Emerson SITETPI-E V3 User Manual

0 (0)
Emerson SITETPI-E V3 User Manual

SITETPI-E V3

Product Specification/Installation Sheet

Description

The Liebert SiteTPI-E is an Ethernetready device intended to interface specifically to a SiteScan Web system.

It is a 32-bit microprocessor-based device designed to monitor third-party equipment via an EIA-485/232 Modbus interface.

Logically the device sits on the Ethernet network, providing the interface to SiteScan Web. This effectively creates a router/gateway and third-party interface in a single device. Screw terminal blocks are provided to terminate power, communication and input signal wiring.

Module Dimensions and Layout

Ethernet port

BACnet port

Local access port

Rnet port Port S2

10/100 BaseT

Ethernet Port E1

100 LAN LINK

BACnet ®

Over ARCNET156 KBaud

BT485

 

Net +

 

 

Net -

BACnet

Shield

 

 

Local Access

Gnd

 

 

Rnet +

 

Rnet -

Rnet

 

 

+12V

 

Port S2

EIA-

Tx

485

232

 

Net+

Tx

 

Net-

Rx

 

n/c

DTR Rx

n/c

DCD

 

Signal Gnd

 

 

 

EIA-232

 

 

EIA-485

BT485

 

 

BACnet transmit BACnet receive

Archive Valid Port S1 transmit Port S1 receive

Battery low

11.295"

 

 

(286.9mm)

Power

0.23"

 

connector

(5.8mm)

 

Without Keypad Display:

 

 

24Vac, 24VA, 1A, 50-60 Hz

1.25"

 

26Vdc, 10W, 0.4A

 

Use Copper Conductors Only

 

Class 2

(32mm)

3V Lithium Battery

 

 

 

 

 

 

 

 

 

Ground

 

 

 

 

 

 

 

 

 

 

24V ac/dc

 

CR-123A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

 

 

 

 

 

 

On

Off

 

 

 

 

 

 

 

 

 

 

 

 

External

Gnd

2.5"

 

 

 

 

 

 

 

 

 

 

Battery

+3V

SiteTPI-E

 

 

 

 

Ext. Batt.

 

(64mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Int. Batt.

 

 

CONTROL MODULE

 

 

 

 

 

 

 

 

 

 

BT485

 

 

 

 

 

 

 

 

2 wire 4 wire EIA-232

 

7.5"

 

 

 

 

 

 

 

 

Signal Ground

 

 

 

 

 

 

 

 

 

n/c

Rx -

DCD

 

(190.5mm)

Open Energy

 

 

 

 

 

Port S1

n/c

Rx +

DTR

 

 

Management Equipment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Net-

Tx -

Rx

 

 

R

 

 

 

 

 

 

 

Net+

Tx +

Tx

 

2.5"

E143900

 

 

 

 

 

 

 

 

EIA-232

 

 

88FO

 

 

 

 

 

 

 

 

 

 

 

TYPE: 002001

 

 

 

 

 

 

 

EIA-485

 

 

(64mm)

Error Codes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chase = OK

 

 

 

 

 

 

 

 

485-2w

 

 

 

0 = Download required

Enhanced Access

 

 

 

 

 

 

 

 

 

 

 

 

 

485-4w

 

 

 

1 = Control Program Error

Port on S2

 

 

 

MSTP

PTP

 

 

 

 

2 = RAM full

and Rnet

 

IP Addr

Address

on S1

on S2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 = Comm setup error

On

Assigned

+100

Enable

Enable

 

 

 

 

 

4 = System error

 

 

 

 

 

 

 

 

 

 

 

 

8 = Formatting

Off

 

Default

0

Disable

Disable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Option

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Module

 

 

 

 

 

 

 

 

 

Comm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status Blinking Dot = 'Run'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Module

1.25"

Power

 

Address

LED

Format

10's 1's

(32mm)

 

 

 

 

Made in USA

Diagnostic

Port S1

Options

LED indicators

comm

 

1

Power Wiring Diagrams

Enclosure Dimensions

2

Loading...
+ 2 hidden pages