SLC195EM8 2
WATCHING TVINTRODUCTION PREPARATION INITIAL SETTING
OPTIONAL SETTING
INFORMATION
TROUBLESHOOTING
© 2007 Funai Electric Co., Ltd.
HIGH-DEFINITION TELEVISION
TO RECEIVE DIGITAL/ANALOG SIGNAL,
YOU MUST CONNECT ANTENNA.
19” Digital LCD TV
Owner’s Manual
SLC195EM8 2
SLC195EM8
TM
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSO N RADIO CORP., PARSIPPANY, NEW JERS EY, U.S. A.
NEED HELP?
PLEASE CALL TOLL FREE!
1-800-256-2487
OR VISIT OUR WEB SITE AT
www.EmersonAudioVideo.com
2
EN
I
NTRODUCTION
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the apparatus is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the apparatus and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug this apparatus from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: An apparatus that is meant for uninterrupted service
and, that for some speci c reason, such as the possibility of the loss
of an authorization code for a CATV converter, is not intended to
be unplugged by the user for cleaning or any other purpose, may
exclude the reference to unplugging the apparatus in the cleaning
description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the apparatus manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this apparatus near water,
for example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this apparatus
on an unstable cart, stand, tripod, bracket, or
table. The apparatus may fall, causing serious
injury to someone, and serious damage to
the apparatus. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the apparatus.
Any mounting of the apparatus should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
An apparatus and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
apparatus and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé que sur un meuble
(avec ou sans roulettes) recommandé par le fabricant. Si vous l’
installez sur un meuble à roulettes, déplacez les deux ensembles
avec précaution. Un arrêt brusque, l’utilisation d’une force
excessive et des surfaces irrégulières risquent de déstabiliser l’
ensemble et de le renverser.
9. VENTILATION - Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the apparatus and to protect it from overheating,
these openings must not be blocked or covered. The openings
should never be blocked by placing the apparatus on a bed, sofa,
carpet, rug, or other similar surface. This apparatus should never
be placed near or over a radiator or heat register. This apparatus
should not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
10. POWER SOURCES - This apparatus should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your apparatus dealer or local power company. For apparatuses
intended to operate from battery power, or other sources, refer to
the operating instructions.
11. GROUNDING OR POLARIZATION - This apparatus is equipped
with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will t into the power outlet
only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should
still fail to t, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the apparatus.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the apparatus, be sure the antenna or
cable system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
14. LIGHTNING - For added protection for this apparatus during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
apparatus due to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of re or electric shock.
Important Safeguards
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMP
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
Precautions5
The model and serial numbers of this unit may be found on the cabinet.
You should record and retain those numbers for future reference.
Serial No.:
Model No.:
The caution marking is located on the rear or bottom of the cabinet.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the apparatus.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
apparatus’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
3
EN
INTRODUCTION
PREPARATION
INITIAL SETTING
OPTIONAL SETTING TROUBLESHOOTING
WATCHING TV INFORMATION
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this apparatus through openings as they may touch dangerous
voltage points or short out parts that could result in a re or electric
shock. Never spill liquid of any kind on the apparatus.
18. SERVICING - Do not attempt to service this apparatus yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to quali ed service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this apparatus from the
wall outlet and refer servicing to quali ed service personnel under
the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the apparatus.
c. If the apparatus has been exposed to rain or water.
d. If the apparatus does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjustment
of other controls may result in damage and will often require
extensive work by a quali ed technician to restore the apparatus
to its normal operation.
e. If the apparatus has been dropped or damaged in any way.
f. When the apparatus exhibits a distinct change in performance,
this indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts speci ed by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in re, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
apparatus, ask the service technician to perform routine safety
checks to determine that the apparatus is in proper operating
condition.
22. HEAT - This apparatus product should be situated away from heat
sources such as radiators, heat registers, stoves, or other products
(including ampli ers) that produce heat.
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond.
FCC WARNING
This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may
cause harmful interference unless the modifications are expressly approved in the manual. The user could
lose the authority to operate this apparatus if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this apparatus does cause harmful interference to radio or television reception, which can be
determined by turning the apparatus off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the apparatus and receiver.
3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
LOCATION AND HANDLING
• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.
• Avoid a place with drastic temperature changes.
• Install the unit in a horizontal position. Do not place anything directly on top or bottom of the unit. Depending on your external devices,
noise or disturbance of the picture and/or sound may be generated if the unit is placed too close to them. In this case, please ensure
enough space between the external devices and the unit
• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• Do not put your fingers or objects into the unit.
NOTE ABOUT RECYCLING
• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with
your local recycling regulations.
• Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations
concerning chemical wastes.
4
EN
I
NTRODUCTION
Supplied Accessories5
owner’s manual
(1EMN22719A)
remote control
(NF604UD)
batteries
(AA x 2)
Phillips pan screw for
attaching the stand x 2
(FPH34140)
Symbols Used in this Manual
The following is the description for the symbols used
in this manual. Description refers to:
DTV
: Digital TV operation
TV
: Analog TV operation
• If neither symbol appears under the function
heading, operation is applicable to both.
Trademark Information
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Product that have earned ENERGY STAR® are designed
to protect the environment through superior energy
efficiency.
5
5
•
•
Attaching the Stand
You must attach the stand to the unit to display upright. Be sure the front and rear of the stand match the proper direction.
1
Turn the main unit over and place
it onto a table which has a soft
cloth draped over it. Make sure
not to damage the screen.
2
Insert the stand all the way to the
main unit slowly.
Make sure not to put the AC cord
between the stand and the unit.
3
Drive Phillips pan screws in the 2
threaded holes with a screwdriver
tightly.
Note:
• When attaching the stand, ensure that all screws are tightly fastened. If the stand is not properly attached, it could cause the unit to fall,
resulting in injuries as well as damage to the unit.
• Make sure to use a table which can support the weight of this unit and is larger than this unit.
• Make sure the table is in a stable location.
5
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
Tilt Stand
You can adjust the stand to change the angle
of the TV (-3° to 8°).
-3°
8°
5
5
EN
INTRODUCTION
PREPARATION
INITIAL SETTING
OPTIONAL SETTING TROUBLESHOOTING
WATCHING TV INFORMATION
Contents5
INTRODUCTION
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tilt Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Buttons on the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PREPARATION
Basic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INITIAL SETTING
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WATCHING TV
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching Each Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TV Screen Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OPTIONAL SETTING
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DTV Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DTVCC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Back Light Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General Speci cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Electrical Speci cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Other Speci cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
• DTV/TV/CATV
- You can use your remote control to select channels which
are broadcast in digital format and conventional analog
format. Also, cable subscribers can access their cable TV
channels.
• Information Display (DTV only)
- You can display the title, contents and other information
of the current DTV program on the TV screen.
• Auto Channel Scan
- This unit automatically scans and memorizes channels
available in your area, eliminating difficult setup
procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for closed
caption supported programming.
• MTS/SAP Tuner
- Audio can be selected from the remote control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal and
no operation for 15 minutes, the unit will turn itself off
automatically.
• Sleep Timer
- This feature will automatically turned off the power of the
unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• Stereo Sound Function
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets you tune
directly to any channel using the channel number buttons
on the remote control.
• PC Input
• Component Video Input
• S-video Input
• AV Input
• Digital Audio Coaxial Output
Features5
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded
or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai.
Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without
the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express
written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing
contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the
trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall
aggressively enforce its intellectual property rights to the fullest extent of the law.
6
EN
I
NTRODUCTION
Buttons on the Remote Control5
1
12
11
14
15
13
3
7
5
2
6
8
10
9
4
1. POWER (p11)
Press to turn the unit on and off.
2. MUTE
(p13)
Press to turn the sound on and off.
3. SLEEP (p14)
Press to activate the sleep timer.
4. Number buttons (p13)
• Press to select channels.
-/ENT.
• Press to shift the minor channel
from the major channel.
+100
• Press to select 100 or higher
channels. (CATV)
• Press to search if there are minor
channels on the currently selected
major channel. (DTV)
5. CH.
K
/
L
(p13)
Press to select channels and the
external input modes.
6. VOL.
X
/
Y
(p13)
Press to adjust the volume.
7. ENTER (p11)
Press to decide the command of
setting when the main menu is
displayed.
8. SETUP (p11)
Press to display the main menu.
9.
s
/
B
/
K
/
L
(p11)
Press to move left/ right/ up/
down through the items.
10. RETURN
Press to return to previous menu
operation.
11. INPUT (p13)
• Press to access connected
external devices like a DVD player
or VCR.
• Press to switch between the
digital mode (DTV) and analog
mode.
12. DISPLAY (p15)
Digital Mode (DTV)
• Press to display the channel
information, signal type and TV
setting.
Analog Mode (TV)
• Press to display the channel
number, signal type and TV
setting.
External Input Mode
• Press to display the external
input modes, signal type and TV
setting.
13. AUDIO (p14)
Digital Mode (DTV)
• Press to select the audio
language.
Analog Mode (TV)
• Press to select the audio mode.
14. SCREEN MODE (p16)
Press to select aspect ratio
available for the TV screen.
15. CH. RECALL
(p13)
Press to return to previous channel.
Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
21 3
5
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
7
EN
INTRODUCTION
PREPARATION
INITIAL SETTING
OPTIONAL SETTING TROUBLESHOOTING
WATCHING TV INFORMATION
1. POWER (p11)
Press to turn the unit on and off.
2. INPUT SELECT (p13)
Press to access connected external devices like a
DVD player or VCR.
Press to decide the command of setting when the
menu is displayed.
3. CHANNEL
K
/
L
(p13)
Press to select channels or move up/down through the
main menu items.
4. VOLUME
X
/
Y
(p13)
Press to adjust the volume or move right (
X
)
/
left (
Y
)
through the main menu items.
5. SETUP (p11)
Press to display the main menu.
6. infrared sensor window
Receives infrared rays transmitted from the remote
control.
7. power on indicator
Lights up when power is on.
8. standby indicator
Lights up in standby mode.
•
•
Control Panel5
Rear Panel5
1. PC input jack (p10)
VGA cable connection for PC.
2. audio input jack for PC connection (p10)
Mini-plug audio cable connection for PC.
3. antenna input jack (p8)
RF coaxial cable connection for your antenna or
cable /satellite box.
4. headphone jack
Headphone connection for personal listening.
5. component video and audio input jack (p9)
Component video and RCA audio connection for
external devices.
6. audio input jack (p9)
RCA audio connection for external devices.
7. video input jack (p10)
RCA video connection for external devices.
8. S-video input jack (p9)
S-video connection for external devices.
9. coaxial digital audio output jack (p10)
Coaxial digital audio connection for a decoder or an
audio receiver.
10. AC power cord
Connect to a standard AC outlet to supply power to
this unit.
INPUT SELECT
SETUP
POWER
VOLUME
CHANNEL
6
7
8
5
2
3
4
1
side of the unit
VIDEO 2
AUDIOCOMPONENT
LR
AUDIO
LR
VIDEOS-VIDEO
COAXIAL
PrPbY
VIDEO 1
side of the unit
rear of this unit
side of the unit
8
7
6
5
9
10
4
3
2
1
8
EN
P
REPARATION
Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Connection]
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
or
VHF / UHF
antenna
cable TV
company
rear of this unit
RF coaxial cable
Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 11.)
Note:
• For your safety and to avoid damage to this unit, please unplug the RF coaxial cable from the antenna input jack before moving the
unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than
settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Use an RF coaxial cable to connect the antenna input jack of the unit to the antenna output jack of the cable/satellite box.
e.g.)
STEREO
PCM
ANT OUTANT IN
rear of this unit
RF coaxial cable
RF coaxial cable
cable/satellite box
satellite dish
or
cable TV
company
* Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
5
*
Cables not included.
Please purchase the necessary cables at your local store.
9
EN
WATCHING TVINTRODUCTION
PREPARATION
INITIAL SETTING
OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
External Device Connection
[Component Video Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s component video input jacks, connect an RCA audio cable to the audio L/R jacks of
VIDEO2.
e.g.)
CHAPTER 15
REPEAT A-B
TITLE 5
VIDEO 2
AUDIOCOMPONENT
LR
AUDIO
LR
VIDEOS-VIDEO
COAXIAL
PrPbY
VIDEO 1
COMPONENT VIDEO OUT
Pb/Cb Pr/CrY
AUDIO OUT
RL
rear of this unit
RCA audio cable
component video cable
DVD player with
the component video jacks
(red)(blue)(green)
(red)
(red)
(blue)
(blue)
(green)
(green)
(red)(blue)(green)
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals.
[S-video Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s S-video input jack, connect an RCA audio cable to the audio L/R jacks of VIDEO1.
e.g.)
CHAPTER 15
REPEAT A-B
TITLE 5
VIDEO 2
AUDIOCOMPONENT
LR
AUDIO
LR
VIDEOS-VIDEO
COAXIAL
PrPbY
VIDEO 1
AUDIO OUT
RL
S-VIDEO
OUT
rear of this unit
RCA audio cable
S-video cable
DVD player with
the S-video output jack
Note:
• If you connect to the S-video input jack and the video input jack at the same time, the S-video connection will have priority.
5
Cables not included.
Please purchase the necessary cables at your local store.
10
EN
P
REPARATION
[Video Connection]
RCA video connection offers standard picture quality for video devices connected to the unit.
If you connect to the unit’s video input jack, connect an RCA audio cable to the audio L/R jacks of VIDEO1.
When the audio jack of the video device is monaural, connect an RCA audio cable to the audio L input jack.
e.g.)
STEREO
STAND-BY
VIDEO 2
AUDIOCOMPONENT
LR
AUDIO
LR
VIDEOS-VIDEO
COAXIAL
PrPbY
VIDEO 1
AUDIO OUT
RL
VIDEO
OUT
rear of this unit
RCA audio cable
RCA video cable
camcorder video game
VCR
Note:
• If you connect to the S-video input jack and the video input jack at the same time, the S-video connection will have priority.
[Digital Audio Output Connection (for digital broadcasting only)]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
e.g.)
VIDEO 2
AUDIOCOMPONENT
LR
AUDIO
LR
VIDEOS-VIDEO
COAXIAL
PrPbY
VIDEO 1
DIGITAL AUDIO
COAXIAL IN
rear of this unit
digital audio coaxial cable
Dolby Digital
decoder
[PC Connection]
This unit is equipped with a PC input jack. If you connect this unit to your PC, you can use this unit as a computer
monitor.
e.g.)
mini-plug audio cable
VGA cable
VGA cable should be
with ferrite core.
personal computer
rear of this unit
Note:
• Please purchase the VGA cable that has a ferrite core.
Cables not included.
Please purchase the necessary cables at your local store.
11
EN
I
NITIAL SETTING
WATCHING TVINTRODUCTION PREPARATION
INITIAL SETTING
OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
Initial Setup
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1
After making all the necessary connections,
press [POWER] to turn on the unit.
• This operation may take a few moments.
2
Use [Cursor
K
/
L
] to select the on-screen language
from the choices on the right side of the TV screen.
(ENGLISH / ESPAÑOL / FRANÇAIS)
or
SELECT LANGUAGE
SELECCIONE EL IDIOMA
CHOISIR LA LANGUE
ENGLISH
ESPAÑOL
FRANÇAIS
SET
:
ENTER
AJUSTE
:
ENTER
VALIDER
:
ENTER
SELECT
:
K
,
, L
SELECCIONE
:
K
,
, L
CHOIX
:
K
,
, L
• “INITIAL SETUP“ menu on step 3 will be displayed in
the selected language after you press [ENTER].
3
Use [Cursor
K
/
L
] to select “AUTO PRESET CH(TV/DTV)”
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [ENTER].
or
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
- INITIAL SETUP -
• Scanning and memorizing the channels automatically
start.
25
AUTO PRESET CH(TV/DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
5
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during “AUTO PRESET CH”,
this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SETUP” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 12.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [SETUP].
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“HELPFUL HINTS” appears. Follow the instructions listed on
the TV screen.
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH”?
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
Main Menu
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
Press [SETUP].
e.g.) digital TV mode
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
PICTURE
You can adjust the picture quality.
(Refer to “Picture Adjustment” on page 19.)
CHANNEL SETUP
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 12.)
V-CHIP SETUP
You can set the viewing limitations.
(Refer to “V-chip” on page 23.)
LANGUAGE
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to “Language Selection” on page 12.)
CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to “Closed Caption” on page 19.)
5
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
12
EN
I
NITIAL SETTING
BACK LIGHT
You can set the desired brightness mode.
(Refer to “Back Light Setting” on page 22.)
COLOR TEMP.
You can adjust color temperature (“NORMAL”, “WARM”,
“COOL”).
(Refer to “Color Temperature” on page 22.)
DTVCC
In addition to the basic closed caption described
on page 18, DTV has its own closed caption called
DTVCC.
(Refer to “DTV Closed Caption” on page 20.)
PC SETTING
You can adjust the position, stability and clarity of the
PC screen.
This menu will appear only in PC mode, and can only
be set when the unit detects the PC input signal.
(Refer to “PC Settings” on page 26.)
Auto Channel Scan
If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a di erent area after the initial setting, or if you restore the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select “CHANNEL SETUP”,
then press [ENTER].
e.g.) digital TV mode
or
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
3
Use [Cursor K / L] to select your desired preset type,
then press [ENTER].
e.g.) digital TV mode
or
- CHANNEL SETUP -
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
• When aerial antenna is connected,
select “AUTO PRESET CH(TV)”, “AUTO PRESET CH(DTV)”
or “AUTO PRESET CH(TV/DTV)”.
• When connected to CATV, select
“AUTO PRESET CH (CATV)”.
5
• Scanning and memorizing the channels automatically
start.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH(TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
Note:
• If you connect the cable system directly, contact the CATV
installer.
•
If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
•
When no channel can be received by auto channel scan,
“NO TV SIGNALS” will be displayed on the TV screen.
•
Channel settings will be saved even if the power fails.
•
If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K / L] to select “IDIOMA”
or “LANGAGE”. Press [ENTER] to select “ENGLISH”. Press
[SETUP] to remove the main menu.
•
With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
Language Selection
You can choose English, Spanish, or French as your on-screen language.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select “LANGUAGE”,
then press [ENTER] repeatedly to change the setting.
e.g.) digital TV mode
or
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
ENGLISH
ESPAÑOL
FRANÇAIS
3
Press [SETUP] to exit.
5
13
EN
W
ATCHING TV
WATCHING TV
INTRODUCTION
PREPARATION INITIAL SETTING OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
Channel Selection
Select channels by using [CH.
K
/ L] or [the Number buttons].
Use
[CH.
K
/ L] or [the Number buttons] to select the
memorized channels.
or
or
Using [the Number buttons]
TV
- When selecting analog channel 12
DTV
- When selecting digital channel 12-1
• Be sure to press [–/ENT.] before entering the minor
channel number.
• Press [CH. RECALL ] to return to the previously
viewed channel.
• When you select a channel larger than 100, press
[+100] first. Then use [the Number buttons] to press
the lower 2-digit numbers.
• Only [the Number buttons] can be used to select the
non-memorized channels.
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple
signals to send simultaneously. Therefore, you can
select more than one program per major channel since
digital broadcasting technology distinguishes between
multiple channels broadcast by a single network.
CH4
CH4
(high denition TV)
18:00
18:30
19:00
19:30
20:00
20:30
CH4-1
CH4
CH4
No signal
No signal No signal
CH4-2
ATSC (digital mode)
CH4
NTSC (analog mode)
[Air Time]
No signal
CH4-1CH4 CH4-2
: change automatically
major channel
: change manually by using [CH. K/L]
minor channel
Note:
• “NO SIGNAL” will appear on the TV screen after the minor
channel broadcast is over.
5
Volume Adjustment
This section describes how to adjust the volume.
The mute function, which turns the sound off and on, is also described.
Use
[VOL.
X
/
Y
] to adjust the audio volume
.
or
VOLUME 20
• The volume bar will be displayed at the bottom of the
TV screen when adjusting the volume.
• The volume bar display will automatically disappear in
a few seconds.
Press [MUTE ] to turn off and on the sound.
MUTE 20
• “MUTE” is displayed on the TV screen for a few
seconds.
Press [MUTE ] again or use [VOL.
X
/
Y
] to recover
the original volume.
Switching Each Mode
You can easily switch with the remote control to the DTV (ATSC) and TV
(NTSC) or to access external devices when they are connected to the unit.
Press [INPUT] repeatedly to cycle through the input
modes.
ANALOG MODE
DIGITAL MODE
VIDEO1
VIDEO2
PC
• To use the video or S-video input jack on the unit,
select “VIDEO1”.
• To use the component video input jacks on the unit,
select “VIDEO2”.
• To use the PC input jack on the unit, select “PC”.
Note:
• When you switch the analog mode to the digital mode,
it may take a while until the digital channel selection is
completed. “NOW SCANNING“ is displayed while switching
the modes.
5
5
14
EN
W
ATCHING TV
Switching Audio Mode
This section describes how to switch the audio in the analog mode and how
to switch the audio language in the digital mode.
TV
While receiving an MTS broadcast, press [AUDIO ]
repeatedly to cycle through the available audio channel.
MAIN
SAP
MONO
MAIN : Outputs main-audio
SAP : Outputs second audio program
MONO : Outputs mono-audio
• The information display will automatically disappear
in a few seconds.
DTV
1
Press [AUDIO ] to display the currently selected
language and the number of available languages.
A Day of Memories
75 TV-PG ENGLISH 1/2
25-03
KABC
2
Press [AUDIO ] repeatedly to cycle through the
available audio languages.
• Available languages differ depending on the
broadcast. “OTHER” is displayed when the audio
language cannot be acquired, or the acquired
languages are other than English, Spanish or French.
• The information display will automatically disappear
in a few seconds.
Note:
• Pressing [AUDIO ] does not control external audio devices.
5
Sleep Timer
The sleep timer can be set to automatically turn o the unit after an
incremental period of time.
1
Press [SLEEP ] to set the sleep timer.
SLEEP OFF
• Sleep timer display appears on the TV screen.
2
Press [SLEEP ] repeatedly to change the amount of
time until shut off.
SLEEP 120MIN.
• You can set your unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each press of [SLEEP ] will increase the time by 30
minutes.
• After set up, the sleep timer display can be called up
for checking by pressing [SLEEP ].
To Cancel the Sleep Timer
Press [SLEEP
] repeatedly until “SLEEP OFF“ is
displayed on the TV screen.
Note:
• The sleep timer setting display will automatically disappear
in a few seconds.
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be canceled.
5
15
EN
WATCHING TV
INTRODUCTION
PREPARATION INITIAL SETTING OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
TV
In the analog mode, the current channel number is displayed.
Press [DISPLAY ].
CH 25
• The current channel number is displayed at the top-
right corner of the TV screen.
• To clear the display, press [DISPLAY ] again.
5
DTV
In the digital mode, the detailed broadcasting information for the current
channel such as program title, program guides are displayed.
Press [DISPLAY ] repeatedly to cycle through the
available display modes.
OFF
BROADCASTING INFORMATION
PROGRAM GUIDE
Broadcasting Information
The following information is displayed.
1 program title
2 signal quality indicator
3 program rating
4 channel number
5 broadcast station
6 audio language
(Refer to “Switching Audio Mode” on page 14.)
A Day of Memories
75 TV-PG ENGLISH 1/2
25-03
KABC
1
3
4
5
6
2
Program Guide
The program guide added to broadcasting information
is displayed.
A Day of Memories
75 TV-PG ENGLISH 1/2
25-03
KABC
A quarter-century ago, which may now
qualify as the good old days of newsp-
apering, run-of-paper sales accounted
for 80 percent of the industry’s adverti-
sing revenues.
program
guide
Note:
• When the program guide consists of more than 6 lines, use
[Cursor K / L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to VIDEO1 input
jack.
VIDEO 1
• The information display will automatically disappear in a
few seconds when the closed caption is on.
16
EN
W
ATCHING TV
TV Screen Display Mode
3-5 types of display modes can be selected when the broadcasting station
is sending 4:3 or 16:9 video signal or an external device is connected to the
unit. And 2 types of display modes can be selected for PC input signal.
Press [SCREEN MODE ] repeatedly to switch the TV
aspect ratio.
For 4:3 video signal
SIDEBAR
FULL
WIDE
(
analog / external input mode
)
MOVIE
WIDE
(digital mode)
: digital mode
: analo
g
/ external in
p
ut mode
SIDEBAR
Select to display a 4:3 picture at its original size.
The black bars appear on the left and right sides of the
screen.
FULL
Select to display a 4:3 picture to fill the screen.
MOVIE
¾available in the analog / external input mode only
Select to reduce the black bars on top and bottom.
WIDE
Digital mode:
Select to display a 4:3 picture to fill the screen and
shrink “FULL” picture horizontally.
Analog / external input mode:
Select to display a 4:3 picture to fill the screen and
stretch “FULL” picture horizontally.
5
For 16:9 video signal
FULL
SIDE CUT
EXPAND
MOVIE
ZOOM
: digital mode
: analo
g
/ external in
p
ut mode
FULL
Select to display a 16:9 picture to fill the screen.
SIDE CUT
Select to display a 16:9 picture to fill the screen and
stretch “FULL” picture horizontally. The left and right
sides of the picture will be cropped out.
ZOOM
¾available in the analog / external input mode only
Select to enlarge a 16:9 picture without distorting the
aspect ratio.
MOVIE
Select to reduce the black bars on top and bottom.
EXPAND
¾available in the analog / external input mode only
Select to reduce the black bars on the left and right
sides.
Note:
• You may not switch the display mode depending on the
program.
17
EN
WATCHING TV
INTRODUCTION
PREPARATION INITIAL SETTING OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
For PC input signal
Type of display Resolution
640 x 480 VGA
800 x 600 SVGA
1,024 x 768 XGA
Display a vertically stretched picture without distorting
the aspect ratio.
The black bars appear on the left and right sides of the
screen.
Type of display Resolution
848 x 480 WVGA
1,280 x 720
WXGA1,280 x 768
1,360 x 768
720 x 400 BIOS
Display a horizontally stretched picture without
distorting the aspect ratio.
The black bars appear on the top and bottom sides of
the screen.
Type of display Resolution
1,440 x 900
WXGA +
Display a picture in its original size.
Note:
• You can change the screen resolution on your PC.
18
EN
O
PTIONAL SETTING
Channel Add/Delete
The channel add/delete function lets you add the channel that was not
added by the auto channel scan due to the reception status at the initial
setting. You can also delete the unnecessary channels.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select “CHANNEL SETUP”,
then press [ENTER].
e.g.) digital TV mode
or
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
3
Use [Cursor K / L] to select “ADD/DELETE(DTV)” or
“ADD/DELETE”, then press [ENTER].
e.g.) digital TV mode
or
- CHANNEL SETUP -
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
4
Select the channel you want to add or delete.
(Refer to “Channel Selection“ on page 13.)
e.g.) digital TV mode
ADD/DELETE : DTV
D25
5
Use [Cursor s / B] to select “ADD” or “DELETE”.
or
• To add or delete another channels, repeat steps 4-5.
• Color of channel number displayed at the right top of
the TV screen indicates;
- Blue: The selected channel will be added.
- Red: The selected channel will be deleted.
5
6
Press [SETUP] to exit.
Note:
• ”ADD/DELETE(DTV)” or “ADD/DELETE” menu will disappear
automatically in a few seconds.
• In the digital mode (DTV), you can add or delete channels
only for major channel.
• Once you delete a DTV channel, you cannot recover the
channel without performing auto channel scan again.
(Refer to “Auto Channel Scan” on page 12.)
Loading...