Dukane 8791HW User Manual

Size:
7.27 Mb
Download

LCD Data Video Projector

User’s Manual

Model 8791HW

Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please visit the Dukane web site at; www.dukane.com/av and look at the specific model SUPPORT orDOWNLOADS section.

DUKANE CORP AV SERVICE DEPT

 

2900 Dukane Drive

 

St Charles, IL 60174

 

800-676-2487 /630-762-4032

 

Fax 630-584-5156

 

avservice@dukane.com

403-8791HW-GENERAL-00

www.dukane.com/av

Projector

8791HW

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” first. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

NOTICE This entry notices of fear of causing trouble.

Please refer to the pages written following this symbol.

NOTE • The information in this manual is subject to change without notice.

The manufacturer assumes no responsibility for any errors that may appear in this manual.

The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

Mac® is a registered trademark of Apple Inc.

Microsoft®, Internet Explorer®, Windows® and Windows Vista® are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

VESA and DDC are trademarks of the Video Electronics Standard Association.

HDMI, the HDMI logo and High-DefinitionMultimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Blu-rayDiscTM andBlu-rayTM are trademarks ofBlu-rayDisc Association.

All other trademarks are the properties of their respective owners.

1

 

Contents

Contents

 

 

 

 

Introduction . . . . . . . . . . . . . . . . 3

PICTURE menu. . . . . . . . . . . . . 27

Features. . . . . . . . . . . . 3

Brightness, Contrast, Gamma,

 

 

Checking the contents of package. .

3

Color temp, Color, Tint, Sharpness,

 

Part names. . . . . . . . . . . . . . . . . 4

My memory

 

 

Projector. . . . . . . . . . . . 4

IMAGE menu. . . . . . . . . . . . . . . 30

Control panel. . . . . . . . .

.

5

Aspect, Over scan, V position, H position,

Rear panel . . . . . . . . . . . 5

H phase, H size, Auto adjust execute

 

Remote control. . . . . . . .

.

6

INPUT menu . . . . . . . . . . . . . . . 33

Setting up. . . . . . . . . . . . . . . . . . 7

Progressive, Video nr, Color space,

 

Arrangement. . . . . . . . . . 7

Video format, Hdmi format, Hdmi range,

Connecting your devices. . . . .

 

. 9

Computer in, Frame lock, Resolution

 

Connecting power supply. . . .

. 11

SETUP menu. . . . . . . . .

. .37. . . .

Using the security bar and slot. .

. 11

Auto keystone, Keystone, Auto eco mode

Remote control. . . . . . . . . .12.

. E. co mode, Mirror, Standby mode,

 

 

Installing the batteries. . . . . .

 

12

Monitor out

 

 

About the remote control signal. .

 

12

AUDIO menu. . . . . . . . . . . . . . . 39

Power on/off . . . . . . . . . . . . . . . 13

Volume, Speaker, Audio source,

 

 

Turning on the power. . . . . .

 

13

Hdmi audio

 

 

Turning off the power. . . . . .

 

13

SCREEN menu. . . . . . . .

.

.40. . . .

Operating . . . . . . . . . . . . . . . . . 15

Language, Menu position, Blank,

 

 

Adjusting the volume. . . . . .

. 15

Start up, MyScreen, MyScreen Lock,

 

 

Temporarily muting the sound. . .

 

15

Message, Source name, Template, C.c.

Selecting an input signal. . . . .

 

15

OPTION menu. . . . . . . . . . . . . . 46

Searching an input signal. . . .

. 17

Auto search, Auto keystone,

 

 

Selecting an aspect ratio. . . . .

 

17

Direct power on, Auto power off,

 

 

Adjusting the projector's elevator.

. 18

Lamp time, Filter time, My button,

 

 

Adjusting the zoom and focus. . .

 

18

My source, Service

 

 

Using the automatic adjustment feature. .

 

19

SECURITY menu. . . . . . .

. .51. . .

Adjusting the position. . . . . .

 

19

Security password change,

 

 

Correcting the keystone distortions

. 20

 

 

MyScreen password, Pin lock,

 

 

Using the magnify feature. . . .

. 21

Transition detector, My text password,

Temporarily freezing the screen. . 22

My text display, My text writing

 

 

Temporarily blanking the screen . . 22

 

 

Maintenance. . . . . . . . . . .57. . . .

Using the menu function . . . .

. 23

Replacing the lamp. . . . . .

.

57

EASY MENU.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 25

Cleaning and replacing the air filter. .59

Aspect, Auto keystone, Keystone,

 

 

Other care. . . . . . . . . .

 

. 61

Picture mode, Eco mode, Mirror, Reset,

Troubleshooting . . . . . . . . . . . . 62

Filter time, Language, Advanced menu,

 

 

Related messages. . . . . .

.

62

Exit

 

 

 

 

Regarding the indicator lamps. . . 63

 

 

 

 

 

 

Resetting all settings. . . . . .

 

. 64

 

 

 

Phenomena that may be easy

 

 

 

 

 

to be mistaken for machine defects

 

. 65

 

 

 

Specifications. . . . . . . .

.

.69. . . .

2

Introduction

Introduction

Features

The projector provides you with the broad use by the following features.

üThis projector has a variety of I/O ports that supposedly cover for any business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen.

üThis projector realizes the large projection image, even if in a small space.

üThe new double layer filter system is expected to function longer and offers you less maintenance frequency.

üThis compact, lightweight projector uses a front exhaust system that keeps the user comfortable by directing hot air away from the user.

Checking the contents of package

Please see the Contents of packagesection in the User’s Manual (concise)which is a book. Require of your dealer immediately if any items are missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens.

3

Part names

Part names

Projector

(1)Lamp cover (&57)

The lamp unit is inside.

(2)Focus ring (&18)

(3)Zoom ring (&18)

(4)Control panel (&5)

(5)Elevator buttons (x 2) (&18)

(6)Elevator feet (x 2) (&18)

(7)Remote sensor (&12)

(8)Lens (&61)

(9)Intake vents

(10)Filter cover (&59)

The air filter and intake vent are inside.

(11)Speaker (&39)

(12)Exhaust vent

(13)AC IN (AC inlet) (&11)

(14)Rear panel (&5)

(15)Security bar (&11)

(16)Security slot (&11)

HOT!

(1) (2) (3)

 

(4)

 

 

 

(11)

 

 

 

(9)

 

 

 

(15)

(6)

 

 

(10)

 

 

(5)

 

 

 

HOT! (12)

(8)

(7)

(6)

 

 

 

 

 

 

(5)

 

 

 

(9)

(13)

(16)

 

 

 

(14)

 

WARNING HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes.

►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION ►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air filter periodically.

4

Control panel

(1)STANDBY/ON button (&13)

(2)INPUT button (&15, 23)

(3)MENU button (&23)

It consists of four cursor buttons.

(4)BLANK button (&22)

(5)POWER indicator (&11, 13, 63)

(6)TEMP indicator (&63)

(7)LAMP indicator (&63)

Part names

%/$1.

0< %87721

(4)

(6)(7) (5)

(1) (2) (3)

Rear panel (&9)

(1)

VIDEO port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(6)

COMPUTER IN port

 

(2)

S-VIDEOport

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(7)

HDMI port

 

(3)

AUDIO IN1 port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(8)

CONTROL port

 

(4)

AUDIO IN2 port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(9)

MONITOR OUT port

 

(5)

AUDIO OUT port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(2)

 

 

(3)

 

 

 

(6)

 

 

 

 

 

(7)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1)

(5)

(9)

(4)

(8)

5

Part names

Remote control

(1)VIDEO button (&16)

(2)COMPUTER button (&16)

(3)SEARCH button (&17)

(4)STANDBY/ON button (&13)

(5)ASPECT button (&17)

(6)AUTO button (&19)

(7)BLANK button (&22)

(8)MAGNIFY - ON button (&21)

(9)MAGNIFY - OFF button (&21)

(10)MY SOURCE/DOC.CAMERA button (&16, 48)

(11)VOLUME - button (&15)

(12)PAGE UP button *

(13)PAGE DOWN button *

(14)VOLUME + button (&15)

(15)MUTE button (&15)

(16)FREEZE button (&22)

(17)MY BUTTON - 1 button (&48)

(18)MY BUTTON - 2 button (&48)

(19)KEYSTONE button (&20)

(20)POSITION button (&19, 24)

(21)MENU button (&23)

(22)▲/▼/◄/► cursor buttons (&23)

(23)ENTER button (&23)

(24)ESC button (&23)

(25)RESET button (&23)

(26)Battery cover (&12)

(2)

 

 

 

 

(10)

(1)

 

 

 

 

(4)

(6)

VIDEO

 

MY SOURCE/

 

(3)

(5)

COMPUTER DOC.CAMERA

 

(7)

ASPECT

AUTO

SEARCH

BLANK

(16)

MAGNIFY

FREEZE

UP

VOLUME

(12)

(8)

 

 

PAGE

(14)

ON

 

DOWN

 

(9)

OFF

 

 

 

(11)

(19)

KEYSTONE

MY BUTTON

MUTE

(13)

 

 

1

2

 

 

(17)

 

 

 

 

(15)

(20)

POSITION

 

 

MENU

(18)

(22)

 

ENTER

 

(21)

 

ESC

 

 

RESET

(23)

(24)

 

 

 

 

(25)

(26)

Back of

the remote control

NOTE • Any button marked with “*” is not supported on this projector (&62).

6

Setting up

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1280 x 800

a Screen size (diagonal)

b Projection distance (±10%, from the projector's end)

c1 , c2 Screen height (±10%)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On a horizontal surface

 

 

 

 

Suspended from the ceiling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• For the case of installation in a special state such as ceiling mount, the specified mounting accessories (&69) and service may be required. Before installing the projector, consult your dealer about your installation.

 

a

 

 

 

16 : 10 screen

 

 

 

 

 

 

4 : 3 screen

 

 

 

 

 

 

b

 

 

c1

 

c2

 

 

b

 

 

c1

 

c2

Screen size

 

 

 

 

 

 

 

 

 

 

Projection distance

Screen

Screen

Projection distance

Screen

Screen

(diagonal)

 

 

 

 

 

height

height

 

 

 

 

height

height

min.

 

max.

min.

max.

 

 

 

type

m

m

inch

 

m

inch

cm

 

inch

cm

 

inch

m

inch

m

inch

cm

 

inch

cm

 

inch

(inch)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

0.8

0.9

36

 

1.1

44

38

 

15

3

 

1

1.0

41

1.3

50

42

 

18

3

 

1

40

1.0

1.2

49

 

1.5

59

50

 

20

4

 

2

1.4

56

1.7

67

57

 

22

4

 

2

50

1.3

1.6

61

 

1.9

74

63

 

25

5

 

2

1.8

70

2.1

84

71

 

28

5

 

2

60

1.5

1.9

74

 

2.3

89

75

 

30

6

 

2

2.1

84

2.6

101

85

 

33

7

 

3

70

1.8

2.2

87

 

2.7

105

88

 

34

7

 

3

2.5

99

3.0

119

99

 

39

8

 

3

80

2.0

2.5

100

 

3.0

120

100

 

39

8

 

3

2.9

113

3.5

136

113

 

45

9

 

3

90

2.3

2.9

112

 

3.4

135

113

 

44

9

 

3

3.2

127

3.9

153

127

 

50

10

 

4

100

2.5

3.2

125

 

3.8

150

125

 

49

10

 

4

3.6

142

4.3

170

142

 

56

11

 

4

120

3.0

3.8

150

 

4.6

181

150

 

59

12

 

5

4.3

170

5.2

205

170

 

67

13

 

5

150

3.8

4.8

188

 

5.8

227

188

 

74

14

 

6

5.4

214

6.5

257

212

 

84

18

 

6

200

5.1

6.4

252

 

7.7

303

250

 

98

19

 

8

7.2

285

8.7

343

283

 

111

22

 

9

250

6.4

8.0

315

 

9.6

379

313

 

123

24

 

9

9.1

357

10.9

429

354

 

139

27

 

11

300

7.6

9.6

379

 

11.6

455

375

 

148

29

 

11

10.9

429

13.1

515

425

 

167

33

 

13

7

Setting up

Arrangement (continued)

WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in fire and/or electric shock.

Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand.

Do not place the projector on its side, front or rear position.

Consult with your dealer before a special installation such as suspending from a ceiling or somewhere else.

►Place the projector in a cool place, and ensure that there is sufficient ventilation. The high temperature of the projector could cause fire, burns and/or malfunction of the projector.

Do not place or attach anything that would block the lens or vent holes.

Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

Do not place the projector on metallic thing or anything weak in heat.

Do not place the projector on carpet, cushions or bedding.

Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place anything near the projector lens or vents, or on top of the projector.

Do not place anything that may be sucked into or stick to the vents on the bottom of the projector. This projector has some intake vents also on the bottom.

►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause fire, electric shock and/or malfunction of the projector.

Do not place the projector in a bathroom or the outdoors.

Do not place anything containing liquid near the projector.

►Do not place the projector where any oils, such as cooking or machine oil, are used.

►Use only the mounting accessories the manufacturer specified, and leave installing and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause fire, electric shock and/or malfunction of the projector.

Do not place the projector near humidifiers, smoking spaces or a kitchen. Also do not use an ultrasonic humidifier near the projector. Otherwise chlorine and

minerals contained in tap water are atomized and could be deposited in the projector causing image degradation or other problems.

►Position the projector to prevent light from directly hitting the projector's remote sensor.

8

Setting up

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them. To input component video signal to COMPUTER IN port, please see the description of the COMPUTER IN item of the INPUT menu (&35).

Monitor

PC

RGB IN

AUDIO OUT

RGB OUT

AUDIO OUT

 

RS-232C

HDMI

S-VIDEOOUT

L

R

VIDEO OUT

L

R

L

R

Y

CB/PB CR/PR

 

AUDIO OUT

AUDIO OUT

AUDIO OUT

COMPONENT VIDEO OUT

 

 

 

 

 

 

 

 

 

 

 

L

R

 

 

 

 

 

 

 

 

 

 

AUDIO IN

VCR/DVD/Blu-rayDisc player

Speakers

(with an amplifier)

WARNING ►Do not disassemble or modify the projector and accessories. ►Be careful not to damage the cables, and do not use damaged cables.

CAUTION ►Turn off all devices and unplug their power cords prior to connecting them to projector. Connecting a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction or damage to the device and the projector.

►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specific length or a ferrite core by the regulations. For cables with a core only at one end, connect the end with the core to the projector.

►Make sure that devices are connected to the correct ports. An incorrect connection may result in malfunction or damage to the device and the projector.

NOTICE ►Use the cables with straight plugs, notL-shapedones, as the input ports of the projector are recessed.

9

Setting up

Connecting your devices (continued)

NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.

-Some signal may need an adapter to input this projector.

-Some PCs have multiple screen display modes that may include some signals which are not supported by this projector.

-Although the projector can display signals with resolution up to UXGA (1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

While connecting, make sure that the shape of the cable's connector fits the port to connect with. And be sure to tighten the screws on connectors with screws.

When connecting a laptop PC to the projector, be sure to activate the PC’s external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC.

When the picture resolution is changed on a PC depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original.

It might be recommended to use other CRT or LCD monitors to change the resolution.

In some cases, this projector may not display a proper picture or display

any picture on screen. For example, automatic adjustment may not function correctly with some input signals. An input signal of composite sync or sync on G may confuse this projector, so the projector may not display a proper picture.

About Plug-and-Playcapability

Plug-and-Playis a system composed of a PC, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible.Plug-and-Playcan be used by connecting this projector to a PC that is VESA DDC (display data channel) compatible.

Take advantage of this feature by connecting a computer cable to the COMPUTER IN port (DDC 2B compatible).Plug-and-Playmay not work properly if any other type of connection is attempted.

Please use the standard drivers in your PC as this projector is a Plug-and-Play monitor.

10

Connecting power supply

1. Put the connector of the power cord into theAC IN (AC inlet) of the projector.

2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, thePOWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated (&46), the connection of the power supply make the projector turn on.

Setting up

AC IN

Power cord

WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock.

Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one.

Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

Never modify the power cord.

Using the security bar and slot

Security slot

A commercially available anti-theftchain or wire can

 

be attached to the security bar on the projector.

 

Refer to the figure to choose an anti-theftchain or wire.

 

Also this product has the security slot for the

 

Kensington lock.

 

For details, see the manual of the security tool.

Security bar

 

12 mm

Anti-theftchain or wire

 

18 mm

18 mm

Installation surface

 

10 mm

 

WARNING ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION ►Do not placeanti-theftchain or wire near the exhaust vents. It may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention measures. It is intended to be used as supplemental theft prevention measure.

11

Remote control

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

1.

2.

3.

Holding the hook part of the battery

1

2

3

cover, remove it.

 

 

 

Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals

as indicated in the remote control.

Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets.

Do not recharge, short circuit, solder or disassemble a battery.

Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

Approx.

 

3 m

30º 30º

 

NOTE • The remote control signal reflected in the screen or the like may be available. If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.

The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

12

Power on/off

Turning on the power

Power on/off

STANDBY/ON button

POWER indicator

1. Make sure that the power cord is firmly and

correctly connected to the projector and the outlet.

2. Make sure that thePOWER indicator is

steady orange (63). Then remove the lens cover.

3. PressSTANDBY/ON button on the projector or the remote control. The projection lamp will light up andPOWER

indicator will begin blinking in green. When the power

is completely on, the indicator will stop blinking and light in steady green

(63).

To display the picture, select an input signal according to the section “Selecting an input signal” (15).

Turning off the power

1.

2.

3.

Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. ThenPOWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (63).

Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices.

• This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON (46) andAUTO POWER OFF (47) items of the OPTION menu.

13

Power on/off

Precaution for lens cover attachment and removal

When you attach or remove the lens cover, move it vertically up and down while keeping the knob to the right as illustrated in the figure.

14

Operating

Operating

Adjusting the volume

VOLUME +/-button

1. Use theVOLUME +/VOLUME - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

When is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (39).

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

 

 

 

MENU

Even if the projector is in the standby state, the volume can be adjusted when both of following conditions are satisfied.

-NORMAL is selected for the STANDBY MODE in the SETUP menu (38).

-An item other than is selected for the AUDIO OUT STANDBY of the AUDIO SOURCE in the AUDIO menu (39).

Temporarily muting the sound

1. PressMUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound.

To restore the sound, press the MUTE,VOLUME + orVOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (39).

MUTE button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

 

 

 

MENU

C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO orS-VIDEO,or 480i@60 forCOMPUTER

IN, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (45).

Selecting an input signal

1.

Press INPUT button on the projector.

INPUT button

Each time you press the button, the projector switches its

 

 

input port from the current port as below.

 

 

COMPUTER IN HDMI

 

 

VIDEO

S-VIDEO

 

While ON is selected for AUTO SEARCH item in OPTION menu (46), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

(continued on next page)

15

Operating

Selecting an input signal (continued)

Press COMPUTER button on the remote control to

COMPUTER button

1. select theCOMPUTER IN port.

 

 

 

 

 

VIDEO

 

MY SOURCE/

 

 

COMPUTER DOC.CAMERA

 

 

ASPECT

AUTO

SEARCH

BLANK

 

MAGNIFY

FREEZE

PAGE

VOLUME

 

ON

 

UP

 

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

 

KEYSTONE

MY BUTTON

MUTE

 

 

1

2

 

 

POSITION

 

 

MENU

1. PressVIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

HDMIS-VIDEOVIDEO

While ON is selected for AUTO SEARCH item in OPTION

menu, the projector will keep checking every port sequentially till an input signal is detected (46). IfVIDEO button is pressed whenCOMPUTER IN port is selected, the projector will checkHDMI port first.

VIDEO button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

 

 

 

MENU

Press the MY SOURCE / DOC. CAMERAbutton on

MY SOURCE /

1. the remote control. The input signal will be changed

DOC. CAMERA button

into the signal you set as MY SOURCE (48).

 

This function also can use for document camera. Select the input port that connected the document camera.

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

MENU

16

Searching an input signal

1. PressSEARCH button on the remote control.

The projector will start to check its input ports as below in order to find any input signals.

When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER INHDMI

VIDEO

S-VIDEO

Operating

SEARCH button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

 

 

 

MENU

While ON is selected for AUTO SEARCH item in OPTION menu (46), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

Selecting an aspect ratio

1. PressASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

For a computer signal

NORMAL 4:316:916:10NATIVE

ASPECT button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

For an HDMI signal

POSITION

MENU

NORMAL 4:316:916:1014:9NATIVE

 

 

For a video signal, s-videosignal or component video signal

4:3 16:916:1014:9NATIVE

For no signal

16:10 (fixed)

ASPECT button does not work when no proper signal is inputted.

NORMAL mode keeps the original aspect ratio setting.

17

Operating

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project ata suitable angle to the screen, elevating the front side of the12° projector within 12 degrees.This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is adjustable while pulling up the elevator knob on the same side as it.

1. Holding the projector, pull the elevator knobs up to loose the elevator feet.

2. Position the front side of the projector to the desired height.

3. Release the elevator knobs in order to lock the elevator feet.

4. Aftergently.making sure that the elevator feet are locked, put the projector down

5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet.

1

5

To loose an elevator foot, pull up the elevator knob on the same side as it.

To finely adjust, twist the foot.

CAUTION ►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

►Do not tilt the projector other than elevating its front within 12 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

Adjusting the zoom and focus

Zoom ring

1.

Use the zoom ring to adjust the screen size.

Focus ring

 

2.

Use the focus ring to focus the picture.

 

18

POSITION button

Operating

Using the automatic adjustment feature

1.

Press AUTO button on the remote control.

AUTO button

 

Pressing this button performs the following.

 

For a computer signal

MY SOURCE/ VIDEO COMPUTER DOC.CAMERA

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted.

Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

POSITION

 

 

 

MENU

For a video signal and s-videosignal

The video format best suited for the respective input signal will be selected

automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu (34). The vertical position and horizontal position will be automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (49).

Adjusting the position

1. Pressindicated.POSITION button on the remote control when no menu is The “POSITION” indication will appear on the screen.

2. Use the ▲/▼/◄/► cursor buttons to adjust the picture position. When you want to reset the operation, pressRESET button on the remote control during the operation.

To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

KEYSTONE

MY BUTTON

MUTE

 

1

2

POSITION

 

MENU

 

ENTER

 

ESC

 

RESET

● When this function is performed on a video signal or s-videosignal or component video signal, some image such as anextra-linemay appear at outside of the picture.

● When this function is performed on a video signal or an s-videosignal, the range of this adjustment depends on OVER SCAN in IMAGE menu (30) setting. It is not possible to adjust when OVER SCAN is set to 10.

● If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

● This function is unavailable for a signal from the HDMI port.

19

Operating

Correcting the keystone distortions

1. PressKEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion.

2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following.

(1)AUTO executes automatic vertical keystone correction.

(2)MANUAL displays a dialog for keystone correction. Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

KEYSTONE button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

The adjustable range of this function will vary among inputs. For some input, this function may not work well.

When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not work correctly.

When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-anglefocus) whenever possible.

When the projector is placed on the level (about ±4°), the automatic keystone distortion correction may not work.

When the projector is inclined to near ±30 degree or over, this function may not work well.

This function will be unavailable when Transition Detector is on (54).

20

Using the magnify feature

1. Press theMAGNIFY ON button on the remote control. The picture will be magnified, and the MAGNIFY dialog will appear on the screen. When theMAGNIFY ON button is pressed for the first time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

Operating

MAGNIFY ON/OFF button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

2.

3.

4.

5.

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor buttons to shift the magnifying area.

A magnifying glass icon will be displayed on the dialog when the MAGNIFY ON button is pressed while the dialog with the triangles is displayed.

While the magnifying glass icon is displayed on the dialog, use the ▲/▼ cursor buttons to adjust the magnification ratio. The magnification ratio will be adjusted with fine steps. And changes in the ratio in single steps are subtle so they may be hard to recognize.

Press the MAGNIFY OFF button on the remote control to exit magnification.

The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

While the MAGNIFY dialog is displayed, press the MAGNIFY ON button to switch the dialog between magnifying area shifting (with the triangles) and magnification ratio adjustment (with the magnifying glass icon).

The magnification is automatically disabled when the displaying signal or its display condition is changed.

While the magnification is active, the keystone distortion condition may vary. It will be restored when the magnification is disabled.

Some horizontal stripes might be visible on the image while magnification is active.

21

Operating

Temporarily freezing the screen

1. Press theFREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (42)), and the projector will go into the FREEZE mode, which the picture is frozen.

To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

FREEZE button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

The projector automatically exits from the FREEZE mode when some control buttons are pressed.

If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

Images might appear degraded when this function is operated, but it is not a malfunction.

Temporarily blanking the screen

1. Press theBLANK button on the control panel or the remote control. The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu (40).

To exit from the BLANK screen and return to the input signal screen, press BLANK button again.

The projector automatically exits from the BLANK mode when some control buttons are pressed.

You can change the function assigned to the BLANK button on the control panel by the MY BUTTON function.

Please refer to MY BUTTON item in OPTION menu

(48).

BLANK button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY

FREEZE

PAGE

 

VOLUME

ON

 

UP

 

 

 

 

 

OFF

 

DOWN

 

 

 

 

 

KEYSTONE

MY BUTTON

2

MUTE

 

1

 

 

BLANK button

%/$1.

0< %87721

CAUTION ►If you wish to have a blank screen while the projector's lamp is on, use the BLANK function above. Any other method of blocking the projection light, such as attaching something to the lens or placing something in front of the lens, may cause the damage to the projector.

NOTE • The sound is not connected with the BLANK screen function. If necessary, set the volume or mute first. To display the BLANK screen and mute the sound at one time, use AV MUTE function (48).

22

Operating

Using the menu function

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classified into each purpose and brought together as the ADVANCED MENU.

Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

INPUT button

ENTER button

MENU button

 

Cursor buttons

 

POSITION

MENU

 

ENTER

 

MENU button

ESC

RESET

(Cursor buttons)

 

 

 

ESC button

RESET button

1. To start the MENU, press theMENU button. The MENU you last used (EASY or ADVANCED) will appear. EASY MENU has priority to appear just after powered on.

2. In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select an item to operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1)Use the ▲/▼ cursor buttons to select a menu. If you want to change it to the EASY MENU, select the EASY MENU.

The items in the menu appear on the right side.

(2)Press the ► cursor button or ENTER button to move the cursor to the right side. Then use the

▲/▼ cursor buttons to select an item to operate and press the ► cursor button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3)Use the buttons as instructed in the OSD to operate the item.

(continued on next page)

23

Operating

Using the menu function (continued)

3. To close the MENU, press theMENU button again or select EXIT and press the ◄ cursor button orENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.

If you want to move the menu position, use the cursor buttons after pressing the

POSITION button.

Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) cannot be reset.

In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication

Meaning

 

 

EXIT

Selecting this word finishes the OSD menu. It's the same as

pressing the MENU button.

 

RETURN

Selecting this word returns the menu to the previous menu.

CANCEL or NO

Selecting this word cancels the operation in the present

menu and returns to the previous menu.

OK or YES

Selecting this word executes the prepared function or shifts

the menu to the next menu.

 

24

EASY MENU

EASYMENU

From the EASY MENU, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item

 

Description

 

ASPECT

Using the ◄/► buttons switches the mode for aspect ratio.

See the ASPECT item in IMAGE menu (30).

 

AUTO KEYSTONE

Using the ► button executes the auto keystone function.

See the AUTO KEYSTONE item in SETUP menu (37).

KEYSTONE

Using the ◄/► buttons corrects the vertical keystone distortion.

See the KEYSTONE item in SETUP menu (37).

 

 

Using the ◄/► buttons switches the picture mode.

 

The picture modes are combinations of GAMMA and COLOR

 

TEMP settings. Choose a suitable mode according to the projected

 

source.

 

 

 

NORMAL ó CINEMAó DYNAMICó BOARD(BLACK)

 

DAYTIME ó WHITEBOARDó BOARD(GREEN)

 

 

GAMMA

COLOR TEMP

 

NORMAL

1 DEFAULT

2 MID

PICTURE MODE

CINEMA

2 DEFAULT

3 LOW

DYNAMIC

3 DEFAULT

1 HIGH

 

BOARD(BLACK)

4 DEFAULT

4 Hi-BRIGHT-1

 

BOARD(GREEN)

4 DEFAULT

5 Hi-BRIGHT-2

 

WHITEBOARD

5 DEFAULT

2 MID

 

DAYTIME

6 DEFAULT

6 Hi-BRIGHT-3

When the combination of GAMMA and COLOR TEMP differs from pre-assignedmodes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP (27, 28) items in PICTURE menu.

Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

(continued on next page)

25

EASY MENU

Item

Description

ECO MODE

Using the ◄/► buttons changes the eco mode setting.

See the ECO MODE item in SETUP menu (38).

 

MIRROR

Using the ◄/► buttons switches the mode for mirror status.

See the MIRROR item in SETUP menu (38).

 

 

Performing this item resets all of the EASY MENU items except the

RESET

FILTER TIME and LANGUAGE.

A dialog is displayed for confirmation. Selecting the OK using the ►

 

 

button performs resetting.

 

The usage time of the air filter is shown in the menu.

 

Performing this item resets the filter time which counts usage time

FILTER TIME

of the air filter.

A dialog is displayed for confirmation. Selecting the OK using the ►

 

 

button performs resetting.

 

See the FILTER TIME item in OPTION menu (47).

LANGUAGE

Using the ◄/► buttons changes the display language.

See the LANGUAGE item in SCREEN menu (40).

 

ADVANCED MENU

Press the ► or ENTER button to use the menu of PICTURE,

 

IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION or SECURITY.

EXIT

Press the ◄ or ENTER button to finish the OSD menu.

26

PICTURE menu

PICTUREmenu

From the PICTURE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

 

Description

 

 

 

 

BRIGHTNESS

Using the ◄/► buttons adjusts the brightness.

 

Dark ó Light

 

 

 

 

 

CONTRAST

Using the ◄/► buttons adjusts the contrast.

 

Weak ó Strong

 

 

 

 

 

 

Using the ▲/▼ buttons switches the gamma mode.

 

 

DEFAULT-1CUSTOM-1DEFAULT-2CUSTOM-2DEFAULT-3

 

 

 

CUSTOM-6

 

CUSTOM-3

 

DEFAULT-5CUSTOM-4

 

DEFAULT-6CUSTOM-5

DEFAULT-4

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the mode.

This function is useful when you want to change the brightness of particular tones.

Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons.

GAMMA You can display a test pattern for checking the effect of your adjustment by pressing theENTER button.

Each time you press the ENTER button, the pattern changes as below.

No pattern ð Gray scale of 9 stepsRampGray scale of 15 steps

The eight equalizing bars correspond to eight tone levels of the test pattern (Gray scale of 9 steps) except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

• Lines or other noise might appear on the screen when this function is operated, but it

is not a malfunction.

(continued on next page)

27

PICTURE menu

Item

 

Description

 

 

 

 

Using the ▲/▼ buttons switches the color temperature mode.

 

1 HIGH

1 CUSTOM 2 MID

2 CUSTOM

 

 

 

6 CUSTOM

 

3 LOW

 

 

 

6 Hi-BRIGHT-3

 

3 CUSTOM

 

 

 

5 CUSTOM 5Hi-BRIGHT-24 CUSTOM

4Hi-BRIGHT-1

 

To adjust CUSTOM

 

 

 

 

Selecting a mode whose name includes

 

CUSTOM and then pressing the ► button

 

or the ENTER button displays a dialog

 

to aid you in adjusting the OFFSET and

COLOR TEMP

GAIN of the selected mode.

 

OFFSET adjustments change the color intensity

 

on the whole tones of the test pattern.

 

GAIN adjustments mainly affect color intensity

 

on the brighter tones of the test pattern.

 

Choose an item using the ◄/► buttons, and adjust the level using

 

the ▲/▼ buttons.

 

You can display a test pattern for checking the effect of your

 

adjustment by pressing the ENTER button.

 

Each time you press the ENTER button, the pattern changes as below.

 

No pattern ð Gray scale of 9 steps

 

 

 

 

 

 

Ramp Gray scale of 15 steps

 

 

 

• Lines or other noise might appear on the screen when

 

 

 

this function is operated, but it is not a malfunction.

 

 

 

 

 

 

 

 

Using the ◄/► buttons adjusts the strength of whole color.

 

Weak ó Strong

 

• This item can be selected only for a video, s-videoand component

COLOR

video signal.

 

• For an HDMI signal, this item can also be selected if either (1) or (2) applies.

 

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

 

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

 

projector recognizes that it receives video signals.

 

Using the ◄/► buttons adjusts the tint.

 

Reddish ó Greenish

 

• This item can be selected only for a video, s-videoand component

TINT

video signal.

 

• For an HDMI signal, this item can also be selected if either (1) or (2) applies.

 

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

 

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

 

projector recognizes that it receives video signals.

(continued on next page)

28

PICTURE menu

Item

 

Description

 

 

 

Using the ◄/► buttons adjusts the sharpness.

SHARPNESS

Weak

ó Strong

• There may be some noise and/or the screen may flicker for a

 

 

moment when an adjustment is made. This is not a malfunction.

 

This projector has 4 memories for adjustment data (for all the items

 

of the PICTURE menu).

 

Selecting a function using the ▲/▼ buttons and pressing the ► or

 

ENTER button performs each function.

 

SAVE-1ó SAVE-2ó SAVE-3ó SAVE-4

 

LOAD-4óLOAD-3ó LOAD-2ó LOAD-1

 

SAVE-1,SAVE-2,SAVE-3,SAVE-4

 

Performing a SAVE function saves the current adjustment data into

 

the memory linked in the number included in the function’s name.

 

• Remember that the current data being stored of a memory will be

 

lost by saving new data into the memory.

MY MEMORY LOAD-1, LOAD-2, LOAD-3, LOAD-4

Performing a LOAD function loads the data from the memory linked in the number included in the function’s name, and adjusts the picture automatically depending on the data.

The LOAD functions whose linked memory has no data are skipped.

Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.

There may be some noise and the screen may flicker for a moment when loading data. This is not malfunction.

You can perform the LOAD function using MY BUTTONs. Please see MY BUTTON item in OPTION menu (48).

29

IMAGE menu

IMAGEmenu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For a computer signal

 

NORMAL ó 4:3ó 16:9ó 16:10ó NATIVE

 

For an HDMI signal

ASPECT

NORMAL ó 4:3ó 16:9ó 16:10ó 14:9ó NATIVE

For a video signal, s-videosignal or component video signal

 

 

4:3 ó 16:9ó 16:10ó 14:9ó NATIVE

 

For no signal

 

16:10 (fixed)

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

Using the ◄/► buttons adjusts the over-scanratio.

 

Small (It magnifies picture) ó Large (It reduces picture)

 

• This item can be selected only for a video, s-videoand component

OVER SCAN

video signal.

 

• For an HDMI signal, this item can also be selected if either (1) or (2) applies.

 

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

 

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

 

projector recognizes that it receives video signals.

(continued on next page)

30

IMAGE menu

Item

Description

 

 

 

Using the ◄/► buttons adjusts the vertical position.

 

Down ó Up

Over-adjustingthe vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the

V POSITION default setting. Pressing theRESET button when the V POSITION is selected will reset the V POSITION to the default setting.

When this function is performed on a video signal or an s-videosignal, the range of this adjustment depends on OVER SCAN (30) setting. It is not possible to adjust when OVER SCAN is set to 10.

This function is unavailable for a signal from the HDMI port.

Using the ◄/► buttons adjusts the horizontal position. Right ó Left

Over-adjustingthe horizontal position may cause noise to appear on the screen. If this occurs, please reset the horizontal position to the

H POSITION default setting. Pressing theRESET button when the H POSITION is selected will reset the H POSITION to the default setting.

When this function is performed on a video signal or an s-videosignal, the range of this adjustment depends on OVER SCAN (30) setting. It is not possible to adjust when OVER SCAN is set to 10.

This function is unavailable for a signal from the HDMI port.

(continued on next page)

31

IMAGE menu

Item

Description

 

 

 

Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.

H PHASE

Right ó Left

• This item can be selected only for a computer signal or a

 

component video signal.

 

• This function is unavailable for a signal from the HDMI port.

 

Using the ◄/► buttons adjusts the horizontal size.

 

Small ó Large

 

• This item can be selected only for a computer signal.

 

• This function is unavailable for a signal from the HDMI port.

H SIZE

• When this adjustment is excessive, the picture may not be

 

displayed correctly. In such a case, please reset the adjustment

 

by pressing the RESET button on the remote control during this

 

operation.

 

• Images might appear degraded when this function is operated, but

 

it is not a malfunction.

 

Selecting this item performs the automatic adjustment feature.

 

For a computer signal

 

The vertical position, the horizontal position and the horizontal

 

phase will be automatically adjusted.

 

Make sure that the application window is set to its maximum size

 

prior to attempting to use this feature. A dark picture may still be

 

incorrectly adjusted. Use a bright picture when adjusting.

For a video signal and s-videosignal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT

menu (34). The vertical position and horizontal position will beAUTO ADJUST automatically set to the default.

EXECUTE For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

The items adjusted by this function may vary when the FINE or

DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (49).

32

INPUT menu

INPUTmenu

From the INPUT menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the progress mode.

 

TV ó FILMó OFF

• This function works only for a video signal, s-videosignal,

component video signal (of 480i@60 or 576i@50) and an HDMI PROGRESSIVE signal (of 480i@60 or 576i@50).

• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3Pull-Downconversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select OFF, even though the screen image may lose sharpness.

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH ó MIDó LOW

VIDEO NR

• This function works only for a video signal, s-videosignal, component video signal (of 480i@60 or 576i@50) and an HDMI signal (of 480i@60 or 576i@50).

Using the ▲/▼ buttons switches the mode for color space.

 

AUTO ó RGBó SMPTE240ó REC709ó REC601

COLOR SPACE

• This item can be selected only for a computer signal or a

 

component video signal.

The AUTO mode automatically selects the optimum mode.

The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.

(continued on next page)

33

INPUT menu

Item

Description

The video format for S-VIDEO port andVIDEO port can be set.

(1)Use the ▲/▼ buttons to select the input port.

S-VIDEOó VIDEO

(2)Using the ◄/► buttons switches the mode for video format.

VIDEO FORMAT

AUTO ó NTSCó PALó SECAM

 

N-PALó M-PALó NTSC4.43

This item is performed only for a video signal from the VIDEO port or theS-VIDEO port.

The AUTO mode automatically selects the optimum mode.

The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.

 

Using the ▲/▼ cursor buttons switches the video format for an

 

input from the HDMI port.

 

AUTO ó VIDEOó COMPUTER

 

 

 

 

 

 

Feature

 

HDMI FORMAT

 

 

 

AUTO

automatically sets the optimum mode.

 

 

VIDEO

sets the suitable mode for DVD signals.

 

 

COMPUTER

sets the suitable mode for computer signals.

 

 

• When the COMPUTER is selected, the functions COLOR

 

(PICTURE menu), TINT (PICTURE menu) and OVER SCAN

 

(IMAGE menu) are unavailable.

 

Using the ▲/▼ cursor buttons changes the digital range for input

 

from the HDMI port.

 

 

 

AUTO ó NORMALó ENHANCED

 

 

 

HDMI RANGE

 

Feature

 

 

 

 

AUTO

automatically sets the optimum mode.

 

 

 

 

NORMAL

sets the suitable mode for DVD signals. (16-235)

 

 

ENHANCED

sets the suitable mode for computer signals. (0-255)

 

 

• If the contrast of the screen image is too strong or too weak, try

 

finding a more suitable mode.

(continued on next page)

 

 

34

INPUT menu

Item

Description

 

 

 

Use the ◄/► buttons to select

 

the computer input signal type.

 

AUTO ó SYNC ON G OFF

 

• Selecting the AUTO mode allows you to input a sync on G signal

COMPUTER IN

or component video signal from the port. To input component

video signal to the projector, an RCA to D-subcable or adapter is

 

required.

 

• In the AUTO mode, the picture may be distorted with certain

 

input signals. In such a case, remove the signal connector so that

 

no signal is received and select the SYNC ON G OFF, and then

 

reconnect the signal.

 

Set the frame lock function on/off for each port.

 

(1) Use the ▲/▼ buttons to select the input ports.

 

COMPUTER IN ó HDMI

 

(2) Use the ◄/► buttons to turn the

FRAME LOCK

frame lock function on/off .

ON ó OFF

 

 

• This item can be performed only on a signal with a vertical

 

frequency of 50 to 60 Hz.

 

• When ON is selected, moving pictures are displayed more

 

smoothly.

(continued on next page)

35

CUSTOM

INPUT menu

Item

Description

The resolution for the COMPUTER IN input signals can be set on this projector.

(1)In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button.

The RESOLUTION menu will be displayed.

(2)In the RESOLUTION menu select the resolution you wish to display using the ▲/▼ buttons.

Selecting AUTO will set a resolution appropriate to the input signal.

(3)Pressing the ► or ENTER button when selecting a STANDARD resolution will

automatically adjust the horizontal and

vertical positions, clock phase and STANDARD horizontal size.

The INPUT_INFORMATION dialog will be displayed.

(4) To set a custom resolution use the ▲/▼ buttons to select

RESOLUTION the CUSTOM and the RESOLUTION_CUSTOM box will be displayed.

Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲/▼/◄/► buttons.

This function may not support all resolutions.

(5)Move the cursor to OK on screen and press the ► or ENTER button. The message “ARE YOU SURE YOU WISH TO CHANGE RESOLUTION?” appears. To save the setting, press the ► button.

The horizontal and vertical positions, clock phase and horizontal size will be automatically adjusted.

The INPUT_INFORMATION dialog will be displayed.

(6)To revert back to the previous resolution without saving changes, move the cursor to CANCEL on screen and press the

◄ or ENTER button.

The screen will then return to the RESOLUTION menu displaying the previous resolution.

• For some pictures, this function may not work well.

36

SETUP menu

SETUP menu

From the SETUP menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Selecting this item performs the Automatic keystone distortion

 

correction. Projector automatically corrects vertical keystone distortion

 

due to the (forward/backward) setup angle by itself.

 

This function will be executed only once when selected in the menu.

 

When the slant of the projector is changed, execute this function again.

 

• The adjustable range of this function will vary among inputs. For

 

some input, this function may not work well.

 

• When V:INVERT or H&V:INVERT is selected to the MIRROR item

 

in the SETUP menu, if the projector screen is inclined or angled

AUTO KEYSTONE

downward, this function may not work correctly.

 

• When the zoom adjustment is set to the TELE (telephoto focus),

 

this function may be excessive. This function should be used when

 

the zoom adjustment is set to the full WIDE (wide-anglefocus)

 

whenever possible.

 

• When the projector is placed on the level (about ±4°), this function

 

may not work.

 

• When the projector is inclined to near ±30 degree or over, this

 

function may not work well.

 

• This function will be unavailable when the Transition Detector is

 

on (54).

 

Using the ◄/► buttons corrects the vertical keystone distortion.

 

Shrink the bottom of the image ó Shrink the top of the image

KEYSTONE

• The adjustable range of this function will vary among inputs. For

 

some input, this function may not work well.

 

• This function will be unavailable when the Transition Detector is

 

on (54).

 

Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

AUTO ECO

ON ó OFF

• When ON is selected, the projector will always be set to Eco mode

MODE

at start-upregardless of the ECO MODE (38) setting. An OSD

 

message “AUTO ECO MODE” will be displayed for tens of seconds

 

when the projector starts with this function activated.

(continued on next page)

37

SETUP menu

Item

Description

 

Using the ▲/▼ buttons changes the eco mode setting.

ECO MODE

NORMAL ó ECO

• When the ECO is selected, acoustic noise and screen brightness

 

 

are reduced.

 

Using the ▲/▼ buttons switches the mode for mirror status.

MIRROR

NORMAL ó H:INVERTó V:INVERTó H&V:INVERT

 

If the Transition Detector is on and MIRROR status is changed,

 

TRANSITION DETECTOR ON alarm (54) will be displayed when

 

projector is restarted after the AC power is turned off.

 

Using ▲/▼ buttons switches the standby mode setting between

 

NORMAL and SAVING.

 

NORMAL ó SAVING

 

• When SAVING is selected and the projector is in the standby

 

state, the power consumption is lowered with some functional

STANDBY MODE

restrictions as below.

 

- The RS-232Ccommunication control is disabled except turning

 

the projector on and changing the STANDBY MODE setting.

 

- The STANDBY of the MONITOR OUT (below) is invalid, and no

 

signal is output from the MONITOR OUT port.

 

- The AUDIO OUT STANDBY of the AUDIO SOURCE (39) is

 

invalid, and no signal is output from the AUDIO OUT ports (5).

 

While the image signal from the input port chosen in step (1) is

 

projected, the image signal from the input port selected in step (2)

 

is output to MONITOR OUT port.

 

(1) Choose a picture input port using

 

▲/▼ buttons.

 

Choose STANDBY to select the

 

picture output in the standby mode.

 

(2) Select the output signal from the

MONITOR OUT

MONITOR OUT port using ◄/►

buttons.

 

Select OFF to disable the MONITOR

 

OUT port for the input port or standby

 

mode chosen in the step (1).

 

• If you have changed the setting of STANDBY, it applies only to

 

the current standby mode, NORMAL or SAVING, selected under

 

STANDBY MODE, without changing the setting of the other mode.

 

The factory settings are as follows:

 

- COMPUTER INforthe NORMALmodeof STANDBYMODE

 

- OFFforthe SAVINGmodeofSTANDBYMODE

38

AUDIO menu

AUDIO menu

From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

VOLUME

Using the ◄/► buttons adjusts the volume.

Low ó High

 

SPEAKER

Using the ▲/▼ buttons turns on/off the built-inspeaker.

ON ó OFF

 

When OFF is selected, the built-inspeaker does not work.

 

While the image signal from the input port chosen in step (1) is

 

projected, the audio signal from the input port selected in step

 

(2) is output to both the AUDIO OUT port andbuilt-inspeaker of

 

this projector. However, the built-inspeaker does not work when

 

SPEAKER is set to OFF.

 

(1) Choose a picture input port using

 

the ▲/▼ buttons.

 

Choose AUDIO OUT STANDBY

 

to select the sound output in the

 

standby mode.

 

(2) Select one of the AUDIO IN ports

AUDIO SOURCE

using ◄/► buttons.

Select to mute the sound from the input port or in the standby

 

 

mode chosen in the step (1).

 

• In the AUDIO SOURCE window, “H” symbolizes the audio signal

 

from the HDMI port. It can be selected only for the picture input

 

from the HDMI port.

 

• C.C. (Closed Caption) is automatically activated when is selected

 

and an input signal containing C.C. is received. This function is

 

available only when the signal is NTSC for VIDEO orS-VIDEO,

 

or 480i@60 for COMPUTER IN, and when AUTO is selected for

 

DISPLAY in the C.C. menu under the SCREEN menu (45).

 

• AUDIO OUT STANDBY is automatically set to OFF when SAVING

 

is selected for the STANDBY MODE item in the SETUP menu.

 

Using the ▲/▼ buttons switches the mode for the HDMI audio.

HDMI AUDIO

Check each of the two modes provided and select the suitable one

for your HDMI audio device.

 

 

1 ó 2

39

SCREEN menu

SCREEN menu

From the SCREEN menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼/◄/► buttons switches the OSD (On Screen

 

Display) language.

LANGUAGE

ENGLISH ó FRANÇAISó DEUTSCHó ESPAÑOL

 

(shown in the LANGUAGE dialog)

 

Press the ENTER orINPUT button to save the language setting.

Using the ▲/▼/◄/► buttons adjusts the menu position.

MENU POSITION To quit the operation, press theMENU button on the remote control or keep no operation for about 10 seconds.

Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature

(22). It is displayed by pressing theBLANK button on the remote control.

MyScreen ó ORIGINALó BLUEó WHITEó BLACK

BLANK

MyScreen : Screen can be registered by the MyScreen item (41).ORIGINAL : Screen preset as the standard screen.

BLUE, WHITE, BLACK : Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.

Using the ▲/▼ buttons switches the mode for the start-upscreen. Thestart-upscreen is a screen displayed when no signal or an unsuitable signal is detected.

MyScreen ó ORIGINALó OFF

MyScreen : Screen can be registered by the MyScreen item (41).START UP ORIGINAL : Screen preset as the standard screen.

OFF : Plain black screen.

To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen (22) after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.

When the ON is selected to the MyScreen PASSWORD item in the SECURITY menu (52), the START UP is fixed to MyScreen.

(continued on next page)

40

SCREEN menu

Item

Description

This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.

1.Selecting this item displays a dialog titled “MyScreen”. It will ask you if

you start capturing an image from the current screen.

Please wait for the target image to be displayed, and press the ENTER orINPUT button when the image is displayed. The image will freeze and the frame for capturing will appear.

To stop performing, press the RESET button on the remote control.

 

2. Using the ▲/▼/◄/► buttons adjusts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the frame position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Please move the frame to the position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MyScreen

of the image which you want to use. The

 

 

 

 

 

 

 

 

frame may not be able to be moved for

 

 

 

 

 

 

 

 

 

some input signals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To start registration, press the ENTER

 

or INPUT button on the remote control.

 

To restore the screen and return to the previous dialog, press the

 

RESET button on the remote control.

 

Registration takes several minutes.

 

When the registration is completed, the registered screen and the

 

following message is displayed for several seconds:

 

“MyScreen registration is finished.”

 

If the registration failed, the following message is displayed:

 

“A capturing error has occurred. Please try again.”

 

• This function cannot be selected when the ON is selected to the

 

MyScreen Lock item (42).

 

• This function cannot be selected when the ON is selected to the

 

MyScreen PASSWORD item in SECURITY menu (52).

 

• This function is unavailable for a signal from the HDMI port.

(continued on next page)

41

SCREEN menu

Item

Description

 

 

 

Using the ▲/▼ buttons turns on/off the MyScreen lock function.

 

ON ó OFF

MyScreen Lock

When the ON is selected, the item MyScreen is locked. Use this

 

function for protecting the current MyScreen.

 

• This function cannot be selected when the ON is selected to the

 

MyScreen PASSWORD item in SECURITY menu (52).

 

Using the ▲/▼ buttons turns on/off the message function.

 

ON ó OFF

 

When the ON is selected, the following message function works.

 

“AUTO IN PROGRESS” while automatically adjusting

 

“NO INPUT IS DETECTED”

 

“SYNC IS OUT OF RANGE”

 

“INVALID SCAN FREQ.”

 

“NOT AVAILABLE”

 

“Searching….” while searching for the input

MESSAGE

“Detecting….” while an input signal is detected

 

“AUTO ECO MODE” while starting up with AUTO ECO MODE

 

The indication of the input signal displayed by changing

 

The indication of the aspect ratio displayed by changing

 

The indication of the PICTURE MODE displayed by changing

 

The indication of the MY MEMORY displayed by changing

 

The indication of “FREEZE” and “II” while freezing the screen by

 

pressing the FREEZE button.

 

The indication of the TEMPLATE displayed by changing.

 

• When the OFF is selected, please remember if the picture is

 

frozen. Do not mistake freezing for a malfunction (22).

(continued on next page)

42

SCREEN menu

Item

Description

Each input port for this projector can have a name applied to it.

(1)Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button.

The SOURCE NAME menu will be displayed.

(2)Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. The SOURCE NAME dialog will be displayed. Right side of the menu is blank until a name is specified.

(3)Select an icon you'd like to assign to the port in the SOURCE NAME dialog. The name assigned to the port will also be automatically switched according to your icon selection. Press the ► or ENTER button to determine your icon selection.

(4)Select a number you'd like to assign for the port along with the icon. You can select the number either from blank (no number assigned), 1, 2, 3, or 4.

(5)If you'd like to modify the name assigned to the port, select CUSTOM NAME and

SOURCE NAME

press the ► button.

(6)The current name will be displayed on the first line. Use the ▲/▼/◄/► buttons and the ENTER orINPUT button to select and enter characters. To erase 1 character at one time, press theRESET button or press the ◄ andINPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press theENTER orINPUT button, 1 character or all characters will be erased. The name can be a maximum of 16 characters.

(7)To change an already inserted character, press the ▲ button to move the cursor to the first line, and use the ◄/► buttons to move the cursor on the character to be changed.

After pressing the ENTER orINPUT button, the character is selected. Then, follow the same procedure as described at the item (6) above.

(8)To finish entering text, move the cursor to the OK on screen and press the ►, ENTER orINPUT button. To revert to the previous name without saving changes, move the cursor to the CANCEL on screen and press the ◄,ENTER orINPUT button.

(continued on next page)

43

SCREEN menu

Item

 

Description

 

 

 

 

Using the ▲/▼ buttons switches the mode for the template screen.

 

Press the ► button to display the selected template, and press the

 

◄ button to close the displayed screen.

 

The last selected template is displayed when the MY BUTTON

 

allocated to the TEMPLATE function is pressed (48).

 

TEST PATTERN ó DOT-LINE1ó DOT-LINE2ó DOT-LINE3

 

 

MAP2 ó MAP1ó CIRCLE2ó CIRCLE1ó DOT-LINE4

TEMPLATE

You can turn a map upside down and scroll it horizontally when MAP1

or MAP2 is selected. To invert or scroll the map, display the guidance

 

 

by pressing the RESET button on the remote control three seconds or

 

more when MAP1 or MAP2 appears.

 

While the guidance is displayed:

 

• Press the ▲ cursor button and then press the ENTER orINPUT

 

button to place the Northern Hemisphere on the top.

 

• Press the ▼ cursor button and then press the ENTER orINPUT

 

button to place the Southern Hemisphere on the top.

 

• Press the ◄/► cursor button and then press the ENTER or

 

INPUT button to scroll the map horizontally.

(continued on next page)

44

SCREEN menu

Item

Description

 

 

 

The C.C. is the function that displays a

 

transcript or dialog of the audio portion of

 

a video, files or other presentation or other

 

relevant sounds. It is required to have NTSC

 

format video or 480i@60 format component

 

video source supporting C.C. feature to

 

utilize this function.

 

It may not work properly, depending on equipment or signal source.

 

In this case, please turn off the Closed Caption.

 

DISPLAY

 

Select Closed Caption DISPLAY setting from following options

 

using ▲/▼ buttons.

 

AUTO ó ONó OFF

AUTO : Closed Caption automatically displays when the volume is muted.

ON : Closed Caption is on.OFF : Closed Caption is off.

The caption is not displayed when the OSD menu is active.

The Closed Caption is the function to display the dialogue, narration, and / or sound effects of a television program or other

C.C.video sources. The Closed Caption availability is depending upon (Closed Caption) broadcaster and/or content.

MODE

Select Closed Caption MODE setting from following options using ▲/▼ buttons.

CAPTIONS ó TEXT

CAPTIONS : Display Closed Caption.

TEXT : Display Text data, which is for additional information such as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C. program has Text information.

CHANNEL

Select Closed Caption CHANNEL from following options using ▲/▼ buttons.

1 ó 2ó 3ó 4

1: Channel 1, primary channel / language

2: Channel 2

3: Channel 3

4: Channel 4

The channel data may vary, depending on the content. Some channel might be used for secondary language or empty.

45

OPTION menu

OPTION menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons turns on/off the automatic signal search

 

function.

 

ON OFF

AUTO SEARCH

When the ON is selected, detecting no signal automatically cycles

through input ports in the following order. The search is started from

 

the current port. Then when an input is found, the projector will stop

 

searching and display the image.

 

COMPUTER IN HDMI

 

VIDEO ï S-VIDEO

 

Using the ▲/▼ buttons turns on/off the automatic keystone function.

 

ON OFF

 

ON : Automatic keystone distortion correction will be executed

 

whenever changing the slant of the projector.

AUTO

OFF : This function is disabled. Please execute the AUTO

KEYSTONE

KEYSTONE in the SETUP menu for automatic keystone

 

distortion correction.

 

• When the projector is suspended from the ceiling this feature will

 

not function properly so select the OFF.

 

• This function will be unavailable when the Transition Detector is

 

on (54).

 

Using the ▲/▼ buttons turns on/off the DIRECT POWER ON

 

function.

 

ON OFF

 

When set to the ON, the lamp in projector will be automatically

 

turned on without the usual procedure (13), only when the

DIRECT POWER

projector is supplied with the power after the power was cut while

ON

the lamp was on.

 

• This function does not work as long as the power has been

 

supplied to the projector while the lamp is off.

 

• After turning the lamp on by the DIRECT POWER ON function,

 

if neither input nor operation is detected for about 30 minutes, the

 

projector is turned off, even though the AUTO POWER OFF function

 

(47) is disabled.

(continued on next page)

46

OPTION menu

Item

Description

 

 

 

Using the ▲/▼ buttons adjusts the time to count down to

 

automatically turn the projector off.

 

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

AUTO POWER

When the time is set to 0, the projector is not turned off automatically.

OFF

When the time is set to 1 to 99, and when the passed time with no-

 

signal or an unsuitable signal reaches at the set time, the projector

 

lamp will be turned off.

 

If one of the projector's buttons or the remote control buttons

 

is pressed or one of the commands (except get commands) is

 

transmitted to the CONTROL port during the corresponding time,

 

projector will not be turned off.

 

Please refer to the section “Turning off the power” (13).

 

The lamp time is the usage time of the lamp, counted after the last

 

resetting. It is shown in the OPTION menu.

 

Pressing the RESET button on the remote control or the ► button

 

of the projector displays a dialog.

LAMP TIME

To reset the lamp time, select the OK using the ► button.

CANCEL OK

 

Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

For the lamp replacement, see the section "Replacing the lamp"

(57, 58).

 

The filter time is the usage time of the air filter, counted after the last

 

resetting. It is shown in the OPTION menu.

 

Pressing the RESET button on the remote control or the ► button

 

of the projector displays a dialog.

FILTER TIME

To reset the filter time, select the OK using the ► button.

CANCEL OK

 

 

• Please reset the filter time only when you have cleaned or replaced

 

the air filter, for a suitable indication about the air filter.

 

• For the air filter cleaning, see the section “Cleaning and replacing

 

the air filter” (59, 60).

(continued on next page)

47

OPTION menu

Item

Description

 

You can use this item to assign one of the following functions to the

 

BLANK button on the control panel (5) and theMY BUTTON 1/2

 

buttons on the remote control (6).

 

(1) Choose a button to assign a function from BLANK, MY

 

BUTTON-1and MYBUTTON-2.Use the ▲/▼ buttons to select

 

the desired button on the menu and press the ► button.

 

(2) Then using the ▲/▼/◄/► buttons sets one of the following

 

functions to the chosen button. Press the ENTER orINPUT

 

button to save the setting.

 

• COMPUTER IN: Sets port to COMPUTER IN.

 

• HDMI: Selects input from HDMI port.

 

S-VIDEO:Sets port toS-VIDEO.

 

• VIDEO: Sets port to VIDEO.

 

• INFORMATION: Displays the INPUT_INFORMATION (50) or

 

the SYSTEM_INFORMATION or nothing.

 

• AUTO KEYSTONE : Performs automatic keystone distortion

 

correction (37).

 

• MY MEMORY: Loads one of adjustment data stored (29).

 

When more than one data are saved, the adjustment

MY BUTTON

changes every time the MY BUTTON is pressed.

 

When no data is saved in memory, the

 

dialog "No saved data" appears.

 

When the current adjustment is not

 

saved to memory, the dialog as shown in

 

the right appears.

 

If you want to keep the current adjustment, please press

 

the ► button to exit. Otherwise loading a data will overwrite the

 

current adjusted condition.

PICTURE MODE: Changes the PICTURE MODE (25).

FILTER RESET: Displays the filter time reset confirmation dialogue

(47).

TEMPLATE: Makes the template pattern selected to the TEMPLATE item (44) appear or disappear.

AV MUTE: Turns the picture and audio on/off.

RESOLUTION: Turns on/off the RESOLUTION dialog. (36)

ECO MODE: Turns on/off the ECO MODE dialog. (38)

BLANK: Turns on/off the blank function. (BLANK only)

FREEZE: Turns on/off the freeze function. (BLANK only)

VOLUME: Turns on/off the volume dialog. (BLANK only)

AUTO: Performs the automatic adjustment function. (BLANK only)

 

Using ▲/▼ buttons selects the picture input port to be selected with

 

pressing the MY SOURCE/DOC.CAMERA button on the remote

MY SOURCE

control.

Select the picture input that is connected with a document camera.

 

COMPUTER IN HDMI

 

VIDEO S-VIDEO

(continued on next page)

48

OPTION menu

Item

Description

 

 

 

Selecting this item displays the SERVICE

 

menu.

 

Select an item using the ▲/▼ buttons,

 

and press the ► button or the ENTER

 

button on the remote control to execute

 

the item.

 

FAN SPEED

 

Using the ▲/▼ buttons switches the rotation speed of the cooling

 

fans. The HIGH is the mode for use at highlands etc. Note that the

 

projector is noisier when the HIGH is selected.

 

HIGH ó NORMAL

 

AUTO ADJUST

 

Using the ▲/▼ buttons to select one of the mode. When the

 

DISABLE is selected, the automatic adjustment feature is disabled.

 

FINE ó FASTó DISABLE

 

FINE: Finer tuning including H.SIZE adjustment.

 

FAST: Faster tuning, setting H.SIZE to prearranged data for the

 

input signal.

 

• Depending on conditions, such as input image, signal cable to the

 

projector, environment around the projector, etc., the automatic adjustment

SERVICE

may not work correctly. In such a case, please choose DISABLE to disable

the automatic adjustment, and make adjustment manually.

 

GHOST

1.Select a color element of ghost using the ◄/► buttons.

2.Adjust the selected element using the ▲/▼ buttons to disappear ghost.

FILTER MESSAGE

Use the ▲/▼ button to set the timer for notifying by the message when to replace the filter unit

100h ó 200hó 500hó 1000hó 2000h

ó 3000hó 4000hó 5000hó OFF

After choosing an item except OFF, the message “REMINDER

***HRS PASSED .....” will appear after the timer reaches the interval time set by this feature (62).

When the OFF is chosen, the message will not appear. Utilize this feature to keep the air filter clean, setting the suitable time according to your environment of this projector.

Please take care of the filter unit periodically, even if there is no message. If the air filter becomes to be blocked by dust or other matter, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

Please be careful with the operating environment of the projector and the condition of the filter unit.

(continued on next page)

49

OPTION menu

Item

Description

 

 

 

KEY LOCK

 

Using the ▲/▼ buttons turns on/off the key lock feature. When ON

 

is selected, the buttons on the projector except the STANDBY/ON

 

button are locked.

 

ON ó OFF

 

• Please use this function to prevent tampering or accidental

 

operation. This function does not have any effect on the remote

 

control.

 

INFORMATION

 

Selecting this item displays a dialog titled “INPUT_INFORMATION”.

 

It shows the information about the current input.

SERVICE (continued)

The “FRAME LOCK” message on the dialog means the frame lock function is working.

This item can't be selected for no signal and sync out.

When the MY TEXT DISPLAY is set to ON, the MY TEXT is

displayed together with the input information in the INPUT_ INFORMATION box (56).

FACTORY RESET

Selecting OK using the ► button performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the LAMP TIME, FILTER TIME,

LANGUAGE, FILTER MESSAGE, SECURITY settings, and others are not reset.

CANCEL OK

50

SECURITY menu

SECURITY menu

This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed.

To use SECURITY menu: User registration is required before using the security functions.

Enter the SECURITY menu

1.Use the ▲/▼ buttons on the SECURITY menu to select ENTER PASSWORD and press the ► button. The ENTER PASSWORD box will be displayed.

2.Use the ▲/▼/◄/► buttons to enter the registered password.

The factory default password is 4610. This password can be changed (below). Move the cursor to the right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.

It is strongly recommended the factory default password to be changed as soon as possible.

If an incorrect password is input, the ENTER PASSWORD box will be displayed again. If incorrect password is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.

3.Items shown in the table below can be performed.

If you have forgotten your password

(1). While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold theINPUT button for 3 seconds while pressing the ► button on the projector.

(2). The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).

Item

 

Description

 

 

 

 

(1)

Use the ▲/▼ buttons on the SECURITY menu

 

 

to select SECURITY PASSWORD CHANGE

 

 

and press the ► button to display the ENTER

 

 

NEW PASSWORD box.

 

(2)

Use the ▲/▼/◄/► buttons to enter the new password.

 

(3)

Move the cursor to the right side of the

SECURITY

 

ENTER NEW PASSWORD box and press the

 

► button to display the NEW PASSWORD

PASSWORD

 

AGAIN box, enter the same password again.

CHANGE

(4) Move the cursor to the right side of the NEW

 

 

PASSWORD AGAIN box and press the ►

 

 

button and the NOTE NEW PASSWORD box

 

 

will be displayed for about 30 seconds, please

 

 

make note of the password during this time.

 

 

Pressing the ENTER button on the remote control or ► button on the

 

 

projector will close the NOTE NEW PASSWORD box.

 

• Please do not forget your password.

(continued on next page)

51

SECURITY menu

Item

Description

 

 

 

 

The MyScreen PASSWORD function can be used to prohibit access to the

 

MyScreen function and prevent the currently registered MyScreen image

 

from being overwritten.

 

 

1 Turning on the MyScreen PASSWORD

 

 

1-1Use the ▲/▼ buttons on the SECURITY menu to

 

select MyScreen PASSWORD and press the ►

 

 

button to display the MyScreen PASSWORD on/

 

 

off menu.

 

 

1-2Use the ▲/▼ buttons on the MyScreen

 

 

PASSWORD on/off menu to select ON.

 

 

The ENTER NEW PASSWORD box (small)

 

 

will be displayed.

ENTER NEW PASSWORD

 

1-3Use the ▲/▼/◄/► buttons to enter the

box (small)

 

password. Move the cursor to the right side

 

 

of the ENTER NEW PASSWORD box (small)

 

 

and press the ► button to display the NEW

 

 

PASSWORD AGAIN box, enter the same

 

 

PASSWORD again.

 

1-4Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note of the password during this time.

Pressing the ENTER button on the remote control or ► button on theMyScreen projector will return to MyScreen PASSWORD on/off menu.

PASSWORD When a password is set for MyScreen:

The MyScreen registration function (and menu) will be unavailable.

The MyScreen Lock menu will be unavailable.

The START UP setting will be locked on MyScreen (and the menu will be unavailable).

Turning the MyScreen PASSWORD off will allow normal operation of these functions.

Please do not forget your MyScreen PASSWORD.

2 Turning off the MyScreen PASSWORD

2-1Follow the procedure in1-1to display the MyScreen PASSWORD on/off

menu.

 

2-2Select OFF to display the ENTER

 

PASSWORD box (large). Enter the registered

 

password and the screen will return to the

ENTER PASSWORD box

MyScreen PASSWORD on/off menu.

If an incorrect PASSWORD is input, the menu will

(large)

 

close. If necessary, repeat the process from 2-1.

 

3 If you have forgotten your password

3-1Follow the procedure in1-1to display the MyScreen PASSWORD on/off menu.

3-2Select OFF to display the ENTER PASSWORD box (large). The 10 digit

Inquiring Code will be displayed inside the box.

3-3Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.

(continued on next page)

52

SECURITY menu

Item

Description

 

 

 

PIN LOCK is a function which prevents the projector from being used unless

 

a registered Code is input.

 

1 Turning on the PIN LOCK

 

1-1Use the ▲/▼ buttons on the SECURITY menu

 

to select PIN LOCK and press the ► button or

 

the ENTER button to display the PIN LOCK on/

 

off menu.

 

1-2Use the ▲/▼ buttons on the PIN LOCK on/

 

off menu to select ON and the Enter PIN

 

Code box will be displayed.

 

1-3Input a 4 part PIN code using the ▲/▼/◄/►,

 

COMPUTER or INPUTbutton.

 

The PIN Code again box will appear. Reenter

 

the same PIN code. This will complete the PIN

 

code registration.

 

If there is no key input for about 55 seconds

 

while the Enter PIN Code box or the PIN Code again box is displayed,

 

the menu will close. If necessary, repeat the process from 1-1.

 

Afterwards, anytime the projector is restarted after AC power is turned off

 

the Enter PIN Code box will be displayed. Enter the registered PIN code.

 

The projector can be used after entering the registered PIN code. If an

 

incorrect PIN code is input, the Enter PIN code box will be displayed again.

PIN LOCK

If an incorrect PIN Code is input 3 times, the projector will turn off.

 

Afterwards the projector will turn off every time an incorrect PIN code is

 

input. The projector will also turn off if there is no key input for about 5

 

minutes while the Enter PIN code box is displayed.

 

This function will activate only when the projector is started after AC power

 

is turned off.

 

Please do not forget your PIN code.

 

2 Turning off the PIN LOCK

 

2-1Follow the procedure in1-1to display the PIN LOCK on/off menu.

 

2-2Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be

 

displayed.

 

Enter the registered PIN code to turn the PIN LOCK function off.

 

If an incorrect PIN Code is input 3 times, the menu will close.

 

3 If you have forgotten your PIN Code

 

3-1While the Enter PIN Code box is displayed, press and hold theRESET

 

button for three seconds or press and hold the INPUT button for 3

 

seconds while pressing the ► button on the projector.

 

The 10 digit Inquiring Code will be displayed.

 

If there is no key input for about 5 minutes

 

while the Inquiring Code is displayed, the

 

projector will turn off.

 

3-2Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will

 

be sent after your user registration information is confirmed.

(continued on next page)

53

SECURITY menu

Item

Description

TRANSITION DETECTOR

If this function is set to ON when the vertical angle of the projector or MIRROR setting at which the projector is turned on is different than the previously recorded, the TRANSITION DETECTOR ON alarm will be displayed and the projector will not display the input signal.

To display the signal again, set this function OFF.

After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, the lamp will turn off.

Keystone adjustment feature has been prohibited as long as the Transition Detector function is on.

1 Turning on the TRANSITION DETECTOR

1-1Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or theENTER button to display the TRANSITION DETECTOR on/off menu.

1-2Use the ▲/▼ buttons on the TRANSITION DETECTOR on/off menu to select ON. Select ON and the current angle and MIRROR setting will be recorded. The ENTER NEW PASSWORD box (small) will be displayed.

1-3Use the ▲/▼/◄/► buttons to enter a password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again.

ENTER NEW PASSWORD box (small)

1-4Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note of the password during this time.

Pressing the ENTER button on the remote control or the ► button on the projector will return to the TRANSITION DETECTOR on/off menu.

Please do not forget your TRANSITION DETECTOR password.

This function will activate only when the projector is started after turning off the AC power.

This feature may not function properly if the projector is not in a stable position when ON is selected.

2 Turning off the TRANSITION DETECTOR

2-1Follow the procedure in1-1to display the TRANSITION DETECTOR on/off menu.

2-2Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the TRANSITION DETECTOR on/off menu.

If an incorrect password is input, the menu will

close. If necessary, repeat the process from 2-1.ENTER PASSWORD box (large)

3 If you have forgotten your password

3-1Follow the procedure in1-1to display the TRANSITION DETECTOR on/off menu.

3-2Select OFF to display the ENTER PASSWORD box (large). The 10 digit

Inquiring Code will be displayed inside the box.

3-3Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.

(continued on next page)

54

SECURITY menu

Item

Description

MY TEXT

PASSWORD

The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;

The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.

The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.

1 Turning on the MY TEXT PASSWORD

1-1Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT PASSWORD and press the ► button to display the MY TEXT PASSWORD on/off menu.

1-2Use the ▲/▼ buttons on the MY TEXT PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.

1-3Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, and then enter the same password again.

1-4Move the cursor to the right side of the NEW PASSWORD AGAIN box and press ► button to display the NOTE NEW PASSWORD box for about 30 seconds, then please make note of the password during this time.

ENTER NEW PASSWORD box (small)

Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu.

2 Turning off the MY TEXT PASSWORD

2-1Follow the procedure in1-1to display the MY TEXT PASSWORD on/off menu.

2-2Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the MY TEXT PASSWORD on/off menu.

If an incorrect password is input, the menu will close. If necessary, repeat the process from 2-1

3 If you have forgotten your password

ENTER PASSWORD box (large)

3-1Follow the procedure in1-1to display the MY TEXT PASSWORD on/off menu.

3-2Select OFF to display the ENTER PASSWORD box (large). The 10 digit inquiring code will be displayed inside the box.

3-3Contact your dealer with the 10 digit inquiring code. Your password will be sent after your user registration information is confirmed.

(continued on next page)

55

SECURITY menu

Item

Description

 

 

 

(1) Use the ▲/▼ buttons on the SECURITY menu to

 

select the MY TEXT DISPLAY and press the ►

 

button to display the MY TEXT DISPLAY on/off

 

menu.

 

(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select

 

on or off.

MY TEXT

ON ó OFF

DISPLAY

When it is set ON, the MY TEXT will be displayed

 

on the START UP screen and the INPUT_

 

INFORMATION when the INFORMATION on the

 

SERVICE menu is chosen.

 

• This function is available only when the MY TEXT

 

PASSWORD function is set to the OFF.

 

 

 

(1) Use the ▲/▼ buttons on the

 

SECURITY menu to select the MY

 

TEXT WRITING and press the ►

 

button. The MY TEXT WRITING dialog

 

will be displayed.

 

(2) The current MY TEXT will be displayed

 

on the first 3 lines. If not yet written, the

 

lines will be blank.

 

Use the ▲/▼/◄/► buttons and the

 

ENTER orINPUT button to select and

 

enter characters. To erase 1 character

 

at one time, press the RESET button

 

or press the ◄ and INPUT button at

 

the same time. Also if you move the

 

cursor to DELETE or ALL CLEAR on

MY TEXT

screen and press the ENTER orINPUT

button, 1 character or all characters will

WRITING

be erased. The MY TEXT can be input

 

up to 24 characters on each line.

 

(3) To change an already inserted

 

character, press the ▲/▼ button to

 

move the cursor to one of the first 3

 

lines, and use the ◄/► buttons to

 

move the cursor on the character to be

 

changed.

 

After pressing the ENTER orINPUT button, the character is selected.

 

Then, follow the same procedure as described at the item (2) above.

 

(4) To finish entering text, move the cursor to the OK on screen and press

 

the ►, ENTER orINPUT button. To revert to the previous MY TEXT

 

without saving changes, move the cursor to the CANCEL on screen and

 

press the ◄, ENTER orINPUT button.

 

The MY TEXT WRITING function is available only when the MY TEXT

 

PASSWORD function is set to OFF.

56

Maintenance

Maintenance

Replacing the lamp

A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number.

Type number : 456-8789H

Lamp cover

 

Replacing the lamp

1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes.

2. Prepare a new lamp. If the projector is mounted on a ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

3. Loosen the screw (marked by arrow) of the lamp cover and then slide and lift the lamp cover to the side to remove it.

4. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handle.Never loosen any other screws.

5. Insert the new lamp, and retighten firmly the 2 screws of the lamp that are loosened in the previous process to lock it in place.

6. While putting the interlocking parts of the lamp cover and the projector together, slide the lamp cover back in place. Then firmly fasten the screw of the lamp cover.

7. Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu.

(1)Press the MENU button to display a menu.

(2)Point at the ADVANCED MENU in the menu using the ▼/▲ button, then press the ► button.

(3)Point at the OPTION in the left column of the menu using the ▼/▲ button, then press the ► button.

3

Handle

6

(4)Point at the LAMPTIME using the ▼/▲ button, then press the ► button.Adialog will appear.

(5)Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.

CAUTION ►Do not touch any inner space of the projector, while the lamp is taken out.

NOTE • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

57

Maintenance

Replacing the lamp (continued)

Lamp warning

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

 

WARNING ►The projector uses ahigh-pressuremercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, if the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury and dust containing fine particles of glass to escape from the projector’s vent holes.

About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

For lamp recycling, go to www.lamprecycle.org (in the US).

For product disposal, consult your local government agency or www.eiae.org (in the US) orwww.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does), ventilate the

the plug

room well, and make sure not to inhale the gas or fine particles that come out

from the

from the projector's vent holes, and not to get them into your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the lamp.

Never unscrew except the appointed (marked by an arrow) screws.

Do not open the lamp cover while the projector is suspended from a ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Use only the lamp of the specified type. Use of a lamp that does not meet the lamp specifications for this model could cause a fire, damage or shorten the life of this product.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, consult your local dealer or a service representative.

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

58

Maintenance

Cleaning and replacing the air filter

The air filter unit of this projector consists of a filter cover, two kinds of filters, and a filter frame. The new double large filters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector.

When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible. Replace the filters when they are damaged or too soiled. To prepare new filters, make contact with your dealer and tell the following type number.

Type number : UX36761 (Filter set)

When you replace the lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector.

Turn the projector off, and unplug the power cord.

2

1. Allow the projector to sufficiently cool down.

 

2. Use a vacuum cleaner on and around the filter cover.

3. Pick and pull up the filter cover knobs to take it off.

Filter cover

 

3

Use a vacuum cleaner for the filter vent of the

 

4. projector.

 

Take the fine meshed filter out while holding the

 

5. filter cover. It is recommended to leave the coarse

Filter cover knobs

meshed filter in the filter cover as it is.

4

Use a vacuum cleaner on both sides of the fine

 

6. meshed filter while holding it so it will not be

 

sucked in. Use a vacuum cleaner for the inside of

Intake vent

the filter cover to clean up the coarse meshed filter.

7

If the filters are damaged or heavily soiled, replace

them with new ones.

 

Put the fine meshed filter on the coarse meshed

 

7. one, turning its stitched side up.

Filter (coarse meshed)

 

8. Put the filter unit back into the projector.

Filter (fine meshed)

 

Stitched

side

(continued on next page)

59

Maintenance

Cleaning and replacing the air filter (continued)

9. Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU.

(1)Press the MENU button to display a menu.

(2)Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear.

(3)Press the ► button to select “OK” on the dialog. It performs resetting the filter time.

WARNING ►Before taking care of the air filter, make sure the power cable is not plugged in, then allow the projector to cool sufficiently. Taking care of the air filter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector.

►Use only the air filter of the specified type. Do not use the projector without the air filter or the filter cover. It could result in a fire or malfunction to the projector. ►Clean the air filter periodically. If the air filter becomes clogged by dust or the like, internal temperatures rise and could cause a fire, a burn or malfunction to the projector.

NOTE • Please replace the air filter when it is damaged or too soiled.

When you replace the projection lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector.

Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter.

The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

60

Maintenance

Other care

Inside of the projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year.

Caring for the lens

If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling.

1.

2.

Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.

After making sure that the projector is cool adequately, lightly wipe the lens with a commercially available lens-cleaningwipe. Do not touch the lens directly with your hand.

Caring for the cabinet and remote control

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

1.

2.

Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.

After making sure that the projector is cool adequately, lightly wipe with gauze or a soft cloth.

If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

WARNING ►Before caring, make sure the power cord is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector.

►Never try to care for the inside of the projector personally. Doing is so dangerous.

►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and/or malfunction to the projector.

Do not put anything containing water, cleaners or chemicals near the projector.

Do not use aerosols or sprays.

CAUTION ►Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc.

►Do not use cleaners or chemicals other than those specified in this manual. ►Do not polish or wipe with hard objects.

61

Troubleshooting

Troubleshooting

If an abnormal operation should occur, stop using the projector immediately.

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact to your dealer or service company.

Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair.

If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Related messages

When some message appears, check and cope with it according to the following table. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

 

 

 

There is no input signal.

 

Please confirm the signal input connection, and the status

 

of the signal source.

 

The horizontal or vertical frequency of the input signal is

 

not within the specified range.

 

Please confirm the specs for your projector or the signal

 

source specs.

 

An improper signal is input.

 

Please confirm the specs for your projector or the signal

 

source specs.

The internal temperature is rising.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again.

Is there blockage of the air passage aperture?

Is the air filter dirty?

Does the peripheral temperature exceed 35°C?

If the same indication is displayed after the remedy, please set

FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

A note of precaution when cleaning the air filter.

Please immediately turn the power off, and clean or change the air filter referring to the “Cleaning and replacing the

air filter” section of this manual. After you have cleaned or

changed the air filter, please be sure to reset the filter timer

(47).

The button operation is not available(6).

62

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP,TEMP andPOWER indicators differs from usual, check and cope with it according to the following table.

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

Lighting

Turned

Turned

The projector is in a standby state.

In Orange

off

off

Please refer to the section “Power on/off”.

Blinking

Turned

Turned

The projector is warming up.

In Green

off

off

Please wait.

Lighting

Turned

Turned

The projector is in an on state.

In Green

off

off

Ordinary operations may be performed.

Blinking

Turned

Turned

The projector is cooling down.

In Orange

off

off

Please wait.

 

 

 

The projector is cooling down. A certain error

Blinking

(discre-

(discre-

has been detected.

In Red

tionary)

tionary)

Please wait until POWER indicator finishes blinking,

and then perform the proper measure using the item

 

 

 

descriptions below.

 

 

 

The lamp does not light, and there is a possibility

 

 

 

that interior portion has become heated.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

Lighting

Turned

sufficiently cooled down, please make confirmation of

or

In Red

off

the following items, and then turn the power on again.

Lighting

• Is there blockage of the air passage aperture?

 

 

In Red

 

 

• Is the air filter dirty?

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please

 

 

 

change the lamp referring to the section “Replacing the lamp”.

 

 

 

The lamp cover has not been properly fixed.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 45 minutes. After the projector has

In Red

Blinking

Turned

sufficiently cooled down, please make confirmation of

or

In Red

off

the attachment state of the lamp cover. After performing

Lighting

 

 

any needed maintenance, turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

 

 

 

The cooling fan is not operating.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

Turned

Blinking

sufficiently cooled down, please make confirmation

or

off

In Red

that no foreign matter has become caught in the fan,

Lighting

 

 

etc., and then turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

(Continued on next page)

 

63

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

Blinking

 

 

Please turn the power off, and allow the projector to cool down at least

 

 

20 minutes.After the projector has sufficiently cooled down, please make

In Red

 

 

Turned

Lighting

confirmation of the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please set FAN

 

 

 

SPEED of SERVICE item in OPTION menu to HIGH (49).

 

 

 

It is time to clean the air filter.

Lighting

Simultaneous

Please immediately turn the power off, and clean or

change the air filter referring to the section “Cleaning

In Green

blinking in Red

and replacing the air filter”. After cleaning or changing

 

 

 

the air filter, please be sure to reset the filter timer.

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

NOTE • When the interior portion has become overheated, for safety

purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (50) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.) to the factory default.

64

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

11

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

11, 13

 

Please disconnect the power plug from the power outlet,

Power does not

and allow the projector to cool down at least 10 minutes,

 

then turn the power on again.

 

come on.

 

 

Either there is no lamp and/or lamp cover, or either

 

 

 

 

of these has not been properly fixed.

 

 

Please turn the power off and disconnect the power plug from

57, 58

 

the power outlet, and allow the projector to cool down at least

 

45 minutes. After the projector has sufficiently cooled down,

 

 

please make confirmation of the attachment state of the lamp

 

 

and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

9

 

Correctly connect the connection cables.

 

 

 

Signal source does not correctly work.

 

Correctly set up the signal source device by referring to the

 

manual of the source device.

 

Neither sounds

The input changeover settings are mismatched.

15, 16

nor pictures are

Select the input signal, and correct the settings.

outputted.

 

 

The BLANK function for pictures and the MUTE

 

 

 

 

function for sounds are working.

 

 

AV MUTE may be active.

15, 22,

 

Refer to the item “Sound does not come out” and “No

48

 

pictures are displayed” on the next page to turn off the

 

 

MUTE and BLANK functions.

 

(Continued on next page)

 

65

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The signal cables are not correctly connected.

9

 

Correctly connect the audio cables.

 

 

 

The MUTE function is working.

15

 

Restore the sound pressing the MUTE orVOLUME +/-

 

button on the remote control.

 

Sound does not

The volume is adjusted to an extremely low level.

15

Adjust the volume to a higher level using the menu function

come out.

or the remote control.

 

 

The AUDIO SOURCE/SPEAKER setting is not correct.

39

 

Correctly set the AUDIO SOURCE/SPEAKER in the AUDIO

 

menu.

 

 

The mode selected for HDMI AUDIO is not suitable.

39

 

Check each of the two modes provided and select the

 

suitable one for your HDMI audio device.

 

 

The lens cover is attached.

14

 

Remove the lens cover.

 

 

 

The signal cables are not correctly connected.

9

 

Correctly connect the connection cables.

 

 

 

The brightness is adjusted to an extremely low level.

27

No pictures are

Adjust the BRIGHTNESS to a higher level using the menu

function.

 

displayed.

 

 

The computer cannot detect the projector as a plug

 

 

 

 

and play monitor.

10

 

Make sure that the computer can detect a plug and play

 

 

 

monitor using another plug and play monitor.

 

 

The BLANK screen is displayed.

22

 

Press the BLANK button on the control panel or the remote

 

control.

 

Video screen

The FREEZE function is working.

22

display freezes.

Press the FREEZE button to restore the screen to normal.

 

 

Color settings are not correctly adjusted.

 

Colors have a

Perform picture adjustments by changing the COLOR

28, 33

fadedout

TEMP, COLOR, TINT and/or COLOR SPACE settings,

 

appearance, or

using the menu functions.

 

Color tone is

The COLOR SPACE setting is not suitable.

 

poor.

Change the COLOR SPACE setting to the AUTO, RGB,

33

 

SMPTE240, REC709 or REC601.

 

(Continued on next page)

66

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The brightness and/or contrast are adjusted to an

 

 

extremely low level.

27

 

Adjust the BRIGHTNESS and/or CONTRAST settings to a

 

 

 

higher level using the menu function.

 

Pictures appear

The ECO MODE function is working.

 

dark.

Select the NORMAL for the ECO MODE item in the SETUP

38

 

menu.

 

 

The lamp is approaching the end of its product

 

 

lifetime.

57, 58

 

Replace the lamp.

 

 

Either the focus and/or horizontal phase settings are

 

 

not properly adjusted.

18, 32

Pictures appear

Adjust the focus using the focus ring, and/or the H PHASE

 

blurry.

using the menu function.

 

 

The lens is dirty or misty.

61

 

Clean the lens referring to the section “Caring for the lens”.

 

 

No signal is

The SAVING function is working in the standby state.

 

output from the

Select the NORMAL for the STANDBY MODE item in the

 

MONITOR OUT

SETUP menu.

 

and AUDIO

 

38

OUT ports.

 

 

RS-232Cdoes

 

 

not work.

 

 

 

When the projector is operating in Eco mode,

 

 

flickering may appear on screen.

37, 38

Some kind

Set ECO MODE to NORMAL, and set AUTO ECO MODE to

OFF, in the SETUP menu.

 

of image

 

 

The OVER SCAN ratio is too big.

 

degradation

30

Adjust OVER SCAN in the IMAGE menu smaller.

such as

 

flickering or

Excessive VIDEO NR.

33

stripes appear

Change the setting of VIDEO NR in the INPUT menu.

on the screen.

 

 

The FRAME LOCK function cannot work on the

 

 

 

 

current input signal.

35

 

Set FRAME LOCK in the INPUT menu to OFF.

 

(Continued on next page)

 

67

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

NOTE • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect.

• The projector may make a rattling sound when tilted, moved or shaken, since a flap to control the air flow inside of the projector has moved. Be aware that this is not a failure or malfunction.

68

 

 

Specifications

Specifications

 

 

Specifications

 

 

Item

Specification

 

Product name

Liquid crystal projector

 

Liquid Crystal Panel

1,024,000 pixels (1280 horizontal x 800 vertical)

Lamp

200 W UHB

 

Speaker

1 W

 

Power supply

AC 100-120V/2.9 A, AC220-240V/1.4 A

Power consumption

AC 100-120V/290 W, AC220-240V/270 W

Temperature range

5 ~ 35 °C (Operating)

 

Size

306 (W) x 77 (H) x 221 (D) mm

 

* Not including protruding parts. Please refer to the following figure.

 

Weight (mass)

approx. 2.2 kg

 

 

Computer input port

 

 

COMPUTER IN ...................................

D-sub15 pin mini x1

 

Computer output port

 

 

MONITOR OUT ...................................

D-sub15 pin mini x1

 

HDMI input port

 

 

HDMI .....................................................

HDMI connector x1

 

Video input port

 

Ports

S-VIDEO...................................................

mini DIN 4 pin x1

 

VIDEO......................................................................

RCA x1

 

Audio input/output port

 

 

AUDIO IN1.....................................................

Stereo mini x1

 

AUDIO IN2.....................................................

Stereo mini x1

 

AUDIO OUT ..................................................

Stereo mini x1

 

Others

 

 

CONTROL.....................................................

D-sub9 pin x1

 

Lamp:456-8789H

 

 

Filter set: UX36761

 

Optional parts

Laser remote control: RC-R008

 

* For more information, please consult your dealer.

69

Specifications

Specifications (continued)

221

306

77 83

[unit: mm]

403-8791HW-GENERAL-00

70