SbA750 User Manual
Electro-Voice®
Important Safety Instructions
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on this apparatus.
6.Clean only with a dry cloth.
7.Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9.Only use attachments/accessories specified by the manufacturer.
10.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
11.To completely disconnect AC power from this apparatus, the power supply cord must be unplugged.
For US and CANADA only:
Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrican for replacement of the absolete outlet.
Important Service Instructions
CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
1.Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSA E65 - 94 have to be obeyed when servicing the appliance.
2.Use of a AC separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is connected to the AC.
3.Switch off the power before retrofitting any extensions, changing the AC voltage or the output voltage.
4.The minimum distance between parts carrying AC voltage and any accessible metal piece (metal enclosure), respectively between the AC poles has to be 3 mm and needs to be minded at all times.
The minimum distance between parts carrying AC voltage and any switches or breakers that are not connected to the AC (secondary parts) has to be 6 mm and needs to be minded at all times.
5.Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original parts.
6.Altering the circuitry without prior consent or advice is not legitimate.
7.Any work security regulations that are applicable at the location where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations about the work place itself.
8.All instructions concerning the handling of MOS - circuits have to be observed.
Electro-Voice®
Table of Contents |
|
0 Introduction .............................................................................................................................................................. |
1 |
Unpacking and Warranty ............................................................................................................................... |
1 |
Setup and Connections ................................................................................................................................. |
1 |
1 Quick Start ............................................................................................................................................................... |
2 |
2 Controls ................................................................................................................................................................... |
3 |
Input L/Mono Input R ..................................................................................................................................... |
3 |
Parallel Outputs L/R ....................................................................................................................................... |
3 |
Mid-High Outputs L/R .................................................................................................................................... |
3 |
Level .............................................................................................................................................................. |
3 |
Status Indicators ............................................................................................................................................ |
4 |
Power Switch ................................................................................................................................................. |
4 |
AC Fuse ........................................................................................................................................................ |
4 |
AC Connector ................................................................................................................................................ |
4 |
3 Cabling .................................................................................................................................................................... |
5 |
4 Setup Example A ..................................................................................................................................................... |
6 |
5 Setup Example B ..................................................................................................................................................... |
7 |
6 Setup Example C ..................................................................................................................................................... |
8 |
7 Setup Example D ..................................................................................................................................................... |
9 |
8 Setup Example E ................................................................................................................................................... |
10 |
9 Specifications ......................................................................................................................................................... |
11 |
10 Dimensions ........................................................................................................................................................... |
11 |
11 Block Diagram ..................................................................................................................................................... |
12 |
Electro-Voice® |
TOC |
0. Introduction
Congratulations! In buying an Electro-Voice® SbA750 you decided on getting one of today’s most advanced active subwoofers incorporating sophisticated technology.
The active 15" subwoofer SbA750 with integrated 750 watt power amplifier has been specially designed to provide fundamental bass support for professional full-range and multi-channel cabinets. Through the integrated electronic frequency crossover of the SbA750 setting up an active stereo multi-channel system is truly simple. The stereo audio signals for the mid-high range cabinets are provided via the MID-HIGH outputs on the SbA750. Additionally provided are all connection facilities for using the SbA750 as active mono subwoofer in active 2-way or “add-on operation”. Manufactured from baltic birch and housing a highperformance Electro-Voice® DL15Y woofer, the SbA750 withstands even the hardest strain during transport and operation. While input connection is also possible via phone type jacks, all input and output signals are output via professional XLR-type connectors. The integrated High-Efficiency 750W power amplifier optimally matches the DL15Y woofer offering highest dynamic and audio performance and ensures at the same time that the DL15Y woofer is always operated in its optimum operation range. Extensive protection circuitry like VCP, DC/HF-protection, audio limiter, Back-EMF protection and thermal protection are employed to securely monitor the compliance to these operation limits guaranteeing that the SbA750 provides outstanding performance even under most demanding conditions. The SbA750 is also especially suitable for many rental applications. Compared to Class-AB-operated amps and because of utilizing Class-H HighEfficiency technology the power amplifier produces significantly less power loss, and additionally reduces thermal stress of all components. Employing fans to ensure thermal stability is not necessary because of the Class-H technology and use of comprehensively dimensioned cooling profiles. The enclosure is sealed with extremely durable Futura coating and a robust powder-coated steel grille provides protection for the Electro-Voice® DL15Y woofer against mechanical damage. All controls and the cooling profiles of the power amp module are recessed to provide optimum protection for the sensitive parts of the SbA750 even during transportation. Two carrying handles, four castors and an integrated threaded pole-mount stand flange allow comfortable transportation and optimum, space saving installation. Because of its versatility, the SbA750 can be easily integrated into any existing sound reinforcement installation.
Unpacking and Warranty
Open the packing and carefully take out the SbA750. Remove the protective foil from the carrying handles. A power cord and the warranty card are supplied in addition to this owner’s manual. Please make sure that all details are filled in on the warranty card. Only a completely filled in warranty certificate entitles you to stake any warranty claims. Therefore, keep the original invoice together with the warranty certificate at a safe place.
Setup and Connections
Place the SbA750 on an even ground if possibly by using the supplied rubber feet to ensure safe operation. Make sure to check the stability of the system when using pole-mount stands. Do not cover the heat sink on the subwoofer’s rear during operation. Otherwise, the SbA750 will enter protection mode because of thermal overload. Although this provides reliable protection for the subwoofer, sound reproduction is muted until the normal operation mode is regained. AC power is supplied via the Neutrik’s professional “PowerCon” connector system and by use of an 15’ (5m) AC cord. This ensures an absolute secure and reliable power supply connection. However, with large installations consisting of several active cabinets, the use of high-quality AC distributors that allow high power consumption and offer reliable protection throughout the entire system is strongly recommended.
Before establishing the AC connection for the first time, make sure that the SbA750’s operation voltage setting, which can be found on a label next to the AC switch, corresponds to your local AC voltage.
1 |
Electro-Voice® |
1. Quick Start
Caution: Before switching on the power of the SbA750 always set the LEVEL control to its counterclockwise stop. A playing sound source could otherwise lead to extreme
output levels.
This Quick Start Manual outlines the set up and operation of a SbA750 used as add-on subwoofer together with a Powermixer (see configuration examples). The operation procedures are equivalent for other mixers.
1.Set up your Powermixer system as usual and connect a signal source to the power mixer (e.g. CD Player or microphone).
2.Place your SbA750 somewhere between your full-range cabinets.
3.Set the SbA750’s LEVEL control to its counterclockwise stop and connect the unit to a wall outlet using the supplied PowerCon mains cord.
4.Use a stereo phone plug cable to connect the Powermixer’s MONO OUT to the SbA750’s L/MONO INPUT.
5.Move the Mixer MONO OUT fader all the way down.
6.Be sure to switch on the Mixer first and then the SbA750.
Switching on the SbA750 last is recommended. Otherwise, unwanted power-on noise might occur. When switching off your equipment, please proceed in the opposite order, i.e. switch off the SbA750 first.
7.Set the SbA750’s LEVEL control to its center position (0dB) and start the playback of the desired signal audio source.
8.After adjusting the desired acoustic output level of the full-range cabinets using the Powermixer’s master fader, establish volume setting for the subwoofer using the MONO OUT fader.
Electro-Voice® |
2 |
Loading...