Dukane 28A8800A User Manual

Size:
1.43 Mb
Download

Liquid Crystal Projector

Model

28A8800A

OPERATING GUIDE

Liquid Crystal Projector

Model

ImagePro 8800A

USER’S GUIDE

Thank you for purchasing the Dukane liquid crystal projector. Please read this user’s manual thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference.

Outline

This liquid crystal projector is used to project various computer signals as well as NTSC/PAL/SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.

Features

(1) Outstanding brightness

The UHB lamp and high-efficiencyoptical system assure a high level of brightness.

(2) Partial magnification function

Interesting parts of images can be magnified for closer viewing.

(3) Distortion correction function

Distortion-freeimages are quickly available.

(4)Power zoom and power focus.

(5)P in P function

(6)USB jack

Contents

Page

Before Use

.............................................

3

Checking the package Contents .............

8

Names and functions of each part ..........

8

Installation ..............................................

12

Basic operations ....................................

13

Adjustments and functions .....................

17

Connection to the vido signal

 

terminals ...............................

22

Connection to the RGB signal

 

terminal ...............................

22

Connecting to the USB ........................

25

Connection to the CONTROL signal

 

terminal ...............................

26

Example of system setup .....................

31

Cleaning the air filter ...........................

31

Lamp

.............................................

32

Message table ......................................

32

When you think something wrong .........

33

Specifications .......................................

34

About the warranty and

 

after-service .........................

35

Before Use

<Before Using>

About the Symbols Various symbols are used in this instruction manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents.

Warning

Caution

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to incorrect handling.

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents (the illustration to the left indicates danger of electrical shock).

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that the power plug should be disconnected from the power outlet).

3

Do not Do not use disassemble. near water.
Disconnect the plug from the power outlet.

[Safety Precaution]

Warning

If a problem should occur.

If smoke or a strange odor arise, continued use could result in fire or electrical shock. In

such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer for repairs. Never attempt to make repairs yourself because this is dangerous.

Do not use this projector if

there is no image or sound, or if the sound is distorted. Continued use

could result in fire or electrical shock.

In such case, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

If water should enter the inside of this projector, immediately turn off the power

switch, disconnect the power plug from the power outlet and contact your dealer.

Do not install on an unstable surface.

Do not install this projector on an unstable surface such as a wobbly

stand or incline because this could result in the projector falling and causing injury.

Do not open the cabinet.

Never open the cabinet.

Ther eis high voltage inside which can cause electrical shock.

Contact your dealer for

internal inspection, adjustment and repair.

Do not modify.

Do not modify this projector because Do not

this could result in fire or electrical shock.disassemble.

Do not use in the bathroom.

Do not use this projector in the

bathroom because this could result in Do not use near fire or electrical shock.water.

Do not insert foreign objects.

Do not insert metal objects through the ventilation openings, etc., of

this projector or drop such objects inside because this could result in fire or electrical shock.

If a foreign object should enter this projector, immediately turn off the power switch, disconnect the

power plug from the

power outlet and contact your dealer.

Continued use could result in

Disconnect the

plug from the

fire or electrical shock. Use

power outlet.

special caution in households

 

where children are present.

 

Do not look through the lens when the lamp is on.

Never look through the lens when the

lamp is on. The powerful light could adversely affect vision. Use special caution in households where children are present.

Avoid shock or impact on the projector.

If the projector should fall, resulting in damage to the cabinet, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer. Continued use could result in fire or electrical shock.

Disconnect the plug from the power outlet.

Do not place this projector in a container containing liquid.

Do not place flower vases, flower pots, cups, cosmetics, liquids

such as water, etc., on top of this projector.

Spillage could result in fire or electrical shock.

Use only the indicated power supply.

Use only the indicated power

supply. The use of any other power supply could result in fire or electrical shock.

4

Warning

Handle the power cord with care.

Do not damage, cut, process or strongly twist the power cord. Placing

heavy objects on the power cord, heating or strongly pulling the power cord can result in damage as well as fire or electrical shock.

Pulling on the power cord

Placing heavy objects on the power cord

Damaging the cord

Placing near heaters

Do not position the power

cord under the projector. This can damage the power cord and cause fire or electrical shock. Also, do not place a spread, cover, etc., over the power cord because this could result in the inadvertent placing of heavy objects on the concealed power cord.

If the power cord is damaged (exposed or broken core wires,

etc.), contact your dealer for replacement; otherwise, fire or electrical shock could result.

Make sure there is no dust, etc., on the power plug and insert a knife blade to make sure that

there is no looseness.

Do not allow the laser beam to enter the eyes.

This remote control is equipped with a laser pointer and a laser beam is emitted from the laser outlet. Do not look directly into the laser beam outlet or direct the laser beam at other people.

Vision can be impaired if the laser beam enters the eyes. Use special caution in households where children are

present.

High temperatures are generated when the lamp is lit, so do not place objects in front of the lens.

C A U T I O N

LASER RADIATION-

DO NOT STARE INTO BEAM

WAVE LENGTH: 650nm

MAX . OUTPUT: 1mW

CLASS 2 LASER PRODUCT

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASSE 2

RAYONNEMENT LASER

MANUFACTURED

NE PAS REGARDER DANS

 

LE FAISCEAU APPAREIL

 

A LASER DE CLASSE 2

 

LASER-STRAHLUNG

PLACE OF

NICHT IN DEN STRAHL

MANUFACTURER:A

BLICKEN LASER KLASSE2

MADE IN JAPAN

IEC60825-1:1993+A1:1997

Laser beam outlet

AVOID EXPOSURE-

LASER RADIATION IS EMITTED FROM THIS APERTURE

5

Caution

Do not sit or place heavy objects on this projector.

Do not sit on this projector.

This could result in overturning, leading to damage or personal injury. Use special caution in households where children are present.

Do not place heavy objects on this projector.

Placing heavy objects on this projector could result in loss of balance or falling and cause personal injury.

Do not block the ventilation openings.

Do not block the ventilation openings of this projector. Blocking ventilation could lead to internal overheating which could result in fire. Do not place this projector on its

side during use or push it into a small, poorly ventilated location. Do not place this projector on a carpet or bedding or cover it with a table cloth,

etc. Also, when installing this projector, make sure the ventilation openings are at least 10cm from the wall.

Care and maintenance.

For safety purposes, disconnect the power plug from the power outlet

before starting the care and maintenance of this projector.

Disconnect the plug from the power outlet.

Battery usage.

Use only the specified batteries with this projector. Do not mix old

and new batteries because this could result in fire or personal injury due to battery cracking or leakage.

Make sure the plus and minus terminals are correctly aligned

when loading the batteries.

Incorrect loading could result in personal injury or contamination of

the surroundings due to battery cracking or leakage.

Clean the projector interior once every two years.

Request your dealer to clean the interior of the projector approximately every two years. Accumulations of dust inside the projector can result in fire or

malfunction if not cleaned for an extended period. This cleaning is more effective if performed befor every humid periods such as rainy

season, etc. Ask your dealer for details about internal cleaning.

Avoid installation in humid or dusty locations.

Do not install this projector in a humid or dusty location. This could

result in fire or electrical shock.

Avoid installation near the

kitchen, a humidifier or other locations where there is oily smoke or humidity.

This could result in fire or electrical shock.

Use the caster brakes.

When installing this projector on a stand with casters, use the caster

brakes to prevent the stand moving or overturning and causing personal injury.

Do not handle the power cord roughly.

Keep the power cord away from heaters because the heat could melt the

power cord and cause fire or electrical shock.

Do not touch the power plug

with wet hands because this could result in electrical shock.

When disconnecting the

power plug, do not pull on the power cord. This could damage the power cord and cause fire or electrical shock. Always grip the plug when disconnecting.

6

Disconnect the plug from the power outlet.

Caution

When the projector is not to be used for an extended period.

For safety purposes when the projector is not to be used for an extended period because of travel, etc., always disconnect the power plug from the power outlet. Also close the lens cover to prevent the lens surface being scratched.

Disconnect the plug from the power outlet.

Moving the projector.

When moving the projector, be sure to close the lens cover, disconnect the power plug from the power outlet and disconnect all external connections. Failure to do this could damage the power cord and cause fire or electrical shock.

Avoid any impact or shock to the projector

because this could result in malfunction.

When moving this projector outdoors, protect it from wetting due to rain, etc. If the

projector should become wet, dry it thoroughly before further use. Continued use while wet could result in fire or electrical shock.

[General Cautions]

Avoid excessively hot locations.

Do not place this projector in direct sunlight or near a hot object such as a stove, etc., because the heat could have adverse influence on the cabinet and other parts.

Sound volume.

Set the volume at a suitable level to avoid bothering other people. It is also better to keep the volume level low and close the windows at night to protect the neighborhood environment.

Lens care

Use commercially available lens tissue to clean the lens (used to clean cameras, eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Cabinet care.

The cabinet is made of plastic and discoloration or paint peeling can occur if wiped with a solvent

such as benzine, thinner, etc.

Before using chemical wipes, be sure to read and observe the instructions.

Do not spray volatile substances such as insect repellent on the cabinet. Also, do not

allow long-termclose contact with rubber or vinyl products because this could result in discoloration, peeling paint, etc.

Use a soft cloth to clean the cabinet and operation panel. When excessively soiled,

dilute a neutral detergent in water, wet and wring out the cloth and afterward wipe with a dry cloth. Do not apply undiluted detergent directly to the projector.

Extended usage.

When using this projector for an extended period, stop periodically to rest the eyes to prevent eye fatigue.

7

Checking the package Contents

Make sure all of the following items are included in the package. If anything is missing, please contact your

dealer.

VIDEO

LASER

 

 

RGB

 

 

STANDBY/ON POSITION

 

 

 

RESET

 

 

MENU

 

 

 

 

FREEZE

 

 

MAGNIFY

VOLUME

 

 

 

OFF

 

 

 

 

Remote control

Projector unit

Remote control

Batteries

User’s Guide (this document)

Power Cord

3-Conductor

c

 

d

110V-US

video/Audio cable

 

220-UK,Europe

 

RGB cable

Mac adapter

Mouse cable × 3

 

 

(15-15pin M/M)

with dip switch

 

 

 

Names and functions of each part

Main unit

ZOOM button

Used to adjust the size of the image. (Refer to page 13.)

MUTE button

This button turns the sound on and off. Press once to turn the sound off; then press again to turn the sound back on.

ZOOM FOCUS

MUTE

INPUT

 

MENU

STANDBY/ON

RESET

 

 

LAMP POWER TEMP

FOCUS button

screen. (Refer to page 13.)

INPUT button

Press this button to switch the input. The input changes in the following sequence each time this button is pressed.

RGB1 RGB2VIDEO

STANDBY / ON button

Press this button to turn the power on and off. When turned off, the projector enters standby status. Refer to page 13 - 14 for details.

LAMP indicator

This indicator lights or blinks when the lamp is off. Refer to page 33 for details.

POWER indicator

This indicator lights or blinks during standby and during operation. Refer to page 33 for details.

Remote control photoreceptor

Lens

Lens cap

MENU button

Displays the image menu. Refer to page 17 - 21 for details.

RESET button

Used to reset the initial settings. Refer to page 17 for details.

TEMP indicator

This indicator lights or blinks when the internal temperature of the projector rises and when the fan malfunctions. Refer to page 33 for details.

Speaker

Speaker

Cooling fan (exhaust side)

Handle

Cooling fan

(intake side)

• Use the remote control in front of the remote control photoreceptor at a distance 8 of about 5 m or less and an angle of 30 degrees to the left or right of the center.

Names and functions of each part (continued)

Remote control photoreceptor

Main power switch

Used to turn the power on and off.

:OFF

:ON

AC IN jack

Used to connect the accessory power cord.

Caution Connecting to the AC IN jack

Make sure the accesory power cord is plugged into the AC IN jack as far as it will go. Incomplete connection can result in fire or electrical shock.

VIDEO IN jack

S-VIDEOIN jack

Mini DIN 4-pinconnector VIDEO IN jack

RCA jack AUDIO L/R IN jack RCA jack

1 RGB IN 2 S-VIDEOIN

RGB IN jack

D-sub15-pinshrink (1/2)

 

 

 

VIDEO IN

 

CONTROL

RGB OUT

CONTROL jack

 

 

AUDIO IN

 

 

L

D-sub15-pinshrink

 

 

 

 

 

 

 

 

MONO

 

 

 

R

AUDIO IN

AUDIO

 

1

2

OUT

 

 

 

 

USB

 

USB jack

AUDIO IN jack (RGB)

The mouse cursor can be controlled by

remote control by connecting to a

Stereo mini jack

personal computer.

 

AUDIO OUT jack (RGB/VIDEO)

Stereo mini jack

RGB OUT jack

D-sub15-pinshrink

9

Names and functions of each part (continued)

Remote control transmitter

VIDEO, RGB button

Press to switch the input. (Refer to page 13, 19.)

VIDEO

RGB

 

LASER

STANDBY / ON button

STANDBY/ON

POSITION

Used to turn the power on and off.

Press for 1 sec. or more to turn the power off (enter standby status).

(Refer to pages13 and 14.)

DISK PAD **

(1)Used to select menu items when the menu screen is displayed (refer to page 16 - 18).

(2)When the menu is not displayed, the mouse shift function and left click function are active.

*1 (3) After the POSITION button has been pressed, the screen can be moved upward, downward and to the left and right.

RESET

MENU

FREEZE

MAGNIFY VOLUME

OFF

LASER button

Turns the laser beam on and off. Refer to page 11 cocnerning usage and observe the cautions.

POSITION button**

Pressing the top, bottom, left or right of Disk Pad after pressing this button causes corresponding movement (Effective only during RGB signal selection).

RESET MOUSE / RIGHT button**

(1)Operates as the RESET button when the menu is displayed. Press this button to return to the initial settings.

(2)Used to click the right mouse button when the menu is not displayed (refer to page 25,26).

*1 (3)Pressing this button after scrolling the screen with POSITION returns the screen to the original position.

MENU button**

Used to turn the menu screen display on and off.

(refer to page 17 - 21).

MAGNIFY button**

Used to magnify the displayed image.

P in P button**2

Used to turn P in P (Picture In Picture: displays sub video signal images in the RGB signal) on and off.

Each time this button is pressed, operation will change in the following sequence:

(1) Reduce sub screen(2) Magnify sub screen(3)Off.

(1) (3)

P in P

MUTE

BLANK AUTO TIMER

FOCUS ZOOM

BLANK button

Used to turn blanking on and off. (Refer to page 20.)

FOCUS button

Used to adjust the focus of the image on the screen. (Refer to page 13.)

**These functions do not operate when initial screen message

"No Input is detected" or " Sync is out of range"is displayed

FREEZE button**

Used to turn the freeze (still) image display on and off.

VOLUME button

Adjusts the volume of the sound. Press [ ] to increase the volume and ( ) to decrease the volume. When there is no video signal input, operation is not possible when the input video signal is outside the sync range.

MUTE button**

Applies Mute. (Press the Play button again to cancel.)

TIMER button

Turns the display of the time set with the Timer on the Menu screen on and off.

Timer is not displayed during blanking, when there is no video signal input and when the video signal input is outside the sync range.

Refer to page 20, 21 concerning the method used to set the timer.

ZOOM button

Used to adjust the size of the image. (Refer to page 13.)

AUTO button**

Used to execute auto-adjust.*3

*1 POSITION icon

*3 Auto adjustment function

When the POSITION button is pressed, the remote control buttons will light and the moving display icon will appear at the bottom right of the screen.

While displaying the icon, you can operate POSITION.

*2

With the P in P function, signals are input to both RGB and VIDEO. This function operates only when the RGB signal has been selected. There is no display in the case of the no signal and when the RGB signal is outside the sync range.

When P in P is used, audio is automatically switched to video.

In P in P, audio input can be switched by pressing the VOL and VOLkeys of the remote control, displaying the audio bar and moving Disk Pad left and right during the display.

10

 

 

R G B / V I D E O

 

 

 

The projector automatically adjusts 4 items (V. POSIT, H. POSIT, H. PHASE, H. SIZE).

When you choose AUTO (move the cursor to the right from the manual operation position), the AUTO confirmation menu shown below is indicated.

Caution • Auto adjust requires several tens of seconds.

Auto adjust may not operate correctly in some cases, depending on the computer connected and the signal.

Auto adjust may not operate correctly in some cases, depending on the type of image.

Execute auto adjust with the display of the application being run by the computer at maximum.

After auto adjust, the image may be slightly dark in some cases due to automatic adjustment of the signal level.

Auto adjust canot execute when the initial display is RANGE" during FREEZE or MAGNIFY.

Names and functions of each part (continued)

Loading the batteries Loading AA batteries into the remote control.

1 Remove the battery

cover.

Push the knob while lifting up the battery cover.

Caution Battery usage cautions

Use only the specified batteries with this projector. Also, do not mix new and old batteries. This could cause in battery cracking or leakage, which could result in fire or personal injury.

When loading the batteries, make sure the plus and minus poles are correctly oriented as indicated in the projector. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment.

2 Loading the batteries.

Make sure the plus and minus poles are correctly oriented.

3 Close the battery cover.

Caution Remote control usage cautions

Do not drop the remote control or apply impact.

Do not wet the remote control or place it on any wet object. Such actions could result in

malfunction.

When not to be used for an extended period, remove the batteries from the remote control.

Replace the batteries when remote control operation becomes difficult.

Do not place the remote control close to the cooling fan of the projector.

Do not disassemble the remote control in case of malfunction. please bring it to the service station.

Warning The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people.

The laser beam can cause vision problems.

C AU T I O N

LASER RADIATION-

DO NOT STARE INTO BEAM

WAVE LENGTH: 650nm

MAX . OUTPUT: 1mW

CLASS 2 LASER PRODUCT

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASSE 2

RAYONNEMENT LASER

MANUFACTURED

NE PAS REGARDER DANS

 

LE FAISCEAU APPAREIL

 

A LASER DE CLASSE 2

 

LASER-STRAHLUNG

PLACE OF

NICHT IN DEN STRAHL

MANUFACTURER:A

BLICKEN LASER KLASSE2

y y MADE IN JAPAN

IEC60825-1:1993+A1:1997

AVOID EXPOSURE-

LASER RADIATION IS

EMITTED FROM THIS

APERTURE

11

Installation

Typical LCD Projector and Screen Installation

Use the diagram below as reference to determine the screen size and projection distnace.

Top view

Side view

Screen

Lens center

b

a

Screen size (inches)

a (inches)a

b (inches)

 

 

Minimum

Maximum

 

 

 

 

 

 

40

55

73

1

 

 

 

 

60

85

114

2

 

 

 

 

80

114

151

2

 

 

 

 

100

144

191

3

 

 

 

 

120

176

231

3

 

 

 

 

150

220

282

4

 

 

 

 

200

291

386

6

 

 

 

 

a.Distance from the LCD projector to the screen

b.Distance from the lens center to the bottom of the screen (a,b : +/-10%).

Caution

The LCD projector should normally be used level (the legs can point upward).

Positioning the projector sideways, or with the lens pointing upward or downward can cause the internal temperature to rise, which could result in a malfunction.

The projection distances shown in the diagram to the left are for full size (1024 x 768 dots.)

Using the adjusters

 

Use the adjusters on the bottom to adjust the projection angle.

 

Front view

Side view

 

Adjuster

Variable within the range of approximately 0° - 9°

1.Lift up the projector and release the adjuster lock.

2.After adjusting the projection angle, firmly lock the adjusters.

3.Rotate the adjusters for fine adjustment.

Caution • Do not release the locks unless the projector is being held; otherwise, the projector could overturn or the fingers could get caught and cause personal injury.

Do not force the adjusters to rotate. This could damage the adjusters or cause the lock to fail.

Lock the adjusters firmly. If the lock is difficult to operate, change the angle slightly and try again.

12

Basic operations

To project

2

5 7 4 2

5

1

3

VIDEO

RGB

LASER

STANDBY/ON POSITION

RESET

MENU

FREEZE

MAGNIFY VOLUME

OFF

P in P

MUTE

BLANK AUTO TIMER

FOCUS ZOOM

7

4

1

Turn on the main power switch of the projector [ I: ON].

• The Power indicator lights orange.

 

 

 

 

 

 

 

 

2

Press the STANDBY / ON button.

 

 

• The Power indicator will blink green and then light green.

 

 

 

 

• The green blinking indicates warmup.

 

 

 

 

• After the power is turned on, the lamp will be cooled for approximately 1 min. and the power cannot

 

 

be turned on even by pressing the STANDBY/ON button.

 

 

 

 

 

 

 

 

3

Remove the lens cap.

 

 

 

 

 

 

 

4

Use the ZOOM button to adjust the screen size.

 

 

 

 

 

 

 

5

Use the FOCUS button to adjust the focus.

 

 

 

 

 

 

 

 

(1) The display shown to the right will appear when the FOCUS button is pressed.

 

+++FOCUS+++

 

 

 

(2) Use the FOCUS button to adjust the focus until the image is sharp.

 

 

 

 

 

(3) The message “Focus” will disappear if any other button is pressed.

 

 

 

 

 

 

 

 

 

 

• (When there is no input signal, the Focus characters are not displayed when the input signal is outside the sync range.)

 

 

 

 

 

 

6

Turn on the power to the connected equipment.

 

 

Refer to page 31 concerning the connection of other equipment.

 

 

7 Press either the INPUT button of the projector or the VIDEO/RGB button of the remote control to select the signal to be projected on the screen.

Example on-screendisplay

RGB 1

The selected signal input channel will be displayed in the lower right part of the screen.

13

Basic operations (continued)

Turning off the power

1

1

VIDEO

RGB

LASER

STANDBY/ON POSITION

 

 

RESET

 

MENU

 

2

 

FREEZE

MAGNIFY

VOLUME

 

3

 

OFF

P in P

MUTE

 

 

BLANK

AUTO TIMER

1

Press the STANDBY/ON button for approximately 1 sec.

• The Power indicator will blink orange, then the lamp will turn off. Approximately 1 sec. after that, the

 

lamp will light orange.

 

• After the power is turned off, the lamp will be cooled for approximately 1 min. and the power cannot

 

be turned off even by pressing the STANDBY/ON button.

 

• The standby status will not be entered if the time which the STANDBY/ON button is pressed is too

 

short.

 

 

2

Turn off the main power switch of the projector [ : OFF].

3

Attach the lens cap.

Caution The fan will continue running for approximately 1 min. after the STANDBY/ON button is pressed. Do not turn off the main power switch while the lamp is on because this will shorten the service life of the lamp.

Plug & Play

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible.

(Plug & play is a system configured with peripheral equipment including a computer and display, and an operating system.

Caution Use the RGB cable included with this projector when using plug & play. With other cables, pins (12) - (15) are sometimes not connected (effective only for RGB).

14

Basic operations (continued)

Freeze function

This function is used to freeze the image being displayed. (refer to page 10)

VIDEO

RGB

LASER

STANDBY/ON POSITION

 

RESET

MENU

 

 

FREEZE

MAGNIFY

VOLUME

1

OFF

P in P

MUTE

BLANK

AUTO TIMER

1 Press the FREEZE button.

The image being displayed will freeze.

The [ ] mark appears in the lower right corner of the screen when the Freeze function is on.

Cancelling the FREEZE function

1 Press the FREEZE button.

The FREEZE function will be cancelled.

The [ ] mark will be displayed for approximately 3 sec. when the FREEZE function is cancelled.

Caution • When there is no input signal, the Freeze function is not effective when the input signal is outside the sync range.

Pressing the FREEZE button alternately turns the freeze function on and off.

The FREEZE function will be cancelled when the input select button is pressed or the display mode of the PC being used for display is changed.

When a still image signal is input when the FREEZE function is on, make sure not to for get to cancel the FREEZE function.

FREEZE function will be cancelled after the operations such as: •"menu display ON" •"FOCUS", •"MAGNIFY", •"P IN P", •"AUTO", •"VOLUME ", •"MUTE" AND POSITION

15

Basic operations (continued)

Magnify function

VIDEO

RGB

 

LASER

 

STANDBY/ON

POSITION

Part of an image can be displayed magnified. (refer to page 10)

5

 

 

RESET

1,2

MENU

 

 

FREEZE

3

MAGNIFY

VOLUME

 

OFF

 

 

 

P in P

MUTE

 

BLANK

AUTO TIMER

1 Press the MAGNIFY+ button.

• The center part of the image will be displayed magnified approximately two times.

Changing the magnification ratio

2 Press the MAGNIFY+ button.

• When this button is pressed, the image will be displayed even larger.

4

6

3 Press the MAGNIFYbutton.

• When this button is pressed, the image will be displayed even smaller.

Moving the display area

4

Press the POSITION button.

5

Press the DISK PAD up, down, left and right buttons.

 

• The magnified area will move in accordance with the button pressed.

Returning to normal display

6 Press the MAGNIFY OFF button.

Caution • When there is no video signal input, Magnify is not effective when the video signal input is outside the sync range.

The magnify function will be cancelled when the input select button is pressed or the display mode of the PC being used for display is changed.

The Magnify function will be cancelled after the operations such as"menu display ON",

"FOCUS","FREEZE","P in P","AUTO","VOLUME","MUTE" and

"POSITION".

16

Adjustments and functions

1, 2, 3

VIDEO

RGB

LASER

STANDBY/ON

POSITION

RESET

MENU

FREEZE

MAGNIFY VOLUME

OFF

MENU

P in P MUTE

1

BLANK AUTO

TIMER

 

FOCUS

ZOOM

1, 3

2, 3

3

1

Press the MENU (

) buttons of the projector or the

 

MENU button of the remote control.

• The Menu screen will appear. (refer to page 18 - 21 for details.)

2 Press the MENU () buttons of the projector or the DISK PAD button of the remote control to select the menu item to be adjusted.

• The selected menu item will be displayed in orange.

3 Adjust the selected menu item with the MENU () buttons of the projector or DISK PAD button of the remote control.

The selected menu item will be displayed in orange. The menu will disappear after 5-10sec.

Returning to the initial settings

Select the adjustment item to be returned to the initial settings.

Press the RESET button.

17

Adjustments and functions (continued)

SET UP

Images and display positions can be adjusted from the SETUP menu.

RGB signal input

S E T U P I N P U T I M A G E

O P T.

VOLUME

 

 

BRIGHT

 

 

CONTRAST

 

 

V POSIT

100

 

H POSIT

100

 

H PHASE

 

 

H SIZE

800

 

COLOR BAL R

 

 

COLOR BAL B

 

 

Video signal input

S E T U P I N P U T I M A G E

O P T.

VOLUME

 

BRIGHT

 

CONTRAST

 

SHARPNESS

 

COLOR

 

TINT

 

COLOR BAL R

 

COLOR BAL B

 

Adjustment item

Adjustment description

 

 

 

 

VOLUME

Volume decreases

 

Volume increases

 

 

 

 

 

BRIGHT

Darker

 

Brighter

(BRIGHTNESS)

 

 

 

 

 

 

 

 

CONTRAST

Lower contrast

 

Stronger contrast

 

 

 

 

 

SHARPNESS

Softer image

 

Sharper image

 

 

 

 

 

COLOR

Less

 

More

 

 

 

 

 

TINT

Redder

 

Greener

 

 

 

 

 

V. POSIT

Moves the image up and down.

(V. POSITION)

 

 

 

 

 

 

 

H. POSIT

Moves the image left and right.

(H. POSITION)

 

 

 

 

 

H. PHASE

Eliminates blanking.

 

 

H. SIZE

Adjusts the horizontal size of the image.

 

 

 

 

COLOR BAL R

Less Red

 

More Red

(COLOR BALANCE Red)

 

 

 

 

 

 

 

 

COLOR BAL B

Less Blue

 

More Blue

(COLOR BALANCE Blue)

 

 

 

 

 

 

 

 

Using the SETUP Menu

Move the cursor to the item to be adjusted and move the MENU button of the projector or the DISK PA button of the remote control to change the length of the bar display.

Caution • The menu cannot be displayed while the initial screen (“No input is detected.” or “Sync is out of range.”) is being displayed.

Tint cannot be adjusted with PAL or SECAM video signal input.

Tint, color and sharpness cannot be adjusted with RGB signal input.

V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with video signal input.

The MAGNIFY or FREEZE function will be cancelled after the operation "Menu".

Displaying the menu cancels magnify and freeze operations.

18

Adjustments and functions (continued)

INPUT

The INPUT menu is used to select RGB signal sync signal frequency of the monitor and the VIDEO signal.

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

 

 

RGB

fH:38kHz

RGB

AUTO

VIDEO

VIDEO

 

NTSC

fV:60Hz

 

 

 

PAL

 

 

 

 

 

 

SECAM

 

 

 

NTSC4.43

 

 

 

M-PAL

 

 

 

N-PAL

Adjustment item

Adjustment description

 

 

 

Displays the following RGB inputs

RGB

fH: horizontal sync frequency

 

fV: vertical sync frequency

 

 

VIDEO

Sets the video signal system. When the screen is unstble (no color)

or rolls, select the mode that matches the input signal.

 

 

 

19

Adjustments and functions (continued)

IMAGE

Projection image inversion, etc., can be selected from the IMAGE menu.

S E T U P I N P U T I M A G E O P T .

KEYSTONE

MIRROR

BLANK

START UP

P. IN P.

S E T U P I N P U T I M A G E O P T .

KEYSTONE

MIRROR

BLANK

START UP

P. IN P.

S E T U P I N P U T I M A G E O P T .

KEYSTONE

 

MIRROR

 

BLANK

WHITE

START UP

BLUE

P. IN P.

BLACK

S E T U P I N P U T I M A G E O P T .

KEYSTONE

MIRROR

BLANK

START UP

P. IN P.

S E T U P I N P U T I M A G E O P T .

KEYSTONE

 

MIRROR

NORMAL

BLANK

H : INVERT

START UP

V : INVERT

P. IN P.

H&V :

 

INVERT

S E T U P I N P U T I M A G E O P T .

KEYSTONE

 

MIRROR

 

BLANK

 

START UP

TURN ON

P. IN P.

TURN OFF

Adjustment item

Adjustment description

 

 

 

 

 

KEYSTONE

Reduces keystone

 

 

Reduces keystone

distortion at the bottom

distortion at the top

 

 

 

 

 

 

Sets vertical or horizontal inversion of the projected image.

MIRROR

H: horizontal inversion only

 

V: vertical inversion only

 

 

 

 

H&V: both horizontal and vertical inversion.

 

 

 

 

 

BLANK

Sets the color to be used for blanking with BLANK ON or when there is no signal.

Blanking is turned on when there is no signal for approximately 5 min.

 

 

 

 

 

START UP

Opens and closes the initial settings screen during signal input at start up.

 

 

 

 

 

P in P

Selects the P in P sub screen display position.

 

 

 

 

 

 

20

Adjustments and functions (continued)

OPT

Communication functions, etc., can be set from the OPT menu.

S E T U P I N P U T I M A G E O P T .

COM. SPEED

COM. BITS

TIMER

LANGUAGE

AUTO OFF

SYNC ON G

S E T U P I N P U T I M A G E O P T .

COM. SPEED

1200bps

COM. BITS

2400bps

TIMER

4800bps

LANGUAGE

9600bps

AUTO OFF

19200bps

SYNC ON G

 

S E T U P I N P U T I M A G E O P T .

COM. SPEED

 

COM. BITS

 

TIMER

 

LANGUAGE

10 min.

AUTO OFF

 

SYNC ON G

 

S E T U P I N P U T I M A G E O P T .

COM. SPEED

 

COM. BITS

 

TIMER

 

LANGUAGE

 

AUTO OFF

 

SYNC ON G

10 min.

S E T U P I N P U T I M A G E O P T .

COM. SPEED

 

COM. BITS

7N1

TIMER

8N1

LANGUAGE

 

AUTO OFF

 

SYNC ON G

 

S E T U P I N P U T I M A G E O P T .

COM. SPEED

ENGLISH

COM. BITS

FRANÇAIS

TIMER

DEUTSCH

ESPAÑOL

LANGUAGE

ITALIANO

AUTO OFF

NORSK

SYNC ON G

NEDERLANDS

 

 

JAPANESE

S E T U P I N P U T I M A G E O P T .

COM. SPEED

 

COM. BITS

 

TIMER

 

LANGUAGE

 

AUTO OFF

 

SYNC ON G

TURN ON

 

TURN OFF

Adjustment item

Adjustment description

 

 

COM. SPEED

Sets the communication speed (5 steps).

 

 

COM. BITS

Sets the bit configuration for the communication data.

7N1...7 data bits, No parity, 1 stop bit.

 

8N1...8 data bits, No parity, 1 stop bit.

 

 

TIMER

Sets the timer display time (0 - 99) min.

 

 

LANGUAGE

Selects the menu screen language

(English, French, German, Spanish, Italian, Norwegian, Dutch, Japanese).

 

 

 

AUTO OFF

Sets the time after which the power will be turned off (standby status) when

there is no input signal. The settings are 1 - 99 min, 0 and None.

 

 

 

SYNC ON G

Sets the SYNC ON G feature on/off.

 

 

21

Connection to the video signal terminals

1. Input signals

S-VIDEOsignal

Brightness signal

1.0V p-p,75Ω terminator

Color signal

0.286V p-p(burst signal), 75Ω terminator

 

 

 

 

 

 

VIDEO signal

 

1.0V p-p,75Ω terminator

 

 

 

 

Audio signal

Input

 

200mV rms, 20k Ω or less (max. 3.0Vp-p)

 

 

 

Output

 

0 200mVrms,1k Ω

 

 

 

 

 

 

2. Signal input jacks

Color signal Brightness signal

Ground

Ground

 

 

S-VIDEOinput (mini DIN4-pin)

 

 

Caution

The priority sequence of the video input jacks is as follows.

 

(1) S-VIDEOinput jack

(2) RCA jack input jack

When video signals are being projected, the audio input by the video is output to the audio output jack (RGB/VIDEO).

Connection to the RGB signal terminal

1. Input signals

Video signal

Analog, 0.7V p-p,75Ω terminator (positive polarity)

Horizontal sync signal

TTL level (positive/negative polarity)

Vertical sync signal

TTL level (positive/negative polarity)

Compound sync signal

TTL level

Audio signal

 

Input

200mV rms, 20k Ω or less (max. 3.0Vp-p)

 

 

 

0~200mVrms,1k Ω

 

 

 

Output

 

 

 

 

 

2. Signal input jacks

 

 

1

Video input (red)

9

N.C

2

Video input (green)

10

Ground

3

Video input (blue)

11

N.C

4

N.C

12

DDC jack (Display Data Channel)

5

N.C

13

Horizontal sync signal/compound sync signal

6

Ground (red)

14

Vertical sync signal

7

Ground (green)

15

DDC jack (Display Data Channel)

D-sub15-pinshrink jack

8 Ground (blue)

22

Connection to the RGB signal terminal (continued)

3. Example of computer signal

Resolution

fH

fV

Rating

Signal mode

Display mode

Note 1

H × V

(kHz)

(Hz)

 

 

 

 

 

 

 

 

 

 

 

 

640

× 400

24.8

56.4

 

NEC PC9800

Zoom in

 

 

 

 

 

 

 

 

 

640

× 350

37.9

85.1

VESA

VGA-1

Zoom in

 

 

 

 

 

 

 

 

 

640

× 400

37.9

85.1

VESA

VGA-2

Zoom in

 

 

 

 

 

 

 

 

 

720

× 400

37.9

85.0

VESA

TEXT

Zoom in

 

 

 

 

 

 

 

 

 

640

× 480

31.5

59.9

VESA

VGA-3

Zoom in

 

 

 

 

 

 

 

 

 

640

× 480

35.0

66.7

 

Mac13"mode

Zoom in

SW 1 ON

 

SW 2 ON

 

 

 

 

 

 

 

640

× 480

37.9

72.8

VESA

VGA-3(72Hz)

Zoom in

 

 

 

 

 

 

 

 

 

640

× 480

37.5

75.0

VESA

VGA-3(75Hz)

Zoom in

 

 

 

 

 

 

 

 

 

640

× 480

43.3

85.0

VESA

VGA-3(85Hz)

Zoom in

 

 

 

 

 

 

 

 

 

800

× 600

35.2

56.3

VESA

SVGA(56Hz)

 

 

 

 

 

 

 

 

 

 

800

× 600

37.9

60.3

VESA

SVGA(60Hz)

 

 

 

 

 

 

 

 

 

 

800

× 600

48.1

72.2

VESA

SVGA(72Hz)

 

 

 

 

 

 

 

 

 

 

800

× 600

46.9

75.0

VESA

SVGA(75Hz)

 

 

 

 

 

 

 

 

 

 

800

× 600

53.7

85.1

VESA

SVGA(85Hz)

 

 

 

 

 

 

 

 

 

 

832

× 624

49.7

74.5

 

Mac16"mode

Zoom in

SW 2 ON

 

SW 4 ON

 

 

 

 

 

 

 

1024 × 768

48.4

60.0

VESA

XGA(60Hz)

Zoom out

 

 

 

 

 

 

 

 

1024 × 768

56.5

70.1

VESA

XGA(70Hz)

Zoom out

 

 

 

 

 

 

 

 

1024 × 768

60.0

75.0

VESA

XGA(75Hz)

Zoom out

 

 

 

 

 

 

 

 

1152 × 768

67.5

75.0

VESA

SXGA(75Hz)

Zoom out

 

 

 

 

 

 

 

 

1280 × 960

60.0

60.0

VESA

SXGA(60Hz)

Zoom out

 

 

 

 

 

 

 

 

 

1280

× 1024

64.0

60.0

VESA

SXGA(60Hz)

Zoom out

 

 

 

 

 

 

 

 

 

1280

× 1024

80.0

75.0

VESA

SXGA(75Hz)

Zoom out

 

 

 

 

 

 

 

 

 

Note 1: Mac adapter is necessary to the resolution mode.

Projector is compatible with 13 inch mode and 16 inch mode. Mac 13" mode=switch 1 and switch 2 are ON.

Mac 16" mode=switch 2 and switch 4 are ON.

ON

 

 

 

 

 

1

2

3

4

5

6

OFF

 

 

 

 

 

(Example 16 inch mode)

Caution • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer.

Depending on the input signal, full-sizedisplay may not be possible in some cases. Refer to the number of display pixels above.

23

Connection to the RGB signal terminal (continued)

4. Initial set signals

The following signals are used for the initial settings.

The signal timing of some computer models may be different. In such case, refer to pages 17 and 18 and adjust the V.POSIT and H.POSIT of the menu.

Back porch bb

 

 

 

 

 

Front porch d d

 

 

 

 

 

Display interval c

 

 

 

 

 

 

c

 

 

 

 

 

 

 

 

 

 

 

 

 

DATA

HSYNC

Syncaa

Computer/Signal

Horizontal signal timing (µs)

 

Computer/Signal

Horizontal signal timing (µs)

 

 

 

 

 

 

 

 

 

a

b

c

d

a

b

c

d

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VGA-1(85Hz)

2.0

3.0

20.3

1.0

 

SVGA (72Hz)

2.4

1.3

16.0

1.1

 

 

 

 

 

 

 

 

 

 

 

VGA-2(85Hz)

2.0

3.0

20.3

1.0

 

SVGA (75Hz)

1.6

3.2

16.2

0.3

 

 

 

 

 

 

 

 

 

 

 

PC-9800

3.0

3.8

30.4

3.0

 

SVGA (85Hz)

1.1

2.7

14.2

0.6

 

 

 

 

 

 

 

 

 

 

 

TEXT

2.0

3.0

20.3

1.0

 

Mac 16"mode

1.1

3.9

14.5

0.6

 

 

 

 

 

 

 

 

 

 

 

VGA-3

3.8

1.9

25.4

0.6

 

XGA (60Hz)

2.1

2.5

15.8

0.4

 

 

 

 

 

 

 

 

 

 

 

Mac 13"mode

2.1

3.2

21.2

2.1

 

XGA (70Hz)

1.8

1.9

13.7

0.3

VGA-3(72Hz)

1.3

3.8

20.3

1.0

 

XGA (75Hz)

1.2

2.2

13.0

0.2

VGA-3(75Hz)

2.0

3.8

20.3

0.5

 

SXGA (1152 X 864, 75Hz)

1.2

2.4

10.7

0.6

 

 

 

 

 

 

 

 

 

 

 

VGA-3(85Hz)

1.6

2.2

17.8

1.6

 

SXGA (1280 X 960, 60Hz)

1.0

2.9

11.9

0.9

 

 

 

 

 

 

 

 

 

 

 

SVGA(56Hz)

2.0

3.6

22.2

0.7

 

SXGA (1280 X 1024, 60Hz)

1.0

2.9

11.9

0.9

 

 

 

 

 

 

 

 

 

 

 

SVGA(60Hz)

3.2

2.2

20.0

1.0

 

SXGA (1280 X 1024, 75Hz)

1.1

1.8

9.5

0.1

 

 

 

 

 

 

 

 

 

 

 

Back porch b b

 

Front porch d d

Displayc interval c

DATA

VSYNC

Syncaa

Computer/Signal

Vertical signal timimg (lines)

 

 

 

 

a

b

c

d

 

 

 

 

 

 

VGA-1(85Hz)

3

60

350

32

 

 

 

 

 

VGA-2(85Hz)

3

41

400

1

 

 

 

 

 

PC-9800

8

25

400

7

 

 

 

 

 

TEXT

3

42

480

1

 

 

 

 

 

VGA-3

2

33

480

10

 

 

 

 

 

Mac 13"mode

3

39

480

3

 

 

 

 

 

VGA-3(72Hz)

3

28

480

9

 

 

 

 

 

VGA-3(75Hz)

3

16

480

1

 

 

 

 

 

VGA-3(85Hz)

3

25

480

1

 

 

 

 

 

SVGA (56Hz)

2

22

600

1

 

 

 

 

 

SVGA (60Hz)

4

23

600

1

 

 

 

 

 

Computer/Signal

Vertical signal timimg (lines)

 

 

 

 

a

b

c

d

 

 

 

 

 

 

SVGA (72Hz)

6

23

600

37

 

 

 

 

 

SVGA (75Hz)

3

21

600

1

 

 

 

 

 

SVGA (85Hz)

3

27

600

1

 

 

 

 

 

Mac 16"mode

3

39

624

1

 

 

 

 

 

XGA (60Hz)

6

29

768

3

 

 

 

 

 

XGA (70Hz)

6

29

768

3

 

 

 

 

 

XGA (75Hz)

3

28

768

1

 

 

 

 

 

SXGA (1152 X 864, 75Hz)

3

32

864

1

 

 

 

 

 

SXGA (1280 X 960, 60Hz)

3

36

960

1

 

 

 

 

 

SXGA (1280 X 1024, 60Hz)

3

38

1024

1

 

 

 

 

 

SXGA (1280 X 1024, 75Hz)

3

38

1024

1

 

 

 

 

 

24

Connecting the USB

1.Connect the projector and computer with a suitable commercially available cable.

2.Press the INPUT button of the projector or the RGB 1/2 button of the remote control and select the input where the computer is to be connected.

3.Start the mouse function.

4.Refer to page 10, 26 concerning the remote control of mouse operations.

5.Varying the force with which the DISK PAD button is pressed varies the speed of mouse operation.

USB jack

Projector

Computer

 

 

 

USB jack

 

 

 

 

 

(B type)

 

 

 

 

 

 

 

 

 

 

 

(A type)

 

 

 

 

 

2

1

+5V

1

 

 

1

+5V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–DATA

2

 

 

2

–DATA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+DATA

3

 

 

3

+DATA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

4

GND 4

 

 

4

GND

1

 

2

 

3

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB cable

Caution • Before making connections, read the instruction manual of the equipment to be connected.

Use the optional USB cable to connect.

Effective with USB only when the mouse is used.

Do not use with any device other than a personal computer.

When using with Windows 95, it is necessary to set so that USB can be used with version OSR 2.1 or higher. Depending on the kind or the version of the host controller,

operation may not be possible in some cases.

In the case of notebook type computers with a built-inpointing device such as a track ball, in some cases thebuilt-inpointing device will have priority even if a mouse is connected and the mouse may not be selected.

In such case, disable the built-inpointing device and change the BIOS setting (system setup) so that an external mouse can be selected.

After changing the BIOS setting, perform the operations described in 1 - 3 above. Refer to the computer hardware manual concerning the BIOS setting.

Also, some computers may not have a utility program to operate a mouse. Refer to the computer hardware manual.

25

Connection to the control signal terminal

1.Mouse functions

(1)Turn off the main power switches of the projector and computer and connect the two units with the cable provided or an optional suitable commercially available cable. Disconnect the USB cable from the projector.

(2)Turn on the main switch of the projector (the ON indicator lamp will light green).

(3)Press the INPUT button of the projector or the RGB button of the remote control and select the input where the computer is to be connected.

(4)Turn on the computer power supply.

(5)Start the mouse function.

If the mouse has not been started, reboot the computer (soft reboot or reboot buttons).

(6)Refer to page 10 concerning remote control operation.

(7)Varying the force with which the DISK PAD button is pressed varies the speed of mouse operation.

PS/2 Mouse

Projector

Computer

Mouse jack Mini

 

 

1

1

DATA

DIN 6-pin

 

 

 

 

 

CLK 2

2

 

 

 

control jack

DATA 3

3

GND

6

5

D-sub15-pinshrink jack

 

4

4

+5V

 

4

3

 

 

5

5

CLK

 

SEL0

6

6

 

2

1

 

RTS

7

 

 

 

 

 

 

 

 

 

8

 

 

 

 

+5V 9

 

GND 10

 

11

 

12

 

13

 

14

Mouse cable (PS/2)

15

 

Use the mouse cable provided or a PS/2 mouse cable (for IBM and compatibles).

Cables for ADB mouse (Apple), bus mouse (NEC) and serial mouse are available as options.

Mouse cable

Product name

Model

 

 

 

ADB mouse

COE-MAC(ADB)-2

SC-MA201XC

 

 

 

Bus mouse

COE-PC98(BUS)-2

SC-MN201XC

 

 

 

Serial mouse

COE-SERIAL-2

SC-MS201XC

 

 

 

Caution • Before making connections, read the instruction manual of the equipment to be connected.

• Turn off the projector and computer power supplies before connecting.

Connecting the mouse cable with the computer power on can result in a malfunction. Use the mouse cable provided or an optional mouse cable to make the connection.

In the case of notebook type computers with a built-inpointing device such as a track ball, in some cases thebuilt-inpointing device will have priority even if a mouse is connected and

the mouse may not be selected.

In such case, disable the built-inpointing device and change the BIOS setting (system setup) so that an external mouse can be selected.

After changing the BIOS setting, perform the operations described in (1) - (3) above. Refer to the computer hardware manual concerning the BIOS setting.

Also, some computers may not have a utility program to operate a mouse. Refer to the computer hardware manual.

26

Connection to the control signal terminal (continued)

CONTROL signal jack

 

 

 

 

 

 

ADB (Mac) mouse

 

 

 

 

 

 

 

 

 

 

 

Mouse

 

 

 

 

 

 

 

 

 

Pin no.

RS-232C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PS/2

ADB

Serial

BUS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Projector

Computer

Mouse

jack

 

1

 

 

 

 

YB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mini DIN 4-pin

 

2

 

CLK

 

 

 

1

 

 

 

 

 

 

1 ADB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

DATA

DATA

 

 

2

 

 

 

 

 

 

2 (POWER ON)

 

 

 

 

 

 

 

 

 

 

 

DATA 3

 

 

 

 

 

 

3 +5V

 

 

 

 

 

4

 

 

 

 

XA

 

 

 

 

 

 

4

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

4 GND

 

 

5

 

 

 

 

XB

5

 

 

 

 

 

 

 

2

 

1

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

6

SELO

SELO

 

SELO

SELO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RTS 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

RTS

RTS

RTS

RTS

RTS

8

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

YA

+5V 9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND 10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

+5V

+5V

 

+5V

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

GND

GND

GND

GND

GND

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

SW-L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

SEL-1

15 Mouse cable (ADB) (option)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

RD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

TD

 

 

TD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

SW-R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Serial mouse

Projector

Computer

 

Mouse jack

 

1

1

CD

 

 

 

D-sub9-pin

 

2

2

RD

 

 

 

 

 

 

 

3

3

TD

1

2

3

4

5

4

4

DTR

 

 

 

 

 

5

5

GND

 

6

7

8

9

SELO 6

6

DSR

 

 

 

 

 

RTS 7

7

RTS

 

 

 

 

 

8

8

CTS

 

 

 

 

 

9

9

RI

 

 

 

 

 

GND 10

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

TD 14

Mouse cable (serial) (option)

 

 

 

15

 

 

 

27

Connection to the control signal terminal (continued)

2.RS232C communication

(1)Turn off the projector and computer power supplies and connect with the RS232C cable.

(2)Turn on the computer power supply and, after the computer has started up, turn on the projector power supply.

(3)Refer to page 20, 21 and set the communication speed and the number of communication bits.

(4)Start RS232C communication.

 

 

Projector

 

Computer

 

RS232C jack

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

1 CD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D-sub9-pin

 

 

 

Control jack

 

2

 

 

 

 

 

 

 

 

 

 

 

2 RD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

3

TD

1

2

3

 

4

5

 

 

D-sub15-pinshrink

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

4 DTR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

5 GND

 

6

7

8

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SELO 6

 

 

 

 

 

 

 

 

 

 

 

6 DSR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RTS 7

 

 

 

 

 

 

 

 

 

 

 

7 RTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

8 DTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

9 RI

 

 

 

 

 

 

 

 

 

GND 10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

RS232C cable

 

 

 

 

 

 

RD 13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TD 14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Projectorcomputer

 

 

 

 

 

 

 

 

Computerprojector

 

 

 

 

 

 

 

 

 

Command

Response code

 

Inquiry code

 

Setting code

 

Default setting code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1st

2nd

data

 

 

1st

2nd

 

1st

2nd

data

 

1st

2nd

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUSE

11h

05h

+1

 

 

 

20h

05h

 

31h

05h

+1

 

40h

05h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMMUNICATE

11h

06h

+1

 

 

 

20h

06h

 

31h

06h

+1

 

40h

06h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

11h

11h

+1

 

 

 

20h

11h

 

31h

11h

+1

 

––––––

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZOOM

11h

12h

+1

 

 

 

 

––––––

 

31h

12h

+1

 

––––––

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOCUS

11h

13h

+1

 

 

 

 

––––––

 

31h

13h

+1

 

––––––

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MIRROR

11h

14h

+1

 

 

 

20h

14h

 

31h

14h

+1

 

40h

14h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT

11h

21h

+1

 

 

 

20h

21h

 

31h

21h

+1

 

40h

21h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(VIDEO)SYSTEM

12h

22h

+2

 

 

 

20h

22h

 

32h

22h

+2

 

40h

22h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOLUME

11h

23h

+1

 

 

 

20h

23h

 

31h

23h

+1

 

40h

23h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MUTE

11h

24h

+1

 

 

 

20h

24h

 

31h

24h

+1

 

40h

24h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHT

13h

31h

+3

 

 

 

20h

31h

 

33h

31h

+3

 

40h

31h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTRAST

13h

32h

+3

 

 

 

20h

32h

 

33h

32h

+3

 

40h

32h

COLOR

13h

33h

+3

 

 

 

20h

33h

 

33h

33h

+3

 

40h

33h

TINT

13h

34h

+3

 

 

 

20h

34h

 

33h

34h

+3

 

40h

34h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHARPNESS

13h

35h

+3

 

 

 

20h

35h

 

33h

35h

+3

 

40h

35h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H.PHASE

13h

37h

+3

 

 

 

20h

37h

 

33h

37h

+3

 

40h

37h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H.POSIT

14h

38h

+4

 

 

 

 

––––––

 

34h

38h

+4

 

40h

38h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H.SIZE

14h

36h

+4

 

 

 

 

––––––

 

34h

36h

+4

 

40h

36h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V.POSIT

14h

3Ah

+4

 

 

 

 

––––––

 

34h

3Ah

+4

 

40h

3Ah

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR BALANCE R

13h

3Bh

+3

 

 

 

20h

3Bh

 

33h

3Bh

+3

 

40h

3Bh

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR BALANCE B

13h

3Dh

+3

 

 

 

20h

3Dh

 

33h

3Dh

+3

 

40h

3Dh

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO ADJUST

11h

3Ch

+1

 

 

 

20h

3Ch

 

31h

3Ch

+1

 

40h

3Ch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLANK

11h

41h

+1

 

 

 

20h

41h

 

31h

41h

+1

 

40h

41h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAGNIFY

11h

15h

+1

 

 

 

20h

15h

 

31h

15h

+1

 

40h

15h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FREEZE

11h

16h

+1

 

 

 

20h

16h

 

31h

16h

+1

 

40h

16h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

Connection to the control signal terminal (continued)

 

 

 

 

Command data chart

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item

 

 

 

 

 

 

Data code

 

 

MOUSE

00h=disable mouse function, 01 7Fh=start mouse function

 

 

COMMUNICATE

0Xh=8N1, 1Xh=7N1

 

 

 

 

 

 

X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps

 

 

 

 

 

 

POWER

3Eh=power off (standby status), 3Fh=power on

 

 

 

 

 

 

 

ZOOM

01 3Fh=Zoom +, 41 7Fh=Zoom –

 

 

 

 

 

 

FOCUS

01 3Fh=Focus +, 41 7Fh=Focus –

 

 

 

MIRROR

00h=Normal, 01h=H : Invert, 02h=V : Invert, 03h=H & V : Invert

 

 

 

 

 

 

 

INPUT

11h=VIDEO, 21h=RGB1, 22h=RGB2

 

 

 

SYSTEM (VIDEO)

00h

00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4. 43

 

 

 

00h

02h=PAL, 00h 03h=SECAM, 00h 05h=M-PAL,00h06h=N-PAL

 

 

 

 

 

 

 

 

VOLUME

00h

(low volume) 24h (high volume)

 

 

 

MUTE

00h=mute off,

01h=mute on

 

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHT

00h

00h

00h

(dark) 00h

00h

24h (bright)

 

 

CONTRAST

00h

00h

00h

(low) 00h

00h

24h (strong)

 

 

COLOR

00h

00h

00h

(pale) 00h

00h

24h (dense)

 

 

TINT

00h

00h

00h

(reddish) 00h 00h 24h (greenish)

 

 

SHARPNESS

00h

00h

00h

(soft) 00h

00h

24h (sharp)

 

 

H.PHASE

00h

00h

00h

00h 00h

24h

 

 

 

 

H.POSIT

00h

00h

00h

01h (Right) moves one step

 

 

 

00h

00h

00h

7Fh (Left) moves one step

 

 

H.SIZE

00h

00h

00h

01h (Large) moves two step

 

 

 

00h

00h

00h

7Fh (Small) moves two step

 

 

 

 

 

 

 

 

 

V.POSIT

00h

00h

00h

01h (Up) moves one step

 

 

 

00h

00h

00h

7Fh (Down) moves one step

 

 

 

 

 

 

 

 

 

 

 

COLOR BALANCE R

00h

00h

00h

(Light red) 00h

00h

24h (Dark red)

 

 

COLOR BALANCE B

00h

00h

00h

(Light blue) 00h

00h

24h (Dark blue)

 

 

AUTO ADJUST

00h

(AUTO ADJUST (Play)), 07h (AUTO ADJUST (stop))

 

 

BLANK

0Xh=blanking off, 1Xh=blanking on

 

 

 

 

X=8 Black, X=9 Blue, X=F White

 

 

 

 

 

 

 

 

MAGNIFY

00h=normal display, 01h=zoom Magnify display or Magnify ratio up.

 

 

 

7Fh=zoom ratio down

 

 

 

 

 

 

 

 

 

FREEZE

00h=normal display, 01h=still image display

 

 

 

 

 

 

 

 

 

 

 

 

The command code configuration consists of a 2-bytecommand and the following data.

The first byte of a command indicates the command type with 3 bits on the MSB side and the data length with 4 bits on the LSB side.

Projector - computer

Computer - projector

‘0xH’ : Error code

‘2xH’ : inquiry code

‘1xH’ : response code

‘3xH’ : setting code

‘70H’ : frame error code

‘4xH’ : default setting code

‘x’ indicates the data length (example: x=2 means a 2-bytecommand).

• The second byte of a command indicates the command contents.

29

Connection to the control signal terminal (continued)

Requesting projector status

(1)Send the request code ‘20H’ + ‘yyH’ from the computer to the projector.

(2)The projector returns the response code ‘1xH’ + ‘yyH’ +data to the computer.

Changing the projector settings

(1)Send the setting code ‘3xH’ + ‘yyH’ +data from the computer to the projector.

(2)The projector changes the setting based on the above setting code.

(3)The projector returns the response code ‘1xH’ + ‘yyH’ +data to the computer.

Caution The response data in (3) above need not match the setting data in (1).

For example, when the projector cannot set the setting data in (1), the projector may set the closest value. That value will be used as the response data in (3). Or else the projector will return the error code ‘0xH’ + ‘yyH’ +data.

Using the projector default settigns

(1)The computer sends the default setting code ‘40H’ + ‘yyH’ to the projector.

(2)The projector changes the specified setting to the default value.

(3)The projector returns the default value with the response code ‘1xH’ + ‘yyH’ =data.

When a command sent by the projector cannot be understood by the computer

(1)The computer sends the command code ‘3xH’ , ‘4xH’ or ‘4xH’ + ‘yyH’ +data to the projector.

(2)When the command sent by the projector cannot be understood, the error command ‘00H’ + ‘yyH’ is returned by the computer.

When data sent by the projector cannot be understood

(1)The computer sends the command code ‘3xH’ , ‘4xH’ or ‘4xH’ + ‘yyH’ +data to the projector.

(2)When the command sent by the projector cannot be understood, the the error code ‘0xH’ +‘yyH’ +data is returned.

When the data length is greater than indicated by the data length code, the projector will ignore the excess data code.

Conversely, when the data length is shorter than indicated by the data length code, an error code will be returned to the projector.

When a frame error occurs

Repeats 10 times per second until there is some sort of response to the error code 70H + 70H.

When the interval between bytes in one command is 500ms or greater

When a command or data is not sent within 500ms after the command code ‘2xH’ , ‘3xH’ or ‘4xH’ is sent by the computer, the error command ‘70H’ +‘70H’ will be returned as soon as the 500ms elapses. After this, if there is no response within 1 sec., a frame error will occur.

Caution • Operation cannot be guaranteed when the projector receives an undefined command or data.

• Provide an interval of at least 40ms between the response code and any other code.

30

Example of system setup

Computer

AC input

 

(notebook type)

 

 

 

1

RGB IN

2

S-VIDEOIN

 

 

 

VIDEO IN

CONTROL

 

RGB OUT

 

 

 

AUDIO IN

 

 

L

 

 

MONO

 

 

R

AUDIO IN

AUDIO

1

2

OUT

 

 

USB

Computer

Video tape recorder with S jack

(desktop type)

 

Video tape recorder

Speaker (with built-inamp)

Display monitor

Caution Turn power off to all devices before connecting.

Refer to the instruction manual of each device before connecting.

Cleaning the Air filter

Clean the air filter about every 100 hours .

1

Turn off the MAIN POWER switch of the projector and

 

pull out the power cord.

 

2

Remove the front air filter.

 

 

Filter

Model

 

Air Filter

MU00831

31

Cleaning the Air filter (continued)

3

Cleaning the air filter with a vacuum cleaner

4

Installing the air filter

Caution When the air filter becomes clogged with dust, etc., the projector power may turn off to prevent the internal heat level rising.

Do not operate the projector with the air filter removed.

Lamp

The light source lamp has a service life.

When used for an extended time, the images may become darker and the colors may deteriorate.

A malfunction could occur if the projector is used in this condition, so replace the lamp with a new one.

The following indicator or a message which appears when the power is turned on will indicate when the lamp should be replaced.

At such time, it is necessary to replace the lamp with a new one. For lamp replacement, please contact your dealer or service company.

Caution

The indicator lamp will also light red when the lamp unit overheats. In such case, turn off the

 

main power switch, wait for a while (approx. 20 min.) and then turn the power on again. If the

 

indicator lamp lights red again when the power is turned on, contact your dealer or service

 

company.

 

 

Message table

Screen displays

The following messages are displayed on the screen.

CHANGE THE LAMP“CALL

The total lamp usage time is nearing the service life of the lamp. Replace whith a new lamp.

A MAINTENANCE PERSON”

The lamp will turn off automatically when the lamp replacement time has been exceeded. *1

“CHANGE THE LAMP”

The total lamp time is nearing the lamp replacement time. After (*) hours, the lamp will turn

“CALL

off. Quickly replace with a new lamp. *1

A MAINTENANCE PERSON”

*Indicates the number of hours until the lamp turns off automatically.

“THE POWER WILL

 

TURN OFF AFTER * hr.”

 

 

 

Blinking of

The total lamp time has exceeded the replacement time. The lamp will blink for

“CHANGE THE LAMP”

approximately 10 min. and then turn off automatically. Replace with a new lamp.

 

 

NO INPUT IS DETECTED

There is no signal input (refer to pages 22, 23).

 

 

 

SYNC IS OUT OF RANGE

The current horizontal or vertical frequency cannot be used by this projector (refer to pages 23, 24).

 

 

 

*1 This display will disappear after 3min. but will reappear when the power is turned on again.

32

Message table (continued)

Indicators

The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases.

POWER

LAMP

TEMP

Message

 

Processing

indicator

indicator

indicator

 

 

 

 

 

 

 

 

 

 

 

 

Lights orange

Turns off

Turns off

Standby status

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashes green

Turns off

Turns off

Warming up

 

 

 

 

 

 

 

 

 

 

 

 

 

Lights green

Turns off

Turns off

Operation status *1

 

 

 

 

 

 

Flashes orange

Turns off

Turns off

Cool down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wait some time (approx. 20 min.) before

Lights red

Lights red

Turns off

The lamp does not light. *2

turning the power on again. If the

 

 

 

 

indicator still lights, the lamp may have

 

 

 

 

failed and. Replace with a new lamp.

 

 

 

 

 

 

 

Lights red

Flashes red

Turns off

A lamp has not been inserted

Firmly insert the lamp as far as possible

or the lamp cover is missing.

and screw the lamp cover in place.

 

 

 

 

 

 

 

 

 

 

Lights red

Turns off

Flashes red

The cooling fan is not operating.

Contact your dealer.

 

 

 

 

 

 

 

Flashes red

Flashes red

Turns off

The total lamp time has

Contact your dealer.

exceeded the replacement time.

When the LAMP or TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your dealer or service company.

*1: When the cooling fan is stopped and the interior becomes overheated, the power will turn off automatically to allow cooling (the indicator will turn off). In such cases, turn off the projector power, allow the set to cool and then turn the projector power on again. The lamp will then light. If the lamp does not light, contact your dealer or service company.

*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP indicator will flash red. In such cases, turn off the MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.

When you think something wrong

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Symptom

Possible cause

 

Remedy

Page

 

 

 

 

The power is not

•The main power switch is not turned on.

•Turn on the main power switch.

P.13

turned on.

•The power cord is disconnected.

•Plug the power cord into an AC power outlet.

P.9

 

 

 

 

No video or audio.

•The input is not correctly set.

•Use the projector or remote control to set.

P.8,10,

 

 

 

 

13,19

 

•No signal input.

•Connect correctly.

P.9,31

Video is present but

•The projector is not correctly connected.

•Connect correctly.

P.9,31

no audio.

•The volume is seet to minimum.

•Press VOLUME + on the remote control or display

P.10,18

 

 

the menu screen and adjust the volume.

 

 

•Mute is turned on.

•Press the MUTE button.

P.8,10

 

•Audio is switched to Video when P in P is on.

•Displays the Volume bar and switches the Audio input.

P.10

 

 

 

 

Audio is present but

•The projector is not correctly connected.

•Connect correctly.

P.9,31

no video.

•The brightness adjustment knob is rotated

•Select BRIGHT with the MENU button and then

P.17

 

fully clockwise.

press the (

) key.

 

 

•The lens cap is still on.

•Remove the lens cap.

P.13

 

 

 

 

 

Colors are pale and

Color density and color matching are not

Adjust the video.

P.18

color matching is poor.

correctly adjusted.

 

 

 

 

 

 

 

Images are dark.

•Brightness and contrast are not correctly adjusted.

•Adjust the video.

P.18

 

•The lamp is nearing the end of its service life.

•Replace with a new lamp.

P.32

 

 

 

 

Video is blurred.

Focus or H PHASE is out of adjustment.

Adjust the focus or H PHASE.

P.13,18

 

 

 

 

The LAMP indicator

Lamp failure.

Wait approximately 20 min. and then turn the

P.33

lights red.

 

power on again.

 

The TEMP indicator

Internal overheating.

•Make sure the ventilation openings are not blocked.

P.31,32

lights red.

 

•Clean the air filter.

 

 

 

•Lower the ambient temperature to 35 degrees C or less.

 

 

 

 

 

 

A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.

33

Specifications · ALL specifications are subject to change without notice.

Product name

 

Liquid crystal projector

 

 

 

Model

 

28A8800A

 

 

 

Display method

 

Three liquid crystal panels, three primary color system.

 

 

 

Liquid crystal

Panel size

3.3 cm (1.3 type)

 

 

 

panel

Drive system

TFT active matrix

 

 

 

 

Number of pixels

786,432 pixels ( 1024 horizontal x 768 vertical)

 

 

 

Lens

 

Zoom lens F=1.7~2.3 f=49~64mm

 

 

 

Lamp

 

190w UHB

 

 

 

Speaker

 

1.2W + 1.2W (Stereo)

 

 

 

Power supply

 

AC100 ~ 120V, 3.7A / AC220 ~ 240V, 1.5A.

 

 

 

Power consumption

320W

 

 

 

Operating temperature range

0 ~ 35˚C

 

 

 

Size

 

11" (W) × 5" (H) 14" (D)

 

 

 

Weight (mass)

 

13 lbs

 

 

 

 

 

S VIDEO: mini DIN 4-pinjack

VIDEO signal input jacks

VIDEO: RCA jack

 

 

AUDIO: RCA jack

 

 

 

RGB signal input/output jacks

RGB signals: D-sub15-pinshrink jack

 

 

Audio: stereo mini-jack

 

 

 

CONTROL signal jack

D-sub15-pinshrink jack

 

 

 

Dimensional Diagram

Unit: inches

14"

11"

3" 5"

1"

34

LEGAL INFORMATION

FIVE-YEARLIMITED WARRANTY

This Dukane LCD projector is warranted to the original purchaser for a period of five (5) years from the original purchase date - in normal use and service - against defects in material and workmanship. DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

During the warranty period, Dukane Corporation will repair or replace (at the manufacturer's option) any such defective parts (except for the lamp, which is subject to whatever warranties the manufacturer may provide) without charge to the purchaser for parts or labor when the product is returned, prepaid and insured, with proof-of-purchasedate. This remedy is void if the product has been

damaged by accident, unreasonable use, neglect, improper service or other causes not arising out of defects in material or workmanship.

Dukane Corporation disclaims all liability for incidental or consequential damage of any kind, including all damages arising out of any interruptions in operation of the product and all damages to software.

No person, firm, or representative is authorized to assume any obligation or to make any warranty on behalf of the Dukane Corporation other than as stated above.

THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA. FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.

LAMP REPLACEMENT SERVICE & REPAIR POLICY & PROCEDURE

For service and parts, contact the Dukane AV Service Department at 1 (800) 676-2487within the USA or 1 (630)584-2300worldwide.

If you would like to send a facsimile (FAX), dial 1 (630) 584-5156worldwide.

When requesting warranty service, please have the sales receipt available along with the model name and serial number.

If it becomes necessary to return the projector, use the original packing material and box (if retained) or pack securely. Dukane Corporation will not be liable for any pick-upor delivery charges or any expenses incurred for service calls or service supplied by anyone other than the Dukane AV Service Department.

Audio Visual Products

Dukane Corporation

Phone: (630) 584-2300

Audio Visual Products Division

Orders: (800) 676-2485

2900 Dukane Drive

Information: (800)

676-2486

St. Charles, IL 60174-3395

Fax: (630)

584-5156

E-mail:avsales@dukane.com

Parts & Service: (800)

676-2487

 

Fax: (630)

584-0984

Part # 401-552-02