Electrolux WSB4650H, WSB4250H, WS4650H, WS4250H, WS4500H User Manual

Instruction handbook

Washer-extractors

WS4250H – WS4350H – WS4500H – WS4650H WSB4250H – WSB4350H – WSB4500H – WSB4650H

01201138/GB

14.10

.

INSTRUCTION HANDBOOK

		01201138	0907	0	0
	Table of contents
		Notice	Date	Page

Pages/Chapters
General instructions
General ...................................................	1/1
Precautions for use.................................	1/2
Environmental information ......................	1/3
Preliminary instructions...........................	1/4
Locking and tagging procedure ..............	1/5
Handling/Weight
Handling..................................................	1/6
Packing - Weight.....................................	1/7
Technical characteristics
Technical characteristics.........................	1/8
Sound level ............................................	17/8
Label of energetic performances ...........	17/8
Installation/Putting into service
Installation...............................................	1/9
Working place lighting.............................	2/9
Supplies ..................................................	2/9
Mechanical installation............................	3/9
Fitting of the safety fl anges.....................	4/9
Fitting of the fi lling angles .......................	5/9
Assembling of the partition for
barrier machine.......................................	6/9
Water connections ..................................	7/9
Steam connection ...................................	8/9
Indirect steam heating ..............................	9/9
Drain connection....................................	10/9
Air vent connection ................................	11/9
Installation of the gas exchanger ...........	11/9
Connection of the evacuation pipe of
the gas exchanger .................................	13/9
Gas connection......................................	15/9
Liquid detergents connection.................	22/9
Electrical connection..............................	25/9
Remove of the transport locks fi tted ......	30/9
Operating inspection
Manual operation ...................................	1/10
Automatic operation...............................	2/10
Machine operation
Auxiliary control ....................................	1/11
Automatic operation...............................	3/11
Detergent dispenser ..............................	5/11
To run a wash program ..........................	6/11
The "move back" key .............................	6/11
To start the wash program .....................	7/11
To start a wash program from the
program library......................................	10/11
To change parameters in the current
program step.........................................	13/11

Pages/Chapters

Rapid advance......................................	14/11
Show weight .........................................	15/11
Pause....................................................	17/11
Manual operation during a program......	18/11
Text .......................................................	24/11
To change the wash program after
program operation has commenced .....	25/11
To change temperature scale °C/ °F.....	26/11
Auto restart ...........................................	27/11
Manual operation
To select a manual operation................	28/11
Motor/door ............................................	29/11
Water/drain ...........................................	30/11
Heating .................................................	31/11
Detergent signals and water fl ushing....	32/11
At the end of the wash ..........................	33/11
Statistics
To select "statistics" ..............................	35/11
Resetting statistic registers...................	37/11
Automatic weighing
Scale adjustments ................................	42/11
ON/OFF and pause
On/off and pause by exterior signals ....	53/11
Memory card
General introduction .............................	54/11
To select the "Memory card" function....	55/11
To run a wash program straight from
a memory card .....................................	58/11
To copy a program from a memory card
to the machine's program control unit...	59/11
To copy a program from the program
control unit to a memory card ...............	61/11
To delete a program on a
memory card.........................................	63/11
To delete all programs on a
memory card.........................................	64/11
Weighing equipment ..............................	65/11
Safety
Safety.....................................................	1/12
Maintenance
Operating incidents................................	1/13
Preventive maintenance ........................	1/14
Electric diagrams
Electric diagrams ...................................	1/15
Appendices
Convertion measurement units..............	1/16
Washing symbols...................................	2/16

The manufacturer reserves the right to modify construction and equipment characteristics.

	01201138	0107	1	1	1. General	INSTRUCTION
	Notice	Date	Page
						HANDBOOK

General instructions

The machines described in this handbook have a washing capacity of 229, 338, 467 or 668 litres according to their type.

They are washer-extractors designed to meet the most severe requirements. They are designed to be installed in hotels, laundries, hospitals or collectivities.

The suspension device mounted with springs and shock absorbers limits to the maximum ground vibrations.

A important G factor guarantees the highest extraction quality for your linen.

These machines also exist in barrier version allowing the respect of linen's hygiene rules.

Identifi cation plate

GAS EXCHANGER

Adjustment label

D0630A/434

INSTRUCTION HANDBOOK

		01201138	0107	2	1
	1. General
		Notice	Date	Page

This washer extractor is controlled by a microprocessor-based program control unit placed on the loading side. There are many advantages to this equipment, including :

•Timing, levels and temperatures are controlled with great precision and fl exibility.

•The large display screen means that detailed information on wash programs, machine status and operations, wash times and temperatures can be accessed in plain language

•It is possible for the user to create new wash programs, and to adapt programs with great precision, on the basis of experience and to suit various types of textile, degrees of soiling etc.

•a very high level of machine safety through continuous monitoring and built-in safety interlocks.

•The program control unit has a reader for "smart cards". These are cards the size of a credit card which contain a memory chip. Smart cards allow the user to :

-transfer wash programs between a PC and the washer extractor, or from one washer extractor to another

-run programs straight from a card

•Great fl exibility during program operation :

-rapid advance both forwards and backwards in the program

-the user can change temperatures, program module lengths and extraction speeds directly, during program operation

-change to running a different wash program, at any time during program operation of the washer extractor.

RUN A WASH PROGRAM

GO TO THE MENU

MAKE YOUR CHOICE WITHOR PRESS SELECT

Display screen

WEIGHT, KG 000,0

SELECT

Numeric keyboard

Function keys.

The functions of these keys change, depending on which menu or part of a menu you are using. Their

current functions at any time are shown on the display immediately above each key.

Card reader for memory cards

During a wash : "Pause" key.

Before and after a wash, and during programming : "Move back key".

By pressing this key repeatedly you can move backwards through the menus you have navigated through. This will always bring you back to the menu shown on the display in this illustration.

4221A

	01201138	0107	3	1		INSTRUCTION
					1. General
	Notice	Date	Page
						HANDBOOK

A very high working safety level of the machine is achieved thanks to a continuous monitoring and built-in safety devices.

Even the compound textile fabrics can be washed at a high temperature with no crumpling risk thanks to a special cooling process before the rinsing cycle.

In order to avoid an excessive mechanical fatigue during the hydro-extraction process, the machine is equipped with an unbalance detector. If the latter detects the least unbalance of the load, the hydro-extraction cycle is interrupted and the machine fi lls with water to make a new distribution of the linen possible.

The machine then resumes the distribution speed and another hydro-extraction cycle begins.

The machine can also be controlled sequence by sequence and is equipped with a keyboard for the manual control of certain functions.

Note about the A.C. power

•According to the EN 60204-1:1997 standard, the machine is provided for AC supplies corresponding to the extracted caracteristics below :

4.3.2 AC supplies

Voltage:

Steady state voltage : 0,9…1,1 of nominal voltage.

Frequency:

0,99…1,01 of nominal frequency continuously. 0,98…1,02 short time.

Harmonics:

Harmonic distorsion not to exceed 10 % of the total r.m.s. voltage between live conductors for the sum of the second through to the fi fth harmonic. An additional 2 % of the total r.m.s. voltage between live conductors for the sum of the sixth through to the 30th harmonic is permissible.

Voltage unbalance:

Neither the voltage of the negative sequence component nor the voltage of the zero sequence component in three-phase supplies shall exceed 2 % of the positive sequence component.

Voltage interruption:

Supply interrupted or at zero voltage for not more than 3 ms at any random time in the supply cycle. There shall be more than 1s between successive interruptions.

Voltage dips:

Voltage dips shall not exceed 20 % of the peak voltage of the supply for more than one cycle. There shall be more than 1 s between successive dips.

INSTRUCTION HANDBOOK

		01201138	0107	1	2
	2. Precautions for use
		Notice	Date	Page

Precautions for use

•The machine should not be used by children.

•The machine is designed for "water washing" of textile only.

•This machine is for professional use and must be used exclusively by qualifi ed personnel.

•It is forbidden to wash textiles soaked with solvents.

•In case of a gas heated machine, do not assemble the machine on premises containing a dry cleaning machines or other similar machines.

•Make sure note to over load the machine.

•Please wash only items offering appropriate distribution inside the drum. Do not wash items such as mattresses or shoes.

Call our technical departments before washing non-standard items. Non compliance with these instructions may void the manufacturer's guarantee in case of abuse of the washer-extractor.

	01201138	0107	1	3	3. Environmental	INSTRUCTION
	Notice	Date	Page		information
						HANDBOOK

Environmental information

Concerned by providing the end user with useful and necessary environmental information, we wish to precise :

•Data about energetic consumptions, wastes (atmospheric and liquid) and sound level are indicated in the paragraph "Technical characteristics".

•The running of this machine requires the use of detergents which draining in the nature can have a signifi cant environmental impact. So, we do recommend to only use, with agreement of the manufacturers, the quantities of detergents strictly necessary.

•Forseeing its recycling, this machine is fully dismantle.

•This machine is free from any asbestos.

•Our machine packing complies with the provisions of rule 98-639 dated July 20th 1998 regarding environmental demands.

For additional information, do not hesitate to consult our environmental department.

INSTRUCTION HANDBOOK

	4. Preliminary	01201138	0107	1	4
	instructions	Notice	Date	Page

Preliminary instructions

Before any use, it is compulsory to read the instruction handbook.

Users must have learnt how the machine operates.

The identifi cation plate is placed on the left hand side of the machine.

In order to prevent any risk of fi re or explosion, fl ammable products should never be used to clean the machine.

Any repair or maintenance intervention should be carried out by qualifi ed personnel only.

Detergents used in laundry are particularly agressive. No stainless steel is able to resist their corrosive actions. Detergent dispenser must consequently be considered as wearing parts likely to be replaced.

Explanation of graphic symbols

A flash of lightning with an arrow at its end displayed inside an equilateral triangle, warns the user about the presence of uninsulated "dangerous current" sufficient in intensity to cause electrocution.

An exclamation mark inside an equilateral triangle offers the user important advice about usage, servicing and hazardous conditions.

This symbol warns the user that there are mechanisms inside the machine which can be dangerous. The protective housing must be in place during use.

This symbol warns the user of the presence of high temperatures which could cause severe burns. Some surfaces can reach close to 200 °C (392 °F).

	01201138	0107	2	4	4. Preliminary	INSTRUCTION
	Notice	Date	Page		instructions
						HANDBOOK

SAFETY

This machine should be installed in conformance to the health and safety regulations, and only used in a sufficiently aerated area.

Check the instructions before installing or using the machine.

SAFETY

The mechanical and electrical installation of the machine should only be done by qualified personnel.

CAUTION

Do not use the machine unless it is plugged into a correctly earthed power socket complying with standards in force.

CAUTION

For your personal safety, never use the machine without the protective housings.

CAUTION

Disconnect the machine electrical power supply before doing any repair or servicing work.

Disconnect all the sources of energy before any intervention on the machine.

Never try to open the drum door before the complete stop of the cage.

The safety devices of the drum door(s) should in no case be made inoperative.

The machines comply with the European Directive EMC (Electromagnetic Compatibility). They have been tested in laboratory and approved as such. It is so prohibited to add wires or non shielded electric cables in the cabinets, strands or cables' troughs.

Considering that the volume of the cage is superior to 150 liters, the standard kept for the electric part is the IN 60204.

INSTRUCTION HANDBOOK

	4. Preliminary	01201138	0107	3	4
	instructions	Notice	Date	Page

Ensure that the machine is not loaded beyond its nominal capacity (see "Specific load" in the instruction booklet’s technical characteristics).

An excessive load has consequences for the lifetime of the machine’s organs, as follows:

·Rapid destruction of the suspension elements (springs, shock absorbers);

·Excessive fatigue of motorisation elements (engine, belt);

·Rapid reduction of lifetime of drum bearings (rolling bearings);

·Opening and destruction of drum doors and tank doors during oil dehydration.

This is particularly important for your safety and that of others. The consequence is an immediate cancellation of the warranty.

The use and handling of chemical products such as detergent, chlorine, acids, antiliming agents etc... may create hazards for health and environment ; the following precautions should be taken.

-Do not breathe the dusts or steam.

-Avoid contact with skin or eyes (may cause burns).

-In case of important spillage, wear a protecting mask, gloves, and eye protectors.

-Handle with care.

-Consult the use and first aid advice on the packings.

-Do not dispose pure products in the environment.

The machine can work without the protective casing when the electric supply is not cut off.

Interlock the main isolating switch with a padlock.

Close the steam or gas inlet valves.

	01201138	0107	4	4	4. Preliminary	INSTRUCTION
	Notice	Date	Page		instructions
						HANDBOOK

Distributor Letter

Chemical System Responsibility

Disclaimer

The following policy should be considered and understood as a warranty/disclaimer to customers operating textile care installations where liquid supply (chemical) systems use or may use peristaltic pumps to inject supplies into equipment.

To Whom it May Concern :

We, the undersigned, accept no responsibility for loss or damage when, during periods of non-use, concentrated chemicals leak, spray or "dribble" onto any part of our machines or their contents.

It is well known that many pumped liquid chemical systems tend to permit concentrated chemicals to dribble out of the injection tubes when the system has not been used for relatively long periods of time – as after working hours and during weekends. This puts highly concentrated corrosive chemicals in direct contact with dry stainless steel surfaces and often directly on any textiles left in the machine. Chemical deterioration (rusting) of the stainless steel and damage to the textiles is the inevitable result.

It is absolutely useless to fl ush the affected sites after each injection because the harmful dribble always occurs later – after the machine is no longer in use. One seemingly foolproof solution for "dribbling chemicals" (which we highly recommend but obviously cannot guarantee) is to locate the chemical tanks and pumps well below the injection point on the machine (so the contents of the injection tube(s) cannot siphon into the machine) and to completely purge the just-used chemical injection tube(s), or manifold, with fresh water after every injection so that only fresh water (which cannot cause a problem) can dribble out. Naturally, this – or any other solution – is the sole responsibility of the pump and/or chemical supplier (not the machine manufacturer).

Additionally, external chemical leakage is dangerous to personal health and safety, and will also cause severe damage to machines and/or their surroundings. The installer and/or user of the chemical injection system must make sure there are no external chemical leaks and that excessive pressure can never build up in any chemical delivery tube, because excessive pressure can burst the tube, or disconnect it from the machine, and spray dangerous concentrated chemicals about the premises.

The machinery manufacturer is not, and cannot be, responsible for compliance with the above.

INSTRUCTION HANDBOOK

	5. Locking and	01201138	0107	1	5
	tagging procedure	Notice	Date	Page

Locking and tagging procedure

A red insert at the beginning of this instruction handbook schematically shows the locking and tagging procedure described below. If you wish, you can detach this insert and display it close to the machine to remind maintenance personnel of the safety instructions.

Alwaysrespectitems 1 2, 3 and 4 carefully before doing any repair or maintenance work on the ma-

chine.

Put the main switch 2 to Off and lock the handlewithapadlock in one of the three holes provided for

this purpose.

Close the stop valves for the other supplies (steam, gas, thermal fl uid, compressed air) to stop and lock their handle with a pad-

lock.

3	Open the fi xed	Do the maintenance.
	protectors (casings,
	doors) with the key
	provided or a special
	tool.
	Close and carefully
	lock the fi xed
	protectors.

4		Unlock	the	stop
		valves	and	the
		main switch.

	01201138	0107	1	6
	Notice	Date	Page
				6. Handling

INSTRUCTION HANDBOOK

Handling

Before any handling, check that the four transport locks fi tted are still in place and well-tightened.

To do so, remove the front and rear casings and check presence of four locks (B).

D0650A

SAFETY

It is obligatory that all these operations are undertaken by handling specialists.

1/ Lifting with handling straps

Lifting in that case can only be done with handling straps (minimum capacity 1000 daN) which bear weight of the machine.

Nota : in order to avoid bending of the machine's casings, make sure to place the lifting straps at each end of the wooden planks.

D0604A

INSTRUCTION HANDBOOK

		01201138	0107	2	6
	6. Handling
		Notice	Date	Page

CAUTION

You should never handle the machine in its longitudinal side (any other than shown on the drawing below) with a fork-lift truck.

Important risk of parts deterioration for those fixed under the machine.

2/ Lifting with a fork-lift truck

This can be carried out from the front or back, at the centre of the machine.

D0603A

3/ Ground moving

The machine frame is made up of two parallel parts, making ground moving possible by means of rollers.

D0659A

	01201138	0107	3	6		INSTRUCTION
					6. Handling
	Notice	Date	Page
						HANDBOOK

4/ Lifting with a jack

Lifting in this case can only be done with a jack (minimum capacity 500 daN) which can bear the machine's weight.

Nota : in order to avoid the bending of the sole, make sure to place the lifting jack at each corner of the machine at point A or B.

B

A

CAUTION

In order to avoid any bending of casings, you should never climb and stand on top of the machine.

B

AD0671A

INSTRUCTION HANDBOOK

7. Packing - Weight

	01201138	0107	1	7
	Notice	Date	Page

Packing

Packing dimensions in mm/inch	Size A	Size B	Size C
Washer extractor Type 250 standard	1180/46.5	1230/48.4	1840/72.4
Washer extractor Type 250 barrier	1180/46.4	1230/48.4	1840/72.4
Washer extractor Type 350 standard	1180/46.4	1450/57	1840/72.4
Washer extractor Type 350 barrier	1180/46.4	1450/57	1840/72.4
Washer extractor Type 500 standard	1180/46.4	1760/69.3	1840/72.4
Washer extractor Type 500 barrier	1180/46.4	1760/69.3	1840/72.4
Washer extractor Type 650 standard	1180/46.4	2180/85.8	1840/72.4
Washer extractor Type 650 barrier	1180/46.4	2180/85.8	1840/72.4

Weight

Weight in kg/lb (machine + crate)	Gas	Electric	Steam/T.F
Washer extractor Type 250 standard	775/1709	775/1709	775/1709
Washer extractor Type 250 barrier	775/1709	775/1709	775/1709
Washer extractor Type 350 standard	890/1963	890/1963	890/1963
Washer extractor Type 350 barrier	890/1963	890/1963	890/1963
Washer extractor Type 500 standard	1090/2404	1090/2404	1090/2404
Washer extractor Type 500 barrier	1090/2404	1090/2404	1090/2404
Washer extractor Type 650 standard	1195/2636	1195/2636	1195/2636
Washer extractor Type 650 barrier	1195/2636	1195/2636	1195/2636

Identifi cation plate (for gas machine only)

Adjustment label

GAS

EXCHANGER

D0660/776

	01201138	1009	1	8	8.Technical	INSTRUCTION
	Notice	Date	Page		characteristics
						HANDBOOK

Washer extractor type 250 standard

Right view

Front view

Left view

Top view

Drain connection

07100081B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	2	8
	characteristics	Notice	Date	Page

Washer extractor type 250 standard					Diagram no. 07100081B
Heating		Gas		Electric	Steam	Thermic fluid
Characteristics	Ø cage	----		-----------------------	770 mm (30.31") -----------------
	Cage length	----		-----------------------	520 mm (20.47") -----------------
	Cage volume		-----------------------	229 dm³ (229 l) ------------------
	Specifi c load 1/10	----		-------------------------	22.9 kg (50.5 lb)	---------------
	(dry linen, ISO 9398-4)			450 x 400 mm (17.71x15.74")
	Opening cage doors (L x H) ---- -------------
	Opening drum door (L x H) ----- -------------			466 x 525 mm (18.34x20.67") ----------
Floor area		----		-----------------------	1 m² (10.76 sq. ft)	---------------
Net weight		----		-----------------------	670 daN (1478 lb)	---------------
Weight loaded (high level)		68----l		-----------------------68l	830 daN (1830 lb)	---------------68 l
Water volume, washing, low level					68 l
Water volume, washing, high level		137 l		137 l	137 l	137 l
Max dynamic load		----		----------------- F = 101 daN (222 lb) -----------------
Max transmitted floor load		----		------------------- 814 daN (1795 lb) -------------------
Max pressure transmitted to floor		----		------------------- 100 kPa -------------------------------
Spin efficiency		----		------------------------------	350 G -----------------------
Max. unbalance		----		-----------------------	3.6 kg (7.94 lb) ------------------
(L) Main switch to connect main cable		4x2.5 mm²		4x6 mm²	4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable				380 / 415 V 3+E ~ 50/60 Hz
Supply voltage		3.7---------kW
Installed electric power				21.7 kW	3.7 kW	3.7 kW
Installed heating power		40 kW		18 kW	-	-
Electric consumption for a normal cycle* 0.8 kWh/h				6 kWh/h	0.6 kWh/h	0.6 kWh/h
Heat loss		---------		----------3 % of installed heating power-------------
(G) Steam inlet	Standard : DN 20 (3/4" BSP)			Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure				600 kPa (87 psi)
	- Steam intantaneous fl ow rate at 600 kPa				72 kg/h
	- Seam consumption for a normal cycle*				12 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure		---		------------------------	50 kPa (7.25 psi)	---------------
Water supply maximum pressure		360---l		------------------------340 l	300 kPa (43.5 psi) -------------
Water consumption for a normal cycle*					340 l	340 l
Water consumption for an ECO cycle**		282 l		260 l	260 l	260 l
(K) Liquid detergents inlet				DN 20 (3/4" BSP)
(H1) Drain connection		---		------------------------	Ø 75 mm (3") --------------------
(H2) Double drain connection		---		------------------------	Ø 75 mm (3") --------------------
Maximum flow rate		----		--------------------------	240 l/min -----------------------
(I) Waste water collector		----		-------------------- DN 150 mm (6" BSP) --------------
(3 cm/m (3%) minimum slope)				Ø 60 mm (2.36 ")
(J) Air vent hole		----
(N') Thermic fluid inlet or indirect steam heating					DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating					DN 15 (1/2" BSP)
	- Maximum supply pressure					600 kPa
	- Installed calorifi c power					34400 kcal
	- Average calorifi c consumption					11500 kcal/h
	- Inner volume thermic fl uid exchanger					2,62 l
Gas inlet				DN 20 (3/4" BSP)
Combustion products evacuation				Ø 125 mm (5")
(S) Weighing equipment (optional)				Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
	- Min./max. compress air pressure -------------------			5,5/7 bar--------------------------------
	- Consumption	--------------------------------			10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	0408	3	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 350 standard

Right view

Front view

Left view

Top view	Drain connection

07100083B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	4	8
	characteristics	Notice	Date	Page

Washer extractor type 350 standard						Diagram n°. 07100083B
Heating			Gas		Electric	Steam	Thermic fluid
Characteristics	Ø cage		----	-----------------------		770 mm (30.31") -----------------
	Cage length		----	-------------------------		760 mm (30") -------------------
	Cage voume		-----------------------		338 dm³ (338 l) ------------------
	Specifi c load 1/10		----	-------------------------		33.8 kg (74.55 lb) -------------
	(dry linen, ISO 9398-4)				600 x 400 mm (23.62x15.74")
	Opening cage doors (L x H) ---- -------------
	Opening drum door (L x H) ----- -------------				616 x 525 mm (24.25x20.67") ----------
Floor area			----	--------------------	1.25 m² (13.45 sq. ft) --------------
Net weight			----	-----------------------		760 daN (1676 lb)	---------------
Weight loaded (high level)			101----l	----------------------	996 daN (2195 lb) --------------		101 l
Water, washing, low level					101 l	101 l
Water, washing, high level			202 l		202 l	202 l	202 l
Max dynamic load			----	-----------------	F = 155 daN (342 lb) ------------------
Max transmitted floor load			----	-------------------	800 daN (1764 lb) -----------------
Max pressure transmitted to floor			----	-------------------	120 kPa -------------------------------
Spin efficiency			----	------------------------------		350 G -----------------------
Max. unbalance			----	-----------------------		4.8 kg (10.58 lb) -----------------
(L) Main switch to connect main cable			4x2.5 mm²		4x16 mm²	4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable					380 / 415 V 3+E ~ 50/60 Hz
Supply voltage			4.8---------kW	----------------
Installed electric power					32 kW	4.8 kW	4.8 kW
Installed heating power			40 kW		27 kW	-	-
Electrical consumption for a normal cycle* 1.2 kWh/h					9.2 kWh/h	1 kWh/h	1 kWh/h
Heat loss			---------	----------	3 % of installed heating power--------------
(G) Steam inlet	Standard :	DN 20 (3/4" BSP)			Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure					600 kPa (87 psi)
	- Steam instantaneous fl ow rate at 600 kPa					108 kg/h
	- Steam consumption for a normal cycle*					18 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure			---	------------------------		50 kPa (7.25 psi) ---------------
Water supply maximum pressure			495---l	------------------------	470 l	300 kPa (43.5 psi) --------------
Water consumption for a normal cycle*						470 l	470 l
Water consumption for a ECO cycle**			415 l		395 l	395 l	395 l
(K) Liquid detergents inlet				DN 20 (3/4" BSP)
(H1) Drain connection			---	------------------------		Ø 75 mm (3") --------------------
(H2) Double drain connection			240 l/min---	------------------------	240 l/min	Ø 75 mm (3") --------------------	240 l/min
Maximum drain flow rate						240 l/min
(I) Waste water collector			----	--------------------	DN 150 mm (6" BSP) ---------------
(3 cm/m (3 %) minimum slope)					Ø 60 mm (2.36 ")
(J) Air vent hole			----	--------------------
(N') Thermic fluid inlet or indirect steam heating						DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating						DN 15 (1/2" BSP)
	- Maximum supply pressure.						600 kPa
	- Installed calorifi c power						34400 kcal
	- Average calorifi c consumption						12500 kcal/h
	- Inner volume thermic fl uid						2,62 l
Gas inlet				DN 20 (3/4" BSP)
Combustion products evacuation					Ø 125 mm (5")
(S) Weighing equipment (optional)					Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
	- Min./max. compress air pressure			-------------------	5,5/7 bar--------------------------------
	- Consumption		--------------------------------			10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	0408	5	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 500 standard

Right view

Front view

Left view

Top view

Drain connection

07100085B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	6	8
	characteristics	Notice	Date	Page

Washer extractor type 500 standard						Diagram no. 07100085B
Heating			Gas		Electric	Steam	Thermic fluid
Characteristics	Ø cage		----	-----------------------		770 mm (30.31") -----------------
	Cage length		----	-------------------------		1040 mm (41") -----------------
	Cage volume		-----------------------		467 dm³ (467 l) ------------------
	Specifi c load 1/10		----	-----------------------		46.7 kg (103 lb) ------------------
	(dry linen, ISO 9398-4)				2x450 x 400 mm (17.71x15.74")
	Opening cage doors (L x H) ---- ------------
	Opening drum door (L x H) ----- -------------				935 x 527 mm (36.81x20.74") ----------
Floor area			----	--------------------	1.52 m² (16.36 sq. ft) --------------
Net weight			----	-----------------------		920 daN (2028 lb)	---------------
Weight loaded (high level)			140----l	-----------------------	140 l	1247 daN (2750 lb) -------------
Water, washing, low level						140 l	140 l
Water, washing, high level			180 l		180 l	180 l	180 l
Max dynamic load			----	-----------------	F = 275 daN (606 lb) ------------------
Max transmitted floor load			----	-------------------	830 daN (1830 lb) -----------------
Max pressure transmitted to floor			----	-------------------	150 kPa -------------------------------
Spin efficiency			----	------------------------------		350 G -----------------------
Max. unbalance			----	-----------------------		5.5 kg (12.13 lb) -----------------
(L) Main switch to connect main cable			4x2.5 mm²		4x25 mm²	4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable					380 / 415 V 3+E ~ 50/60 Hz
Supply voltage			5.8---------kW	----------------
Installed electric power					42 kW	5.8 kW	5.8 kW
Installed heating power			40 kW		36 kW	-	-
Electrical consumption for a normal cycle* 1.5 kWh/h					11 kWh/h	1.2 kWh/h	1.2 kWh/h
Heat loss			---------	----------	3 % of installed heating power--------------
(G) Steam inlet	Standard :	DN 20 (3/4" BSP)			Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure					600 kPa (87 psi)
	- Steam instantaneous fl ow rate at 600 kPa					144 kg/h
	- Steam consumption for a normal cycle*					24.5 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure			---	------------------------		50 kPa (7.25 psi) ---------------
Water supply maximum pressure			638---l	------------------------	610 l	300 kPa (43.5 psi) --------------
Water consumption for a normal cycle*						610 l	610 l
Water consumption for an ECO cycle**			558 l		530 l	530 l	530 l
(K) Liquid detergents inlet				DN 20 (3/4" BSP)
(H1) Drain connection			---	------------------------		Ø 75 mm (3") --------------------
(H2) Double drain connection			240 l/min---	------------------------	240 l/min	Ø 75 mm (3") --------------------	240 l/min
Maximum drain flow rate						240 l/min
(I) Waste water collector			----	--------------------	DN 150 mm (6" BSP) ---------------
(3 cm/m (3 %) minimum slope)					Ø 60 mm (2.36 ")
(J) Air vent hole			----	--------------------
(N') Thermic fluid inlet or indirect steam heating						DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating						DN 15 (1/2" BSP)
	- Maximum supply pressure						600 kPa
	- Installed calorifi c power						47300 kcal
	- Average calorifi c consumption						13800 kcal/h
	- Inner volume thermic fl uid						5,33 l
Gas inlet				DN 20 (3/4" BSP)
Combustion products evacuation					Ø 125 mm (5")
(S) Weighing equipment (optional)					Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
	- Min./max. compress air pressure			-------------------	5,5/7 bar--------------------------------
	- Consumption		--------------------------------			10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	1009	7	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 650 standard

Right view

Front view

Left view

Top view

Drain connection

07100087B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	8	8
	characteristics	Notice	Date	Page

Washer extractor type 650 standard					Diagram no. 07100087B
Heating			Gas	Electric	Steam	Thermic fluid
Characteristics	Ø cage		----	-----------------------	770 mm (30.31") -----------------
	Cage length		----	-------------------------	1500 mm (59") -----------------
	Cage volume		-----------------------	668 dm³ (668 l) ------------------
	Specifi c load 1/10		----	-----------------------	66.8 kg (147.33 lb) --------------
	(dry linen, ISO 9398-4)			2x600 x 400 mm (23.62x15.74")
	Opening cage doors (L x H) ---- ------------
	Opening drum door (L x H) -----			---------- 2x616 x 525 mm (24.25x20.66") ---------
Floor area			----	-------------------- 2 m² (21.53 sq. ft) ------------------
Net weight			----	-----------------------	1080 daN (2381 lb) ---------------
Weight loaded (high level)			200----l	-----------------------1547 daN (3410 lb) --------------
Water, washing, low level				200 l	200 l	200 l
Water, washing, high level			400 l	400 l	400 l	400 l
Max dynamic load			----	----------------- F = 466 daN (1028 lb) ----------------
Max transmitted floor load			----	-------------------- 811 daN (1788 lb) ----------------
Max pressure transmitted to floor			----	-------------------- 187 kPa ------------------------------
Spin efficiency			----	------------------------------	350 G -----------------------
Max. unbalance			----	-----------------------	8 kg (17.65 lb) -------------------
(L) Main switch to connect main cable			4x2.5 mm²	4x35 mm²	4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable				380 / 415 V 3+E ~ 50/60 Hz
Supply voltage			7.8---------kW
Installed electric power				61.5 kW	7.8 kW	7.8 kW
Installed heating power			40 kW	54 kW	-	-
Electrical consumption for a normal cycle* 2 kWh/h				23 kWh/h	2 kWh/h	2 kWh/h
Heat loss			---------	----------3 % of installed heating power--------------
(G) Steam inlet	Standard :	DN 20 (3/4" BSP)		Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure				600 kPa (87 psi)
	- Steam instantaneous fl ow rate at 600 kPa				216 kg/h
	- Steam consumption for a normal cycle*				24.5 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure			---	------------------------	50 kPa (7.25 psi) ---------------
Water supply maximum pressure			977---l	------------------------977 l	300 kPa (43.5 psi) --------------
Water consumption for a normal cycle*					977 l	977 l
Water consumption for an ECO cycle**			782 l	782 l	782 l	782 l
(K) Liquid detergents inlet				DN 20 (3/4" BSP)
(H1) Drain connection			---	------------------------	Ø 75 mm (3") --------------------
(H2) Double drain connection			240 l/min---	------------------------240 l/min	Ø 75 mm (3") --------------------	240 l/min
Maximum drain flow rate					240 l/min
(I) Waste water collector			----	-------------------- DN 150 mm (6" BSP) ---------------
(3 cm/m (3 %) minimum slope)				Ø 60 mm (2.36 ")
(J) Air vent hole			----
(N') Thermic fluid inlet or indirect steam heating					DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating					DN 15 (1/2" BSP)
	- Maximum supply pressure					600 kPa
	- Installed calorifi c power					47300 kcal
	- Average calorifi c consumption					15800 kcal/h
	- Inner volume thermic fl uid					5,33 l
Gas inlet				DN 20 (3/4" BSP)
Combustion products evacuation				Ø 125 mm (5")
(S) Weighing equipment (optional)				Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
	- Min./max. compress air pressure			-------------------5,5/7 bar--------------------------------
	- Consumption		--------------------------------		10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	0408	9	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 250 barrier

Right view

Front view

Left view

Top view

Drain connection

07100082B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	10	8
	characteristics	Notice	Date	Page

Washer extractor type 250 barrier							Diagram no. 07100082B
Heating			Gas		Electric		Steam	Thermic fluid
Characteristics	Ø cage		---------------------		770 mm (30.31") ---------------------
	Cage length		---------------------		520 mm (20.47") -------------------
	Cage volume		----------------------		229 dm³ (229 l) ---------------------
	Specifi c load 1/10		--------------------		22.9 kg (50.5 lb) -------------------
	(dry linen, ISO 9398-4)				450 x 400 mm (17.71x15.74")
	Opening cage doors (L x H) -----------
	Opening drum door (L x H) -----------				466 x 525 mm (18.34x20.67") -------------
Floor area			-------------------		1 m² (10.76 sq. ft) -------------------
Net weight			---------------------		670 daN (1478 lb) -------------------
Weight loaded (high level)			68---------------------l		830 daN (1830 lb) -------------------			68 l
Water, washing, low level					68 l		68 l
Water, washing, high level			137 l		137 l		137 l	137 l
Max dynamic load			----------------------		F = 101 daN (222 lb) -------------------
Max transmitted floor load			-----------------------		814 daN (1795 lb) ---------------------
Max pressure transmitted to floor			-----------------------		100 kPa ----------------------------------
Spin efficiency			-------------------------------			350 G -----------------------------
Max. unbalance			-----------------------------		3.6 kg (7.94 lb) -------------------
(L) Main switch to connect main cable			4x2.5 mm²		4x6 mm²		4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable					380 / 415 V 3+E ~ 50/60 Hz
Supply voltage			3.7---------kW	----------------
Installed electric power					21.70 kW		3.7 kW	3.7 kW
Installed heating power			40 kW		18 kW		-	-
Electrical consumption for a normal cycle* 0.8 kWh/h					5.3 kWh/h		0.6 kWh/h	0.6 kWh/h
Heat loss			---------	----------	3 % of installed heating power--------------
(G) Steam inlet	Standard :	DN 20 (3/4" BSP)			Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure						600 kPa (87 psi)
	- Steam instantaneous fl ow rate at 600 kPa						72 kg/h
	- Steam consumption for a a normal cycle*					12 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)				DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure				----------------------	50 kPa (7.25 psi) -----------------
Water supply maximum pressure			360 l	----------------------	300 kPa (43.5 psi) ----------------			340 l
Water consumption for a normal cycle*					340 l		340 l
Water consumption for an ECO cycle**			282 l		260 l		260 l	260 l
(K) Liquid detergents inlet				DN 20 (3/4" BSP)
(H1) Drain connection				-------------------------			Ø 75 mm (3") -------------------
(H2) Double drain connection			240 l/min	-------------------------	240 l/min		Ø 75 mm (3") -------------------	240 l/min
Maximum drain flow rate							240 l/min
(I) Waste water collector				---------------------	DN 150 mm (6" BSP) -------------
(3 cm/m (3 %) minimum slope)						Ø 60 mm (2.36")
(J) Air vent hole				------------------------
(N') Thermic fluid inlet or indirect steam heating							DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating							DN 15 (1/2" BSP)
	- Maximum supply pressure							600 kPa
	- Installed calorifi c power							34400 kcal
	- Average calorifi c consumption							11500 kcal/h
Gas inlet	- Inner volume thermic fl uid			DN 20 (3/4" BSP)				2,62 l
Combustion products evacuation					Ø 125 mm (5")

(O)Barrier partition (provided by customer)

(P)Frame 60x100 mm maxi (provided by customer)

(R)Aseptis seal

(S) Weighing equipment (optional)	Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
- Min./max. compress air pressure -------------------	5,5/7 bar--------------------------------
- Consumption --------------------------------	10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	0408	11	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 350 barrier

Right view

Front view

Left view

Top view

Drain connection

07100084B

INSTRUCTION HANDBOOK

	8.Technical	01201138	0208	12	8
	characteristics	Notice	Date	Page

Washer extractor type 350 barrier					Diagram no. 07100084B
Heating		Gas		Electric	Steam	Thermic fluid
Characteristics	Ø cage	---------------------		770 mm (30.31") ------------------
	Cage lenght	-----------------------		760 mm (30") -------------------
	Cage volume	----------------------		338 dm³ (338 l) -------------------
	Specifi c load 1/10	------------------------			33.8 kg (74.55 lb) --------------
	(dry linen, ISO 9398-4)			600 x 400 mm (23.62x15.74")
	Opening cage doors (L x H) --------------
	Opening drum door (L x H) ---------------			616 x 525 mm (24.25x20.67") ------------
Floor area		------------------		1.25 m² (13.45 sq. ft) ----------------
Net weight		---------------------		760 daN (1676 lb) -----------------
Weight loaded (high level)		101 l--------------------		996 daN (2195 lb) ----------------		101 l
Water, washing, low level				93 l	101 l
Water, washing, high level		202 l		202 l	202 l	202 l
Max dynamic load		--------------------		F = 155 daN (342 lb)		--------------
Max transmitted floor load		----------------------		800 daN (1764 lb) --------------
Max pressure transmitted to floor		----------------------		120 kPa ----------------------------
Spin efficiency		-----------------------------			350 G ------------------------
Max. unbalance		------------------------			4.8 kg (10.58 lb) ----------------
(L) Main switch to connect main cable		4x2.5 mm²		4x16 mm²	4x2.5 mm²	4x2.5 mm²
(M) Electric cable (section)
(N) or (N') Stuffing box for main cable				380 / 415 V 3+E ~ 50/60 Hz
Supply voltage		4.8---------kW	----------------
Installed electric power				32 kW	4.8 kW	4.8 kW
Installed heating power		40 kW		27 kW	-	-
Electrical consumption for a normal cycle* 1.2 kWh/h				9.2 kWh/h	1 kWh/h	1 kWh/h
Heat loss		---------	----------	3 % of installed heating power--------------
(G) Steam inlet	Standard : DN 20 (3/4" BSP)			Low pressure : DN 25 (1" BSP)
	- Maximum supply pressure				600 kPa (87 psi)
	- Steam instantaneous fl ow rate at 600 kPa				108 kg/h
	- Steam consumption for a normal cycle*				18 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option)			DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure			----------------------	50 kPa (7.25 psi) -----------------
Water supply maximum pressure		495 l	---------------------	300 kPa (43.5 psi) -----------------		470 l
Water consumption for a normal cycle*				470 l	470 l
Water consumption for an ECO cycle**		315 l		395 l	395 l	395 l
(K) Liquid detergents inlet			DN 20 (3/4" BSP)
(H1) Drain connection			-------------------------		Ø 75 mm (3") -------------------
(H2) Double drain connection		240 l/min	-------------------------	240 l/min	Ø 75 mm (3") -------------------	240 l/min
Maximum drain flow rate					240 l/min
(I) Waste water collector		---------------------		DN 150 mm (6" BSP) -------------
(3 cm/m (3 %) minimum slope)					Ø 60 mm (2.36")
(J) Air vent hole		------------------------
(N') Thermic fluid inlet or indirect steam heating					DN 15 (1/2" BSP)
(G) Thermic fluid return or indirect steam heating					DN 15 (1/2" BSP)
	- Maximum supply pressure					600 kPa
	- Installed calorifi c power					34400 kcal
	- Average calorifi c consumption					12500 kcal/h
	- Inner volume thermic fl uid					2,62 l
Gas inlet			DN 20 (3/4" BSP)
Combustion products evacuation				Ø 125 mm (5")

(O)Barrier partition (provided by customer)

(P)Frame 60x100 mm maxi (provided by customer)

(R)Aseptis seal

(S) Weighing equipment (optional)	Ø 4/6 mm
Compressed air inlet (low pressure steam) ---------------------------
- Min./max. compress air pressure -------------------	5,5/7 bar--------------------------------
- Consumption --------------------------------	10 l/h-----------------------------

* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min, extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).

** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.

	01201138	0408	13	8	8.Technical
	Notice	Date	Page		characteristics

INSTRUCTION HANDBOOK

Washer extractor type 500 barrier

Right view

Front view

Left view

Top view

Drain connection

07100086B