Operator's Manual
SHRED 'N' VAC®
MODEL Type 1E ES-2100
Serial Number 001001 & Up
SHRED 'N' VAC PLUS™
MODEL Type 1E ES-2400
Serial Number 001001 & Up
WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
WARNING DANGER
Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood for proper and safe operation.
X7501135201 |
89861009662 |
|
10/99 |
||
|
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages.
THE OPERATOR'S MANUAL
Read and understand this manual before operation. Keep it in a safe place for future reference. It contains specifications and information for operation, starting, stopping, maintenance, storage and assembly specific to this product.
TABLE OF CONTENTS |
|
|
Introduction ............................................................... |
2 |
|
- |
The Operator's Manual ....................................... |
2 |
Manual Safety Symbols and Important Information .. |
3 |
|
Safety ......................................................................... |
3 |
|
- |
General Description ............................................ |
3 |
- |
Decals ................................................................. |
4 |
- |
International Symbols ......................................... |
5 |
- |
Equipment ........................................................... |
5 |
- |
Fuel ..................................................................... |
5 |
- Personal Condition and Safety Equipment ......... |
6 |
|
- |
Safe Operation .................................................... |
7 |
- |
Extended Operation/Extreme Conditions ............ |
8 |
Description ................................................................ |
9 |
|
- |
Emission Control ................................................. |
9 |
- |
Contents ............................................................. |
9 |
- ES-2100/2400 Major Components ..................... |
10 |
|
Specifications ........................................................... |
11 |
|
Assembly ................................................................. |
12 |
|
- |
Blower Application ........................................... |
12 |
- |
Vacuum/Shredding Application ....................... |
12 |
Pre-Operation ........................................................... |
14 |
|
- |
Fuel ................................................................... |
14 |
Operation ................................................................. |
15 |
|
- |
Starting Cold Engine ......................................... |
15 |
- |
Starting Warm Engine ....................................... |
16 |
Copyright© 2003 By Echo, Incorporated |
|
|
All Rights Reserved. |
|
- |
Stopping Engine ............................................... |
17 |
- Operating SHRED 'N' VAC® .................................................... |
17 |
|
- |
Operating Blower .............................................. |
18 |
Maintenance ............................................................ |
19 |
|
- |
Skill Levels ........................................................ |
19 |
- |
Maintenance Intervals ...................................... |
20 |
- |
Air Filter ............................................................ |
21 |
- |
Fuel Filter .......................................................... |
21 |
- |
Spark Plug ......................................................... |
22 |
- |
Cooling System ................................................. |
22 |
- |
Exhaust System ................................................. |
23 |
- |
Shredder Blade .................................................. |
23 |
- |
Debris Bag ........................................................ |
24 |
- |
Carburetor Adjustment ..................................... |
24 |
Troubleshooting ...................................................... |
26 |
|
Storage ..................................................................... |
27 |
|
Servicing Information ............................................... |
28 |
|
- |
Parts .................................................................. |
28 |
- |
Service .............................................................. |
28 |
- ECHO Consumer Product Support .................... |
28 |
|
- |
Warranty Card .................................................. |
28 |
- Additional or Replacement Manuals ................ |
28 |
|
- |
SUP22203474Supplement ................................. |
29 |
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.
SHRED 'N' VAC® |
3 |
|
OPERATOR'S MANUAL |
||
|
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.
This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders.
The circle with the slash symbol means whatever is shown within the circle is prohibited.
IMPORTANT This enclosed message provides information necessary for the protection of the unit.
NOTE This enclosed message provides tips for use, care and maintenance of the unit.
SAFETY
GENERAL DESCRIPTION
IMPORTANT
See Description and Specification sections and Decals in this section for full description and illustration of power head, Shred 'N' Vac® and blower assembly.
HANDLE |
STOP |
SWITCH |
VACUUM PIPE
MUFFLER
SIDE HANDLE
RECOIL
STARTER
DEBRIS
BAG
4
DECALS
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
General Warning Decal |
SPANISH |
||||
-WARNING- |
|
ADVERTENCIA |
|||
-DANGER- |
|
|
|
|
|
Read and follow all safety |
|
|
PELIGRO |
||
Esta unidad puede ser |
|||||
precautions in the operator's |
|||||
peligrosa |
y producir |
||||
manual. Operators, helpers & |
lesiones |
|
personales |
||
bystanders can be severely |
graves si |
no se usa |
|||
en forma adecuada. Para |
|||||
injured by blown objects and |
|||||
reducir |
el riesgo |
||||
must wear specified ANSI |
delesionarse, |
los |
|||
Z87.1 eye protection. Always |
operadores, |
los |
|||
ayudantes y |
los |
||||
wear hearing protection when |
espectadores |
deben |
|||
operating. |
leer y |
comprender el |
|||
|
Manual |
Del Operador |
|||
|
que se |
entrega |
|||
|
escrito en |
español. |
WARNING DANGER
Rotating Blades. Interlock switch must be operational. Vacuum tubes and bag must be in place. When used as a blower, housing cover must be closed and secured.
GENERAL
WARNING
DECAL
ENGLISH TRANSLATION
WARNING
DANGER
This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's Manual, which is provided in Spanish.
SPANISH
DECAL
HOT
DECAL
SHRED 'N' VAC® |
5 |
|
OPERATOR'S MANUAL |
||
|
INTERNATIONAL SYMBOLS
Symbol form/shape |
Symbol |
Symbol form/shape |
Symbol |
description/application |
description/application |
||
|
|
|
|
|
"WARNING, SEE |
|
Hot |
|
OPERATOR'S |
|
|
|
|
Surface |
|
|
MANUAL |
|
|
|
|
|
|
|
|
|
|
|
Wear eyes, ears and |
|
Fuel and oil mixture |
|
head protection |
|
|
|
|
|
|
|
|
|
|
|
Finger Severing |
|
Emergency stop |
|
|
|
|
|
|
|
|
Symbol form/shape |
Symbol |
Symbol form/shape |
Symbol |
description/application |
description/application |
||
|
|
|
|
|
Carburetor adjustment |
|
Primer Bulb |
|
- High speed mixture |
|
|
|
|
|
|
|
|
|
|
|
Carburetor adjustment |
|
Ignition |
|
- Idle speed |
|
ON/OFF |
|
|
|
|
|
Carburetor adjustment |
|
|
|
- Low speed mixture |
|
|
|
|
|
|
EQUIPMENT
Before operation a complete check of the unit must be performed:
-Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
-Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.
Spark Arrestor Muffler
-The spark arrestor muffler controls the exhaust noise and prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler.
Parts
-Do not use Shred 'N' Vac® if any part is missing or damaged.
-Have repairs done only by an authorized ECHO Service dealer.
-Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.
ATTACHMENTS
AND
ACCESSORIES
FUEL
WARNING DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.
-Use an approved fuel container.
-DO NOT smoke near fuel.
-DO NOT allow flames or sparks near fuel.
-Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
-NEVER refuel a unit when the engine is HOT!
-NEVER refuel a unit with the engine running.
-DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
-Securely tighten fuel cap after refueling.
-Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
6
After Refueling;
-Wipe any spilled fuel from the unit.
-Move at least 3 M (10 ft.) from refueling location before starting.
After Use;
-DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.
3M (10 FT.)
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Power blower/Shred 'N' Vac® users risk injury to themselves and others if the power blower/Shred 'N' Vac® is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a blower/Shred 'N' Vac® .
Physical Condition
Your judgment and physical dexterity may not be good:
-if you are tired or sick,
-if you are taking medication,
-if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection meeting ANSI Z87.1 or CE requirements whenever you operate the blower/Shred 'N' Vac® .
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the blower/Shred 'N' Vac® handle. Gloves also reduce the transmission of machine vibration to your hands.
Breathing Protection
Wear a face mask to protect against dust.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
SHRED 'N' VAC® |
7 |
|
OPERATOR'S MANUAL |
||
|
Proper Clothing -
Wear snug fitting, durable protective clothing;
•Pants should have long legs, shirts with long sleeves.
•DO NOT WEAR SHORTS,
•DONOTWEARTIES,SCARVES,JEWELRY.
Wear sturdy protective safety shoes or boots with non-skid soles;
•DO NOT WEAR OPEN TOED SHOES,
•DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather -
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.
SAFE OPERATION
Determine Operation Area
-Provide all operators of this equipment with the Operator's Manual, and instructions for safe operation.
-Review area to be cleared. Look for potential hazards such as stones or metal objects.
-Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15M (50 ft.) while the blower/Shred 'N' Vac® is in use.
-Do not operate this product indoors or in inadequately ventilated
areas. |
15 m (50 ft.) |
-Take wind conditions into account: avoid open doors and windows.
-Start unit on ground with throttle at idle. Check that vacuum tube or blower pipe is not blocked by the ground or by any objects.
-Do not point blower or vacuum tube at people or animals.
Use Proper Clothing & Equipment
-Before starting the unit, equip yourself and any other person working within the 15M (50 ft.) Safety Zone with the required Protective Equipment and clothing.
Keep A Firm Grip
- Hold handle with fingers together encircling the handle.
Keep A Solid Stance
-Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not overreach.
-Do not perform Maintenance or Assembly procedures with engine running.
-Material fed into this machine must be shreddable - metal, rocks, bottles or other non-shreddable material will damage the machine and can result in serious personal injury.
8
Noise Control
-Follow local noise regulations on sound levels and hours of operations. Use only during appropriate hours.
-Never use a higher speed setting then necessary to perform a task. The higher the engine speed the louder the blower noise.
-Be a good neighbor.
Avoid Hot Surfaces
-During operation, the exhaust area may become very hot, too hot to touch. Avoid contact during and immediately after operation.
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers. The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown.
•Keep your body warm, especially the head, neck, feet, ankles, hands and wrists.
•Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking.
•Limit the hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.
•If you experience discomfort, redness and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following:
•Avoid using your wrist in a bent, extended or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.
•Take periodic breaks to minimize repetition and rest your hands.
•Reduce the speed and force with which you do the repetitive movement.
•Do exercises to strengthen the hand and arm muscles.
•Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented.
SHRED 'N' VAC® |
9 |
|
OPERATOR'S MANUAL |
||
|
DESCRIPTION
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
EMISSION CONTROL
The emission control system for this engine is EM (Engine Modification).
IMPORTANT ENGINE INFORMATION ENGINE FAMILY : TEH021UB24RA DISPLACEMENT : 21.2cc
THIS ENGINE MEETS U.S. EPA PHI AND 1995 -
1999 CALIFORNIA EMISSION REGULATIONS FOR
ULGE ENGINES. REFER TO OWNER’S MANUAL
FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
Emission Control Label located on the engine. (EXAMPLE ONLY, information on label varies by engine FAMILY).
CONTENTS
1 - Power Head
1 - Blower Pipe Assembly
1 - Shred 'N' Vac® Suction Tube
1 - Elbow, Pipe
1 - T-Wrench
1 - Bottle 2-Cycle Engine Oil
1 - Debris Bag
1 - Operator's Manual
1 - Warranty Registration Card
1 - ECHO Emissions and Warranty Statement
ELBOW