw in some air through openings such as pilot light orifices. If this occurs,somenewinternalrustingcouldoccur.Ifthevalveis left open, then treat the container as a new tank.Always be sure your container is under vapor pressure by turning it off at the container before it goes completely empty or having it refilled before it is completely empty.

Page 4

23552-4-0408

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet abovefinishedgradeintheareaoftheventing,includingbut notlimitedtodecksandporches,thefollowingrequirements shall be satisfied:

1.INSTALLATION OF CARBON MONOXIDE DETECTORS.Atthetimeofinstallationofthesidewall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumberorgasfittershallobservethatabatteryoperated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal ventedgasfueledequipment.Itshallbetheresponsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a.In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

b.Intheeventthattherequirementsofthissubdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period,abatteryoperatedcarbonmonoxidedetector with an alarm shall be installed.

2.APPROVED CARBON MONOXIDE DETECTORS. Eachcarbonmonoxidedetectorasrequiredinaccordance with the above provisions shall comply with NFPA720 and beANSI/UL 2034 listed and IAS certified.

3.SIGNAGE.Ametalorplasticidentificationplateshallbe permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,“GAS VENT DIRECTLY BELOW.

KEEPCLEAR OFALLOBSTRUCTIONS”.

4.INSPECTION. The state or local gas inspector of the sidewallhorizontallyventedgasfueledequipmentshall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

(b)EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1.The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

2.ProductApproved side wall horizontallyvented gas fueled equipment installed in a room or structureseparatefromthedwelling,buildingor structure used in whole or in part for residential

purposes.

(d)MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipmentdoesnotprovidethepartsforventingthe flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

1.The referenced “special venting system” instructionsshallbeincludedwiththeappliance or equipment installation instructions; and

2.The “special venting systems” shall be Product Approved by the Board, and the instructions for thatsystemshallincludeapartslistanddetailed installation instruction.

(e)Acopy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

23552-4-0408

Page 5

INTRODUCTION

Instructions to Installer

1.Installer must leave instruction manual with owner after installation.

2.Installermusthaveownerfilloutandmailwarrantycardsupplied with the fireplace.

3.Installer should show owner how to start and operate the fireplace.

This direct vent gas fireplace heater is designed to operate with all combustion air being siphoned from the outside of the building and all exhaust gases expelled to the outside of the building. The informationcontainedinthismanualpertainstoallmodelsandgas control systems unless otherwise noted.

Warning: This unit is not for use with solid fuels.

Appliance Certification

This fireplace is design certified in accordance with American National Standard/CSAStandardANSI Z.21-88/CSA2.33and by Underwriters Laboratories as a Direct Vent Gas Fireplace Heater and shall be installed according to these instructions.

Consult your local building code agency, prior to installation, to ensure compliance with local codes-includingpermits and inspections.

The fireplace, when installed, must be electrically grounded in accordance with local codes or, in absence of local codes, with the

National Electric Code ANSI/NFPA 70 or Canadian Electric code, CSAC22.1, if an external electrical source is utilized.

These models may be installed in a bedroom or bed-sittingroom in the U.S.A. and Canada.

Qualified InstallingAgency

Installationandreplacementofgaspiping,gasutilizationequipment or accessories and repair and servicing of equipment shall be performedonlybyaqualifiedagency.Theterm“qualifiedagency” meansanyindividual,firm,corporationorcompanywhicheitherin personorthrougharepresentativeisengagedinandisresponsible for (a) the installation or replacement of gas piping or (b) the connection, installation, repair or servicing of equipment, who is experienced in such work, familiar with all precautions required andhascompliedwithalltherequirementsoftheauthorityhaving jurisdiction.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.

Theinstallationmustconformwithlocalcodesor,intheabsenceof local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation Code, or CSA B149.1

in Canada.*Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10036.

Warning:ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS.

Improper installation or use of the fireplace can cause serious injury or death from fire, burns, explosions, or carbon monoxide poisoning.

Any alteration of the original design, installed other than as shownintheseinstructionsorusewithatypeofgasnotshownon theratingplateistheresponsibilityofthepersonandcompany making the change.

Important

AllcorrespondenceshouldrefertocompleteModelNumber,Serial Number and type of gas.

HighAltitude

When installing this unit at an elevation above 2000 feet (in the United States) it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Generally, input should be reduced 4 percent for each 1000 feet above sea level. However, if the heating value of the gas has been reduced, this general rule may not apply. Check with local gas utility for proper orifice size identification.

Canadian HighAltitude

Altitude: 0-4500feet(0-1370m)

Wheninstallingthisunitatanelevationabove4500feet(inCanada), check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for location.

Preparation

Thisdirectventgasfireplaceanditscomponentsaretestedandsafe wheninstalledinaccordancewiththisInstallationManual.Report to your dealer any parts damaged in shipment, specifically check glass condition. Do not install unit with damaged, incomplete, or substitute parts. Read all instructions before starting installation andfollowtheseinstructionscarefullyduringinstallationtoinsure maximumbenefitandsafety.Failuretofollowthemwillvoidyour warranty and may present a fire hazard.

The warranty will be voided by, and the warranter disclaims any responsibility for the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or direct vent system.

InstallationotherthanasinstructedbyEmpireComfortSystems, Inc.

Improper positioning of the logs, glass door or decorative rock.

Installationand/oruseofanycomponentpartnotmanufactured or approved by manufacturer.

Page 6

23552-4-0408

SPECIFICATIONS

 

DVD32

DVD36

DVD42

DVD48

Input BTU/Hr Maximum

18,000

20,000

25,000

28,000

BTU/Hr Minimum (millivolt only)

14,000

14,000

18,000

20,000

KWH (Maximum)

5.3

5.9

7.3

8.2

(Minimum)

4.1

4.1

5.3

5.9

NAT.

 

 

 

 

Orifice

#46 (.081")

2.10 mm

#42 (.0935")

#39 (.0995")

P-254

P-288

P-286

P-285

 

Air Shutter Opening

1/16" (1.6 mm)

1/16" (1.6 mm)

3/16"(4.8 mm)

1/8" (3.2 mm)

LP

 

 

 

 

Orifice

#56 (.0465")

#55 (.052")

1.45 mm

#52 (.0635")

P-287

P-182

P-208

P-185

 

Air Shutter Opening

1/4" (6.3 mm)

5/16" (7.9 mm)

5/16" (7.9 mm)

5/16"

(7.9 mm)

 

 

 

 

Height without standoff

32 3/4" (832 mm)

32 3/4"(832 mm)

34 3/4"(883 mm)

34

3/4"(883 mm)

Width

34" (864 mm)

37" (940 mm)

43" (1092 mm)

49"

(1245 mm)

 

 

 

 

Depth

16 3/8" (416 mm)

16 3/8" (416 mm)

16 3/8" (416 mm)

16 3/8"

(416 mm)

Gas Inlet Shutoff Valve (Pipe)

1/2 NPT

1/2 NPT

1/2 NPT

1/2NPT

NOTE: Air shutter settings are factory minimum settings. Some venting configurations may require minor air shutter adjustments for optimum performance.

Remote Control Options

Description

&Accessories

 

FRBC

Millivolt Battery Remote ON/OFF

FRBTC

Millivolt Battery Remote Thermostat

FREC

Direct Ignition/Millivolt 120V ON/OFF Remote

TMW

Millivolt Wireless Wall Thermostat

TRW

Millivolt Reed Switch Wall Thermostat

FWS-1

Direct Ignition/Millivolt Wall Switch

Venting Options

Description

DVVK-4TSP

Top vent kit (horizontal) - 4½" to 6" (114.3 mm to 152 mm) wall thickness

(DVVK-4TS)

 

DVVK-4TP

Top vent kit (horizontal) - 8" to 12" (203 mm to 305 mm) wall thickness

(DVVK-4T)

 

DVVK-4RP

Rear vent kit (horizontal) - 5" to 7" (127 mm to 178 mm) wall thickness

(DVVK-4R)

 

DVVK-4VP

Vertical vent kit

(DVVK-4V)

 

DVVK-4F

Horizontal flex vent kit (4' FLEX)

DVVK-4RE

Horizontal round termination (wall thickness up to 11 7/16")

DV822

Vinyl siding kit for DVVK-4RE

23552-4-0408

Page 7

FIREPLACE DIMENSIONS

RIGHT SIDE VIEW

J

H

K

Dim

DVD32

DVD36

DVD42

DVD48

A

34"

37"

43"

49"

 

864 mm

940 mm

1092 mm

1245 mm

B

31"

34"

40"

46"

 

787 mm

864 mm

1016 mm

1168 mm

C

23 1/16"

23 1/16"

25 1/16"

25 1/16"

 

585 mm

585 mm

636 mm

636 mm

D

35 5/8"

35 5/8"

37 5/8"

37 5/8"

 

905 mm

905 mm

956 mm

956 mm

E

32 3/4"

32 3/4"

34 3/4"

34 3/4"

 

832 mm

832 mm

883 mm

883 mm

F

16 3/8"

16 3/8"

16 3/8

16 3/8"

 

416 mm

416 mm

416 mm

416 mm

G

24 1/2"

24 1/2"

26 1/2"

26 1/2"

 

622 mm

622 mm

673 mm

673 mm

H

7 1/8"

7 1/8"

7 1/8"

7 1/8"

 

181 mm

181 mm

181 mm

181 mm

I

21 1/2"

24 1/2"

30 1/2"

36 1/2"

 

546 mm

622 mm

774 mm

927 mm

J

10 3/4"

12 1/4"

15 1/4"

18 1/4"

 

273 mm

311 mm

387 mm

464 mm

K

9 1/4"

9 1/4"

9 1/4"

9 1/4"

 

235 mm

235 mm

235 mm

235 mm

Figure 1

Page 8

23552-4-0408

CLEARANCES

 

Clearance to Combustibles

 

Back

0" (0 mm)

 

Side

0" (0 mm)

 

Floor

0" (0 mm)

 

Top Stand-off

0" (0 mm)

 

Top Framing Edge

3" (76 mm)

SEE MANTLE CHART FOR

 

MAXIMUM MANTLE DEPTH

 

SEE MANTLE CHART FOR MINIMUM HEIGHT OF MANTLE ABOVE UNIT

FINISHED WALL (COMBUSTIBLE)

NON-COMBUSTIBLE

FIRST 3(SEE MAGNIFIED VIEW)

2" x 4" HEADER

STAND OFF 3" (76 mm) HEIGHT ABOVE TOP OF FIREPLACE

3"

NAILING

FLANGES

Mantel Chart (Figure 3)

 

 

 

12” (305mm)

 

 

 

10” (254mm)

 

 

 

MANTEL

 

 

 

8”

 

COMBUSTIBLE TRIM AND MANTELS

 

 

ALLOWED IN SHADED AREA

 

 

 

15”

6”

 

 

(381mm)

 

 

 

 

 

 

 

4 ½”

 

13 3/4”

3 3/4”

 

 

 

 

 

 

3”

 

11”

 

2 1/4”

 

 

1 ½”

 

9”

 

 

 

 

 

8”

 

3/4”

 

7” 6”

 

 

 

 

 

5”

4”

3”

 

 

TOP EDGE OF FIREPLACE

TOP FRAMING

LEDGE

GLASS FRONT

Figure 2

Combustible Material

No greeting cards, stockings or ornamentation of any type should be placed on or attached to the fireplace. The flow of heat can ignite combustibles.

Note: When using Empire EMBF, UMC, and UMF Series Full Mantels with DVD32 and DVD36 Series Fireplaces, combustible clearance may be reduced to 1" clearance from top edge of fireplace face.

Figure 3

Clearances (Figure 4)

Clearance from top front edge of fireplace to ceiling is 36" Clearance from side of fireplace to adjacent sidewall is 6".

Figure 4

23552-4-0408

Page 9

LOCATING FIREPLACE

CORNER

CABINET

INSTALLATION

INSTALLATION

ISLAND

FLUSH WALL

INSTALLATION

INSTALLATION

ANGLED CORNER

 

INSTALLATION

ROOM DIVIDER

INSTALLATION

Note: Island (C) and Room Divider (D) installation is possible as long as the horizontal portion of the vent system (H) does not exceed 20 feet with a minimum vertical run of 8 feet. See details in Venting Section.

When you install your Direct Vent Fireplace in (D) Room divider or (E) Flat on wall corner positions, a minimum of 6 inches clearance must be maintained from the perpendicular wall and the front edge of the appliance.

Figure 5

Page 10

23552-4-0408