Liebert® PSA™
Quick-Start Guide - 1000VA/1500VA, 120V
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation and maintenance of the UPS.
•Intended for installation in a controlled environment.
•Maximum ambient temperature 104°F (40°C).
! CAUTION
To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in accordance with the national code, ANSI/NFPA 70.
•Do not connect equipment that may overload the UPS or demand half-wave rectification, such as a laser printer.
•Connect the UPS only to an earthed / grounded outlet that meets national and local electrical safety guidelines.
•Locate the UPS near a wall outlet. Do not use an extension cord between the UPS and the outlet.
•The Liebert PSA has been designed for small office/home office use only; it is NOT recommended for use in life-support applications.
•In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.
•Do not attach power strips or surge suppressors to the UPS.
•Do not attempt to service any parts inside the UPS except the batteries. Failure to adhere to this could cause personal injury or equipment malfunction and void the warranty.
•For technical support:
•Visit www.liebert.com or
•Send an e-mail to upstech@emersonnetworkpower.com.
Inspect the package and the UPS upon receipt. Notify the carrier and dealer of visible damage.
Liebert shutdown
software
CD
Quick-start
guide
USB cable
UPS
See figure at right for the location of the Site Wiring Indicator on the rear of the UPS.
•Check the rear of the UPS to make sure the Site Wiring Fault indicator is NOT illuminated.
Caution: If the Site Wiring Fault indicator is illuminated, have a qualified electrician check the wall receptacle wiring and fix any problems.
The UPS has three battery backup outlets that provide power when the UPS operates on battery (see Figure 2 below).
•Plug the loads into the battery backup outlets on the rear of the UPS.
Caution: Do not connect a laser printer to the
UPS.
USB |
SITE WIRING |
|
|
FAULT |
|
|
IN |
OUT |
Battery Power Supply |
Full Time Surge Protection |
|
AC OUTPUT |
|
|
AC INPUT |
|
|
The UPS must be placed indoors, protected from water, direct sunlight and excessive heat.
Provide at least 4" (100mm) of clearance on all sides of the unit for proper ventilation.
Step 3 Charge the UPS Battery Before
Use
The UPS battery is not charged before shipping. It MUST be charged before use.
• Connect the UPS power cord to a wall outlet and charge for at least eight hours.
Note: If battery is placed in storage, charge the battery every six months if kept at 5°F to 85°F (-15°C to 29°C)—or every three months if kept at 86°F (30°C) or higher.
After the battery is fully charged:
•Turn on the UPS by pressing the On/Off button (see Figure 1 below).
LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.
The UPS has two RJ-45 jacks for network lines (see |
|
|
|
|
Figure 2 below). |
RS232 |
USB |
SITE WIRING |
|
|
|
FAULT |
|
|
• Connect a single-line network cable into the RJ-45 |
|
|
IN |
OUT |
network surge protection IN jack on the rear of the |
|
|
|
|
UPS. |
Battery Power Supply |
Full Time Surge Protection |
||
|
|
AC OUTPUT |
|
|
• Connect an RJ-45 cable from the OUT jack on the |
AC INPUT |
rear of the UPS to a port on a PC or network device |
|
|
|
such as a router. |
|
To start using the Liebert shutdown software:
• Install the Liebert shutdown software. See the software user manual for installation instructions.
• Connect one end of the USB cable (supplied) to the USB port on the rear of the UPS. Connect the other end to a USB port on the computer. See the software user manual for operating instructions.
Figure 1 - Front Panel LEDs Figure 2 - Rear Panel
LED 1 LED 2 |
On/Off |
LED 3 |
LED 4 |
USB |
||||||||||||
(green) (amber) |
button |
(amber) |
(red) |
|||||||||||||
interface |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Utility |
|
|
|
! |
|
Fault |
Battery backup |
symbol |
|
|
|
symbol |
outlets (6) |
||
|
|
|
NEMA 5-15R |
||||
|
|
|
|
|
|
|
|
Battery |
|
|
|
Overload |
|
||
symbol |
|
|
|
symbol |
Input |
||
|
|
|
|
|
|
|
|
|
EMERSON |
|
Liebert |
|
breaker |
||
|
™ |
|
|
||||
|
|
Network Power |
® PSA |
|
|
||
|
|
|
AC Power System |
|
NEMA |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5-15P |
UPS Status, Alarm Conditions and Alerts
|
USB |
SITE WIRING |
|
|
|
FAULT |
|
|
|
IN |
OUT |
|
Battery Power Supply |
Full Time Surge Protection |
|
AC INPUT |
AC OUTPUT |
|
|
BREAKER |
|
|
|
AC INPUT |
|
|
|
Site Wiring Fault indicator
RJ-45 jacks (2) - network protection
Surge outlets (2) NEMA 5-15R
Condition |
LED |
Color |
Solid/Flashing |
Audible Alarm |
Normal Mode |
LED 1 |
Green |
Solid (steady glow) |
(None) |
Battery Mode |
LED 2 |
Amber |
Flashes every 3 seconds |
Every 3 seconds |
Battery Low |
LED 2 |
Amber |
Flashes every 1 second till end of discharge (EOD) |
Every 1 second |
Overload |
LED 3 |
Amber |
Solid (steady glow) until load drops or breaker trips |
Continuous |
Battery Replacement |
LED 4 |
Red |
Flashes every 1 second for 5 seconds only |
Every 1 second for 5 seconds only |
Fault |
LED 4 |
Red |
Solid (steady glow) until UPS shuts down after 5 seconds |
Continuous until UPS shuts down |