XHD6420
INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA/3.5mm Receiver with Built-In HD Radio™ and Detachable Face
R
XHD6420 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
•Remove trim ring from unit,
•Remove 2 transit screws located on top of the unit.
•Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
•Install mounting sleeve into opening, bending tabs to secure.
•Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
•Certain vehicles may require an installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
XHD6420 INSTALLATION
Antenna Connector
Wiring Diagram
FUSE
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XHD6420 uses one
10 amp ATM fuse located beside the wiring connector.
XHD6420 OPERATION
Control Locations - Receiver
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
24 |
23 |
22 |
21 |
20 |
19 |
18 |
17 |
16 |
15 |
14 |
13 |
12 |
11 |
10 |
1 |
|
Release |
|
|
|
13 |
Preset 6/Folder Up |
|
|
|
||||
2 |
|
Eject |
|
|
|
|
14 |
Preset 5/Folder Down |
|
|
||||
3 |
|
Mode/Search |
|
|
15 |
Preset 4 |
|
|
|
|
|
|||
4 |
|
Volume/Audio/Setup |
|
16 |
Preset 3/Intro |
|
|
|
||||||
5 |
|
Tune/Track Up |
|
|
17 |
Preset 2/Random |
|
|
|
|||||
6 |
|
IR Remote Sensor |
|
18 |
Preset 1/Repeat |
|
|
|
||||||
7 |
|
Loudness |
|
|
|
19 |
Auto Store/Preset Scan/Enter |
|
||||||
8 |
|
EQ/Key 9 |
|
|
|
20 |
Band/Play/Pause |
|
|
|
||||
9 |
|
Display/Key 0 |
|
|
21 |
HD Seek |
|
|
|
|
|
|||
10 |
|
Auxiliary Input |
|
|
22 |
Mute |
|
|
|
|
|
|||
11 |
|
Tuner Scan/Key 8 |
|
23 |
Tune/Track Down |
|
|
|
||||||
12 |
|
Key 7 |
|
|
|
|
24 |
Power |
|
|
|
|
|
The XHD6420 allows playback of your favorite MP3 and WMA files recorded on CD-R and CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track search - even while a song is currently playing!
Function keys 7, 8, 9 and 0 apply to MP3/WMA operation only.
XHD6420 OPERATION
General Operation
Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.
Semi-Permanent Remove trim ring and install supplied #1 x 7/32” Phillips Faceplate Installation head screw through left side of mounting frame into faceplate.
Power On/Off Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off.
Mode Press MODE to select between AM/FM, CD player and auxiliary input. Modes of operation are indicated in the display.
Note: CD mode will not appear unless a CD is inserted.
Auxiliary Input Insert 3.5 mm plug to connect your portable audio device.
Volume Adjust volume using rotary encoder (00-46).
Programmable Press and hold POWER for 3 seconds to program currently Turn-On Volume selected volume level. "P-VOL" and the current volume level will momentarily appear in the display.
Mute Press MUTE to silence the audio. “MUTE” will flash in the display. Press MUTE again to cancel.
Preset EQ Curves Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected).
Reset Press to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate.
Display Press DISP to select between clock and different types of information, such as radio frequency, HD Radio song information, CD track/elapsed time or MP3/WMA song information.
XHD6420 OPERATION
General Operation
Set the Clock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE nnto adjust the hours and TUNE llto adjust the minutes. Press DISP momentarily to save the selected time.
Setup Menu Press and hold the rotary encoder for more than 3 seconds to access the setup menu. Press the rotary encoder momentarily to select between the menu functions and rotate the rotary encoder left/right to adjust or activate the desired function.
Setup Menu
Menu Function |
Options |
Action |
Clock Display |
CLK OFF |
Programs the unit to not display the clock when the |
|
|
power is off. |
|
CLK ON |
Programs the unit to display the clock when the |
|
|
power is off. |
Auxiliary Input |
AUX ON |
Enables the front panel 3.5mm auxiliary input. |
|
AUX OFF |
Disables the auxiliary input. |
Beep Confirmation |
BEEP OFF |
Disables the confirmation beep. |
|
BEEP ON |
Enables the confirmation beep. |
Local/Distance |
LOC OFF |
Activates distance tuning. |
Tuning |
LOC ON |
Activates local tuning for strong station reception |
|
|
only. |
Power on Message |
MSG OFF |
Disables power on message. |
|
MSG ON |
Enables power on message to be displayed. |
Demonstration |
DEMO OFF |
Disables the demonstration mode. |
Mode |
DEMO ON |
Enables the "BUILT IN HD RADIO" message. |
Display Scrolling |
SCRL ON |
Programs the unit to scroll display information |
|
|
continuously. |
|
SCRL OFF |
Disables the display scroll feature. |