Directed Electronics 110XV User Manual

0 (0)

[ Put a stop to crime ]

S e c u r i t y s y s t e m a n d c o n v e n i e n c e

MODEL

[ User guide ] 110

Limited Consumer Warranty

For a period of five calendar year from the date of purchase of this device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model), free of cost, any electronic control module which proves to be defective in workmanship or material under normal use, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page.

After the fifth calendar year, from the date of purchase of this device, Directed Electronics, Inc., promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model) any electronic control module which proves to be defective in workmanship or material under normal use FOR A CHARGE OF $45.00, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page.

This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or understandings, whether written or oral. IN ANY EVENT, DIRECTED ELECTRONICS, INC. IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND/OR ITS CONTENTS.

This warranty is void if the product has been damaged by accident, unreasonable use, neglect, improper service or other causes not arising out of defects in materials or construction. This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries. The unit in question must be returned to the manufacturer, postage prepaid. This warranty does not cover labor costs for the removal, diagnosis, troubleshooting or reinstallation of the unit. For service on an out-of-warranty product a flat rate fee by model is charged. Contact your authorized dealer to obtain the service charge for your unit.

These systems are a deterrent against possible theft. Directed Electronics, Inc. is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and/or its contents. Directed Electronics does not authorize any person to create for it any other obligation or liability in connection with this security system.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOWING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IMPORTANT NOTE:

This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have completed the warranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the address listed on the warranty registration card.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■Date of purchase

■Your full name and address

■Authorized dealer's company name and address

■Type of system installed

■Year, make, model and color of the automobile

■Automobile license number

■Vehicle identification number

■All security options installed on automobile

■Installation receipts

table of contents

limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . i standard transmitter configuration. . . . . . . . . . . . . . . . . . . . . . . . . 3 what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 warning! safety first. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 passive arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . 12 arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . 14 silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 panic mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 remote start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 short-run/turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 timer mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 safety features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . 22 disabling the remote start system . . . . . . . . . . . . . . . . . . . . . 22 over and under rev protection. . . . . . . . . . . . . . . . . . . . . . . . 22 shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . 23 diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . 27 code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . 33 glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2	© 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c .

standard transmitter configuration

controls the Arm and Panic On/Off function.

controls the Disarm and Panic Off function.

controls Silent Mode™ and Auxiliary channel 2 output.

controls the Remote Start function.

and	pressed together control the Timer mode.

and pressed together control Turbo/Short Run.

and pressed together control channel 4 output.

and pressed together control channel 5 output

what is included

A control module

An XHF receiver/antenna

Two four-button transmitters

A Stinger™ DoubleGuard® two-stage shock sensor

A Revenger™ Soft Chirp™ six-tone programmable siren

A status LED indicator light

A push-button Valet® switch

Your warranty registration

A shut-down toggle switch

important information

Congratulations on the purchase of your combination remote start alarm system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this product by anyone other than an authorized dealer voids the warranty. All dealers are provided with a preprinted dealer certificate to verify authorization.

By carefully reading this Owner's Guide prior to using your system, you will maximize the use of this system and its features. You can print additional or replacement copies of this manual by accessing our web site at www.directed.com.

4	© 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c .

system maintenance

The system requires no specific maintenance. Your remote is powered by a small, lightweight 3-volt lithium battery that will last approximately one year under normal use. When the battery begins to weaken, operating range will be reduced and the LED on the remote will dim.

your warranty

Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Make sure you receive the warranty registration from your dealer. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer.

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device.

caution

This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use.

transmitter functions

The receiver uses a computer-based Learn Routine to learn the transmitter buttons. This makes it possible to assign any remote transmitter button to any receiver function. The transmitter initially comes programmed with Standard Configuration, but may also be customized by an authorized dealer. The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter.

standard configuration

Button

The arming and panic functions are controlled by pressing this button for one second.

Button

The disarming function is controlled by pressing this button for one second.

Button

Silent Mode™ and an optional auxiliary function are controlled by this button. (Silent Mode works by pressing this button for

6	© 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c .

less than one second before arming or disarming. An optional auxiliary function, such as trunk release, can be controlled by pressing this button for 1.5 seconds.)

The auxiliary output controls __________________________.

Button

The remote start function of your system is controlled by pressing this button twice within 3 seconds.

and Buttons

An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

The remote start timer mode is controlled by pressing these buttons simultaneously.

and Buttons

The short-run turbo mode is activated when these buttons are

pressed simultaneously.

using your system

warning! safety first

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility of the user.

Use of this product in a manner contrary to its intended

8	© 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c .

mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in the product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the authorized Directed dealer to fix the problem.

After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All installations must be performed by an authorized Directed dealer. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE

UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED DIRECTED DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

active arming

You can arm the system by pressing of your transmitter for one second. When the system arms, you will hear a short siren sound, or chirp, and see the parking lights flash once. If the power door locks are controlled by the system, the doors will also lock. While the system is armed, the status LED will flash approximately once per second, indicating that the system is actively protecting your vehicle. If you hear a second chirp after arming and note that the status LED is flashing in groups, see the Diagnostics Section of this guide. This extra chirp is called Bypass Notification.

passive arming

The system can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door. Whenever the system is in its 30-second passive arming countdown, the status LED will flash twice as fast as it does when the system is armed. At the 20-second point of the count-

10	© 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c .

+ 30 hidden pages