Dukane 8755G-RJ, 8912-RJ User Manual

Size:
8.85 Mb
Download

Portable LCD Projector

Model 8755G-RJ

8912-RJ

USER’S MANUAL

#070027

Projector

8755G-RJ/8912-RJ

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

WARNING Before using this product, please read the “Safety Guide” first. After reading, store in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.

NOTE • The information in this manual is subject to change without notice.

The manufacturer assumes no responsibility for any errors that may appear in this manual.

The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

Mac is registered trademarks of Apple Computer, Inc.

VESAand SVGA are trademarks of the Video Electronics Standard Association.

Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the properties of their respective owners.

1

Contents

Contents

About this manual. . . . . . . . . . 1 Contents . . . . . . . . . . . . . . . . . 2 Projector features. . . . . . . . . . 3

Preparations . . . . . . . . . . . . . . 3

Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . . . . . . . .3

Part names . . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . .4 Control panel. . . . . . . . . . . . . . . . . . .5 Rear panel. . . . . . . . . . . . . . . . . . . . .5 Remote control . . . . . . . . . . . . . . . . .6

Setting up . . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . .7 Connecting your devices. . . . . . . . .10 Connecting power supply . . . . . . . .12 Using the security bar and slot . . . .12

Remote control . . . . . . . . . . . 13

Putting batteries . . . . . . . . . . . . . . .13 About the remote control signal. . . .13 Changing the frequency of remote

control signal . . . . . . . . . . . . . . . . .14

Using as a

simple PC mouse & keyboard . . .14

Power on/off . . . . . . . . . . . . . 15

Turning on the power. . . . . . . . . . . .15 Turning off the power. . . . . . . . . . . .15

Operating . . . . . . . . . . . . . . . 16

Adjusting the volume. . . . . . . . . . . .16 Temporarily muting the sound . . . . .16 Selecting an input signal . . . . . . . . .16 Searching an input signal . . . . . . . .17 Selecting an aspect ratio. . . . . . . . .17 Adjusting the projector's elevator . .18 Adjusting the zoom and focus . . . . .18 Using the automatic adjustment feature . .19 Adjusting the position . . . . . . . . . . .19 Correcting the keystone distortions. .20 Using the magnify feature . . . . . . . .20 Freezing the screen. . . . . . . . . . . . .21 Temporarily blanking the screen . . .21 Using the menu function . . . . . . . . .22

EASY MENU. . . . . . . . . . . . . . 24

ASPECT, AUTO KEYSTONEEXECUTE, KEYSTONE, PICTURE MODE, BRIGHTNESS, CONTRAST, COLOR, TINT, SHARPNESS, WHISPER, MIRROR, RESET, FILTER TIME, LANGUAGE, Go toAdvanced Menu...

PICTURE menu . . . . . . . . . . . 26

BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP, COLOR, TINT, SHARPNESS, MY MEMORY

IMAGE menu . . . . . . . . . . . . . 29

ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE, H SIZE, AUTO ADJUST EXECUTE

INPUT menu . . . . . . . . . . . . . 31

PROGRESSIVE, VIDEO NR, COLOR SPACE, COMPONENT, VIDEO FORMAT,

FRAME LOCK, COMPUTER IN, RESOLUTION

SETUP menu . . . . . . . . . . . . . 34

AUTO KEYSTONEEXECUTE, KEYSTONE, WHISPER, MIRROR, VOLUME,

SPEAKER, AUDIO

SCREEN menu. . . . . . . . . . . . 36

LANGUAGE, MENU POSITION, BLANK,

START UP, MyScreen, MyScreen Lock, MESSAGE, SOURCE NAME

OPTION menu . . . . . . . . . . . . 40

AUTO SEARCH, AUTO KEYSTONE,

AUTO ON, AUTO OFF, LAMP TIME,

FILTER TIME, MY BUTTON, SERVICE, SECURITY

NETWORK menu . . . . . . . . . . 51

DHCP, IP ADDRESS, SUBNET MASK, DEFAULTGATEWAY, TIME DEFFERENCE, DATE AND TIME, e-SHOT, INFORMATION, SERVICE

Maintenance . . . . . . . . . . . . . 54

Lamp . . . . . . . . . . . . . . . . . . . . . . . .54 Air filter . . . . . . . . . . . . . . . . . . . . . .56 Internal clock battery . . . . . . . . . . . .57 Other care . . . . . . . . . . . . . . . . . . . .58

Troubleshooting . . . . . . . . . . 59

Related messages. . . . . . . . . . . . . .59 Regarding the indicator lamps. . . . .60

Shutting the projector down. . . . . . .61 Resetting all settings . . . . . . . . . . . .61 Phenomena that may be easy

to be mistaken for machine defects. .62

Specifications . . . . . . . . . . . . 64 Network Guide . . . . . . . . . 1-35Technical Guide . . . . . . . .1-17Safety Guide . . . . . . . . . . .1-9

2

Projector features / Preparations

Projector features

This projector has a capability to project various picture signals onto a screen. This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance.

This projector boasts a variety of I/O port and low noise. These features provide you with the broad use of this projector.

Preparations

Contents of package

Please see the “Contents of package” section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens.

Fastening the lens cover

To avoid losing the lens cover, please fasten the

lens cover to the projector using the enclosed strap.

1. Fix the strap to the strap hole of the lens cover.

Thread one end of the strap through the strap hole

of the lens cover and make the loop at the end, and let the other end of the strap through the loop. Not have a knot in the strap at either end.

2. Fix the strap to the strap hole of the projector.

Thread the other end of the strap through the strap hole of the projector and make the loop there. Let the lens cover with the one end of strap though the loop.

Part names

Part names

Projector

HOT! (1)

(2) (3) (4)

(1)Lamp cover (54) The lamp unit is inside.

(2)Focus ring (18)

(3)Zoom ring (18)

(4)Control panel (5)

(5)Elevator buttons (x 2) (18)

(6)Elevator feet (x 2) (18)

(7)Remote sensor (13)

(8)Lens (18, 58)

(9)Lens cover (3)

(10)Intake vents

(11)Filter cover (56)

The air filter and intake vent are inside.

(12)Speaker (35)

(13)Exhaust vent

(14)AC inlet (12)

(15)Power switch (15)

(16)Rear panel (5)

(17)Security bar (12)

(18)Security slot (12)

(19)Slot cover (57)

The internal clock battery is inside.

(6)

 

 

 

(8)

 

 

(11)

(9)

 

(5)

(10)

(6)

(7)

(6)

 

 

 

 

 

 

(6)

 

 

 

(10)

HOT! (13)

 

 

(11)

(4)(12)

(19)

 

(18)

(14)

 

(16)

(15)

 

(17)

(1)

(13)

WARNING HOT! : Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes.

►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

CAUTION ►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air filter periodically.

►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

Part names

Control panel

(1)STANDBY/ON button (15)

(2)INPUT button (16, 22)

(3)MENU button (22)

It consists of four cursor buttons.

(4)POWER indicator (15, 60)

(5)TEMP indicator (60)

(6)LAMP indicator (60)

(6)

(5)

(4)

(1)(3) (2)

Rear panel

(1) AUDIO IN1 port (10)

 

 

(9) USB port (10)

(2) AUDIO IN2 port (10)

 

 

(10)

COMPONENT

(3) AUDIO OUT port (10)

 

 

 

(Y, Cb/Pb, Cr/Pr) port (10)

(4)

COMPUTER IN1 port (10)

 

 

(11) VIDEO port (10)

(5)

COMPUTER IN2 port (10)

 

 

(12)

S-VIDEOport (10)

(6)

MONITOR OUT port (10)

 

 

(13) AUDIO IN3 (L,R) ports (10)

(7)

Shutdown switch (61)

 

 

(14)

LAN port (10)

(8)

CONTROL port (10)

 

 

 

 

 

 

 

 

 

 

 

 

(14)

 

 

(1)

(3)

(4)

(5)

(6)

(7)

BATTERY

 

 

(8)

(9)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(2)

(10)(11) (13)

(12)

CAUTION ►Use the shutdown switch only when the projector is not turned off by normal procedure, since pushing this switch stops operation of the projector without cooling it down.

Part names

Remote control

(1)VIDEO button (17)

(2)COMPUTER button (16)

(3)SEARCH button (17)

(4)STANDBY/ON button (15)

(5)ASPECT button (17)

(6)AUTO button (19)

(7)BLANK button (21)

(8)MAGNIFY - ON button (20)

(9)MAGNIFY - OFF button (14, 20)

(10)HOME button (14)

(11)END button (14)

(12)PAGE UP button (14)

(13)PAGE DOWN button (14)

(14)VOLUME button (16)

(15)MUTE button (14, 16)

(16)FREEZE button (21)

(17)MY BUTTON - 1 button (42)

(18)MY BUTTON - 2 button (42)

(19)KEYSTONE button (20)

(20)POSITION button (19, 22)

(21)MENU button (22)

(22)▲/▼/◄/► cursor buttons (14, 22, 23)

(23)ENTER button (14, 22, 23)

(24)ESC button (14, 22)

(25)RESET button (14, 22, 23)

(26)Battery cover (13)

(2)(3)

(1)(4)

(5)

VIDEO

COMPUTER SEARCH

 

(6)

(10)

ASPECT

 

AUTO

BLANK

(7)

(8)

ON

 

 

 

(12)

 

MAGNIFY

HOME

PAGE UP

VOLUME

 

 

 

 

(9)

OFF

END

PAGE DOWN

MUTE

(14)

(11)

FREEZE

MY BUTTON

KEYSTONE

(15)

(16)

 

1

2

 

(13)

 

 

 

 

(17)

POSITION

 

 

MENU

(19)

(20)

 

 

 

 

(18)

(22)

 

ENTER

 

(21)

 

ESC

 

 

RESET

(23)

(24)(25)

Back of

the remote control

(26)

Setting up

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

8755G-RJ

The values shown in the table are calculated for a full size screen: 1024×768

a Screen size (diagonal)

b Projection distance (±10%)c1 ,c2 Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Keep a space of 30 cm or more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

between the sides of the projector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and other objects such as walls.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Consult with your dealer before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a special installation such as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

suspending from a ceiling.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

 

 

 

 

 

 

4 : 3 screen

 

 

 

 

 

 

 

 

 

16 : 9 screen

 

 

 

 

 

 

b

 

c1

 

c2

 

 

b

 

 

 

c1

 

c2

Screen size

 

 

 

 

 

 

 

 

 

 

Projection distance

Screen

Screen

Projection distance

Screen

Screen

(diagonal)

 

 

min.

 

 

 

max.

height

height

min.

max.

height

height

inch

m

m

inch

 

 

m

inch

cm

 

inch

cm

 

inch

m

inch

m

 

inch

cm

 

inch

cm

 

inch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

0.8

0.9

34

 

1.1

41

41

 

16

5

 

2

1.0

38

1.1

 

45

39

 

15

-1

 

0

40

1.0

1.2

46

 

1.4

56

55

 

22

6

 

2

1.3

50

1.5

 

61

51

 

20

-2

 

-1

50

1.3

1.5

58

 

1.8

70

69

 

27

8

 

3

1.6

63

1.9

 

76

64

 

25

-2

 

-1

60

1.5

1.8

70

 

2.1

84

82

 

32

9

 

4

1.9

76

2.3

 

91

77

 

30

-2

 

-1

70

1.8

2.1

81

 

2.5

98

96

 

38

11

 

4

2.3

89

2.7

 

107

90

 

35

-3

 

-1

80

2.0

2.4

93

 

2.8

112

110

 

43

12

 

5

2.6

102

3.1

 

122

103

 

41

-3

 

-1

90

2.3

2.7

105

 

3.2

126

123

 

49

14

 

5

2.9

115

3.5

 

138

116

 

46

-4

 

-1

100

2.5

3.0

117

 

3.6

140

137

 

54

15

 

6

3.2

127

3.9

 

153

129

 

51

-4

 

-2

120

3.0

3.6

140

 

4.3

169

165

 

65

18

 

7

3.9

153

4.7

 

184

154

 

61

-5

 

-2

150

3.8

4.5

176

 

5.4

211

206

 

81

23

 

9

4.9

192

5.8

 

230

193

 

76

-6

 

-2

200

5.1

6.0

235

 

7.2

282

274

 

108

30

 

12

6.5

256

7.8

 

307

257

 

101

-8

 

-3

250

6.4

7.5

294

 

9.0

353

343

 

135

38

 

15

8.1

320

9.8

 

384

322

 

127

-10

 

-4

300

7.6

9.0

352

 

10.8

423

411

 

162

46

 

18

9.8

384

11.7

 

461

386

 

152

-12

 

-5

7

Setting up

Arrangement (continued)

8912-RJ

The values shown in the table are calculated for a full size screen: 1024×768

a Screen size (diagonal)

b Projection distance (±10%)c1 ,c2 Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Keep a space of 30 cm or more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

between the sides of the projector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and other objects such as walls.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Consult with your dealer before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a special installation such as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

suspending from a ceiling.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

 

 

 

 

 

 

4 : 3 screen

 

 

 

 

 

 

 

 

 

16 : 9 screen

 

 

 

 

 

 

b

 

c1

 

c2

 

 

b

 

 

 

c1

 

c2

Screen size

 

 

 

 

 

 

 

 

 

 

Projection distance

Screen

Screen

Projection distance

Screen

Screen

(diagonal)

 

 

min.

 

 

 

max.

height

height

min.

max.

height

height

inch

m

m

inch

 

 

m

inch

cm

 

inch

cm

 

inch

m

inch

m

 

inch

cm

 

inch

cm

 

inch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

0.8

0.9

35

 

1.1

43

41

 

16

5

 

2

1.0

39

1.2

 

47

39

 

15

-1

 

0

40

1.0

1.2

47

 

1.4

57

55

 

22

6

 

2

1.3

52

1.6

 

62

51

 

20

-2

 

-1

50

1.3

1.5

59

 

1.8

71

69

 

27

8

 

3

1.6

65

2.0

 

78

64

 

25

-2

 

-1

60

1.5

1.8

71

 

2.2

86

82

 

32

9

 

4

2.0

78

2.4

 

94

77

 

30

-2

 

-1

70

1.8

2.1

83

 

2.5

100

96

 

38

11

 

4

2.3

91

2.8

 

109

90

 

35

-3

 

-1

80

2.0

2.4

95

 

2.9

115

110

 

43

12

 

5

2.6

104

3.2

 

125

103

 

41

-3

 

-1

90

2.3

2.7

107

 

3.3

129

123

 

49

14

 

5

3.0

117

3.6

 

141

116

 

46

-4

 

-1

100

2.5

3.0

119

 

3.6

144

137

 

54

15

 

6

3.3

130

4.0

 

156

129

 

51

-4

 

-2

120

3.0

3.6

143

 

4.4

172

165

 

65

18

 

7

4.0

156

4.8

 

188

154

 

61

-5

 

-2

150

3.8

4.6

179

 

5.5

216

206

 

81

23

 

9

4.9

195

6.0

 

235

193

 

76

-6

 

-2

200

5.1

6.1

239

 

7.3

288

274

 

108

30

 

12

6.6

261

8.0

 

314

257

 

101

-8

 

-3

250

6.4

7.6

299

 

9.1

360

343

 

135

38

 

15

8.3

326

10.0

 

392

322

 

127

-10

 

-4

300

7.6

9.1

359

 

11.0

432

411

 

162

46

 

18

9.9

391

12.0

 

471

386

 

152

-12

 

-5

8

Setting up

WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the projector. Using a damaged projector could then result in fire and/or electric shock.

Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand.

Do not place the projector on its side, front or rear position.

Consult with your dealer before a special installation such as suspending from a ceiling.

►Place the projector in a cool place, and ensure that there is sufficient ventilation. The high temperature of the projector could cause fire, burns and/ or malfunction of the projector.

Do not stop-up,block or otherwise cover the projector's vents.

Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

Do not place the projector on metallic thing or anything weak in heat.

Do not place the projector on carpet, cushions or bedding.

Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not anything near the projector lens or vents, or on top of the projector.

Do not place anything that may be sucked into or stick to the vents on the bottom of the projector. This projector has some intake vents also on the

bottom.

►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause fire, electric shock and/or malfunction of the projector.

Do not place the projector in a bathroom or the outdoors.

Do not place anything containing liquid near the projector.

CAUTION ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause fire, electric shock and/or malfunction of the projector.

• Do not place the projector near humidifiers, smoking spaces or a kitchen. ►Position the projector to prevent light from directly hitting the projector's remote sensor.

Setting up

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect.

Please refer to the following illustrations to connect them.

PC

Monitor

RS-232C

AUDIO OUT

RGB OUT

USB

AUDIO OUT

RGB OUT

LAN

RGB IN

Speakers

AUDIO IN

VCR/DVD

Y

CB/PB CR/PR

L

R

VIDEO OUT

L

R

L

R

 

player

COMPONENT VIDEO OUT

AUDIO OUT

AUDIO OUT

AUDIO OUT

S-VIDEOOUT

 

WARNING ►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables. CAUTION ►Turn off all devices and unplug their power cords prior to

connecting them to projector. Connecting a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction or damage to the device and the projector.

►Use appropriate accessory or otherwise designed cables. Ask your dealer about non-accessorycables which may have to be of a specific length or equipped with a core. For cables with a core only at one end, connect the end with the core to the projector.

►Make sure that devices are connected to the correct ports. An incorrect connection may result in malfunction or damage to the device and the projector.

10

Setting up

Connecting your devices (continued)

NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.

-Some signal may need an adapter to input this projector.

-Some PCs have multiple screen display modes that may include some signals which are not supported by this projector.

-Although the projector can display signals with resolution up to UXGA (1600X1200),

the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

While connecting, make sure that the shape of the cable's connector fits the port to connect with. And be sure to tighten the screws on connectors with screws.

When connecting a laptop PC to the projector, be sure to activate the PC’s external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC.

When the picture resolution is changed on a pc depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

In some cases, this projector may not display a proper picture or display any picture on screen. For example, automatic adjustment may not function correctly with some input signals. An input signal of composite sync or sync on G may confuse this projector, so the projector may not display a proper picture.

About Plug-and-Playcapability

Plug-and-Playis a system composed of a PC, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible.Plug-and-Play can be used by connecting this projector to a pc that is VESA DDC (display data channel) compatible.

Take advantage of this feature by connecting an RGB cable to the COMPUTER IN1 port (DDC 2B compatible). Plug-and-Playmay not work properly if any other type of connection is attempted.

Please use the standard drivers in your pc as this projector is a Plug-and-Playmonitor.

11

Setting up

Connecting power supply

At first, make sure that the power switch of the projector is set to OFF position (marked "O").

1.

2.

Put the connector of the power cord into the AC inlet of the projector.

Firmly plug the power cord’s plug into the outlet.

AC inlet

Power cord

WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock.

Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.

Only plug the power cord into an outlet rated for use with the power cord's specified voltage range. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

Never modify the power cord.

Using the security bar and slot

Security slot

A commercial anti-theftchain or wire up to 10 mm in diameter can be attached to the security bar on the projector.

Also this product has the security slot for the Kensington lock.

For details, see the manual of the security tool.

Anti-theftchain or wire Security bar

WARNING ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

CAUTION ►Do not placeanti-theftchain or wire near the exhaust vents. It may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention measures. It is intended to be used as supplemental theft prevention measure.

12

1.
2.

Remote control

Remote control

Putting batteries

Please set the batteries to the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery cover, remove it.

Align and insert the twoAAbatteries

according to their plus and minus terminals as indicated in the remote control.

3. Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets.

Do not recharge, short circuit, solder or disassemble a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front.

The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

Approx. 3 m

30º

30º

NOTE • The remote control signal reflected in the screen or the like may be available. If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.

The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector.Adjust the position of projector avoiding those lights.

13

Remote control

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal

 

 

 

 

 

 

frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote

 

VIDEO

COMPUTER SEARCH

 

 

control does not function properly, attempt to change the signal

 

ASPECT

 

AUTO

BLANK

 

frequency.

 

MAGNIFY

HOME

PAGE UP

VOLUME

 

In order to set the Mode, please keep pressing the combination of

 

ON

 

 

 

 

 

OFF

END

PAGE DOWN

MUTE

 

two buttons listed below simultaneously for about 3 seconds.

(2)

 

 

 

(1)

FREEZE

MY BUTTON

KEYSTONE

 

 

 

1

2

 

 

(1) Set to Mode 1:NORMAL... MUTE and RESET buttons

 

 

 

 

 

 

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

 

POSITION

 

 

MENU

 

Please remember that the REMOTE FREQ. in the SERVICE

 

 

ENTER

 

 

item of the OPTION menu (44) of the projector to be controlled

 

ESC

 

 

RESET

 

should be set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The enclosed remote control works as a simple mouse and

 

keyboard of the PC, when the projector's USB port (B type)

 

connects with the PC's USB port (A type) port via a mouse cable.

USB port

(1) HOME key: Press HOME button.

 

(2)

END key: Press END button.

 

(3) PAGE UP key: Press PAGE UP button.

USB

(4) PAGE DOWN key: Press PAGE DOWN button.

 

(5)

Mouse left button: Press ENTER button.

(1)

(6)

Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.

(7)

ESC key: Press ESC button.

 

(8)

Mouse right button: Press RESET button.

(2)

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

(3)

(4)

CAUTION ►Improper use of the simple mouse & keyboard function could damage your equipment. While using this function, please connect this product only to a PC. Be sure to check your PC’s manuals before connecting this product to the PC.

(5)

(7)

POSITION

MENU

 

ENTER

ESC

RESET

(6)

(8)

NOTE • When the simple mouse & keyboard function of this product does not work correctly, please check the following.

-When the mouse cable connects this projector with a PC having a built-inpointing device (e.g. track ball) like a notebook PC, open BIOS setup menu, then select the external mouse and disable thebuilt-inpointing device, because thebuilt-inpointing device may have priority to this function.

-Windows 95 OSR 2.1 or higher is required for this function.And also this function may not work depending on the PC’s configurations and mouse drivers.

-You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

-This function is activated only when the projector is working properly. This function is not available while the lamp is warming up (the POWER indicator blinks green), and while adjusting the volume and display, correcting for keystone, zooming in on the screen, using the BLANK function, or displaying the menu screen.

14

Power switch

Power on/off

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to ON position (marked “ I “).

The POWER indicator will light up in steady orange (60). Then wait several seconds because the buttons may not function for these several seconds.

3. Press STANDBY/ON button on the projector or the remote control.

The projection lamp will light up and POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (60).

Power on/off

STANDBY/ON button

POWER indicator

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

OFF

END

PAGE DOWN

MUTE

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

 

ENTER

 

ESC

 

 

RESET

Power switch

To display the picture, select an input signal according to the section “Selecting an input signal” (16).

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete(60).

3. Make sure that POWER indicator lights in steady orange, and set the power switch to OFF position (marked “O“).

POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for about 10 minutes or more after turning it off. Turning

the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector after all of connected devices are powered off.

The projector has theAUTO ON function, which can make the projector automatically turn on. For more information, please seeAUTO ON item of OPTION menu (40).

Use the shutdown switch (61) only when the projector is not turned off by normal procedure.

15

Operating

Operating

Adjusting the volume

1. Press VOLUME button on the remote control.

A dialog will appear on the screen to aid you in adjusting the volume.

VOLUME button

VIDEO COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

2. Use the ▲/▼ cursor buttons to adjust the volume.

To close the dialog and complete the operation, press the VOLUME button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

Whenis selected for current picture input port, the volume adjustment is disable. Please see AUDIO item of SETUP menu

(35).

Temporarily muting the sound

1. Press MUTE button on the remote control.

Adialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE or VOLUME button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

Whenis selected for current picture input port, the sound is always muted. Please see AUDIO item of SETUP menu(35).

Selecting an input signal

1. Press INPUT button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

COMPUTER IN 1 COMPUTER IN 2

S-VIDEOCOMPONENT (Y, Cb/Pb, Cr/Pr)

While TURN ON is selected for AUTO SEARCH item inVIDEO

OPTION menu (40), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

FREEZE

MY BUTTON

KEYSTONE

 

1

2

POSITION

 

MENU

 

ENTER

 

ESC

 

RESET

▲/▼ button MUTE button

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

INPUT button

1.

Press COMPUTER button on the remote control.

COMPUTER button

Each time you press the button, the projector switches

its input port from the current port as below.

 

COMPUTER IN 1COMPUTER IN 2

While TURN ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (40). If COMPUTER button is pushed when VIDEO,S-VIDEOor COMPONENT port is selected, the projector will check COMPUTER IN1 port first.

16 (continued on next page)

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

Selecting an input signal (continued)

1. Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

COMPONENT(Y, Cb/Pb, Cr/Pr)S-VIDEOVIDEO

Operating

VIDEO button

VIDEO COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

● While TURN ON is selected for AUTO SEARCH item in OPTION

FREEZE

menu, the projector will keep checking every port sequentially till

POSITION

an input signal is detected (40). If COMPUTER button is pushed

 

when VIDEO, S-VIDEOor COMPONENT port is selected, the projector check COMPUTER IN1 port first.

MY BUTTON

KEYSTONE

1

2

 

MENU

will

Searching an input signal

SEARCH button

Press SEARCH button on the remote control.

 

 

 

 

 

1. The projector will start to check its input ports as below

 

VIDEO

COMPUTER SEARCH

 

in order to find any input signals.

 

ASPECT

 

AUTO

BLANK

When an input is found, the projector will stop searching and

 

ON

 

 

 

 

 

MAGNIFY

HOME

PAGE UP

VOLUME

display the image. If no signal is found, the projector will return to

OFF

END

PAGE DOWN

MUTE

the state selected before the operation.

 

FREEZE

1

2

KEYSTONE

 

 

MY BUTTON

COMPUTER IN 1 COMPUTER IN 2

 

 

 

 

 

VIDEO S-VIDEOCOMPONENT (Y, Cb/Pb, Cr/Pr)

 

POSITION

 

 

MENU

While TURN ON is selected for AUTO SEARCH item in OPTION menu (40), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

Selecting an aspect ratio

1. Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

For a computer signal

NORMAL 4:316:9SMALL

ASPECT button

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

For a video signal,s-videosignal or component video signal

4:3 16:914:9SMALL

For no signal

4:3 (fixed)

ASPECT button does not work when no proper signal is inputted.

NORMAL mode keeps the original aspect ratio setting.

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

17

Operating

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally.

Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of theprojector within 10 degrees.This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

1. Holding the projector, push the elevator buttons to loose the elevator feet.

2. Position the front side of the projector to the desired height.

3. Release the elevator buttons in order to lock the elevator feet.

4. After making sure that the elevator feet are locked, put the projector gently.

5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet.

To loose an elevator foot, push the elevator button on the same side as it.

To finely adjust, twist the foot.

CAUTION ►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

►Do not tilt the projector other than it elevating its front within 10 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

Focus ring

Zoom ring

1.

Use the zoom ring to adjust the screen size.

 

 

2.

Use the focus ring to focus the picture.

 

 

18

 

 

Operating

Using the automatic adjustment feature

 

1.

Press AUTO button on the remote control.

AUTO button

Pressing this button performs the following.

 

For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. And the horizontal size will be automatically set to the default.

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

For a video signal, s-videosignal or component video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when AUTO is selected for VIDEO FORMAT item in INPUT menu (32).

The vertical position and horizontal position will be automatically set to the default. For a component video signal, also the horizontal phase will be automatically set to the default.

The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input. When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

The items adjusted by this function may vary when FINE or DISABLE is selected for AUTO ADJUST item of SERVICE item in OPTION menu (43).

Adjusting the position

1. Press POSITION button on the remote control when no menu is indicated.

The “POSITION” indication will appear on the screen.

2. Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on the remote control during the operation.

To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

FREEZE

MY BUTTON

KEYSTONE

 

1

2

POSITION

 

MENU

 

ENTER

 

ESC

 

RESET

POSITION button

When this function is performed on a video signal, s-videosignal or component video signal, some image such as anextra-linemay appear at outside of the picture.

When this function is performed on a video signal, s-videosignal or component video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu(29) setting. It is not possible to adjust when OVER SCAN is set to 10.

If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

19

SEARCH

Operating

Correcting the keystone distortions

1. Press KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion.

2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following.

(1)AUTO executes automatic vertical keystone correction.

(2)MANUAL displays a dialog for keystone correction. Use the ▲/▼ buttons for adjustment.

KEYSTONE button

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

POSITION

 

 

MENU

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

The adjustable range of this correction will vary among inputs. For some input, this function may not work well.

When V:INVERT or H&V:INVERT is selected for MIRROR item in SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.

When the zoom adjustment is set to TELE (telephoto focus), the automatic keystone distortion correction may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-anglefocus) whenever possible.

When the projector is placed on the level (about ±0°), the automatic keystone distortion correction may not work.

When the projector is inclined to near ±30 degree or over, this function may not work well.

This function will be unavailable when Transition Detector is on (49).

Using the magnify feature

1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen and the projector will go into the MAGNIFY mode. When the ON button of MAGNIFY is pressed first after the projector is started, the picture will be zoomed twice. The indication will disappear in several seconds with no operation.

MAGNIFY ON/OFF button

VIDEO COMPUTER

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

Use the ▲/▼ cursor buttons to adjust the zoom level. The picture of

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE MY BUTTON

KEYSTONE

2. video,s-videoor component video signal can be zoomed in up to 2

 

1

2

 

times, and the one of computer signal can be zoomed in up to 4 times.

POSITION

 

 

MENU

To move the zoom area, press POSITION button in the MAGNIFY

 

 

 

 

mode, then use the ▲/▼/◄/► cursor buttons to move the area. And to finalize the zoom area, press POSITION button again.

To exit from the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control.

The projector automatically exits from the MAGNIFY mode when the input signal is changed or when the display condition is changed.

In the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exits from the MAGNIFY mode.

NOTE • The zoom level can be finely adjusted. Closely watch the screen to find the level you want.

20

Operating

Freezing the screen

FREEZE button

Press FREEZE button on the remote control.

 

 

 

 

1. The “FREEZE” indication will appear on the screen (however,

 

 

 

 

the indication will not appear when TURN OFF is selected for

VIDEO

COMPUTER SEARCH

 

MESSAGE item in SCREEN menu (39)), and the projector will

ASPECT

 

AUTO

BLANK

go into the FREEZE mode, which the picture is frozen.

MAGNIFY

HOME

PAGE UP

VOLUME

To exit the FREEZE mode and restore the screen to normal,

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

press FREEZE button again.

 

 

 

FREEZE

MY BUTTON

KEYSTONE

 

 

1

2

 

● The projector automatically exits from the FREEZE mode when POSITION

 

 

MENU

one of the projector’s buttons or remote control buttons of

 

 

 

 

STANDBY/ON, SEARCH, COMPUTER, VIDEO, BLANK, AUTO, VOLUME, MUTE, KEYSTONE, MENU, MAGNIFY and MY BUTTON1/2(except

MY MEMORY or PICTURE MODE is assigned to) (42) is pressed.

If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

Temporarily blanking the screen

1. Press BLANK button on the remote control.

The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu

(36).

BLANK button

VIDEO COMPUTER SEARCH

ASPECT

AUTO BLANK

To exit from the BLANK screen and return to the input signal

MAGNIFY

HOME

PAGE UP

VOLUME

ON

END

PAGE DOWN

MUTE

screen, press BLANK button again.

FREEZE

MY BUTTON

KEYSTONE

 

OFF

 

 

 

● The projector automatically returns to the input signal screen

 

1

2

 

 

 

 

 

when one of the projector’s buttons or the remote control buttons

POSITION

 

 

MENU

(except ASPECT, POSITION, MAGNIFY or FREEZE button, also

except MY BUTTON1/2 if AUTO KEYSTONEEXECUTE or MY MEMORY or PICTURE MODE is assigned to(42)) is pressed.

NOTE • The sound is not connected with the BLANK screen function. If necessary, set the volume or mute first.

21

Operating

Using the menu function

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION, NETWORK and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classified into each purpose and brought together as Advanced Menu.

Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

MENU button

ENTER button

MENU button

 

 

Cursor buttons

 

POSITION

MENU

 

 

ENTER

 

ESC

RESET

 

ESC button

RESET button

1. Press the MENU button on the remote control or the projector.

The Advanced Menu or EASY MENU, which has priority just after powered on will appear.

If you want to move the menu position, use the cursor buttons after pressing the POSITION button. While the projector is displaying any menu, MENU button on the projector works as the cursor buttons.

In the EASY MENU

2. If you want to change it to the Advanced Menu, select the Go to Advanced Menu...

3. Useoperate.the ▲/▼ cursor buttons to select an item to

4. Use the ◄/► cursor buttons to operate the item.

EASY MENU

(continued on next page)

22

Operating

Using the menu function (continued)

In the Advanced Menu

2. Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select EASY MENU.

Then press the ► cursor button, or ENTER button to select an item. The lower layer menu of the selected item

will appear. Advanced Menu

3. Useoperate.the ▲/▼ cursor buttons to select an item to

Then press the ► cursor button, or ENTER button to progress. The operation menu of the selected item will appear.

4. Use the ▲/▼ cursor buttons to operate the item.

Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, H PHASE, VOLUME) cannot be reset.

In the Advanced Menu, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

5. Press MENU button on the remote control again to close the menu and complete this operation. Even if you do not do anything, the dialog will automatically disappear after about 10 seconds.

23

EASY MENU

EASYMENU

From the EASY MENU, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item

 

Description

ASPECT

Using the ◄/► buttons switches the mode for aspect ratio.

See the ASPECT item in IMAGE menu (29).

 

AUTO

Using the ► button executes the auto keystone function.

KEYSTONE

See AUTO KEYSTONE EXECUTE item in SETUP menu (34).

EXECUTE

 

 

KEYSTONE

Using the ◄/► buttons corrects the vertical keystone distortion.

See KEYSTONE

item in SETUP menu (34).

 

Using the ◄/► buttons switches the picture mode.

The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source.

 

NORMAL ó CINEMAó DYNAMICó BOARD(BLACK)

 

DAYTIME ó WHITEBOARDó BOARD(GREEN)

 

 

 

 

 

 

COLOR TEMP

GAMMA

 

 

 

 

 

NORMAL

#2 MID DEFAULT

#1 DEFAULT

PICTURE MODE

CINEMA

#3 LOW DEFAULT

#2 DEFAULT

DYNAMIC

#1 HIGH DEFAULT

#3 DEFAULT

 

BOARD(BLACK)

#4 Hi-BRIGHT-1DEFAULT

#4 DEFAULT

 

BOARD(GREEN)

#5 Hi-BRIGHT-2DEFAULT

#4 DEFAULT

 

WHITEBOARD

#2 MID DEFAULT

#5 DEFAULT

 

DAYTIME

#6 Hi-BRIGHT-3DEFAULT

#6 DEFAULT

When the combination of GAMMA and COLOR TEMP differs from pre-assignedmodes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to GAMMA (26) and COLOR TEMP (26) items in PICTURE menu.

When this function is performed, a certain extra such as a line may appear.

(continued on next page)

24

EASY MENU

EASY MENU (continued)

Item

Description

BRIGHTNESS

Using the ◄/► buttons adjusts the brightness.

See BRIGHTNESS item in PICTURE menu (26).

 

CONTRAST

Using the ◄/► buttons adjusts the contrast.

See CONTRAST item in PICTURE menu (26).

 

COLOR

Using the ◄/► buttons adjusts the strength of whole color.

See COLOR item in PICTURE menu (26).

 

TINT

Using the ◄/► buttons adjusts the tint.

See TINT item in PICTURE menu (26).

 

SHARPNESS

Using the ◄/► buttons adjusts the sharpness.

See SHARPNESS item in PICTURE menu (27).

 

WHISPER

Using the ◄/► buttons turns off/on the whisper mode.

See WHISPER item in SETUP menu (35).

 

MIRROR

Using the ◄/► buttons switches the mode for mirror status.

See MIRROR item in SETUP menu (35).

 

 

Performing this item resets all of EASY MENU items except FILTER

RESET

TIME and LANGUAGE.

A dialog is displayed for confirmation. Selecting RESET using the

 

 

▲ button performs resetting.

Performing this item resets the filter time which counts usage time of the air filter.

FILTER TIME A dialog is displayed for confirmation. Selecting RESET using the ▲ button performs resetting.

See FILTER TIME item in OPTION menu (41).

LANGUAGE

Using the ◄/► buttons changes the display language.

See LANGUAGE item in SCREEN menu (36).

 

Go to

Select Go to Advanced Menu… on the menu, and press the ►

or ENTER button to use the menu of PICTURE, IMAGE, INPUT,

Advanced Menu...

SETUP, SCREEN, OPTION or NETWORK.

25

PICTURE menu

PICTUREmenu

From the PICTURE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

 

Description

 

 

BRIGHTNESS

Using the ▲/▼ buttons adjusts the brightness.

Light ó Dark

 

 

 

CONTRAST

Using the ▲/▼ buttons adjusts the contrast.

Strong ó Weak

 

 

 

 

Using the ▲/▼ buttons switches the gamma mode.

 

#1 DEFAULT #1 CUSTOM #2 DEFAULT #2 CUSTOM

 

 

 

 

#6 CUSTOM

#3 DEFAULT

GAMMA

 

 

#6 DEFAULT

#3 CUSTOM

 

 

 

 

#5 CUSTOM #5 DEFAULT #4 CUSTOM #4 DEFAULT

 

To adjust the "CUSTOM" modes, see "To adjust CUSTOM function

 

in GAMMA and COLOR TEMP" (28).

 

Using the ▲/▼ buttons switches the color temperature mode.

 

#1 HIGH DEFAULT #1 HIGH CUSTOM #2 MID DEFAULT

 

 

 

 

#6 Hi-BRIGHT-3CUSTOM

#2 MID CUSTOM

 

 

 

COLOR TEMP

#6 Hi-BRIGHT-3DEFAULT

#3 LOW DEFAULT

 

 

 

#5 Hi-BRIGHT-2CUSTOM

#3 LOW CUSTOM

 

 

 

 

#5 Hi-BRIGHT-2DEFAULT #4Hi-BRIGHT-1CUSTOM #4Hi-BRIGHT-1DEFAULT

 

To adjust the "CUSTOM" modes, see "To adjust CUSTOM function

 

in GAMMA and COLOR TEMP" (28).

 

Using the ▲/▼ buttons adjusts the strength of whole color.

COLOR

Strong ó Weak

 

• This item can be selected only for a video signal, s-videoor

 

 

component video signal.

 

 

Using the ▲/▼ buttons adjusts the tint.

TINT

Greenish ó Reddish

 

• This item can be selected only for a video signal, s-videoor

 

 

component video signal.

 

(continued on next page)

26

PICTURE menu

PICTURE menu (continued)

Item

Description

 

 

 

Using the ▲/▼ buttons adjusts the sharpness.

SHARPNESS

Strong ó Weak

• There may be some noise and/or the screen may flicker for a

 

 

moment when an adjustment is made. This is not a malfunction.

 

This projector has 4 memories for adjustment data (for all the items

 

of PICTURE menu).

 

Selecting a function using the ▲/▼ buttons and pressing the ► or

 

ENTER button performs each function.

 

LOAD-1ó LOAD-2ó LOAD-3ó LOAD-4

 

SAVE-4óSAVE-3ó SAVE-2ó SAVE-1

 

LOAD-1,LOAD-2,LOAD-3,LOAD-4

 

Performing a LOAD function loads the data from the memory linked

 

in the number included in the function’s name, and adjusts the

 

picture automatically depending on the data.

MY MEMORY

• The LOAD functions whose linked memory has no data are

skipped.

 

• Remember that the current adjusted condition will be lost by

 

loading data. If you want to keep the current adjustment, please

 

save it before performing a LOAD function.

 

• There may be some noise and the screen may flicker for a

 

moment when loading data. This is not malfunction.

 

• You can perform the LOAD function using MY BUTTONs. Please

 

see MY BUTTON item in OPTION menu (42).

 

SAVE-1,SAVE-2,SAVE-3,SAVE-4

 

Performing a SAVE function saves the current adjustment data into

 

the memory linked in the number included in the function’s name.

 

• Remember that the current data being stored of a memory will be

 

lost by saving a new data into the memory.

27

PICTURE menu

PICTURE menu (continued)

To adjust CUSTOM function in GAMMA and COLOR TEMP

Selecting a mode whose name includes CUSTOM in GAMMA or COLOR TEMP item and then pressing the ► button or ENTER button displays a dialog to aid you in adjusting the mode.

Choose an item using the ◄/► buttons, and

adjust the level using the ▲/▼ buttons. GAMMA COLOR TEMP

• When this function is performed, lines or other distortion may appear.

You can display a test pattern on the top of the screen for

 

checking the effect of your adjustment by pressing the ENTER

 

button. Each time you press the ENTER button, the pattern

 

changes as below.

 

test pattern

No pattern Gray scale of 9 steps

 

 

Ramp Gray scale of 15 steps

 

• You can also adjust each function without displaying test patterns.

 

for adjusting GAMMA

You can change the brightness of particular tones.

The eight equalizing bars correspond to eight tone levels of the test pattern (Gray scale of 9 steps) except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

for adjusting COLOR TEMP

You can change the intensity of each of 3 colors (Red, Green, Blue).

OFFSET adjustments change the color intensity on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.

28

IMAGE menu

IMAGEmenu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For a computer signal

 

NORMAL ó 4:3ó 16:9ó SMALL

ASPECT

For a video signal, s-videosignal or component video signal

4:3 ó 16:9ó 14:9ó SMALL

 

For no signal

 

4:3 (fixed)

 

• This item can be selected only for a proper signal.

 

• NORMAL mode keeps the original aspect ratio setting.

 

Using the ▲/▼ buttons adjusts the over-scanratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-videoand component video signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

Over-adjustingthe vertical position may cause noise to appear on the

 

screen. If this occurs please reset the vertical position to the default setting.

V POSITION

Pressing RESET button when V POSITION is selected will reset V

POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-videosignal, or

 

component video signal, the range of this adjustment depends on OVER

 

SCAN (above) setting. It is not possible to adjust when OVER SCAN is

 

set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

Over-adjustingthe horizontal position may cause noise to appear on the

 

screen. If this occurs please reset the horizontal position to the default setting.

H POSITION

Pressing RESET button when H POSITION is selected will reset H

POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-videosignal, or

 

component video signal, the range of this adjustment depends on OVER

 

SCAN (above) setting. It is not possible to adjust when OVER SCAN is

 

set to 10.

(continued on next page)

29

IMAGE menu

IMAGE menu (continued)

Item

Description

 

 

 

Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.

H PHASE

Right ó Left

• This item can be selected only for a computer signal or component

 

 

video signal.

 

Using the ▲/▼ buttons adjusts the horizontal size.

 

Large ó Small

H SIZE

• This item can be selected only for a computer signal.

 

• When this adjustment is excessive, the picture may not be

 

displayed correctly. In such a case, please reset the adjustment by

 

pressing the RESET button during this operation.

 

Executing this item performs the automatic adjustment feature.

 

For a computer signal

 

The vertical position, the horizontal position and the horizontal

 

phase (43) will be automatically adjusted. And the horizontal size

 

will be automatically set to the default.

 

Make sure that the application window is set to its maximum size

 

prior to attempting to use this feature. A dark picture may still be

 

incorrectly adjusted. Use a bright picture when adjusting.

 

For a video signal, s-videosignal or component video signal

 

The video format best suited for the respective input signal will be

AUTO ADJUST

selected automatically.

This function is available only when the AUTO mode is selected to

EXECUTE

VIDEO FORMAT item in INPUT menu (32).

 

The vertical position and horizontal position will be automatically set

 

to the the default.

 

For a component video signal, also the horizontal phase will be

 

automatically set to the default.

 

• The automatic adjustment operation requires approx. 10 seconds.

 

Also please note that it may not function correctly with some input.

 

When this function is performed for a video signal, a certain extra

 

such as a line may appear outside a picture.

 

• The items adjusted by this function may vary when FINE or

 

DISABLE is selected for AUTO ADJUST item of SERVICE item in

 

OPTION menu (43).

30

INPUT menu

INPUTmenu

From the INPUT menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the progress mode.

 

TV ó FILMó TURN OFF

 

• This function is performed only for an interlaced signal of a video,

PROGRESSIVE

s-videoor component video of 525i (480i) or 625i (576i) signal.

 

• When TV or FILM is selected, the screen image will be sharp.

 

FILM adapts to the 2-3Pull-Downconversion system. But these

 

may cause a certain defect (for example, jagged line) of the picture

 

for a quick moving object. In such a case, please select TURN OFF,

 

even though the screen image may lose the sharpness.

 

Using the ▲/▼ buttons switches the noise reduction mode.

 

HIGH ó MIDó LOW

VIDEO NR

• This function performs only for a video, s-videoor component

 

video of 525i(480i) or 625i(576i) signal.

 

• When this function is excessive, it may cause a certain

 

degradation of the picture.

 

Using the ▲/▼ buttons switches the mode for color space.

 

AUTO ó RGBó SMPTE240ó REC709ó REC601

COLOR SPACE

• This item can be selected only for a computer signal or component

video signal except SCART RGB signal.

 

• The AUTO mode automatically selects the optimum mode.

 

• The AUTO operation may not work well at some signals. In such a

 

case, it might be good to select a suitable mode except AUTO.

 

Using the ▲/▼ buttons switches the function of the COMPONENT

 

(Y, Cb/Pb, Cr/Pr) port.

COMPONENT

COMPONENT ó SCART RGB

When the SCART RGB is selected, COMPONENT (Y, Cb/Pb, Cr/

 

Pr) and VIDEO ports will function as a SCART RGB port. A SCART

 

cable is required for a SCART RGB input to the projector. For your

 

reference, see the TECHNICAL part.

(continued on next page)

31

INPUT menu

INPUT menu (continued)

Item

Description

 

 

 

The video format for S-VIDEOport and VIDEO port can be set.

 

(1) Use the ◄/► buttons to select the input port.

 

(2) Using the ▲/▼ buttons switches the mode

 

for video format.

 

AUTO ó NTSCó PALó SECAM

VIDEO FORMAT

N-PALó M-PALó NTSC4.43

• This item is performed only for a video signal

 

 

from VIDEO port or S-VIDEOport.

 

• The AUTO mode automatically selects the optimum mode.

 

• The AUTO operation may not work well for some signals. If the

 

picture becomes unstable (e.g. an irregular picture, lack of color),

 

please select the mode according to the input signal.

 

Using the ▲/▼ buttons turns the frame lock function on/off.

 

TURN ON ó TURN OFF

 

• This item can be performed only on a computer signal with a

FRAME LOCK

vertical frequency of 50 to 60 Hz.

 

• When the TURN ON is selected, a moving pictures are displayed

 

more smoothly.

 

• This function may cause a certain degradation of the picture. In

 

such a case, please select TURN OFF.

 

The computer input signal type for COMPUTER IN1 and IN2 ports

 

can be set.

 

(1) Use the ◄/► buttons to select the input

 

port to be set.

 

COMPUTER (IN)1 ó COMPUTER (IN)2

 

(2) Use the ▲/▼ buttons to select the

COMPUTER IN

computer input signal type.

SYNC ON G ON ó SYNC ON G OFF

 

 

Selecting SYNC ON G ON allows reception of sync on Green

 

signal.

 

• When SYNC ON G ON is selected, the picture may be distorted

 

with certain input signals. In such a case, remove the signal

 

connector first and select SYNC ON G OFF on the menu, and then

 

reconnect the signal.

(continued on next page)

32

INPUT menu

INPUT menu (continued)

Item

Description

The resolution for the COMPUTER IN1 and IN2 input signals can be set on this projector.

(1)In INPUT menu select RESOLUTION using the ▲/▼ buttons and press the ► button.

The RESOLUTION menu will be displayed.

(2)In the RESOLUTION menu, select

the resolution you wish to display using the ▲/▼ buttons.

Selecting AUTO will set a resolution appropriate to the input signal.

 

(3) STANDARD

 

 

Pressing the ► or ENTER button when

STANDARD

 

selecting a STANDARD resolution will

 

automatically adjust the horizontal and

 

 

vertical positions, clock phase and

 

 

horizontal size and automatically select

 

 

an aspect ratio.

 

 

(3) CUSTOM

 

RESOLUTION

(3)-1To set a custom resolution use the

CUSTOM

▲/▼ buttons to select the CUSTOM

 

and the CUSTOM RESOLUTION

 

 

 

box will be displayed. Set the

 

 

horizontal (HORZ) and vertical

 

 

(VERT) resolutions using the ▲

 

 

/▼/◄/► buttons. Although not all

 

 

resolutions are guaranteed.

 

 

(3)-2To save the setting place the

 

 

cursor on the right-mostdigit and

 

 

press the ► button.

 

 

The horizontal and vertical positions,

 

 

clock phase and horizontal size will

 

 

be automatically adjusted and an

 

 

aspect ratio will be automatically

 

 

selected.

 

 

(3)-3To revert back to the previous

 

 

resolution without saving changes

 

 

place the cursor on the left-most

 

 

digit and press the ◄ button.

 

 

The screen will then return to the

 

 

RESOLUTION menu displaying the

 

 

previous resolution.

 

 

• For some pictures, this function may not work well.

33

SETUP menu

SETUP menu

From the SETUP menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Selecting this item performs the automatic keystone distortion

 

correction. Projector automatically corrects vertical keystone

 

distortion due to the (forward/backward) setup angle by itself.

 

This function will be executed only once when selected in the menu.

 

When the slant of the projector is changed, execute this function

 

again.

 

• The adjustable range for correction will vary among inputs. For

 

some input, this function may not work well.

AUTO

• When V:INVERT or H&V:INVERT is selected to the MIRROR item

in the SETUP menu, if the projector screen is inclined or angled

KEYSTONE

downward, this function may not work correctly.

EXECUTE

• When the zoom adjustment is set to the TELE (telephoto focus),

 

this function may be excessive. This function should be used when

 

the zoom adjustment is set to the full WIDE (wide-anglefocus)

 

whenever possible.

 

• When the projector is placed on the level (about ±0°), this function

 

may not work.

 

• When the projector is inclined to near ±30 degree or over, this

 

function may not work well.

 

• This function will be unavailable when the Transition Detector is

 

on (49).

 

Using the ▲/▼ buttons corrects the vertical keystone distortion.

 

Shrink the top of the image ó Shrink the bottom of the image

KEYSTONE

• The adjustable range of this function will vary with the type of input

 

signal. For some input, this function may not work well.

 

• This function will be unavailable when the Transition Detector is

 

on (49).

(continued on next page)

34

SETUP menu

SETUP menu (continued)

Item

Description

Using the ▲/▼ buttons turns off/on the whisper mode.

WHISPER

NORMAL ó WHISPER

• When WHISPER is selected, acoustic noise and screen brightness

 

 

are reduced.

 

Using the ▲/▼ buttons switches the mode for mirror status.

MIRROR

NORMAL ó H:INVERTó V:INVERTó H&V:INVERT

 

If the Transition Detector is TURN ON and MIRROR status is

 

changed, Transition Detector Alarm (49) will be displayed when

 

projector is restarted after the power switch is turned off.

VOLUME

Using the ▲/▼ buttons adjusts the volume.

High ó Low

 

Using the ▲/▼ buttons turns on/off the built-inspeaker.SPEAKER TURN ONó TURN OFF

When TURN OFF is selected, the built-inspeaker does not work.

Allocates the audio ports.

(1)Choose a picture input port using the ▲/▼ buttons.

COMPUTER (IN)1ó COMPUTER (IN)2

VIDEO ó S-VIDEOó COMPONENT

AUDIO

(2) Select the audio port to be interlocked

with the input port using the ◄/►

 

 

buttons.

 

1 ó 2ó 3ó

When is selected to an input port, any audio ports do not work interlocking with the input port.

35

SCREEN menu

SCREEN menu

From the SCREEN menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

Using the ▲/▼ buttons switches the OSD (On Screen Display) language.

 

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

 

 

 

 

 

 

TÜRKÇE

 

 

NORSK

LANGUAGE

 

 

 

 

POLSKI

 

 

NEDERLANDS

 

 

 

 

 

 

 

 

 

SUOMI

 

 

PORTUGUÊS

 

 

 

 

 

 

РУССКИЙ SVENSKA

 

 

 

Using the ▲/▼/◄/► buttons adjusts the menu position.

MENU POSITION To quit the operation, press MENU button on the remote control or keep no operation for about 10 seconds.

 

Using the ▲/▼ buttons switches the mode for the BLANK screen.

 

The BLANK screen is a screen for the temporarily blanking feature

 

(21). It is displayed by pressing BLANK button.

 

MyScreen ó ORIGINALó BLUEó WHITEó BLACK

BLANK

 

Feature

MyScreen

Screen can be registered by the MyScreen item

 

(38).

 

 

 

ORIGINAL

Screen preset as the standard screen.

 

BLUE, WHITE,

Plain screens in each color.

 

BLACK

 

 

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.

(continued on next page)

36

SCREEN menu

SCREEN menu (continued)

Item

 

Description

 

Using the ▲/▼ buttons switches the mode for the start-upscreen.

 

The start-upscreen is a screen displayed when no signal or an

 

unsuitable signal is detected.

 

MyScreen ó ORIGINALó TURN OFF

 

 

Feature

 

MyScreen

Screen can be registered by the MyScreen item

 

(38).

START UP

 

ORIGINAL

Screen preset as the standard screen.

 

TURN OFF

Plain black screen.

To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen (36) after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.

When the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (46), the START UP is fixed to MyScreen.

(continued on next page)

37

SCREEN menu

SCREEN menu (continued)

Item

Description

 

 

 

 

 

This item allows you to capture an image for use as a MyScreen

 

image which can be used as the BLANK screen and START UP

 

screen. Display the image you want to capture before executing the

 

following procedure.

 

1. Selecting this item displays a dialog

 

titled “MyScreen”. It will ask you if

 

you start capturing an image from

 

the current screen.

 

Please wait for the target image to be displayed, and press the

 

ENTER button when the image is displayed. The image will

 

freeze and the frame for capturing will appear.

 

To stop performing, press the RESET or ESC button.

 

2. Using the ▲/▼/◄/► buttons adjusts

 

 

 

 

 

 

the frame position.

 

 

 

Please move the frame to the position

 

 

 

of the image which you want to use.

 

 

MyScreen

The frame may not be able to be

 

 

moved for some input signals.

 

 

 

 

 

 

To start registration, press the ENTER

 

 

 

button.

 

 

 

To restore the screen and return to

 

 

 

the previous dialog, press the RESET

 

or ESC button.

 

Registration takes several minutes.

When the registration is completed, the registered screen and the following message are displayed for several seconds:

“MyScreen registration is finished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

This function cannot be selected when the TURN ON is selected to the MyScreen Lock item (below).

This function cannot be selected when TURN ON is selected to

the MyScreen PASSWORD of SECURITY item in OPTION menu (46).

Using the ▲/▼ buttons turns on/off the MyScreen lock function. TURN ON ó TURN OFF

When the TURN ON is selected, the MyScreen item is locked. Use MyScreen Lock this function for protecting the current MyScreen.

• This function cannot be selected when TURN ON is selected to

the MyScreen PASSWORD of SECURITY item in OPTION menu (46).

(continued on next page)

38

SCREEN menu

SCREEN menu (continued)

Item

Description

 

 

 

Using the ▲/▼ buttons turns on/off the message function.

 

TURN ON ó TURN OFF

 

When the TURN ON is selected, the following message function works.

 

“AUTO IN PROGRESS” while automatically adjusting

 

“NO INPUT IS DETECTED”

 

“SYNC IS OUT OF RANGE”

 

“Searching…” while searching for the input

MESSAGE

“Detecting…” while an input signal is detected

The indication of the input signal displayed by changing

 

The indication of the aspect ratio displayed by changing

 

The indication of the PICTURE MODE displayed by changing

 

The indication of the MY MEMORY displayed by changing

 

The indication of “FREEZE” and “II” while the projector is in the

 

FREEZE mode.

 

• If the projector goes into the FREEZE mode while the TURN OFF

 

is selected, the picture on screen is frozen without any messages,

 

which is not a malfunction. (21)

Each input port for this projector can have a name applied to it.

(1)Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► button. The SOURCE NAME menu will be displayed.

(2)Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. Right side of the menu is blank until a name is specified. The SOURCE NAME dialog will be displayed.

(3)The current name will be displayed on the first line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. The RESET button can be used to

SOURCE NAME erase 1 character at a time. The name can be a maximum of 16 characters.

(4)To change an already inserted character, press the ▲ button while the cursor is on the [A-N]row to move the cursor to the name displayed on the first line and use the ◄/► buttons to select character to be changed. Once a character in the name is selected use the ▼ button to move the cursor back down to the character entry area to select and enter characters as described above.

(5)Select and press ENTER or INPUT buttons when finished entering text.

To revert to the previous name without saving changes press the ESC or ◄ button and the INPUT button simultaneously.

39

OPTION menu

OPTION menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons turns on/off the automatic signal search function.

 

TURN ON TURN OFF

When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. The search is

AUTO SEARCH started from the current port. Then when an input is found, the projector will stop searching and display the image.

COMPUTER IN1 COMPUTER IN2

 

VIDEO S-VIDEOCOMPONENT

 

 

 

Using the ▲/▼ buttons turns on/off the automatic keystone function.

 

TURN ON TURN OFF

 

TURN ON : Automatic keystone distortion correction will be

 

executed whenever changing the slant of the projector.

AUTO

TURN OFF : This function is disabled. Please execute the AUTO

KEYSTONE

KEYSTONE EXECUTE in the SETUP Menu for automatic

keystone distortion correction.

 

 

• When the projector is suspended from the ceiling this feature will

 

not function properly so select the TURN OFF.

 

• This function will be unavailable when the Transition Detector is

 

on (49).

 

Using the ▲/▼ buttons turns on/off the AUTO ON function.

 

TURN ON TURN OFF

 

When set to the TURN ON, the lamp in projector will be

 

automatically turned on without the usual procedure (15), only

AUTO ON

when the projector is supplied with the power after the power was

cut while the lamp was on.

This function does not work as long as the power has been supplied to the projector while the lamp is off.

After turning the lamp on by the AUTO ON function, if neither input

nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO OFF function (41) is disabled.

(continued on next page)

40

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

Using the ▲/▼ buttons adjusts the time to count down to

 

automatically turn the projector off.

 

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

AUTO OFF

When the time is set to 0, the projector is not turned off automatically.

When the time is set to 1 to 99, and when the passed time with no-

 

 

signal or an unsuitable signal reaches at the set time, the projector

 

lamp will be turned off.

 

If one of the projector's buttons or the remote control buttons

 

is pressed or one of the commands (except get commands) is

 

transmitted to the CONTROL port during the corresponding time,

 

projector will not be turned off.

 

Please refer to the section “Turning off the power” (15).

 

The lamp time is the time counted after the last resetting. It is

 

shown in OPTION menu as the usage time of the lamp.

 

Pressing RESET button or the ► button displays a dialog.

LAMP TIME

To reset the lamp time, select RESET using the ▲ button.

RESET ï CANCEL

 

 

• Please reset the lamp time only when you have replaced the lamp,

 

for a suitable indication about the lamp.

 

• For the lamp replacement, see the section "Lamp" (54).

 

The filter time is the time counted after the last resetting. It is shown

 

in the OPTION menu as the usage time of the air filter.

 

Pressing the RESET button or the ► button displays a dialog.

FILTER TIME

To reset the filter time, select the RESET using the ▲ button.

RESET ï CANCEL

 

 

• Please reset the filter time only when you have cleaned or replaced

 

the air filter, for a suitable indication about the air filter.

 

• For the air filter cleaning, see the section "Air filter" (56).

(continued on next page)

41

OPTION menu

OPTION menu (continued)

Item

Description

This item is to assign one of the following functions to MY BUTTON 1 and 2 on the remote control (6).

Choose 1 or 2 on the MY BUTTON menu using the ◄/► button first. Then using the ▲/▼ buttons sets one of the following functions to the chosen button.

COMPUTER1: Sets port to COMPUTER IN1.

COMPUTER2: Sets port to COMPUTER IN2.

COMPONENT: Sets port to COMPONENT(Y, Cb/Pb, Cr/Pr)

S-VIDEO:Sets port toS-VIDEO.

VIDEO: Sets port to VIDEO.

e-SHOT:Displays thee-SHOTmenu (52).

INFORMATION: Displays a dialog of INPUT -INFORMATION-or NETWORK-INFORMATION-(44, 53).

The displayed dialog is switched as below every time the MY BUTTON is pushed.

When an input signal is found:

INPUT -INFORMATION-NETWORK-INFORMATION-OFF

MY BUTTON

When an input signal is not found:

NETWORK -INFORMATION-OFF

AUTO KEYSTONE EXECUTE:

Performs automatic keystone distortion correction (34).

MY MEMORY: Loads one of adjustment data stored (27).

When more than one data are saved, the adjustment changes every time the MY BUTTON is pushed.

When no data is saved in memory, the dialog "No saved data" appears.

When the current adjustment is not saved to memory, the dialog as shown in the right appears.

If you want to keep the current adjustment, please press the ◄ button to quit. Otherwise loading a data will lose the current adjusted condition.

PICTURE MODE: Changes the PICTURE MODE (24).

FILTER RESET: Displays the filter time reset confirmation dialogue (41).

VOLUME+: Set the volume up.

VOLUME-:Set the volume down.

Selecting this item displays the SERVICE menu.

Select an item using the ▲/▼ buttons, and press the ► button or the

ENTER button to execute the item.

FAN SPEED AUTOADJUSTGHOSTFILTER MESSAGEKEYLOCK

SERVICE

FACTORYRESET I NFORMATIONREMOTE FREQ.

FAN SPEED

 

 

Using the ▲/▼ buttons switches the rotation speed

 

of the cooling fans. The HIGH is the mode for use at

 

highlands etc. Note that the projector is noisier when the

 

HIGH is selected.

 

HIGH ó NORMAL

(continued on next page)

42

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

AUTO ADJUST

 

Using the ▲/▼ buttons enables/disables the

 

automatic adjustment. When DISABLE is selected,

 

the automatic adjustment feature is disabled,

 

although rough adjustment is automatically performed

 

depending on the basic setting.

 

FINE ó FASTó DISABLE

 

FINE: Finer tuning including H.SIZE adjustment.

 

FAST: Faster tuning, setting H.SIZE to prearranged data for the

 

input signal.

 

• Depending on conditions, such as input image, signal cable to

 

the projector, environment around the projector, etc., the automatic

 

adjustment may not work correctly. In such a case, please

 

choose DISABLE to disable the automatic adjustment, and make

 

adjustment manually.

 

GHOST

 

1. Select a color element of ghost using the ◄/►

 

buttons.

SERVICE

2. Adjust the selected element using the ▲/▼ buttons to

(continued)

disappear ghost.

 

FILTER MESSAGE

 

Use the ▲/▼ button to set the timer for the interval to

 

show the message for cleaning up the air filter.

 

50h ó 100hó 200hó 300hó 400hó 500h

 

TURN OFF ó 800hó 700hó 600h

After choosing a choice except TURN OFF, the message “REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK” will appear after the timer reaches the interval time set by this feature (59).

When the TURN OFF is chosen, the message will not appear. Utilize this feature to keep the air filter clean, setting the suitable time according to your environment of this projector.

Please check and clean the air filter periodically, even if there is no message. If the air filter becomes to be blocked by dust or others, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

Please be careful with the operating environment of the projector and the condition of the air filter.

(continued on next page)

43

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

KEY LOCK

 

Using the ▲/▼ buttons turns on/off the key lock feature. When

 

TURN ON is selected, the buttons on the projector except the

 

STANDBY/ON button are locked.

 

TURN ON ó TURN OFF

 

• Please use to avoid a mischief and touching accidentally. This

 

function does not have any effect on the remote control.

 

REMOTE FREQ.

 

Use the ▲/▼ button to change the projector's remote sensor

 

setting.

 

1:NORMAL ó 2:HIGH

 

Items with a checkmark are on. The factory

 

default setting is for both 1:NORMAL and 2:

 

HIGH to be on. If the remote control does not

 

function correctly set this to either only 1 or

SERVICE

only 2 (14).

Neither can be turned off at the same time.

(continued)

INFORMATION

 

 

Selecting this item displays a dialog titled “INPUT -INFORMATION-”.

 

It shows the information about the current input.

The “FRAME LOCK” message on the dialog means the frame lock function is working (32).

This item can't be selected for no signal and sync out.

FACTORY RESET

Selecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, SECURITY and NETWORK settings are not reset.

RESET ï CANCEL

(continued on next page)

44

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

This projector is equipped with security functions.

 

User registration is required before using the security functions.

 

Please contact your local dealer.

 

1. Using Security Features

 

1.1 Inputting the PASSWORD

 

1.1-1Use the ▲/▼ buttons on the OPTION

 

menu to select SECURITY and press the

 

► button. The ENTER PASSWORD box

 

will be displayed.

 

The factory default PASSWORD is 8471.

 

This PASSWORD can be changed (1.2 Changing the PASSWORD (

 

below)).

 

• It is strongly recommended the factory default PASSWORD to be

 

changed as soon as possible.

 

1.1-2Use the ▲/▼/◄/► buttons to enter

 

the registered PASSWORD. Move the

 

cursor to the right side of the ENTER

 

PASSWORD box and press the ► button

 

to display the SECURITY menu.

 

If an incorrect PASSWORD is input the

 

ENTER PASSWORD box will be displayed again. If incorrect

SECURITY

PASSWORD is input 3 times the projector will turn off. Afterwards the

 

projector will turn off every time an incorrect PASSWORD is input.

 

1.2 Changing the PASSWORD

 

1.2-1Use the ▲/▼ buttons on the SECURITY

 

menu to select SECURITY PASSWORD

 

CHANGE and press the ► button to display

 

the ENTER NEW PASSWORD box.

 

1.2-2Use the ▲/▼/◄/► buttons to enter the new PASSWORD.

 

1.2-3Move the cursor to the right side of the

 

ENTER NEW PASSWORD box and

 

press the ► button to display the NEW

 

PASSWORD AGAIN box, enter the same

 

PASSWORD again.

 

1.2-4Move the cursor to the right side of the NEW

 

PASSWORD AGAIN box and press the ►

 

button and the NOTE NEW PASSWORD

 

box will be displayed for about 20 seconds,

 

please make note of the PASSWORD

 

during this time.

 

Pressing the ENTER button will close the NOTE NEW PASSWORD

 

box.

 

• Please do not forget your PASSWORD.

(continued on next page)

45

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

1.3 If you have forgotten your PASSWORD

 

1.3-1Follow the procedure in1.1-1to display the

 

ENTER PASSWORD box.

 

1.3-2While the ENTER PASSWORD box is

 

displayed, press and hold the RESET

 

button for about 3 seconds or press and

 

hold the INPUT and ► buttons on the

 

projector for about 3 seconds.

 

The 10-digitInquiring Code will be displayed.

 

• If there is no key input for about 55 seconds while the Inquiring Code is

 

displayed the menu will close. If necessary repeat the process from 1.3-1.

 

1.3-3Contact your dealer with the10-digitInquiring Code. Your PASSWORD

 

will be sent after your user registration information is confirmed.

 

2. Using the MyScreen PASSWORD Function

 

The MyScreen PASSWORD function can be used to prohibit access to the

 

MyScreen function and prevent the currently registered MyScreen image

SECURITY

from being overwritten.

2.1 Turning on the MyScreen PASSWORD Function

(continued)

2.1-1Use the ▲/▼ buttons on the SECURITY

 

menu to select MyScreen PASSWORD

 

and press the ► button to display the

 

MyScreen PASSWORD on/off menu.

 

2.2 Setting the PASSWORD

 

2.2-1Display the MyScreen PASSWORD on/off menu using the procedure

 

in 2.1-1.

 

2.2-2Use the ▲/▼ buttons on the MyScreen

 

PASSWORD on/off menu to select TURN ON.

 

The ENTER PASSWORD box (small) will be

 

displayed.

 

2.2-3Use the ▲/▼/◄/► buttons to enter the

 

PASSWORD.

 

Move the cursor to the right side of the ENTER

 

PASSWORD box (small) and press the ►

 

button to display the PASSWORD AGAIN box,

 

enter the same PASSWORD again.

(continued on next page)

46

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

2.2-4Move the cursor to the right side of the

 

PASSWORD AGAIN box and press the

 

► button to display the PASSWORD for

 

about 20 seconds, please make note of the

 

PASSWORD during this time.

 

Pressing the ENTER button will return to

 

MyScreen PASSWORD on/off menu.

 

When a PASSWORD is set for MyScreen:

 

The MyScreen registration function (and menu) will be unavailable.

 

The MyScreen Lock function (and menu) will be unavailable.

 

The START UP setting will be locked on MyScreen (and the menu will

 

be unavailable).

 

Turning the MyScreen PASSWORD off will allow normal operation of both

 

functions.

 

Please do not forget your MyScreen PASSWORD.

 

2.3 Turning the PASSWORD off

 

2.3-1

Follow the procedure in 2.1-1to display the MyScreen PASSWORD

 

 

on/off menu.

 

2.3-2

Select TURN OFF to display the ENTER PASSWORD box (large).

SECURITY

 

Enter the registered PASSWORD and the screen will return to the

 

MyScreen on/off menu.

(continued)

If an incorrect PASSWORD is input the menu will close. If necessary

 

repeat the process from 2.3-1.

2.4 If you have forgotten your PASSWORD

2.4-1Follow the procedure in2.1-1to display the MyScreen PASSWORD on/off menu.

2.4-2Select TURN OFF to display the ENTER PASSWORD box (large). The10-digitInquiring Code will be displayed inside the box.

2.4-3Contact your dealer with the10-digitInquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.

3. Using the PIN LOCK Function

PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.

3.1 Registering the PIN Code

3.1-1Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.

(continued on next page)

47

OPTION menu

OPTION menu (continued)

Item

Description

SECURITY

(continued)

3.1-2Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed.

3.1-3Input a 4 part PIN Code using the ▲, ▼, ◄, ►, COMPUTER and INPUT buttons.

A PIN Code again box will appear. Reenter the same PIN Code. This will complete the PIN Code registration.

If there is no key input for about 55 seconds while the PIN BOX or the PIN Code again box are displayed the menu will close. If necessary repeat the process from3.1-1.

Afterwards, anytime the projector is restarted after AC power is turned off the PIN BOX will be displayed. Enter the registered PIN Code.

The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.

If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.

This function will activate only when the projector is started after AC power is turned off.

Please do not forget your PIN Code.

3.2 Turning Off the PIN LOCK Function

3.2-1Follow the procedure in3.1-1to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.

Enter the registered PIN Code to turn the PIN LOCK function off. If an incorrect PASSWORD is entered the menu will close.

3.3 If you have forgotten your PIN Code

3.3-1While the PIN BOX is displayed, press and hold the RESET button for 3 seconds or press and hold the INPUT and ► buttons for 3 seconds. The10-digitInquiring Code will be displayed.

If it passes for about 5 minutes after the PIN BOX is displayed the projector will turn off.

3.3-2Contact your dealer with the10-digitInquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.

(continued on next page)

48

OPTION menu

OPTION menu (continued)

Item

Description

 

4. Using the Transition Detector Function

 

While the Transition Detector function is ON, when power switch is started

 

to supply to the projector, it might react as below.

 

• Transition Detector alarm shown below might appear on screen, if the

 

projector has been moved or re-installed.

 

• Transition Detector alarm might appear on screen, if the MIRROR setting

 

has been changed.

 

• Keystone adjustment feature has been prohibited as long as the Transition

 

Detector function is ON.

 

4.1 Turning On the Transition Detector Function

 

4.1-1Use the ▲/▼ buttons on the SECURITY

 

menu to select TRANSITION DETECTOR and

 

press the ► or the ENTER button to display

 

the TRANSITION DETECTOR on/off menu.

 

Select TURN ON and the current angle and

 

mirror setting will be recorded.

 

• This feature may not function properly if the projector is not in a stable

 

position when TURN ON is selected.

 

4.1-2If this function is set to TURN ON when

 

the vertical angle of the projector or mirror

SECURITY

setting at which the projector is turned on

is different than the previously recorded the

(continued)

Transition Detector alarm will be displayed

 

and the projector will not display the input

 

signal.

 

Set the Transition Detector off in the SECURITY menu to display the input

 

signal.

 

If the Transition Detector alarm is displayed for about 5 minutes the lamp

 

will turn off. This function will activate only when the projector is started

 

after turning off the AC power.

 

4.2 Setting the Transition Detector PASSWORD

 

4.2-1Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION

 

DETECTOR and press the ► or the ENTER button to display the

 

TRANSITION DETECTOR on/off menu.

 

4.2-2Use the ▲/▼ buttons on the TRANSITION

 

DETECTOR on/off menu to select TURN

 

ON. The ENTER PASSWORD box (small)

 

will be displayed.

 

4.2-3Use the ▲/▼/◄/► buttons to enter a

 

PASSWORD. Move the cursor to the right

 

side of the ENTER PASSWORD box (small)

 

and press the ► button to display the

 

PASSWORD AGAIN box, enter the same

 

PASSWORD again.

(continued on next page)

49

OPTION menu

OPTION menu (continued)

Item

Description

 

 

 

4.2-4Move the cursor to the right side of the

 

PASSWORD AGAIN box and press the

 

► button to display the PASSWORD for

 

about 20 seconds, please make note of the

 

PASSWORD during this time.

 

Pressing the ENTER button will return to the TRANSITION DETECTOR

 

on/off menu.

 

• Please do not forget your Transition Detector PASSWORD.

 

4.3 Setting the Transition Detector off

 

4.3-1Follow the procedure in4.1-1to display the TRANSITION DETECTOR

 

 

on/off menu.

SECURITY

4.3-2

Select TURN OFF to display the ENTER PASSWORD box (large).

(continued)

 

Enter the registered PASSWORD and the screen will return to the

 

TRANSITION DETECTOR on/off menu. If an incorrect PASSWORD is

 

 

 

 

input the menu will close. If necessary repeat the process from 4.3-1.

 

4.4 If you have forgotten your PASSWORD

 

4.4-1

Follow the procedure in 4.1-1to display the TRANSITION DETECTOR

 

 

on/off menu.

 

4.4-2

Select TURN OFF to display the ENTER

 

 

PASSWORD box (large). The 10-digit

 

 

Inquiring Code will be displayed inside the

 

 

box.

 

4.4-3

Contact your dealer with the 10-digitInquiring Code. Your PASSWORD

 

 

will be sent after your user registration information is confirmed.

50

NETWORK menu

NETWORK menu

Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network.

From the NETWORK menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

See the User’s Manual - Network Guide for details of network operation.

NOTE • The factory default setting for DHCP is ON. You do not have to set up DHCP, IP ADDRESS, SUBNET MASK or DEFAULT GATEWAY if your network has DHCP enabled.(User’s Manual - Network Guide)

• If you are not utilizing SNTP (User’s Manual - Network Guide), then you must set the date and time during the initial installation. Please refer to the item DATE AND TIME in the following table(52).

Item

Operation

 

 

 

Use the ▲/▼ buttons to turn DHCP on/off

DHCP

ON OFF

• Select OFF when the network does not

(Dynamic Host

have DHCP enabled.

Configuration

• When the DHCP setting changes to ON, it takes a little time to

Protocol)

obtain IP address from DHCP server.

 

• Auto IP function will be assigned an IP address if the projector

 

could not obtain an IP address from server even if DHCP is ON.

 

Use the ▲/▼/◄/► buttons to enter the IP

 

address. This function can only be used when

 

DHCP is set to OFF.

IP ADDRESS

• The IP address is the number that identifies

this projector on the network. You cannot

 

 

have two devices with the same IP address

 

on the same network.

 

• The IP ADDRESS “0.0.0.0” is prohibited.

 

Use the ▲/▼/◄/► buttons to enter the same

SUBNET MASK

subnet mask used by your PC. This function

can only be used when DHCP is set to OFF.

 

• The SUBNET MASK ”0.0.0.0” is prohibited.

51

NETWORK menu

NETWORK menu (continued)

Item

Operation

 

 

 

 

 

Use the ▲/▼/◄/► buttons to enter the

DEFAULT

default gateway (a node on a computer

network that serves as an access point to

GATEWAY

another network) address.

 

 

This function can only be used when DHCP is set to OFF.

 

Use the ▲/▼ buttons to enter the time

 

difference.

TIME

Set the same time difference as the

one set on your PC. If unsure, consult

DIFFERENCE

your IT manager. Use the ◄ button to

 

 

return to the menu after setting the TIME

 

DIFFERENCE.

 

Use the ▲/▼/◄/► buttons to enter the Year (last two digits),

 

Month, Date, Hour and Minute.

DATE AND TIME

• The projector will override this setting and retrieve the date and

time information from the Time server when SNTP is enabled. (

 

“Date/Time Settings” section of the User’s Manual - Network

 

Guide)

 

Use the ▲/▼ buttons to select an item and the ► or ENTER button

 

to display the image.

 

Image1

 

Image2

 

Image3

 

Image4

 

File names of registered images are

 

 

 

displayed by 16 characters or less.

 

 

 

Example: DEMONSTRATION-01

 

 

 

"NEW" stamp is added to the head of line

 

 

 

when the image is registered newly. After

 

 

 

the image is displayed, "NEW" stamp will

 

 

e-SHOT

be erased. Once an image is displayed,

 

 

 

 

you can use the ▲/▼ buttons to page

 

 

through the images. Use the ◄ or ESC

 

button to return to the menu.

 

Pressing the RESET button on the remote control while an image is

 

being displayed will display the RESET menu. The displayed image

 

can be deleted from the RESET menu using the ENTER button on

 

the remote control or the INPUT button on the projector.

 

If you do not wish to delete the image use the ESC button on the

 

remote control or push the ◄ and INPUT buttons on the projector at

 

the same time.

 

• Items with no image stored cannot be selected.

 

• Images can be changed using the ▲/▼ buttons while the image

 

data downloads.

52

NETWORK menu

NETWORK menu (continued)

Item

Operation

 

 

 

Selecting this item displays the

 

NETWORK -INFORMATION-dialog

 

for confirming the network settings.

Only the first 16 characters of the projector name are displayed.

Nothing (blank) is shown in the NAME field until you setup the

INFORMATION item. For setup, please refer to “Network Settings” section of

User’s Manual - Network Guide.

When the voltage level of the battery for the internal clock decreases, set time may become incorrect even though accurate

date and time are input. Replace a battery through the following the instructions. (57)

IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate “0.0.0.0” when DHCP is ON and the projector has not gotten address from DHCP server.

Executing this item restarts and initializes the network functions.

Choose the RESTART using the button ►.

Then use the button ▲ to execute.

SERVICE

Network will be once cut off when choose restart.

If DHCP is selected on, IP address may be changed.

After selecting RESTART, NETWORK menu may not be controlled approx. 30 seconds.

53

6.
7.

Maintenance

Maintenance

Lamp

A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number : 456-8755G

Replacing the lamp

1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes.

2. Prepare a new lamp.

If the projector is mounted on a ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

3. Loosen the screw (marked by arrow) of the lamp cover and then slide the lamp cover to the side to remove it.

4. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles.

5. Insert the new lamp, and retighten firmly the 2 screws of the lamp that are loosened in the

previous process to lock it in place.

Slide the lamp cover back in place and firmly fasten the screw of the lamp cover.

Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu.

(1) Press the MENU button to display a menu.

Lamp cover

Handles

(2)Point at the Go to Advanced Menu … in the menu using the ▼/▲ button, then press the ► button.

(3)Point at the OPTION in the left column of the menu using the ▼/▲button, then press the ► button.

(4)Point at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.

(5)Press the ▲ button to select RESET on the dialog. It performs resetting the lamp time.

CAUTION ►Do not touch any inner space of the projector, while the lamp is taken out.

NOTE • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

54

Maintenance

Lamp (continued)

Lamp warning

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

WARNING ►The projector uses ahigh-pressuremercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in the US) orwww.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does),

the plug

ventilate the room well, and make sure not to breathe the gas that

from the

comes out of the projector vents, or get it in your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

Never unscrew except the appointed (marked by an arrow) screws.

Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Use only the lamp of the specified type.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

Using the lamp for long periods of time could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

55

Put the filter unit back into the projector.

Maintenance

Air filter

Please check and clean the air filter periodically. When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible. Replace the air filter when it is damaged or too soiled. To prepare a new air filter, contact your dealer and tell the air filter type number.

Type number : MU04951

When you replace the lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector.

Cleaning the air filter

1. Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down.

2. Usecover.a vacuum cleaner on and around the filter3. Pull the filter cover knobs while lifting it. The filter

unit which consists of the filter’ cover, air filter and filter frame will come off.

4. Use a vacuum cleaner for the filter vent of the projector and the filter frame side of the filter unit.

If the air filter is damaged or too soiled, replace it according to the following procedure number 5 to 7. Otherwise, please jump to the procedure number 8. 5. Pull the filter frame’ knob up while holding the filter cover. The filter frame will come off and the air

filter will appear.

6. Replace the air filter with new one.

7. Put the filter frame back.

8.

9. Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU.

Filter cover

Filter cover knobs

Filter unit

Filter frame

Air filter

Filter cover

(1)Press the MENU button to display a menu.

(2)Point at the FILTER TIME using the ▼/▲ button, then press the ► button.Adialog will appear.

(3)Press the ▲ button to select RESET on the dialog. It performs resetting the filter time.

WARNING ►Before taking care of the air filter, make sure the power cord is not plugged in, then allow the projector to cool sufficiently.

►Use only the air filter of the specified type. Do not use the projector without the air filter or the filter cover. It could result in a fire or malfunction to the projector. ►Clean the air filter periodically. If the air filter becomes clogged by dust or the like, internal temperatures rise and could cause a fire, a burn or malfunction to the projector.

NOTE • Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter.

• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

56

Maintenance

Internal clock battery

Consumption of the battery makes the internal clock not to work correctly. When the internal clock is wrong or it has stopped, please replace the battery according to the following procedures.

1. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.

2. After making sure that the projector has cooled adequately, pull the slot cover forward, pushing slightly

its edge up, and remove it from the projector.

3. Remove the battery case.

Hold the battery case gutter by finger nail or other thing and pull out the battery case slowly from the battery slot. While the projector is installed upside down, such as a ceiling mount, please remember the battery will drop down as soon as pulling the battery case out.

4. Take the old battery out from the battery case.

5. Replace a new battery.

Replace battery with HITACHI MAXELL, Part No.CR2032 only. Use of another battery may present a risk of fire or explosion.

Put a new battery into battery case. Please make sure that the + is facing upward. Insert the battery case slowly into the battery slot until you hear the snap.

6. Close the slot cover.

Replace the slot cover by reversing the procedure used when removing the cover.

Slot Cover

Battery Slot

Battery Case

Battery

Battery

Case

Battery (+)

Battery

Case

Battery (-)

WARNING ►Always handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

And also improper use may result in cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not short circuit or solder a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the liquid adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

NOTE • The internal clock’s time will be reset when the battery is removed. Please reconfigure the time via the menu or a web browser after replacing the battery.

("Date/Time Settings" of the User’s Manual - Network Guide)

57

WARNING ►Before caring, make sure the power cord is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so dangerous.
►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and/or malfunction to the projector.
After making sure that the projector is cool adequately, lightly wipe with gauze or a soft cloth.
If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
1.
2.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint, etc.
After making sure that the projector is cool adequately, lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.
Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
1.
2.
Maintenance
Other care
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling.

Do not put anything containing water, cleaners or chemicals near the projector.

Do not use aerosols or sprays.

CAUTION ►Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc.

►Do not use cleaners or chemicals other than those specified in this manual. ►Do not polish or wipe with hard objects.

58

Troubleshooting

Troubleshooting

If an abnormal operation should occur, stop using the projector immediately.

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair.

If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Related messages

When some message appears, check and cope with it according to the following table. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

 

 

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status



 

of the signal source.

SYNC IS OUT OF RANGE

The horizontal or vertical frequency of the input signal

is not within the specified range.



fH kHz fVHz

Please confirm the specs for your projector or the signal

 

source specs.

 

The internal temperature is rising.

 

Please turn the power off, and allow the projector to cool

 

down at least 20 minutes. After having confirmed the

 

following items, please turn the power ON again.

CHECK THE AIR FLOW

• Is there blockage of the air passage aperture?

 

• Is the air filter dirty?

 

• Does the peripheral temperature exceed 35°C?

 

If the same indication is displayed after the remedy, please set

 

FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

REMINDER

A note of precaution when cleaning the air filter.

*** HRS PASSED AFTER THE

Please immediately turn the power off, and clean or change

LAST FILTER CHECK.

the air filter referring to the “Air Filter” section of this manual.

FILTER MAINTENANCE IS ESSENTIAL

After you have cleaned or changed the air filter, please be

TO REMOVE WARNING MESSAGE,

sure to reset the filter timer (56).

RESET FILTER TIMER.

 

SEE MANUAL FURTHER INFO.

 

59

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table.

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

Lighting

Turned

Turned

The projector is in a standby state.

In Orange

off

off

Please refer to the section “Power on/off”.

Blinking

Turned

Turned

The projector is warming up.

In Green

off

off

Please wait.

Lighting

Turned

Turned

The projector is in an on state.

In Green

off

off

Ordinary operations may be performed.

Blinking

Turned

Turned

The projector is cooling down.

In Orange

off

off

Please wait.

 

 

 

The projector is cooling down. A certain error

Blinking

(discre-

(discre-

has been detected.

In Red

tionary)

tionary)

Please wait until POWER indicator finishes blinking,

and then perform the proper measure using the item

 

 

 

descriptions below.

 

 

 

The lamp does not light, and there is a possibility

 

 

 

that interior portion has become heated.

 

 

 

Please turn the power off, and allow the projector to

Blinking

 

 

cool down at least 20 minutes. After the projector has

In Red

Lighting

Turned

sufficiently cooled down, please make confirmation of

or

In Red

off

the following items, and then turn the power on again.

Lighting

• Is there blockage of the air passage aperture?

 

 

In Red

 

 

• Is the air filter dirty?

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy,

 

 

 

please change the lamp referring to the section “Lamp”.

 

 

 

The lamp cover has not been properly fixed.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 45 minutes. After the projector has

In Red

 

 

Blinking

Turned

sufficiently cooled down, please make confirmation of

or

In Red

off

the attachment state of the lamp cover. After performing

Lighting

 

 

any needed maintenance, turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

 

 

 

The cooling fan is not operating.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

 

 

Turned

Blinking

sufficiently cooled down, please make confirmation

or

off

In Red

that no foreign matter has become caught in the fan,

Lighting

 

 

etc., and then turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

(continued on next page)

60

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to cool down at least

Blinking

 

 

20 minutes.After the projector has sufficiently cooled down, please make

In Red

Turned

Lighting

confirmation of the following items, and then turn the power on again.

or

• Is there blockage of the air passage aperture?

Lighting

off

In Red

• Is the air filter dirty?

In Red

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please

 

 

 

set FAN SPEED of SERVICE item in OPTION menu to HIGH

 

 

 

(42).

 

 

 

It is time to clean the air filter.

Lighting

Simultaneous

Please immediately turn the power off, and clean or change

the air filter referring to the section “Air Filter”.After cleaning or

In Green

blinking in Red

changing the air filter, please be sure to reset the filter timer.

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

After the treatment, reset the power to ON.

Blinking in

 

 

At least 1 Power ON schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

Please refer to “Schedule Settings” section of User’s

seconds

 

 

Manual-NetworkGuide.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Shutdown switch

Only when the projector can not be turned off by usual procedure (15), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (44) can reset all settings(except LANGUAGE,

FILTER TIME, LAMP TIME, FILTER MESSAGE, NETWORK settings and etc.) to the

factory default.

61

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

12

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

12, 15

 

Please disconnect the power plug from the power outlet,

Power does not

and allow the projector to cool down at least 10 minutes,

 

then turn the power on again.

 

come on.

 

 

Either there is no lamp and/or lamp cover, or either

 

 

 

 

of these has not been properly fixed.

 

 

Please turn the power off and disconnect the power plug from

54, 55

 

the power outlet, and allow the projector to cool down at least

 

45 minutes. After the projector has sufficiently cooled down,

 

 

please make confirmation of the attachment state of the lamp

 

 

and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

Neither sounds

Signal source does not correctly work.

 

nor pictures are

Correctly set up the signal source device by referring to the

outputted.

manual of the source device.

 

 

The input changeover settings are mismatched.

16, 17

 

Select the input signal, and correct the settings.

 

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the audio cables.

 

 

 

The MUTE function is working.

16

 

Restore the sound pressing MUTE or VOLUME button on

Sound does not

the remote control.

 

come out.

The volume is adjusted to an extremely low level.

16

 

Adjust the volume to a higher level using the menu function

 

or the remote control.

 

 

The AUDIO/SPEAKER setting is not correct.

35

 

Correctly set the AUDIO/SPEAKER in SETUP menu.

 

 

 

The lens cover is attached.

4, 15

No pictures are

Remove the lens cover.

 

displayed.

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

(continued on next page)

62

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The brightness is adjusted to an extremely low level.

25, 26

 

Adjust BRIGHTNESS to a higher level using the menu

 

function.

 

No pictures are

The computer cannot detect the projector as a plug

 

displayed.

and play monitor.

11

(continued)

Make sure that the computer can detect a plug and play

 

 

monitor using another plug and play monitor.

 

 

The BLANK screen is displayed.

21

 

Press BLANK button on the remote control.

 

 

Video screen

The FREEZE function is working.

21

display freezes.

Press FREEZE button to restore the screen to normal.

 

 

Color settings are not correctly adjusted.

25, 26,

Colors have a

Perform picture adjustments by changing the COLOR

fadedout

TEMP, COLOR, TINT and/or COLOR SPACE settings,

31

appearance, or

using the menu functions.

 

Color tone is

COLOR SPACE setting is not suitable.

 

poor.

Change the COLOR SPACE setting to AUTO, RGB,

31

 

SMPTE240, REC709 or REC601.

 

 

The brightness and/or contrast are adjusted to an

 

 

extremely low level.

25, 26

 

Adjust BRIGHTNESS and/or CONTRAST settings to a

 

 

Pictures appear

higher level using the menu function.

 

The WHISPER function is working.

25, 35

dark.

Select NORMAL for WHISPER item in the SETUP menu.

 

 

 

The lamp is approaching the end of its product

 

 

lifetime.

54, 55

 

Replace the lamp.

 

 

Either the focus and/or horizontal phase settings are

 

 

not properly adjusted.

18, 30

Pictures appear

Adjust the focus using the focus ring, and/or H PHASE

 

blurry.

using the menu function.

 

 

The lens is dirty or misty.

58

 

Clean the lens referring to the section “Caring for the lens”.

 

 

NOTE • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect.

63

Specifications

Specifications

Specification

 

Item

 

Specification

 

 

 

 

 

Product name

Liquid crystal projector

 

 

Liquid

 

Panel size

1.6 cm (0.63 type)

 

 

Crystal

 

Drive system

TFT active matrix

 

 

Panel

 

Pixels

786,432 pixels (1024 horizontal x 768 vertical)

 

 

 

Zoom lens,

 

 

Lens

 

 

8755G-RJ

8912-RJ

 

 

F=1.7 ~ 1.9

F=1.7 ~ 1.9

 

 

 

f = 18.9~ 22.6 mm

f = 19.5~ 23.4 mm

 

 

 

 

 

(approximately)

Lamp

 

 

220W UHB

 

 

 

 

 

 

Audio output

7 W

 

 

 

 

 

Power supply

AC 100-120V/3.5A,AC220-240V/1.5A

 

 

 

 

 

Power consumption

320 W

 

 

Temperature range

5 ~ 35°C (Operating)

 

 

Size

 

 

340 (W) x 117 (H) x 270 (D) mm

 

 

 

* Not including protruding parts. Please refer to the following figure.

 

 

 

Weight (mass)

approx. 4.0 kg

 

 

 

 

 

 

 

 

 

 

 

Computer input port

 

 

 

 

 

COMPUTER IN1 ................................

 

D-sub15 pin mini x1

 

 

 

COMPUTER IN2 ................................

 

D-sub15 pin mini x1

 

 

 

Computer output port

 

 

 

 

 

MONITOR OUT ...................................

 

D-sub15 pin mini x1

 

 

 

Video input port

 

 

 

 

 

Y, Cb/Pb, Cr/Pr (Component video) ........................

RCA x3

 

 

 

S-VIDEO...................................................

 

mini DIN 4 pin x1

Ports

 

 

VIDEO .....................................................................

 

RCA x1

 

 

Audio input/output port

 

 

 

 

 

 

 

 

AUDIO IN1.....................................................

 

Stereo mini x1

 

 

 

AUDIO IN2.....................................................

 

Stereo mini x1

 

 

 

AUDIO IN3...............................................................

 

RCA x2

 

 

 

AUDIO OUT...................................................

 

Stereo mini x1

 

 

 

Others

 

 

 

 

 

USB......................................................................

 

USB-Bx1

 

 

 

CONTROL....................................................

 

D-sub9 pin x1

 

 

 

LAN.........................................................................

 

RJ45 x1

 

 

 

Lamp:456-8755G

 

 

Optional parts

Air filter: MU04951

 

 

 

 

 

* For more information, please consult your dealer.

64

Specifications

Specifications (continued)

BATTERY

270

 

340

117

129

[unit: mm]

65

Projector

8755G-RJ/8912-RJ

User’s Manual (detailed)

Network Guide

This manual is only intended to explain Network Functions.

For safety, operations or any other issues, refer to the Safety Guide or Operating Guide.

WARNING • Before using this product, please read the Safety Guide first.

NOTE • The information in this manual is subject to change without notice.

The manufacturer assumes no responsibility for any errors that may appear in this manual.

The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgement

Windows is a registered trademark of Microsoft Corporation.

Netscape is a registered trademark of Netscape Communications Corporation.

JavaScript is a registered trademark of Sun Microsystems, Inc.

All other trademarks are the properties of their respective owners.

Contents

 

Network Functions ..................................................................

2

Configuring and Controlling the Projector via a Web Browser ...

4

E-mailAlerts ..........................................................................

23

Projector Management using SNMP......................................

25

Event Scheduling ...................................................................

26

e-SHOT(Still Image Transfer) Display ..................................

29

Command Control via the Network.......................................

31

1

Network Functions

Network Functions

This projector is equipped with the following network functions.

Configuring and Controlling the Projector via a Web Browser

You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network.

(4)

E-mailAlerts

The projector can automatically send an alert to specified e-mailaddresses when

the projector requires maintenance or has encountered an error.

(23)

Projector Management using SNMP

This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote location using SNMP software. In

addition, the projector is able to send failure & warning alerts to a specified PC.

(25)

Event Scheduling

You can schedule the projector to perform various functions according to the date

and time.

(26)

e-SHOT(Still Image Transfer) Display

The projector can display still images that are transferred via the network.

(29)

Command Control via the Network

The projector can be controlled using RS-232Ccommands over a network.

(31)

Network Functions

Before Using the Network Functions…

To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network.

Connect the gateway (The router/PC that forwards traffic to a destination outside of the subnet of the transmitting device) to the LAN port on the projector using a CAT-5cable and configure the following settings.

If using a network with DHCP enabled:

The projector’s network settings can be configured automatically when DHCP on

the NETWORK menu is set to ON. Please refer to DHCP and INFORMATION in

NETWORK menu ("NETWORK menu" section of the User's Manual - Operating Guide).

If a fixed / static IP address is required, please configure your projector according to the steps in the following section.

If using a network without DHCP enabled

or using a fixed IP address on a network with DHCP enabled:

Configure the following settings on the NETWORK menu ("NETWORK menu" section of the User's Manual - Operating Guide).

1. DHCP : Set DHCP to OFF (disabled).

2. IP ADDRESS : Enter an appropriate IP address for the projector to connect to your network.

3. SUBNET MASK : Enter an appropriate subnet mask for the projector to connect to your network.

4. DEFAULT GATEWAY : Enter an appropriate gateway address for the projector to connect to your network.

Configuring and Controlling the Projector via a Web Browser

Configuring and Controlling the Projector via a Web Browser

You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network.

NOTE • Internet Explorer 5.5 or later or Netscape 6.2 or later are required.

If JavaScript is disabled in your web browser configuration, you must enable JavaScript in order to use the projector web pages properly. See the Help files for your web browser for details on how to enable JavaScript.

If projector is disconnected from network approx. 50 seconds, system will automatically log off. Please Re-logon to continue operations via a web browser.

After you logon, a small, blank window will appear behind the main operation window. Please do not close this small, blank window. If this window is closed, the system will automatically log off after approx. 50 seconds even if an operation is being performed.

The small, blank window will close when the main operation window is closed.

The small, blank window may be considered a pop-upand be blocked if you are using Windows XP Service Pack 2, or using other security software.

If Service Pack 2 blocks the window the following message will appear:

"Pop-upblocked. To see thispop-upor additional options click here..."

Please select "Temporarily Allow Pop-ups"or "Always AllowPop-upsFrom This

Site..." to allow the window to open.

You can communicate using SSL (Secure Socket Layer) if you are using Windows XP Service Pack 2 or earlier versions of Microsoft Windows. Please specify “https://” when you enter the IP address of the projector on the web browser. You can't communicate the projector using SSL on Windows Vista.

It is recommended to install all web browser updates to communicate using SSL. It is especially recommended that users using Internet Explorer install security update Q832894 (MS04-004)or the web browser interface may not be displayed correctly.

And when using an earlier version of Internet Explorer than version 5.5, during operations the browser will log out after 50 seconds.

Configuring and Controlling the Projector via a Web Browser

When configuring or controlling the projector via a web browser, an ID and password are required. There are two types of IDs, Administrator and User. The following chart describes the differences between User and Administrator IDs.

Item

Description

Administrator

User

Network Information

Displays the projector’s current

network configuration settings. (7)

Network Settings

Displays and configures network

N/A

settings. (8)

 

 

 

Port Settings

Displays and configures

N/A

communication port settings. (9)

 

 

 

Mail Settings

Displays and configures e-mail

N/A

addressing settings. (10)

 

 

 

Alert Settings

Displays and configures failure &

N/A

warning alerts. (11)

 

 

 

Schedule Settings

Displays and configures schedule

N/A

 

settings. (13)

 

 

Date/Time Settings

Displays and configures the date and

N/A

 

time settings. (15)

 

 

Security Settings

Displays and configures passwords

N/A

and other security settings. (17)

 

 

 

Projector Control

Controls the projector. (19)

Projector Status

Displays and configures the current

projector status. (22)

 

 

 

Network Restart

Restarts the projector’s network

N/A

connection. (22)

 

 

 

Below are the factory default settings of IDs and passwords for Administrator and User.

Item

ID

Password

 

 

 

Administrator

Administrator

<blank>

User

User

<blank>

Configuring and Controlling the Projector via a Web Browser

Refer to the following for configuring or controlling the projector via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1)

Enter "http://192.168.1.10/"into the

Fig. 1

 

address bar of the web browser and

 

 

press "Enter" key or click "Go" button.

 

 

The screen in Fig. 1 will be displayed.

 

2)

Enter your ID and password and click

 

 

[Logon].

 

If the logon is successful, either the Fig.2 or Fig.3 screen will be displayed.

Fig. 2 (Logon with Administrator ID)

Fig. 3 (Logon with User ID)

main menu

main menu

3)Click the desired operation or configuration item on the main menu located on the left side of the screen.

Configuring and Controlling the Projector via a Web Browser

Network Information

All screen images displayed in this manual are screens of a logon using an Administrator ID. Any Administrator only functions will not be displayed when using a User ID. Refer to the descriptions in each table.

Displays the projector’s current network configuration settings.

Item

Description

 

 

DHCP

Displays the DHCP configuration settings.

IP Address

Displays the current IP address.

Subnet Mask

Displays the subnet mask.

Default Gateway

Displays the default gateway.

MAC Address

Displays the MAC address.

Firmware Date

Displays the network firmware time stamp. This information is only

displayed when logged on using an Administrator ID.

 

Firmware Version

Displays the network firmware version number. This information is

only displayed when logged on using an Administrator ID.

Configuring and Controlling the Projector via a Web Browser

Network Settings

Displays and configures network settings.

 

 

Item

Description

 

 

 

 

IP Configuration

Configures network settings.

 

DHCP ON

Enables DHCP.

 

DHCP OFF

Disables DHCP.

 

 

IP Address

Configures the IP address when DHCP is disabled.

 

 

Subnet Mask

Configures the subnet mask when DHCP is disabled.

 

 

Default Gateway

Configures the default gateway when DHCP is disabled.

 

 

 

Configures the name of the projector.

Projector Name

The length of the Projector Name can be up to 64

alphanumeric characters. Numbers ‘0-9’and alphabet‘a-z’,

 

 

 

 

 

 

‘A-Z’and symbols can be used.

 

 

 

 

 

 

 

Configures the location to be referred to when using SNMP.

sysLocation (SNMP)

The length of the sysLocation can be up to 255 alphanumeric

characters. Only numbers ‘0-9’and alphabet‘a-z’,‘A-Z’can

 

 

 

 

 

 

be used.

 

 

 

Configures the contact information to be referred to when

sysContact (SNMP)

using SNMP.

The length of the sysContact can be up to 255 alphanumeric

 

 

 

characters. Only numbers ‘0-9’and alphabet‘a-z’,‘A-Z’can

 

 

 

be used.

DNS Server Address

Configures the DNS server address.

Click the [Apply] button to save the settings.

NOTE • The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking[Network Restart] on the main menu.

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

Configuring and Controlling the Projector via a Web Browser

Port Settings

Displays and configures communication port settings.

 

Item

Description

 

 

 

Network Control Port1

Configures command control port 1 (Port:23).

(Port:23)

 

 

Port open

Click the [Enable] check box to use port 23.

 

Authentication

Click the [Enable] check box when authentication is required

 

for this port.

 

 

Network Control Port2

Configures command control port 2 (Port:9715).

(Port:9715)

 

 

Port open

Click the [Enable] check box to use port 9715.

 

Authentication

Click the [Enable] check box when authentication is required

 

for this port.

 

 

Image Transfer Port

Configures the image transfer port (Port:9716).

(Port:9716)

 

 

Port open

Click the [Enable] check box to use port 9716.

 

Authentication

Click the [Enable] check box when authentication is required

 

for this port.

 

 

SNMP Port

Configures the SNMP port.

 

Port open

Click the [Enable] check box to use SNMP.

 

Trap address

Configures the destination of the SNMP trap in IP format.

SMTP Port

Configures the SMTP port.

 

Port open

Click the [Enable] check box to use thee-mailfunction.

Click the [Apply] button to save the settings.

NOTE • The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking[Network Restart] on the main menu.

Configuring and Controlling the Projector via a Web Browser

Mail Settings

Displays and configures e-mailaddressing settings.

Item

Description

 

 

 

Click the [Enable] check box to use thee-mailfunction.

Send mail

Configure the conditions for sending e-mailunderAlert

 

Settings.

 

Configures the address of the mail server in IP format.

 

• The address allows not only IP address but also domain

SMTP Server IP Address

name if the valid DNS server is setup in the Network

 

Settings. The maximum length of host or domain name is up

 

to 255 characters.

Sender E-mailaddress

Configures the sender e-mailaddress.

The length of the sender e-mailaddress can be up to 255

 

alphanumeric characters.

 

Configures the e-mailaddress of up to five recipients. You

Recipient E-mailaddress

can also specify [TO] or[CC] for each address. The length of

 

the recipient e-mailaddress can be up to 255 alphanumeric

 

characters.

Click the [Apply] button to save the settings.

NOTE • You can confirm whether the mail settings work correctly using the

[Send Test Mail] button. Please enable Send mail setting before clicking[Send Test Mail].

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

10

Configuring and Controlling the Projector via a Web Browser

Alert Settings

Displays and configures failure & warning alert settings.

Alert Item

Description

 

 

Cover Error

The lamp cover has not been properly fixed.

Fan Error

The cooling fan is not operating.

Lamp Error

The lamp does not light, and there is a possibility that interior

portion has become heated.

 

Temp Error

There is a possibility that the interior portion has become

heated.

 

Air Flow Error

The internal temperature is rising.

Lamp Time Error

Lamp time over.

Cold Error

There is a possibility that the interior portion has become

overcooled.

 

Filter Error

Filter time over.

Other Error

Other error.

If displaying this error, please contact your dealer.

 

Schedule Execution

Schedule Execution error. (13)

Error

 

Lamp Time Alarm

Lamp time over Alarm Time setting.

Filter Time Alarm

Filter time over Alarm Time setting.

Transition Detector

Transition Detector Alarm. ("OPTION menu" section of the

Alarm

User's Manual - Operating Guide)

“CHANGE THE LAMP” is “CHANGE THE LAMP” is displayed.displayed.

Cold Start

The power switch is turned on.

(Off → standby mode)

 

Authentication Failure

The SNMP access is detected from the invalid SNMP

community.

 

Refer to "Troubleshooting" section of the User's Manual - Operating Guidefor further detailed explanation of Error except Other Error and Schedule Execution Error.

11

Configuring and Controlling the Projector via a Web Browser

Alert Settings (Continued)

The Alert Items are shown below.

Setting Item

Description

 

 

Alarm Time

Configures the time to alert.

(Only Lamp Time Alarm and Filter Time Alarm.)

 

SNMP Trap

Click the [Enable] check box to enable SNMP trap alerts.

Send Mail

Click the [Enable] check box to enablee-mailalerts.

(Except Cold Startand Authentication Failure.)

 

 

Configures the subject line of the e-mailto be sent.

Mail Subject

The length of the subject line can be up to 255 alphanumeric

characters.

 

 

(Except Cold Startand Authentication Failure.)

 

Configures the text of the e-mailto be sent.

Mail Text

The length of the text can be up to 1024 alphanumeric

characters.

 

 

(Except Cold Startand Authentication Failure.)

Click the [Apply] button to save the settings.

NOTE • The trigger of Filter Errore-mailis depending on the FILTER MESSAGE setting in the SERVICE item of the OPTION menu which defines the period until filter message is displayed on the projector screen. Thee-mailwill be sent when the filter timer exceeds 50, 100, 200, 300, 400, 500, 600, 700

or 800 hours based on the configuration. No notification e-mailwill be sent if the FILTER MESSAGE is set to TURN OFF. ("OPTION menu" section of the User's Manual - Operating Guide)

Lamp Time Alarm is defined as a threshold for e-mailnotification (reminder) of the lamp timer. When the lamp hour exceeds this threshold that is configured through the Web page, thee-mailwill be sent out.

Filter Time Alarm is defined as a threshold for e-mailnotification (reminder)

of the filter timer. When the filter hour exceeds this threshold, the e-mailwill be sent out.

12

Configuring and Controlling the Projector via a Web Browser

Schedule Settings

Displays and configures schedule settings.

Item

Description

 

 

Daily

Configures the daily schedule.

Sunday

Configures the Sunday schedule.

Monday

Configures the Monday schedule.

Tuesday

Configures the Tuesday schedule.

Wednesday

Configures the Wednesday schedule.

Thursday

Configures the Thursday schedule.

Friday

Configures the Friday schedule.

Saturday

Configures the Saturday schedule.

Specific date No.1

Configures the specific date (No.1) schedule.

Specific date No.2

Configures the specific date (No.2) schedule.

Specific date No.3

Configures the specific date (No.3) schedule.

Specific date No.4

Configures the specific date (No.4) schedule.

Specific date No.5

Configures the specific date (No.5) schedule.

13

Configuring and Controlling the Projector via a Web Browser

Schedule Settings (Continued)

The daily and weekly event items are shown below.

Item

Daily & Weekly Description

 

 

Schedule

Click the [Enable] check box to enable the schedule.

Schedule List

Displays the current schedule.

The specific date event items are shown below.

Item

Specific date (No.1-5)Description

 

 

Schedule

Click the [Enable] check box to enable specific date(No.1-5)

schedule.

 

Date (Month/Day)

Configures the month and day.

Schedule List

Displays the current specific date (No.1-5)schedule.

Click the [Apply] button to save the settings.

To add additional functions and events click the [Add] button and set the following items.

 

Item

Description

 

 

 

Time

Configures the time to execute commands.

Command

Configures the commands to be executed.

Parameter

 

 

Power

Configures the parameters for power control.

 

Input Source

Configures the parameters for input switching.

 

Display Image

Configures the parameters for display of transfer image data.

Click the [Register] button to add new commands to the Schedule List.

Click the [Delete] button to delete commands from the Schedule List.

NOTE • After the projector is moved, check the date and time set for the projector before configuring the schedules. Strong shock may make the date and time settings(15) get out of tune.

14

Configuring and Controlling the Projector via a Web Browser

Date/Time Settings

Displays and configures the date and time settings.

 

 

Item

Description

 

 

 

 

 

Current Date

 

Configures the current date in year/month/day format.

Current Time

 

Configures the current time in hour:minute:second format.

Daylight Savings Time

Click the [ON] check box to enable daylight savings time and

set the following items.

 

 

 

 

 

Start

 

Configures the date and time daylight savings time begins.

 

 

Month

 

Configures the month daylight savings time begins (1~12).

 

 

Week

 

Configures the week of the month daylight savings time

 

 

 

begins (First, 2, 3, 4, Last).

 

 

 

 

 

 

Day

 

Configures the day of the week daylight savings time begins

 

 

 

(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

 

 

 

 

 

 

Time

hour

Configures the hour daylight savings time begins (0 ~ 23).

 

 

 

minute

Configures the minute daylight savings time begins (0 ~ 59).

 

End

 

Configures the date and time daylight savings time ends.

 

 

Month

 

Configures the month daylight savings time ends (1 ~ 12).

 

 

Week

 

Configures the week of the month daylight savings time ends

 

 

 

(First, 2, 3, 4, Last).

 

 

 

 

 

 

Day

 

Configures the day of the week daylight savings time ends

 

 

 

(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

 

 

 

 

 

 

Time

hour

Configures the hour daylight savings time ends (0 ~ 23).

 

 

 

minute

Configures the minute daylight savings time ends (0 ~ 59).

15

Configuring and Controlling the Projector via a Web Browser

Date/Time Settings (Continued)

 

Item

Description

 

 

 

Time difference

Configures the time difference.

Set the same time difference as the one set on your PC. If

 

 

unsure, consult your IT manager.

SNTP

Click the [ON] check box to retrieve Date and Time

information from the SNTP server and set the following items.

 

 

 

 

Configures the SNTP server address in IP format.

 

SNTP Server IP Address

• The address allows not only IP address but also domain name

 

if the valid DNS server is setup in the Network Settings. The

 

 

maximum length of host or domain name is up to 255 characters.

 

Cycle

Configures the interval at which to retrieve Date and Time

 

information from the SNTP server (hours:minutes).

 

 

Click the [Apply] button to save the settings.

NOTE • The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking[Network Restart] on the main menu.

If you connect the projector to an existing network, consult a network administrator before setting server addresses.

To enable the SNTP function, the time difference must be set.

The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled.

The internal clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.

16

Configuring and Controlling the Projector via a Web Browser

Security Settings

Displays and configures passwords and other security settings.

 

Item

Description

 

 

 

Administrator authority

Configures the Administrator ID and password.

 

Administrator ID

Configures the Administrator ID.

 

The length of the text can be up to 32 alphanumeric

 

 

characters.

 

Administrator

Configures the Administrator password.

 

The length of the text can be up to 255 alphanumeric

 

Password

 

characters.

 

 

 

 

 

 

Re-enterAdministrator

Re-enterthe above password for verification.

 

Password

 

User authority

Configures the User ID and password.

 

User ID

Configures the User ID.

 

The length of the text can be up to 32 alphanumeric

 

 

characters.

 

User Password

Configures the User password.

 

The length of the text can be up to 255 alphanumeric

 

 

characters.

 

Re-enterUser

Re-enterthe above password for verification.

 

Password

 

 

17

Configuring and Controlling the Projector via a Web Browser

Security Settings (Continued)

 

Item

Description

 

 

 

Network Control

Configures the authentication password for the command

control.

 

 

 

Authentication

Configures the authentication password.

 

The length of the text can be up to 32 alphanumeric

 

Password

 

characters.

 

 

 

Re-enterAuthentication

Re-enterthe above password for verification.

 

Password

 

SNMP

Configures the community name if SNMP is used.

 

Community Name

Configures the community name.

 

The length of the text can be up to 64 alphanumeric

 

 

characters.

Click the [Apply] button to save the settings.

NOTE • The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking[Network Restart] on the main menu.

• Only numbers ‘0-9’and alphabet‘a-z’,‘A-Z’can be used.

18

Configuring and Controlling the Projector via a Web Browser

Projector Control

The items shown in the table below can be performed using the Projector Control menu. Select an item using the up and down arrow keys on the PC.

Most of the items have a submenu. Refer to the table below for details.

NOTE • The setting value may not match with the actual value if the user changes the value manually. In that case, please refresh the page by clicking

[Refresh] button. Controls the projector.

 

Item

Description

 

 

 

Main

 

 

Power

Turns the power on/off.

 

Input Source

Selects the input source.

 

Picture Mode

Selects the picture mode setting.

 

Blank On/Off

Turns Blank on/off.

 

Mute

Turns Mute on/off.

 

Freeze

Turns Freeze on/off.

 

 

Controls the Magnify setting.

 

 

In some input signal sources, it might stop “Magnify” even

 

Magnify

though it does not reach to maximum setting value.

 

The variable range:

 

 

 

 

• For a computer signal 0-48

 

 

• For a video, s-videoor component video signal0-16

Picture

 

 

Brightness

Adjusts the brightness setting.

 

Contrast

Adjusts the contrast setting.

 

Gamma

Selects the gamma setting.

 

Color Temp

Selects the color temperature setting.

 

Color

Adjusts the color setting.

 

Tint

Adjusts the tint setting.

 

Sharpness

Adjusts the sharpness setting.

 

MyMemory Save

Saves the MyMemory data.

 

MyMemory Recall

Recalls the MyMemory data.

19

Configuring and Controlling the Projector via a Web Browser

Projector Control (Continued)

 

Item

Description

 

 

 

Image

 

 

Aspect

Selects the aspect ratio.

 

Over Scan

Adjusts the over-scansetting.

 

V Position

Adjusts the vertical position.

 

H Position

Adjusts the horizontal position.

 

H Phase

Adjusts the horizontal phase.

 

H Size

Adjusts the horizontal size.

 

Auto Adjust Execute

Performs the automatic adjustment.

Input

 

 

Progressive

Selects the progressive setting.

 

Video NR

Selects the video noise reduction setting.

 

Color Space

Selects the color space setting.

 

Component

Selects the COMPONENT port setting.

 

C-VideoFormat

Selects the video format setting.

 

S-VideoFormat

Selects the s-videoformat setting.

 

Frame Lock

Turns the frame lock function on/off.

 

Computer in-1

Selects the COMPUTER IN1 input signal type.

 

Computer in-2

Selects the COMPUTER IN2 input signal type.

Setup

 

 

Auto Keystone Execute

Performs the automatic keystone distortion correction.

 

Keystone

Adjusts the keystone distortion setting.

 

Whisper

Selects the whisper mode.

 

Mirror

Selects the mirror status.

 

Volume

Adjusts the volume setting.

 

Speaker

Turns the built-inspeaker on/off.

 

Audio-Computer1

Assigns the AUDIO-COMPUTERIN1 input port.

 

Audio-Computer2

Assigns the AUDIO-COMPUTERIN2 input port.

 

Audio-Video

Assigns the AUDIO-VIDEOinput port.

 

Audio-S-Video

Assigns the AUDIO-S-VIDEOinput port.

 

Audio-Component

Assigns the AUDIO-COMPONENTinput port.

20

 

Configuring and Controlling the Projector via a Web Browser

Projector Control (Continued)

 

 

 

 

Item

Description

 

 

 

Screen

 

 

Language

Selects the language for the OSD.

 

Menu Position V

Adjusts the vertical Menu position.

 

Menu Position H

Adjusts the horizontal Menu position.

 

Blank

Selects the Blank mode.

 

Startup

Selects the start-upscreen mode.

 

MyScreen Lock

Turns MyScreen lock function on/off.

 

Message

Turns the message function on/off.

Option

 

 

Auto Search

Turns the automatic signal search function on/off.

 

Auto Keystone

Turns the automatic keystone distortion correction function on/off.

 

Auto on

Turns the AUTO ON function on/off.

 

Auto off

Configures the timer to shut off the projector when no signal

 

is detected.

 

 

 

My Button-1

Assigns the function for the MY BUTTON1 button on the

 

included remote control.

 

 

 

My Button-2

Assigns the function for the MY BUTTON2 button on the

 

included remote control.

 

 

 

Remote Freq. Normal

Enables/Disables remote control signal frequency normal.

 

Remote Freq. High

Enables/Disables remote control signal frequency high.

21

Configuring and Controlling the Projector via a Web Browser

Projector Status

Displays and configures the current projector status.

Item

Description

 

 

Error Status

Displays the current error status.

Lamp Time

Displays the usage time for the current lamp.

Filter Time

Displays the usage time for the current filter.

Power Status

Displays the current power status.

Input Status

Displays the current input signal source.

Blank On/Off

Displays the current Blank on/off status.

Mute

Displays the current Mute on/off status.

Freeze

Displays the current Freeze status.

Network Restart

Restarts the projector’s network connection.

Item

Description

 

 

Restart

Restarts the projector’s network connection in order to

activate new configuration settings.

 

NOTE • Restarting requires you tore-logonin order to further control or configure the projector via a web browser. Wait 1 minute or more after clicking[Restart] button to log on again in order to further control or configure the projector via a web browser.

• A link to the logon screen (6 : Fig. 1) is displayed after restarting the projector's network connection if the DHCP is set to ON.

Logoff

22

When [Logoff] is clicked, the logon screen is displayed (6 : Fig. 1).

 

E-mailAlerts

E-mailAlerts

The projector can automatically send an alert message to the specified e-mailaddresses when the projector detects a certain condition that is requiring maintenance or detected an error.

NOTE • Up to fivee-mailaddresses can be specified.

• The projector may be not able to send e-mailif the projector suddenly loses power.

Mail Settings

To use the projector’s e-mailalert function please configure the following items through a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

2)Enter the Administrator ID and password and click [Logon].

3)Click [Port Settings] on the main menu.

4)Click the [Enable] check box to open theSMTP Port.

5)Click the [Apply] button to save the settings.

NOTE • A Network Restart is required after theSMTP Port configuration settings have changed. Click[Network Restart] and configure the following items.

6)Click [Mail Settings] and configure each item. Refer to theMail Settings

item in "Configuring and Controlling the Projector via a Web Browser"for further information (10).

7)Click the [Apply] button to save the settings.

NOTE • Click the[Send Test Mail] button inMail Settings to confirm that thee-mailsettings are correct. The following mail will be delivered to the specified addresses.

Subject line : Test Mail

<Projector name>

Text

: Send Test Mail

 

 

Date

<Testing date>

 

Time

<Testing time>

 

IP Address

<Projector IP address>

 

MAC Address

<Projector MAC address>

23

E-mailAlerts

Mail Settings (Continued)

8)Configure the Failure/Warning Alerts via E-mailsettings. Click[Alert Settings] on the main menu.

9)Select and configure each alert item. Refer to Alert Settings in"Configuring

and Controlling the Projector via a Web Browser" for further information (

11).

10) Click the [Apply] button to save the settings.

Failure/Warning e-mailsare formatted as follows:

Subject line : <Mail title>

<Projector name>

Text

: <Mail text>

 

 

Date

<Failure/Warning date>

 

Time

<Failure/Warning time>

 

IP Address

<Projector IP address>

 

MAC Address

<Projector MAC address>

24

Projector Management using SNMP

Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function.

NOTE • It is recommended that SNMP functions be carried out by a network administrator.

• SNMP management software must be installed on the computer to monitor the projector via SNMP.

SNMP Settings

Configure the following items via a web browser to use SNMP.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

2)Enter the Administrator ID and password and click [Logon].

3)Click [Port Settings] on the main menu.

4)Click the [Enable] check box to open theSNMP Port.

Set the IP address to send the SNMP trap to when a Failure/Warning occurs.

NOTE • A Network Restart is required after theSNMP Port configuration settings have been changed. Click[Network Restart] and configure the following items.

5)Click [Security Settings] on the main menu.

6)Click [SNMP] and set theCommunity Name on the screen that is displayed.

NOTE • A Network Restart is required after theCommunity Name has been changed. Click[Network Restart] and configure the following items.

7)Configure the settings for Trap transmission of Failures/Warnings. Click

[Alert Settings] on the main menu and select the Failure/Warning item to be configured.

8)Click the [Enable] check box to send out the SNMP trap for Failures/Warnings. Clear the[Enable] check box when SNMP trap transmission is not required.

9)Click the [Apply] button to save the settings.

25

Event Scheduling

Event Scheduling

The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management”projector.

NOTE • You can schedule the following control events: Power ON/OFF, Input

Source and Transferred Image Display.

The power on / off event has the lowest priority among the all events that are defined at the same time.

There are 3 types of Scheduling, 1) Daily 2) Weekly 3) Specific date (27).

The priority for scheduled events is as follows 1) Specific date 2) Weekly

3) Daily.

Up to five specific dates are available for scheduled events. Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time (e.g., ‘Specific date No. 1’ has priority over ‘Specific date No. 2’ and so on).

Be sure to set the date and time before enabling scheduled events (28).

26

Event Scheduling

Schedule Settings

Schedule settings can be configured from a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

2)Enter the Administrator ID and password and click [Logon].

3)Click [Schedule Settings] on the main menu and select the required schedule item. For example, if you want to perform the command every Sunday, please select the[Sunday].

4)Click the [Enable] check box to enable scheduling.

5)Enter the date (month/day) for specific date scheduling.

6)Click the [Apply] button to save the settings.

7)Click [Add] to create new event. After configure the time, command and parameters, click[Register] to add the new event. To return the previous page, click[Cancel] button.

8)Click the [Delete] button when you want to delete a schedule.

There are three types of scheduling.

1)Daily: Perform the specified operation at a specified time every day.

2)Weekly (Sunday ~ Saturday): Perform the specified operation at the specified time on a specified day of the week.

3)Specific date: Perform the specified operation on the specified date and time.

NOTE • In Standby mode the POWER indicator will flash green for approx. 3 seconds when at least 1 “Power ON” schedule is saved.

• When the schedule function is used, the power cord must be connected to the projector and the outlet and the power switch must be turned on, [ | ]. The schedule function does not work when the power switch is turned off, [ ¡ ] or the breaker in a room is tripped. The POWER indicator will lights orange or green when the projector is receiving the power.

27

Event Scheduling

Date/Time Settings

The Date/Time setting can be adjusted via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

Enter the Administrator ID and password and click [Logon].

2)Click [Date/Time Settings] on the main menu and configure each item.

Refer to the Date/Time Settingsitem in "Configuring and Controlling the

Projector via a Web Browser" for further information.

3)Click the [Apply] button to save the settings.

NOTE • A Network Restart is required after theDaylight Savings Time orSNTP configuration settings have been changed.

The battery for the built in clock may be dead if the clock loses time even when the date and time have been set correctly. Replace the battery by

following the instructions on replacing the battery.

("Internal clock battery" section of the User's Manual - Operating Guide)

The internal clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.

28

e-SHOT(Still Image Transfer) Display

e-SHOT(StillImageTransfer) Display

The projector can display a still image that is transferred via the network.

Communication Port

The following port is used for e-SHOT.

TCP #9716

NOTE e-SHOTis not available via communication ports (TCP #23 and TCP #9715) (9) which are used for the command control.

e-SHOT(Still Image Transfer) Settings

Configure the following items from a web browser when e-SHOTis used.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

2)Enter the Administrator ID and password and click [Logon].

3)Click [Port Settings] on the main menu.

4)Click the [Enable] check box to open the

Image Transfer Port (Port: 9716). Click the [Enable]check box for the [Authentication]setting when authentication is required, otherwise clear the check box.

5)Click the [Apply] button to save the settings.

29

e-SHOT(Still Image Transfer) Display

e-SHOT(Still Image Transfer) Settings (Continued)

When the authentication setting is enabled, the following settings are required.

6)Click [Security Settings] on the main menu.

7)Select [Network Control] and enter the desired authentication password.

8)Click the [Apply] button to save the settings.

NOTE • The Authentication Password will be the same forNetwork Control

Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer Port (Port: 9716).

• The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking

[Network Restart] on the main menu.

e-SHOT(Still Image Transfer) Transmission

e-SHOTtransmission requires an exclusive application for your PC. You can download it from the Hitachi web site. Refer to the manual for the application for instructions.

To display the transferred image, select the e-SHOTitem in the NETWORK menu

("NETWORK menu" section of the User's Manual - Operating Guide).

NOTE • It is possible to allocate the image file up to 4 in the maximum.

• The image file also can be displayed by using schedule function from the web browser. Refer to "Event Scheduling" (26) in detail.

30

Command Control via the Network

Command Controlvia the Network

You can configure and control the projector via the network using RS-232Ccommands.

Communication Port

The following two ports are assigned for the command control.

TCP #23

TCP #9715

NOTE • Command control is not available via communication port (TCP #9716) (9) that is used for thee-SHOTtransmission function.

Command Control Settings

Configure the following items from a web browser when command control is used.

Example: If the IP address of the projector is set to 192.168.1.10:

1)Enter "http://192.168.1.10/" into the address bar of the web browser.

2)Enter the Administrator ID and password and click [Logon].

3)Click [Port Settings] on the main menu.

4)Click the [Enable]check box to open Network Control Port1 (Port: 23)to use

TCP #23. Click the [Enable] check box for the[Authentication] setting when authentication is required, otherwise clear the check box.

5)Click the [Enable]check box to open Network Control Port2 (Port: 9715)to use TCP #9715. Click the [Enable]check box for the [Authentication]setting when authentication is required, otherwise clear the check box.

6)Click the [Apply] button to save the settings.

31

Command Control via the Network

Command Control Settings (Continued)

When the authentication setting is enabled, the following settings are required.

(17)

7)Click [Security Settings] on the main menu.

8)Click [Network Control] and enter the desired authentication password.

9)Click the [Apply] button to save the settings.

NOTE • The Authentication Password will be the same forNetwork Control

Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer Port (Port: 9716).

• The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking

[Network Restart] on the main menu.

32

Command Control via the Network

Command Format

Command formats differ among the different communication ports.

● TCP #23

You can use the RS-232Ccommands without any changes. The reply data format is the same as theRS-232Ccommands. However, the following reply will be sent back in the event of authentication failure when authentication is enabled.

<Reply in the event of an authentication error>

Reply

Error code

 

 

 

0x1F

0x04

0x00

● TCP #9715

Send Data format

The following formatting is added to the header (0x02), Data length (0x0D), Checksum (1byte) and Connection ID (1 byte) of the RS-232Ccommands.

Header

Data

RS-232Ccommand

Checksum

Connection

 

length

 

 

ID

 

 

 

 

 

0x02

0x0D

13 bytes

1 byte

1 byte

Header

 

→ 0x02, Fixed

 

 

Data length

RS-232Ccommands byte length (0x0D, Fixed)

RS-232Ccommands →RS-232Ccommands that start with 0xBE 0xEF (13 bytes)

Check Sum

→ This is the value to make zero on the addition of the

 

lower 8 bits from the header to the checksum.

Connection ID

→ Random value from 0 to 255 (This value is attached to

 

the reply data)

33

Command Control via the Network

Command Format (Continued)

Reply Data format

The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232Ccommands reply data.

<ACK reply>

 

Reply

 

Connection

 

 

 

 

ID

 

 

 

 

 

 

 

 

 

 

 

 

 

0x06

 

1 byte

 

 

<NAK reply>

 

 

 

 

 

 

 

 

 

Reply

 

Connection

 

 

 

 

ID

 

 

 

 

 

 

 

 

 

 

 

 

 

0x15

 

1 byte

 

 

<Error reply>

 

 

 

 

 

 

 

 

Reply

 

Error code

Connection

 

 

ID

 

 

 

 

 

 

 

 

 

 

0x1C

 

2 bytes

1 byte

<Data reply>

 

 

 

 

 

 

 

 

 

 

Reply

 

Data

Connection

 

 

ID

 

 

 

 

 

 

 

 

 

 

0x1D

 

2 bytes

1 byte

<Projector busy reply>

Reply

Status code

Connection

ID

 

 

 

 

 

0x1F

2 bytes

1 byte

<Authentication error reply>

Reply

Authentication

Connection

Error code

ID

 

 

 

 

 

0x1F

0x04

0x00

1 byte

34

Command Control via the Network

Automatic Connection Break

The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established.

Authentication

The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm.

When the projector is using a LAN, a random 8 bytes will be returned if authentication is enabled. Bind this received 8 bytes and the Authentication Password and digest this data with the MD5 algorithm and add this in front of the commands to send.

Following is a sample if the Authentication Password is set to “password” and the random 8 bytes are “a572f60c”.

1)Select the projector.

2)Receive the random 8 bytes “a572f60c” from the projector.

3)Bind the random 8 bytes “a572f60c” and the Authentication Password “password” and it becomes “a572f60cpassword”.

4)Digest this bind “a572f60cpassword” with MD5 algorithm. It will be “e3d97429adffa11bce1f7275813d4bde”.

5)Add this “e3d97429adffa11bce1f7275813d4bde” in front of the commands and send the data.

Send “e3d97429adffa11bce1f7275813d4bde”+command.

6)When the sending data is correct, the command will be performed and the reply data will be returned. Otherwise, an authentication error will be returned.

NOTE • As for the transmission of the second or subsequent commands, the authentication data can be omitted when the same connection.

35

Projector

8755G-RJ/8912-RJ

User's Manual (detailed)

Technical

Example of PC signal

Resolution (H x V)

H. frequency (kHz)

V. frequency (Hz)

Rating

Signal mode

 

 

 

 

 

 

 

 

 

 

720 x 400

37.9

85.0

VESA

TEXT

640 x 480

31.5

59.9

VESA

VGA (60Hz)

640 x 480

37.9

72.8

VESA

VGA (72Hz)

640 x 480

37.5

75.0

VESA

VGA (75Hz)

640 x 480

43.3

85.0

VESA

VGA (85Hz)

800 x 600

35.2

56.3

VESA

SVGA (56Hz)

800 x 600

37.9

60.3

VESA

SVGA (60Hz)

800 x 600

48.1

72.2

VESA

SVGA (72Hz)

800 x 600

46.9

75.0

VESA

SVGA (75Hz)

800 x 600

53.7

85.1

VESA

SVGA (85Hz)

832 x 624

49.7

74.5

 

Mac 16” mode

1024 x 768

48.4

60.0

VESA

XGA (60Hz)

1024 x 768

56.5

70.1

VESA

XGA (70Hz)

1024 x 768

60.0

75.0

VESA

XGA (75Hz)

1024 x 768

68.7

85.0

VESA

XGA (85Hz)

1152 x 864

67.5

75.0

VESA

1152 x 864 (75Hz)

1280 x 960

60.0

60.0

VESA

1280 x 960 (60Hz)

1280 x 1024

64.0

60.0

VESA

SXGA (60Hz)

1280 x 1024

80.0

75.0

VESA

SXGA (75Hz)

1280 x 1024

91.1

85.0

VESA

SXGA (85Hz)

1600 x 1200

75.0

60.0

VESA

UXGA (60Hz)

1280 x 768

47.7

60.0

VESA

W-XGA(60Hz)

1400 x 1050

65.2

60.0

VESA

SXGA+ (60Hz)

NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC.

Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

Depending on the input signal, full-sizedisplay may not be possible in some cases. Refer to the number of display pixels above.

Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical.

Automatically adjustment may not function correctly with some input signals.

The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G.

1

Initial set signals

Initialset signals

The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in IMAGE menu.

Back porch (B)

Front porch (D)

 

 

 

 

 

 

 

Data

 

 

Active video (C)

 

 

 

 

 

 

 

 

 

 

 

H. Sync.

 

 

 

 

 

 

 

 

Sync (A)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

computer

Horizontal signal timing (μs)

Signal

(A)

(B)

(C)

(D)

 

 

 

 

 

 

 

 

 

TEXT

2.0

3.0

20.3

1.0

 

VGA (60Hz)

3.8

1.9

25.4

0.6

 

VGA (72Hz)

1.3

4.1

20.3

0.8

 

VGA (75Hz)

2.0

3.8

20.3

0.5

 

VGA (85Hz)

1.6

2.2

17.8

1.6

 

SVGA (56Hz)

2.0

3.6

22.2

0.7

 

SVGA (60Hz)

3.2

2.2

20.0

1.0

 

SVGA (72Hz)

2.4

1.3

16.0

1.1

 

SVGA (75Hz)

1.6

3.2

16.2

0.3

 

SVGA (85Hz)

1.1

2.7

14.2

0.6

 

Mac 16" mode

1.1

3.9

14.5

0.6

 

XGA (60Hz)

2.1

2.5

15.8

0.4

 

XGA (70Hz)

1.8

1.9

13.7

0.3

 

XGA (75Hz)

1.2

2.2

13.0

0.2

 

XGA (85Hz)

1.0

2.2

10.8

0.5

 

1152 x 864

1.2

2.4

10.7

0.6

 

(75Hz)

 

 

 

 

 

 

 

 

1280 x 960

1.0

2.9

11.9

0.9

 

(60Hz)

 

 

 

 

 

 

 

 

SXGA (60Hz)

1.0

2.3

11.9

0.4

 

SXGA (75Hz)

1.1

1.8

9.5

0.1

 

SXGA (85Hz)

1.0

1.4

8.1

0.4

 

UXGA (60Hz)

1.2

1.9

9.9

0.4

 

W-XGA(60Hz)

1.7

2.5

16.0

0.8

 

SXGA+ (60Hz)

1.2

2.0

11.4

0.7

 

Back porch (b)

 

Front porch (d)

 

 

 

 

 

 

 

 

 

 

 

 

Data

 

 

 

 

Active video (c)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V. Sync.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sync (a)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

computer

Vertical signal timing (lines)

Signal

(a)

(b)

 

(c)

 

(d)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEXT

3

42

 

400

1

 

 

VGA (60Hz)

2

33

 

480

10

 

 

VGA (72Hz)

3

28

 

480

9

 

 

VGA (75Hz)

3

16

 

480

1

 

 

VGA (85Hz)

3

25

 

480

1

 

 

SVGA (56Hz)

2

22

 

600

1

 

 

SVGA (60Hz)

4

23

 

600

1

 

 

SVGA (72Hz)

6

23

 

600

37

 

 

SVGA (75Hz)

3

21

 

600

1

 

 

SVGA (85Hz)

3

27

 

600

1

 

 

Mac 16" mode

3

39

 

624

1

 

 

XGA (60Hz)

6

29

 

768

3

 

 

XGA (70Hz)

6

29

 

768

3

 

 

XGA (75Hz)

3

28

 

768

1

 

 

XGA (85Hz)

3

36

 

768

1

 

 

1152 x 864

3

32

 

864

1

 

 

(75Hz)

 

 

 

 

 

 

 

 

 

 

 

 

 

1280 x 960

3

36

 

960

1

 

 

(60Hz)

 

 

 

 

 

 

 

 

 

 

 

 

 

SXGA(60Hz)

3

38

 

1024

1

 

 

SXGA (75Hz)

3

38

 

1024

1

 

 

SXGA (85Hz)

3

44

 

1024

1

 

 

UXGA (60Hz)

3

46

 

1200

1

 

 

W-XGA(60Hz)

3

23

 

768

1

 

 

SXGA+ (60Hz)

3

33

 

1050

1

 

 

Connection to the ports

Connection to the ports

LAN

B C

A

A COMPUTER IN1,B COMPUTER IN2,C MONITOR OUT

D-sub15pin mini shrink jack

Video signal: RGB separate, Analog, 0.7Vp-p,75Ω terminated (positive)

H/V. sync. Signal: TTL level (positive/negative)

Composite sync. Signal: TTL level

Pin

Signal

Pin

Signal

 

 

 

 

1

Video Red

10

Ground

2

Video Green

11

(No connection)

3

Video Blue

12

A : SDA (DDC data)

4

(No connection)

B , C : (No connection)

 

5

Ground

13

H. sync / Composite sync.

6

Ground Red

14

V. sync.

7

Ground Green

15

A : SCL (DDC clock)

8

Ground Blue

B , C : (No connection)

 

9

(No connection)

-

-

Connection to the ports (continued)

LAN

D E F G

H

COMPONENT VIDEO D Y,E Pb/Cb,F Pr/Cr

RCA jack x3

• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p),1125i(1080i)

Port

Signal

 

 

Y

Component video Y, 1.0±0.1Vp-p,75Ω terminator with composite

Pb/Cb

Component video Pb/Cb, 0.7±0.1Vp-p,75Ω terminator

Pr/Cr

Component video Pr/Cr, 0.7±0.1Vp-p,75Ω terminator

G S-VIDEO

Mini DIN 4pin jack

1

2

3

4

Pin

Signal

1Color signal 0.286Vp-p(NTSC, burst), 75Ω terminator Color signal0.300Vp-p(PAL/SECAM, burst) 75Ω terminator

2Brightness signal, 1.0Vp-p,75Ω terminator

3Ground

4Ground

H VIDEO

RCA jack

System: NTSC, PAL, SECAM, PAL-M,PAL-N,NTSC4.43

1.0±0.1Vp-p,75Ω terminator

Connection to the ports (continued)

LAN

I M

J

K L

I AUDIO IN1,J AUDIO IN2

Ø3.5 stereo mini jack

• 200 mVrms 47kΩ terminator

AUDIO IN3 K L,L R

RCA jack x2

• 200 mVrms 47kΩ terminator

M AUDIO OUT

Ø3.5 stereo mini jack

• 200 mVrms 1kΩ output impedance

To input SCART RGB signal; ex.:

SCART connector (jack)

SCART cable

(plug)

RCA plugs

To input SCART RGB signal to the projector, use a SCART to RCA cable.

Connect the plugs refer to above ex.. For more reference, please consult your dealer.

Connection to the ports (continued)

P LAN

O

N

N USB

4

3

 

 

USB B type jack

 

 

Pin

Signal

1

2

 

 

1

+5V

 

 

2

- Data

 

 

3

+ Data

 

 

4

Ground

 

 

O CONTROL

D-sub9pin plug

• About the details of RS-232Ccommunication, please refer to the following page.

9 8 7 6

5 4 3 2 1

Pin

Signal

Pin

Signal

Pin

Signal

 

 

 

 

 

 

1

(No connection)

4

(No connection)

7

RTS

2

RD

5

Ground

8

CTS

3

TD

6

(No connection)

9

(No connection)

P LAN

RJ-45jack

 

1

 

2

 

3

4

5

6

7

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Signal

Pin

Signal

Pin

Signal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

TX +

4

-

7

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

TX -

5

-

8

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

RX +

6

RX -

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.
2.

RS-232CCommunication

RS-232CCommunication

1

2

3

4

5

1

2

3

4

5

6

7

8

 

9

6

7

8

 

9

CONTROL port

RS-232Ccable (cross)

RS-232Cport

of the projector

- (1)

(1)

CD

of the computer

 

 

 

RD (2)

(2)

RD

 

 

TD (3)

 

(3) TD

 

 

- (4)

(4)

DTR

 

 

GND (5)

 

(5) GND

 

 

 

 

 

- (6)

(6)

DSR

 

 

RTS (7)

(7)

RTS

 

 

CTS (8)

(8)

DTS

 

 

- (9)

(9)

RI

 

Connecting the cable

Turn off the projector and the computer.

Connect the CONTROL port of the projector with a RS-232Cport of the computer by aRS-232Ccable (cross). Use the cable that fulfills the

specification shown in the previous page.

3. Turn the computer on, and after the computer has started up turn the projector on.

Communications setting

19200bps, 8N1

1. Protocol

Consist of header (7 bytes) + command data (6 bytes)

2. Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low: Lower byte of CRC flag for command data CRC_high: Upper byte of CRC flag for command data

3. Command data

Command data chart

byte_0

byte_1

 

byte_2

byte_3

 

byte_4

 

byte_5

 

Action

 

 

Type

 

Setting code

 

low

high

 

low

high

 

low

 

high

 

Action (byte_0 - 1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Action

Classification

 

 

Content

 

 

1

Set

 

Change setting to desired value.

 

2

Get

 

Read projector internal setup value.

 

4

Increment

 

Increment setup value by 1.

 

 

5

Decrement

 

Decrement setup value by 1.

 

 

6

Execute

 

Run a command.

 

 

RS-232CCommunication (continued)

Requesting projector status (Get command)

(1)Send the following request code from the PC to the projector.

Header + Command data (‘02H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)

(2)The projector returns the response code ‘1DH’ + data (2 bytes) to the PC.

Changing the projector settings (Set command)

(1)Send the following setting code from the PC to the projector.

Header + Command data (‘01H’ + ‘00H’ + type (2 bytes) + setting code (2 bytes))

(2)The projector changes the setting based on the above setting code.

(3)The projector returns the response code ‘06H’ to the PC.

Using the projector default settings (Reset Command)

(1)The PC sends the following default setting code to the projector.

Header + Command data (‘06H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)

(2)The projector changes the specified setting to the default value.

(3)The projector returns the response code ‘06H’ to the PC.

Increasing the projector setting value (Increment command)

(1)The PC sends the following increment code to the projector.

Header + Command data (‘04H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)

(2)The projector increases the setting value on the above setting code.

(3)The projector returns the response code ‘06H’ to the PC.

Decreasing the projector setting value (Decrement command)

(1)The PC sends the following decrement code to the projector.

Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)

(2)The projector decreases the setting value on the above setting code.

(3)The projector returns the response code ‘06H’ to the PC.

When the projector cannot understand the received command

When the projector cannot understand the received command, the error code ‘15H’ is sent back to the PC.

Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code ‘15H’ is sent back to the PC. If this error code is returned, send the same command again.

When the projector cannot execute the received command.

When the projector cannot execute the received command, the error code ‘1CH’ + ‘xxxxH’ is sent back to the PC.

When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the PC.

NOTE • Operation cannot be guaranteed when the projector receives an undefined command or data.

Provide an interval of at least 40ms between the response code and any other code.

The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.

Commands are not accepted during warm-up.

RS-232CCommunication (continued)

RS-232Ccommunication command table

Names 

 

Operation Type

 

 

 

Header

 

 

 

 

 

 

 

 

 

 

Command Data

 

 

 

 

 

 

 

 

CRC

 

 

Action

 

Type

 

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

Set

Turn off

BE EF

 

03

06 00

 

 

 

2A

D3

 

 

01 00

 

00 60

 

00 00

 

 

Turn on

BE EF

 

03

06 00

 

 

 

BA D2

 

 

01 00

 

00 60

 

01 00

 

 

Get

BE EF

 

03

06 00

 

 

 

19 D3

 

 

02 00

 

00 60

 

00 00

 

 

 

[Example return] 

01

00

 

 

 

 

02

00 

 

 

 

 

 

 

 

 

00

00

 

 

 

 

 

 

 

 

 

 

 

 

[Off]

[On]

 

 

 

[Cool down]

 

 

 

 

Input Source

Set

COMPUTER1

BE EF

 

03

06 00

 

 

 

FE D2

 

 

01 00

 

00 20

 

00 00

 

 

COMPUTER2

BE EF

 

03

06 00

 

 

 

3E

D0

 

 

01 00

 

00 20

 

04 00

 

 

COMPONENT

BE EF

 

03

06 00

 

 

 

AE D1

 

 

01 00

 

00 20

 

05 00

 

 

S-VIDEO

BE EF

 

03

06 00

 

 

 

9E

D3

 

 

01 00

 

00 20

 

02 00

 

 

VIDEO

BE EF

 

03

06 00

 

 

 

6E

D3

 

 

01 00

 

00 20

 

01 00

 

 

Get

BE EF

 

03

06 00

 

 

 

CD D2

 

 

02 00

 

00 20

 

00 00

Error Status

 

Get

BE EF

 

03

06 00

 

 

 

D9

D8

 

 

02 00

 

20 60

 

00 00

 

 

 

[Example return] 

01

00

 

 

 

 

02

00

 

 

03

00 

 

 

 

 

00

00

 

 

 

 

 

 

 

 

 

 

[Normal]

[Cover error]

 

 

[Fan error]

 

[Lamp error] 

 

 

 

 

04

00

05

00

 

 

 

 

06

00

 

 

07

00 

 

 

 

[Temp error]

[Air flow error]

 

[Lamp time error]

 

[Cold error] 

 

 

 

 

08 00

09 00

 

 

 

 

10 00 

 

 

 

 

 

 

 

[Filter error]

(Filter missing error) (Inner Sencer error)

 

 

 

BRIGHTNESS

 

Get

BE EF

 

03

06 00

 

 

 

89 D2

 

 

02 00

 

03 20

 

00 00

 

 

Increment

BE EF

 

03

06 00

 

 

 

EF D2

 

 

04 00

 

03 20

 

00 00

 

 

Decrement

BE EF

 

03

06 00

 

 

 

3E

D3

 

 

05 00

 

03 20

 

00 00

BRIGHTNESS Reset

 

Execute

BE EF

 

03

06 00

 

 

 

58 D3

 

 

06 00

 

00 70

 

00 00

CONTRAST

 

Get

BE EF

 

03

06 00

 

 

 

FD D3

 

 

02 00

 

04 20

 

00 00

 

 

Increment

BE EF

 

03

06 00

 

 

 

9B

D3

 

 

04 00

 

04 20

 

00 00

 

 

Decrement

BE EF

 

03

06 00

 

 

 

4A

D2

 

 

05 00

 

04 20

 

00 00

CONTRAST Reset

 

Execute

BE EF

 

03

06 00

 

 

 

A4

D2

 

 

06 00

 

01 70

 

00 00

PICTURE MODE

Set

NORMAL

BE EF

 

03

06 00

 

 

 

23

F6

 

 

01 00

 

BA 30

 

00 00

 

 

CINEMA

BE EF

 

03

06 00

 

 

 

B3 F7

 

 

01 00

 

BA 30

 

01 00

 

 

DYNAMIC

BE EF

 

03

06 00

 

 

 

E3 F4

 

 

01 00

 

BA 30

 

04 00

 

 

BOARD(BLACK)

BE EF

 

03

06 00

 

 

 

E3

EF

 

 

01 00

 

BA 30

 

20 00

 

 

BOARD(GREEN)

BE EF

 

03

06 00

 

 

 

73 EE

 

 

01 00

 

BA 30

 

21 00

 

 

WHITEBOARD

BE EF

 

03

06 00

 

 

 

83 EE

 

 

01 00

 

BA 30

 

22 00

 

 

DAYTIME

BE EF

 

03

06 00

 

 

 

E3

C7

 

 

01 00

 

BA 30

 

40 00

 

 

Get

BE EF

 

03

06 00

 

 

 

10

F6

 

 

02 00

 

BA 30

 

00 00

 

 

 

[Example return] 

00

 

04

00

 

10

00

 

 

 

 

 

00

00

01

 

 

 

 

 

 

 

[Normal]

 

[Cinema]

[Dynamic]

[Custom]

 

40 00

 

 

 

 

 

20 00

21 00

 

 

22

00

 

 

 

 

 

 

[BOARD(BLACK) ]

[BOARD(GREEN)]

[WHITEBOARD]

 

[DAY TIME]

GAMMA

Set

#1 DEFAULT

BE EF

 

03

06 00

 

 

 

07 E9

 

 

01 00

 

A1

30

 

20 00

 

 

#1 CUSTOM

BE EF

 

03

06 00

 

 

 

07 FD

 

 

01 00

 

A1

30

 

10 00

 

 

#2 DEFAULT

BE EF

 

03

06 00

 

 

 

97 E8

 

 

01 00

 

A1

30

 

21 00

 

 

#2 CUSTOM

BE EF

 

03

06 00

 

 

 

97 FC

 

 

01 00

 

A1

30

 

11 00

 

 

#3 DEFAULT

BE EF

 

03

06 00

 

 

 

67 E8

 

 

01 00

 

A1

30

 

22 00

 

 

#3 CUSTOM

BE EF

 

03

06 00

 

 

 

67 FC

 

 

01 00

 

A1

30

 

12 00

 

 

#4 DEFAULT

BE EF

 

03

06 00

 

 

 

F7 E9

 

 

01 00

 

A1

30

 

23 00

 

 

#4 CUSTOM

BE EF

 

03

06 00

 

 

 

F7 FD

 

 

01 00

 

A1

30

 

13 00

 

 

#5 DEFAULT

BE EF

 

03

06 00

 

 

 

C7 EB

 

 

01 00

 

A1

30

 

24 00

 

 

#5 CUSTOM

BE EF

 

03

06 00

 

 

 

C7 FF

 

 

01 00

 

A1

30

 

14 00

 

 

#6 DEFAULT

BE EF

 

03

06 00

 

 

 

57 EA

 

 

01 00

 

A1

30

 

25 00

 

 

#6 CUSTOM

BE EF

 

03

06 00

 

 

 

57 FE

 

 

01 00

 

A1

30

 

15 00

 

 

Get

BE EF

 

03

06 00

 

 

 

F4 F0

 

 

02 00

 

A1

30

 

00 00

(continued on next page)

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

User Gamma Pattern

Set

Off

BE EF

03

06 00

FB FA

01 00

80 30

00 00

 

 

9 step gray scale

BE EF

03

06 00

6B

FB

01 00

80 30

01 00

 

 

15 steps gray scale

BE EF

03

06 00

9B

FB

01 00

80 30

02 00

 

 

Ramp

BE EF

03

06 00

0B FA

01 00

80 30

03 00

 

 

Get

BE EF

03

06 00

C8 FA

02 00

80 30

00 00

User Gamma Point 1

 

Get

BE EF

03

06 00

08 FE

02 00

90 30

00 00

 

 

Increment

BE EF

03

06 00

6E

FE

04 00

90 30

00 00

 

 

Decrement

BE EF

03

06 00

BF FF

05 00

90 30

00 00

User Gamma Point 2

 

Get

BE EF

03

06 00

F4

FF

02 00

91 30

00 00

 

 

Increment

BE EF

03

06 00

92

FF

04 00

91 30

00 00

 

 

Decrement

BE EF

03

06 00

43 FE

05 00

91 30

00 00

User Gamma Point 3

 

Get

BE EF

03

06 00

B0

FF

02 00

92 30

00 00

 

 

Increment

BE EF

03

06 00

D6 FF

04 00

92 30

00 00

 

 

Decrement

BE EF

03

06 00

07 FE

05 00

92 30

00 00

User Gamma Point 4

 

Get

BE EF

03

06 00

4C

FE

02 00

93 30

00 00

 

 

Increment

BE EF

03

06 00

2A

FE

04 00

93 30

00 00

 

 

Decrement

BE EF

03

06 00

FB FF

05 00

93 30

00 00

User Gamma Point 5

 

Get

BE EF

03

06 00

38

FF

02 00

94 30

00 00

 

 

Increment

BE EF

03

06 00

5E

FF

04 00

94 30

00 00

 

 

Decrement

BE EF

03

06 00

8F

FE

05 00

94 30

00 00

User Gamma Point 6

 

Get

BE EF

03

06 00

C4

FE

02 00

95 30

00 00

 

 

Increment

BE EF

03

06 00

A2

FE

04 00

95 30

00 00

 

 

Decrement

BE EF

03

06 00

73

FF

05 00

95 30

00 00

User Gamma Point 7

 

Get

BE EF

03

06 00

80 FE

02 00

96 30

00 00

 

 

Increment

BE EF

03

06 00

E6

FE

04 00

96 30

00 00

 

 

Decrement

BE EF

03

06 00

37

FF

05 00

96 30

00 00

User Gamma Point 8

 

Get

BE EF

03

06 00

7C FF

02 00

97 30

00 00

 

 

Increment

BE EF

03

06 00

1A FF

04 00

97 30

00 00

 

 

Decrement

BE EF

03

06 00

CB FE

05 00

97 30

00 00

COLOR TEMP

Set

HIGH

BE EF

03

06 00

0B F5

01 00

B0

30

03 00

 

 

CUSTOM-1(HIGH)

BE EF

03

06 00

CB F8

01 00

B0

30

13 00

 

 

MID

BE EF

03

06 00

9B F4

01 00

B0

30

02 00

 

 

CUSTOM-2(MID)

BE EF

03

06 00

5B F9

01 00

B0

30

12 00

 

 

LOW

BE EF

03

06 00

6B F4

01 00

B0

30

01 00

 

 

CUSTOM-3(LOW)

BE EF

03

06 00

AB F9

01 00

B0

30

11 00

 

 

Hi-BRIGHT-1

BE EF

03

06 00

3B F2

01 00

B0

30

08 00

 

 

CUSTOM-4(Hi-BRIGHT-1)

BE EF

03

06 00

FB FF

01 00

B0

30

18 00

 

 

Hi-BRIGHT-2

BE EF

03

06 00

AB F3

01 00

B0

30

09 00

 

 

CUSTOM-5(Hi-BRIGHT-2)

BE EF

03

06 00

6B

FE

01 00

B0

30

19 00

 

 

Hi-BRIGHT-3

BE EF

03

06 00

5B F3

01 00

B0

30

0A 00

 

 

CUSTOM-6(Hi-BRIGHT-3)

BE EF

03

06 00

9B

FE

01 00

B0

30

1A 00

 

 

Get

BE EF

03

06 00

C8 F5

02 00

B0

30

00 00

COLOR TEMP GAIN R

 

Get

BE EF

03

06 00

34

F4

02 00

B1

30

00 00

 

 

Increment

BE EF

03

06 00

52

F4

04 00

B1

30

00 00

 

 

Decrement

BE EF

03

06 00

83

F5

05 00

B1

30

00 00

COLOR TEMP GAIN G

 

Get

BE EF

03

06 00

70

F4

02 00

B2

30

00 00

 

 

Increment

BE EF

03

06 00

16

F4

04 00

B2

30

00 00

 

 

Decrement

BE EF

03

06 00

C7

F5

05 00

B2

30

00 00

10 (continued on next page)

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR TEMP GAIN B

 

Get

BE EF

03

06 00

8C F5

02 00

B3 30

00 00

 

 

Increment

BE EF

03

06 00

EA F5

04 00

B3 30

00 00

 

 

Decrement

BE EF

03

06 00

3B F4

05 00

B3 30

00 00

COLOR TEMP

 

Get

BE EF

03

06 00

04

F5

02 00

B5 30

00 00

OFFSET R

 

Increment

BE EF

03

06 00

62

F5

04 00

B5 30

00 00

 

 

Decrement

BE EF

03

06 00

B3 F4

05 00

B5 30

00 00

COLOR TEMP

 

Get

BE EF

03

06 00

40

F5

02 00

B6 30

00 00

OFFSET G

 

Increment

BE EF

03

06 00

26

F5

04 00

B6 30

00 00

 

 

Decrement

BE EF

03

06 00

F7

F4

05 00

B6 30

00 00

COLOR TEMP

 

Get

BE EF

03

06 00

BC F4

02 00

B7 30

00 00

OFFSET B

 

Increment

BE EF

03

06 00

DA F4

04 00

B7 30

00 00

 

 

Decrement

BE EF

03

06 00

0B F5

05 00

B7 30

00 00

COLOR

 

Get

BE EF

03

06 00

B5 72

02 00

02 22

00 00

 

 

Increment

BE EF

03

06 00

D3 72

04 00

02 22

00 00

 

 

Decrement

BE EF

03

06 00

02

73

05 00

02 22

00 00

COLOR Reset

 

Execute

BE EF

03

06 00

80 D0

06 00

0A 70

00 00

TINT

 

Get

BE EF

03

06 00

49

73

02 00

03 22

00 00

 

 

Increment

BE EF

03

06 00

2F 73

04 00

03 22

00 00

 

 

Decrement

BE EF

03

06 00

FE 72

05 00

03 22

00 00

TINT Reset

 

Execute

BE EF

03

06 00

7C

D1

06 00

0B 70

00 00

SHARPNESS

 

Get

BE EF

03

06 00

F1 72

02 00

01 22

00 00

 

 

Increment

BE EF

03

06 00

97

72

04 00

01 22

00 00

 

 

Decrement

BE EF

03

06 00

46

73

05 00

01 22

00 00

SHARPNESS Reset

 

Execute

BE EF

03

06 00

C4

D0

06 00

09 70

00 00

MY MEMORY Load

Set

1

BE EF

03

06 00

0E

D7

01 00

14 20

00 00

 

 

2

BE EF

03

06 00

9E

D6

01 00

14 20

01 00

 

 

3

BE EF

03

06 00

6E

D6

01 00

14 20

02 00

 

 

4

BE EF

03

06 00

FE

D7

01 00

14 20

03 00

MY MEMORY Save

Set

1

BE EF

03

06 00

F2 D6

01 00

15 20

00 00

 

 

2

BE EF

03

06 00

62 D7

01 00

15 20

01 00

 

 

3

BE EF

03

06 00

92 D7

01 00

15 20

02 00

 

 

4

BE EF

03

06 00

02 D6

01 00

15 20

03 00

PROGRESSIVE

Set

TURN OFF

BE EF

03

06 00

4A 72

01 00

07 22

00 00

 

 

TV

BE EF

03

06 00

DA 73

01 00

07 22

01 00

 

 

FILM

BE EF

03

06 00

2A 73

01 00

07 22

02 00

 

 

Get

BE EF

03

06 00

79

72

02 00

07 22

00 00

VIDEO NR

Set

LOW

BE EF

03

06 00

26

72

01 00

06 22

01 00

 

 

MID

BE EF

03

06 00

D6 72

01 00

06 22

02 00

 

 

HIGH

BE EF

03

06 00

46

73

01 00

06 22

03 00

 

 

Get

BE EF

03

06 00

85

73

02 00

06 22

00 00

ASPECT

Set

4:3

BE EF

03

06 00

9E

D0

01 00

08 20

00 00

 

 

16:9

BE EF

03

06 00

0E

D1

01 00

08 20

01 00

 

 

14:9

BE EF

03

06 00

CE D6

01 00

08 20

09 00

 

 

SMALL

BE EF

03

06 00

FE

D1

01 00

08 20

02 00

 

 

NORMAL

BE EF

03

06 00

5E DD

01 00

08 20

10 00

 

 

Get

BE EF

03

06 00

AD D0

02 00

08 20

00 00

(continued on next page)

11

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OVER SCAN

 

Get

BE EF

03

06 00

91 70

02 00

09 22

00 00

 

 

Increment

BE EF

03

06 00

F7

70

04 00

09 22

00 00

 

 

Decrement

BE EF

03

06 00

26 71

05 00

09 22

00 00

OVER SCAN Reset

 

Execute

BE EF

03

06 00

EC D9

06 00

27 70

00 00

V POSITION

 

Get

BE EF

03

06 00

0D 83

02 00

00 21

00 00

 

 

Increment

BE EF

03

06 00

6B 83

04 00

00 21

00 00

 

 

Decrement

BE EF

03

06 00

BA 82

05 00

00 21

00 00

V POSITION Reset

 

Execute

BE EF

03

06 00

E0 D2

06 00

02 70

00 00

H POSITION

 

Get

BE EF

03

06 00

F1

82

02 00

01 21

00 00

 

 

Increment

BE EF

03

06 00

97 82

04 00

01 21

00 00

 

 

Decrement

BE EF

03

06 00

46 83

05 00

01 21

00 00

H POSITION Reset

 

Execute

BE EF

03

06 00

1C

D3

06 00

03 70

00 00

H PHASE

 

Get

BE EF

03

06 00

49 83

02 00

03 21

00 00

 

 

Increment

BE EF

03

06 00

2F

83

04 00

03 21

00 00

 

 

Decrement

BE EF

03

06 00

FE 82

05 00

03 21

00 00

H SIZE

 

Get

BE EF

03

06 00

B5 82

02 00

02 21

00 00

 

 

Increment

BE EF

03

06 00

D3 82

04 00

02 21

00 00

 

 

Decrement

BE EF

03

06 00

02 83

05 00

02 21

00 00

H SIZE Reset

 

Execute

BE EF

03

06 00

68 D2

06 00

04 70

00 00

AUTO ADJUST

 

Execute

BE EF

03

06 00

91 D0

06 00

0A 20

00 00

COLOR SPACE

Set

AUTO

BE EF

03

06 00

0E 72

01 00

04 22

00 00

 

 

RGB

BE EF

03

06 00

9E 73

01 00

04 22

01 00

 

 

SMPTE240

BE EF

03

06 00

6E 73

01 00

04 22

02 00

 

 

REC709

BE EF

03

06 00

FE 72

01 00

04 22

03 00

 

 

REC601

BE EF

03

06 00

CE 70

01 00

04 22

04 00

 

 

Get

BE EF

03

06 00

3D 72

02 00

04 22

00 00

COMPONENT

Set

COMPONENT

BE EF

03

06 00

4A D7

01 00

17 20

00 00

 

 

SCART RGB

BE EF

03

06 00

DA D6

01 00

17 20

01 00

 

 

Get

BE EF

03

06 00

79 D7

02 00

17 20

00 00

C-VIDEOFORMAT

Set

AUTO

BE EF

03

06 00

A2 70

01 00

11 22

0A 00

 

 

NTSC

BE EF

03

06 00

C2 74

01 00

11 22

04 00

 

 

PAL

BE EF

03

06 00

52 75

01 00

11 22

05 00

 

 

SECAM

BE EF

03

06 00

52 70

01 00

11 22

09 00

 

 

NTSC4.43

BE EF

03

06 00

62 77

01 00

11 22

02 00

 

 

M-PAL

BE EF

03

06 00

C2 71

01 00

11 22

08 00

 

 

N-PAL

BE EF

03

06 00

32 74

01 00

11 22

07 00

 

 

Get

BE EF

03

06 00

31 76

02 00

11 22

00 00

S-VIDEOFORMAT

Set

AUTO

BE EF

03

06 00

E6 70

01 00

12 22

0A 00

 

 

NTSC

BE EF

03

06 00

86 74

01 00

12 22

04 00

 

 

PAL

BE EF

03

06 00

16 75

01 00

12 22

05 00

 

 

SECAM

BE EF

03

06 00

16 70

01 00

12 22

09 00

 

 

NTSC4.43

BE EF

03

06 00

26 77

01 00

12 22

02 00

 

 

M-PAL

BE EF

03

06 00

86 71

01 00

12 22

08 00

 

 

N-PAL

BE EF

03

06 00

76 74

01 00

12 22

07 00

 

 

Get

BE EF

03

06 00

75 76

02 00

12 22

00 00

FRAME LOCK

Set

TURN OFF

BE EF

03

06 00

CB D6

01 00

14 30

00 00

 

 

TURN ON

BE EF

03

06 00

5B D7

01 00

14 30

01 00

 

 

Get

BE EF

03

06 00

F8 D6

02 00

14 30

00 00

12

(continued on next page)

 

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER IN1

Set

SYNC ON G ON

BE EF

03

06 00

CE D6

01 00

10 20

03 00

 

 

SYNC ON G OFF

BE EF

03

06 00

5E D7

01 00

10 20

02 00

 

 

Get

BE EF

03

06 00

0D D6

02 00

10 20

00 00

COMPUTER IN2

Set

SYNC ON G ON

BE EF

03

06 00

32

D7

01 00

11 20

03 00

 

 

SYNC ON G OFF

BE EF

03

06 00

A2 D6

01 00

11 20

02 00

 

 

Get

BE EF

03

06 00

F1

D7

02 00

11 20

00 00

KEYSTONE V

 

Get

BE EF

03

06 00

B9 D3

02 00

07 20

00 00

 

 

Increment

BE EF

03

06 00

DF D3

04 00

07 20

00 00

 

 

Decrement

BE EF

03

06 00

0E D2

05 00

07 20

00 00

KEYSTONE V Reset

 

Execute

BE EF

03

06 00

08

D0

06 00

0C 70

00 00

AUTO KEYSTONE

 

Execute

BE EF

03

06 00

E5 D1

06 00

0D 20

00 00

EXECUTE

 

 

 

 

 

 

 

 

 

 

WHISPER

Set

NORMAL

BE EF

03

06 00

3B 23

01 00

00 33

00 00

 

 

WHISPER

BE EF

03

06 00

AB 22

01 00

00 33

01 00

 

 

Get

BE EF

03

06 00

08 23

02 00

00 33

00 00

MIRROR

Set

NORMAL

BE EF

03

06 00

C7 D2

01 00

01 30

00 00

 

 

H:INVERT

BE EF

03

06 00

57

D3

01 00

01 30

01 00

 

 

V:INVERT

BE EF

03

06 00

A7 D3

01 00

01 30

02 00

 

 

H&V:INVERT

BE EF

03

06 00

37

D2

01 00

01 30

03 00

 

 

Get

BE EF

03

06 00

F4

D2

02 00

01 30

00 00

VOLUME-

 

Get

BE EF

03

06 00

CD CC

02 00

60 20

00 00

COMPUTER1

 

Increment

BE EF

03

06 00

AB CC

04 00

60 20

00 00

 

 

Decrement

BE EF

03

06 00

7A

CD

05 00

60 20

00 00

VOLUME-

 

Get

BE EF

03

06 00

FD CD

02 00

64 20

00 00

COMPUTER2

 

Increment

BE EF

03

06 00

9B

CD

04 00

64 20

00 00

 

 

Decrement

BE EF

03

06 00

4A

CC

05 00

64 20

00 00

VOLUME-

 

Get

BE EF

03

06 00

01 CC

02 00

65 20

00 00

COMPONENT

 

Increment

BE EF

03

06 00

67 CC

04 00

65 20

00 00

 

 

Decrement

BE EF

03

06 00

B6

CD

05 00

65 20

00 00

VOLUME-S-Video

 

Get

BE EF

03

06 00

75 CD

02 00

62 20

00 00

 

 

Increment

BE EF

03

06 00

13 CD

04 00

62 20

00 00

 

 

Decrement

BE EF

03

06 00

C2

CC

05 00

62 20

00 00

VOLUME-Video

 

Get

BE EF

03

06 00

31 CD

02 00

61 20

00 00

 

 

Increment

BE EF

03

06 00

57 CD

04 00

61 20

00 00

 

 

Decrement

BE EF

03

06 00

86 CC

05 00

61 20

00 00

MUTE

Set

TURN OFF

BE EF

03

06 00

46

D3

01 00

02 20

00 00

 

 

TURN ON

BE EF

03

06 00

D6 D2

01 00

02 20

01 00

 

 

Get

BE EF

03

06 00

75

D3

02 00

02 20

00 00

SPEAKER

Set

TURN ON

BE EF

03

06 00

FE D4

01 00

1C 20

01 00

 

 

TURN OFF

BE EF

03

06 00

6E D5

01 00

1C 20

00 00

 

 

Get

BE EF

03

06 00

5D D5

02 00

1C 20

00 00

(continued on next page)

13

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO-COMPUTER1

Set

AUDIO1

BE EF

03

06 00

6E

DC

01 00

30 20

01 00

 

 

AUDIO2

BE EF

03

06 00

9E

DC

01 00

30 20

02 00

 

 

AUDIO3

BE EF

03

06 00

0E

DD

01 00

30 20

03 00

 

 

Turn off

BE EF

03

06 00

FE DD

01 00

30 20

00 00

 

 

Get

BE EF

03

06 00

CD DD

02 00

30 20

00 00

AUDIO-COMPUTER2

Set

AUDIO1

BE EF

03

06 00

5E

DD

01 00

34 20

01 00

 

 

AUDIO2

BE EF

03

06 00

AE DD

01 00

34 20

02 00

 

 

AUDIO3

BE EF

03

06 00

3E

DC

01 00

34 20

03 00

 

 

Turn off

BE EF

03

06 00

CE DC

01 00

34 20

00 00

 

 

Get

BE EF

03

06 00

FD DC

02 00

34 20

00 00

AUDIO-COMPONENT

Set

AUDIO1

BE EF

03

06 00

A2

DC

01 00

35 20

01 00

 

 

AUDIO2

BE EF

03

06 00

52

DC

01 00

35 20

02 00

 

 

AUDIO3

BE EF

03

06 00

C2

DD

01 00

35 20

03 00

 

 

Turn off

BE EF

03

06 00

32

DD

01 00

35 20

00 00

 

 

Get

BE EF

03

06 00

01

DD

02 00

35 20

00 00

AUDIO-S-VIDEO

Set

AUDIO1

BE EF

03

06 00

D6

DD

01 00

32 20

01 00

 

 

AUDIO2

BE EF

03

06 00

26

DD

01 00

32 20

02 00

 

 

AUDIO3

BE EF

03

06 00

B6

DC

01 00

32 20

03 00

 

 

Turn off

BE EF

03

06 00

46

DC

01 00

32 20

00 00

 

 

Get

BE EF

03

06 00

75

DC

02 00

32 20

00 00

AUDIO-VIDEO

Set

AUDIO1

BE EF

03

06 00

92

DD

01 00

31 20

01 00

 

 

AUDIO2

BE EF

03

06 00

62

DD

01 00

31 20

02 00

 

 

AUDIO3

BE EF

03

06 00

F2

DC

01 00

31 20

03 00

 

 

Turn off

BE EF

03

06 00

02

DC

01 00

31 20

00 00

 

 

Get

BE EF

03

06 00

31

DC

02 00

31 20

00 00

IR REMOTE FREQ.

Set

Off

BE EF

03

06 00

FF 3D

01 00

30 26

00 00

NORMAL

 

On

BE EF

03

06 00

6F 3C

01 00

30 26

01 00

 

 

Get

BE EF

03

06 00

CC 3D

02 00

30 26

00 00

IR REMOTE FREQ.

Set

Off

BE EF

03

06 00

03

3C

01 00

31 26

00 00

HIGH

 

On

BE EF

03

06 00

93

3D

01 00

31 26

01 00

 

 

Get

BE EF

03

06 00

30

3C

02 00

31 26

00 00

(continued on next page)

14

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

LANGUAGE

Set

ENGLISH

BE EF

03

06 00

F7

D3

01 00

05 30

00 00

 

 

FRANÇAIS

BE EF

03

06 00

67

D2

01 00

05 30

01 00

 

 

DEUTSCH

BE EF

03

06 00

97

D2

01 00

05 30

02 00

 

 

ESPAÑOL

BE EF

03

06 00

07

D3

01 00

05 30

03 00

 

 

ITALIANO

BE EF

03

06 00

37

D1

01 00

05 30

04 00

 

 

NORSK

BE EF

03

06 00

A7

D0

01 00

05 30

05 00

 

 

NEDERLANDS

BE EF

03

06 00

57

D0

01 00

05 30

06 00

 

 

PORTUGUÊS

BE EF

03

06 00

C7 D1

01 00

05 30

07 00

 

 

 

BE EF

03

06 00

37

D4

01 00

05 30

08 00

 

 

 

BE EF

03

06 00

A7

D5

01 00

05 30

09 00

 

 

 

BE EF

03

06 00

37 DE

01 00

05 30

10 00

 

 

 

BE EF

03

06 00

57

D5

01 00

05 30

0A 00

 

 

SVENSKA

BE EF

03

06 00

C7 D4

01 00

05 30

0B 00

 

 

PУCCKИЙ

BE EF

03

06 00

F7

D6

01 00

05 30

0C 00

 

 

SUOMI

BE EF

03

06 00

67

D7

01 00

05 30

0D 00

 

 

POLSKI

BE EF

03

06 00

97

D7

01 00

05 30

0E 00

 

 

TÜRKÇE

BE EF

03

06 00

07

D6

01 00

05 30

0F 00

 

 

Get

BE EF

03

06 00

C4 D3

02 00

05 30

00 00

MENU POSITION H

 

Get

BE EF

03

06 00

04

D7

02 00

15 30

00 00

 

 

Increment

BE EF

03

06 00

62

D7

04 00

15 30

00 00

 

 

Decrement

BE EF

03

06 00

B3

D6

05 00

15 30

00 00

MENU POSITION H Reset

 

Execute

BE EF

03

06 00

DC C6

06 00

43 70

00 00

MENU POSITION V

 

Get

BE EF

03

06 00

40

D7

02 00

16 30

00 00

 

 

Increment

BE EF

03

06 00

26

D7

04 00

16 30

00 00

 

 

Decrement

BE EF

03

06 00

F7

D6

05 00

16 30

00 00

MENU POSITION V Reset

 

Execute

BE EF

03

06 00

A8

C7

06 00

44 70

00 00

BLANK

Set

MyScreen

BE EF

03

06 00

FB

CA

01 00

00 30

20 00

 

 

ORIGINAL

BE EF

03

06 00

FB E2

01 00

00 30

40 00

 

 

BLUE

BE EF

03

06 00

CB D3

01 00

00 30

03 00

 

 

WHITE

BE EF

03

06 00

6B

D0

01 00

00 30

05 00

 

 

BLACK

BE EF

03

06 00

9B

D0

01 00

00 30

06 00

 

 

Get

BE EF

03

06 00

08

D3

02 00

00 30

00 00

BLANK On/Off

Set

TURN OFF

BE EF

03

06 00

FB D8

01 00

20 30

00 00

 

 

TURN ON

BE EF

03

06 00

6B

D9

01 00

20 30

01 00

 

 

Get

BE EF

03

06 00

C8 D8

02 00

20 30

00 00

START UP

Set

MyScreen

BE EF

03

06 00

CB CB

01 00

04 30

20 00

 

 

ORIGINAL

BE EF

03

06 00

0B D2

01 00

04 30

00 00

 

 

TURN OFF

BE EF

03

06 00

9B D3

01 00

04 30

01 00

 

 

Get

BE EF

03

06 00

38

D2

02 00

04 30

00 00

MyScreen LOCK

Set

TURN OFF

BE EF

03

06 00

3B EF

01 00

C0 30

00 00

 

 

TURN ON

BE EF

03

06 00

AB EE

01 00

C0 30

01 00

 

 

Get

BE EF

03

06 00

08

EF

02 00

C0 30

00 00

MESSAGE

Set

TURN OFF

BE EF

03

06 00

8F

D6

01 00

17 30

00 00

 

 

TURN ON

BE EF

03

06 00

1F

D7

01 00

17 30

01 00

 

 

Get

BE EF

03

06 00

BC D6

02 00

17 30

00 00

AUTO SEARCH

Set

TURN OFF

BE EF

03

06 00

B6 D6

01 00

16 20

00 00

 

 

TURN ON

BE EF

03

06 00

26

D7

01 00

16 20

01 00

 

 

Get

BE EF

03

06 00

85

D6

02 00

16 20

00 00

(continued on next page)

15

 

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO KEYSTONE

Set

TURN OFF

BE EF

03

06 00

EA D1

01 00

0F 20

00 00

 

 

TURN ON

BE EF

03

06 00

7A

D0

01 00

0F 20

01 00

 

 

Get

BE EF

03

06 00

D9

D1

02 00

0F 20

00 00

AUTO ON

Set

TURN OFF

BE EF

03

06 00

3B 89

01 00

20 31

00 00

 

 

TURN ON

BE EF

03

06 00

AB 88

01 00

20 31

01 00

 

 

Get

BE EF

03

06 00

08 89

02 00

20 31

00 00

AUTO OFF

 

Get

BE EF

03

06 00

08

86

02 00

10 31

00 00

 

 

Increment

BE EF

03

06 00

6E 86

04 00

10 31

00 00

 

 

Decrement

BE EF

03

06 00

BF 87

05 00

10 31

00 00

LAMP TIME

 

Get

BE EF

03

06 00

C2

FF

02 00

90 10

00 00

LAMP TIME Reset

 

Execute

BE EF

03

06 00

58 DC

06 00

30 70

00 00

FILTER TIME

 

Get

BE EF

03

06 00

C2 F0

02 00

A0 10

00 00

FILER TIME Reset

 

Execute

BE EF

03

06 00

98 C6

06 00

40 70

00 00

MY BUTTON-1

 

COMPUTER1

BE EF

03

06 00

3A 33

01 00

00 36

00 00

 

 

COMPUTER2

BE EF

03

06 00

FA 31

01 00

00 36

04 00

 

 

COMPONENT

BE EF

03

06 00

6A 30

01 00

00 36

05 00

 

 

S-VIDEO

BE EF

03

06 00

5A 32

01 00

00 36

02 00

 

 

VIDEO

BE EF

03

06 00

AA 32

01 00

00 36

01 00

 

 

INFORMATION

BE EF

03

06 00

FA 3E

01 00

00 36

10 00

 

AUTO KEYSTONE EXECUTE

BE EF

03

06 00

6A 3F

01 00

00 36

11 00

 

 

MY MEMORY

BE EF

03

06 00

9A 3F

01 00

00 36

12 00

 

 

PICTURE MODE

BE EF

03

06 00

0A

3E

01 00

00 36

13 00

 

 

FILTER RESET

BE EF

03

06 00

3A

3C

01 00

00 36

14 00

 

 

e-SHOT

BE EF

03

06 00

5A

3D

01 00

00 36

16 00

 

 

VOLUME +

BE EF

03

06 00

CA 3C

01 00

00 36

17 00

 

 

VOLUME -

BE EF

03

06 00

3A 39

01 00

00 36

18 00

 

 

Get

BE EF

03

06 00

09

33

02 00

00 36

00 00

MY BUTTON-2

 

COMPUTER1

BE EF

03

06 00

C6 32

01 00

01 36

00 00

 

 

COMPUTER2

BE EF

03

06 00

06

30

01 00

01 36

04 00

 

 

COMPONENT

BE EF

03

06 00

96

31

01 00

01 36

05 00

 

 

S-VIDEO

BE EF

03

06 00

A6 33

01 00

01 36

02 00

 

 

VIDEO

BE EF

03

06 00

56

33

01 00

01 36

01 00

 

 

INFORMATION

BE EF

03

06 00

06

3F

01 00

01 36

10 00

 

AUTO KEYSTONE EXECUTE

BE EF

03

06 00

96 3E

01 00

01 36

11 00

 

 

MY MEMORY

BE EF

03

06 00

66 3E

01 00

01 36

12 00

 

 

PICTURE MODE

BE EF

03

06 00

F6

3F

01 00

01 36

13 00

 

 

FILTER RESET

BE EF

03

06 00

C6

3D

01 00

01 36

14 00

 

 

e-SHOT

BE EF

03

06 00

A6

3C

01 00

01 36

16 00

 

 

VOLUME +

BE EF

03

06 00

36 3D

01 00

01 36

17 00

 

 

VOLUME -

BE EF

03

06 00

C6 38

01 00

01 36

18 00

 

 

Get

BE EF

03

06 00

F5

32

02 00

01 36

00 00

MAGNIFY

 

Get

BE EF

03

06 00

7C

D2

02 00

07 30

00 00

 

 

Increment

BE EF

03

06 00

1A

D2

04 00

07 30

00 00

 

 

Decrement

BE EF

03

06 00

CB D3

05 00

07 30

00 00

FREEZE

Set

NORMAL

BE EF

03

06 00

83 D2

01 00

02 30

00 00

 

 

FREEZE

BE EF

03

06 00

13 D3

01 00

02 30

01 00

 

 

Get

BE EF

03

06 00

B0

D2

02 00

02 30

00 00

16

RS-232CCommunication (continued)

RS-232Ccommunication command table (continued)

Names 

 

Operation Type

 

Header

 

 

 

 

Command Data

 

 

 

CRC

Action

Type

Setting Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

e-SHOT

Set

OFF

BE EF

03

06 00

3A

C3

01 00

00 35

00 00

 

 

IMAGE1

BE EF

03

06 00

AA C2

01 00

00 35

01 00

 

 

IMAGE2

BE EF

03

06 00

5A

C2

01 00

00 35

02 00

 

 

IMAGE3

BE EF

03

06 00

CA C3

01 00

00 35

03 00

 

 

IMAGE4

BE EF

03

06 00

FA C1

01 00

00 35

04 00

 

 

Get

BE EF

03

06 00

09

C3

02 00

00 35

00 00

e-SHOTIMAGE1 Delete

 

Execute

BE EF

03

06 00

71

C3

06 00

01 35

00 00

e-SHOTIMAGE2 Delete

 

Execute

BE EF

03

06 00

35

C3

06 00

02 35

00 00

e-SHOTIMAGE3 Delete

 

Execute

BE EF

03

06 00

C9

C2

06 00

03 35

00 00

e-SHOTIMAGE4 Delete

 

Execute

BE EF

03

06 00

BD C3

06 00

04 35

00 00

17

Read this Safety Guide first.

Projector

User's Manual - Safety Guide

Thank you for purchasing this projector.

WARNING • Before using, read this manual to ensure correct usage.

After reading, store it in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage. The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage defined in this manual.

NOTE • The information in this manual is subject to change without notice.

The manufacturer assumes no responsibility for any errors that may appear in this manual.

The reproduction, transmission or use of this document or contents is not permitted without express written authority.

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents.

This symbol indicates information that, if ignored, could WARNING possibly result in personal injury or even death due to

incorrect handling.

This symbol indicates information that, if ignored, could CAUTION result possibly in personal injury or physical damage

due to incorrect handling.

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that the power plug should be disconnected from the power outlet).

1

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.

In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision problem.

Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present.

If liquids or foreign object should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the projector near water (ex. a bathroom, a beach, etc.).

Do not expose the projector to rain or moisture. Do not place the projector outdoors.

Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the projector.

Do not place metals, combustibles, etc on or around the projector.

To avoid penetration of foreign objects, do not put the projector into a case or bag together with any thing except the accessories of the projector, signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of the projector or accessories could result in fire or electrical shock.

Never open the cabinet.

Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

If the projector is shocked, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

Do not place the projector on an unstable, slant or vibrant surface such as a wobbly or inclined stand.

Use the caster brakes placing the projector on a stand with casters.

Do not place the projector in the side up position, the lens up position or the lens down position.

In the case of a ceiling installation or the like, contact your dealer before installation.

Disconnect the plug from the power outlet.

Do not disassemble.

Safety Precautions (continued)

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present.

Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such as walls.

Do not place the projector on a metallic table or anything weak in heat.

Do not place anything about the lens, air fans and ventilation openings of the projector.

Never block the air fan and ventilation openings.

Do not cover the projector with a tablecloth, etc.

Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision.

Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

Use only the correct power outlet depending on the indication on the projector and the safety standard.

The enclosed power cord must be used depending on the power outlet to be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

Do not touch the power cord with a wet hand.

Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.

Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using the correct power cord; otherwise, fire or electric shock can result.

• Don’t take the core of power cord away.

Surely connect the ground wire.

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressuremercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection cables.

If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

Do not place the projector or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

Do not place the cord near the heater.

Avoid bending the power cord sharply.

Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not allow the battery in a fire or water.

Avoid fire or high-temperatureenvironment.

Do not hold the battery with the metallic tweezers.

Keep the battery in a dark, cool and dry play.

Do not short circuit the battery.

Do not recharge, disassemble or solder the battery.

Do not give the battery a physical impact.

Use only the battery specified in the other manual of this projector.

Make sure the plus and minus terminals are correctly aligned when loading the battery.

If you observe a leakage of the battery, wipe out the flower and then replace the battery. If the flower adheres your body or clothes, rinse well with water.

Obey the local laws on disposing the battery.

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.

Avoid any impact or shock to the projector.

Do not drag the projector.

For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling, and cause an injury or damage. Use special caution in households where children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.

Do not place the projector near a smoky, humid or dusty place (ex. a smoking space, a kitchen, a beach, etc.). Do not place the projector outdoors.

Do not use a humidifier near the projector.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction. The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged, replace the air filter.

Use the air filter of the specified type only. Please order the air filter specified in the other manual of this projector to your dealer.

When you replace the lamp, replace also the air filter. The air filter may be attached when you buy a replacement lamp for this projector.

Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and other parts. Do not place the projector, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.

Avoid Magnetism.

Manufacture strongly recommends to avoid any magnetic contact that is not shielded or protected on or near the projector itself. (ie.,. Magnetic Security Devices, or other projector accessory that contains magnetic material that has not been provided by the manufacture etc.) Magnetic objects may cause interruption of the projector's internal mechanical performance which may interfere with cooling

fans speed or stopping, and may cause the projector to completely shut down.

Safety Precautions (continued)

CAUTION

Remove the power cord for complete separation.

For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time.

Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Ask your dealer to cleaning inside of the projector about every year.

Accumulations of dust inside the projector cause result in fire or malfunction. Cleaning inside is more effective if performed before every humid periods such as rainy season.

• Do not clean inside yourself because it is dangerous.

Disconnect the plug from the power outlet.

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

Take care not to drop the remote control.

Do not place the projector or heavy objects on the remote control.

Take care of the lens.

Close the slide lens door or attach the lens cap to prevent the lens surface being scratched when the projector is not used.

Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display quality.

Use commercially available lens tissue to clean the lens (used to clean cameras, eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

Use a soft cloth to clean the cabinet and control panel of the projector and the remote control. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

Before using chemical wipes, be sure to read and observe the instructions.

Do not allow long-termclose contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

Safety Precautions (continued)

NOTE

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time.

This product isn’t designed for continuous use of long time. In the case of continuous use for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or repetitious use, the lifetime may be shortened, and these parts may need to be replaced even if one year has not passed since the beginning of using.

Any inclining use beyond the adjustment range explained in these user’s manuals may shorten the lifetimes of the consumables.

Before turning on the power, make the projector cool down adequately.

After turning the projector off, pushing the restart switch or interrupting of the power supply, make the projector cool down adequately. Operation in a high temperature state of the

projector causes a damage of the electrode and un-lightingof the lamp.

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on characteristic of the screen, because the projector uses a liquid crystal display panel. The display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless specifying.

Power on the projector before the computer or video tape recorder.

Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output (setting CRT display or simultaneous display of LCD and CRT).

Please read instruction manual of the notebook for more information.

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressuremercury glass lamp. The lamp canbreak with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible forshards of glass to fly into the lamp housing, and forgas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

 

• If the lamp should break (it will make a loud bang when it does), unplug

 

the power cord from the outlet, and make sure to request a replacement

 

lamp from your local dealer. Note that shards of glass could damage the

 

projector’s internals, or cause injury during handling, so please do not try to

 

clean the projector or replace the lamp yourself.

 

• If the lamp should break (it will make a loud bang when it does), ventilate

Disconnect

the room well, and make sure not to breathe the gas that comes out of the

the plug from

projector vents, or get it in your eyes or mouth.

the power

outlet

• Before replacing the lamp, make sure the power switch is off and the

 

power cable is not plugged in, then wait at least 45 minutes for the lamp to

 

cool sufficiently. Handling the lamp while hot can cause burns, as well as

 

damaging the lamp.

 

 

 

• Do not open the lamp cover while the projector is suspended from above.

 

This is dangerous, since if the lamp’s bulb has broken, the shards will

 

fall out when the cover is opened. In addition, working in high places is

 

dangerous, so ask your local dealer to have the lamp replaced even if the

 

bulb is not broken.

 

• Do not use the projector with the lamp cover removed. At the lamp

 

replacing, make sure that the screws are screwed in firmly. Loose screws

 

could result in damage or injury.

 

 

 

• Use the lamp of the specified type only.

 

• If the lamp breaks soon after the first time it is used, it is possible that

 

there are electrical problems elsewhere besides the lamp. If this happens,

 

contact your local dealer or a service representative.

 

• Handle with care: jolting or scratching could cause the lamp bulb to burst

 

during use.

 

• Using the lamp for long periods of time, could cause it dark, not to light up

 

or to burst. When the pictures appear dark, or when the color tone is poor,

 

please replace the lamp as soon as possible. Do not use old (used) lamps;

 

this is a cause of breakage.

Regulatory Notices

FCC Statement Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or adesignated-typecable for the connection. For cables that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with CanadianICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of WARNING in this manual), when a problem occurs with the equipment, first refer to the

“Troubleshooting” section of the “Operating Guide”, and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.

Audio Visual Products

2900 Dukane Drive

Toll-free:800-676-2487

St. Charles, Illinois 60174

Fax: 630-584-5156

www.dukcorp.com/av

e-mail:avsales@dukcorp.com

#401-8755E-01