Delta ShopMaster CP200 User Manual

Size:
1.89 Mb
Download

Oil-Free

Air Compressor

(CP200)

PART NO. D27930 Rev.0

Copyright © 2002 Delta Machinery

 

 

To learn more about DELTA MACHINERY

 

ESPAÑOL: PÁGINA 19

visit our website at: www.deltamachinery.com.

FRANÇAIS: PAGE 37

 

For Parts, Service, Warranty or other Assistance,

please call 1-866-422-4286.

MANUAL INSTRUCTION

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and

PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these symbols.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates an

 

 

 

 

 

 

Indicates a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

imminently hazardous

 

 

 

 

 

 

potentially hazardous

 

 

 

 

 

 

 

 

 

 

 

 

 

 

situation which, if not avoided, will

 

 

situation which, if not avoided, may

 

 

result in death or serious injury.

 

 

result in minor or moderate injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Used without the

 

 

 

 

 

Indicates a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

potentially

 

 

 

 

 

 

 

safety alert symbol

 

 

 

 

 

 

 

 

 

 

 

 

 

hazardous situation which, if not

 

 

indicates a potentially hazardous

 

avoided, could result indeath or

 

 

situation which, if not avoided, may

 

serious injury.

 

 

result in property damage.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals

known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are:

lead from lead-basedpaints

crystalline silica from bricks and cement and other masonry products

arsenic and chromium from chemically-treatedlumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.

When using air tools, basic safety precautions should always be followed to reduce the risk of of personal injury.

D27930

2- ENG

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

Improper operation or maintenance of this product could result in serious injury and property damage. Read and understand all warnings and operation instructions before using this equipment.

HAZARD

WARNING: Risk of explosion or fire

What Could Happen

It is normal for electrical contacts within the motor and pressure switch to spark.

If electricalsparks from compressorcome into contact with flammable vapors, they may ignite, causing fire or explosion.

Restricting any of the compressor ventilation openingswill cause serious overheating and could cause fire.

Unattended operation of this product could result in personal injury or property damage. To reduce the risk of fire, do not allow the compressor to operate unattended.

How To Prevent It

Always operate the compressor in awell ventilated area free of combustible materials, gasoline, or solvent vapors.

If spraying flammable materials, locate compressor at least 20 feet away from spray area. An additional length of hose may be required.

Store flammable materials in a secure location away from compressor.

Never place objects against or on top of compressor. Operate compressor in an open area at least 12 inches away fromany wall or obstructionthat would restrict the flow of fresh air to the ventilation openings.

Operate compressor in a clean, dry well ventilated area. Do not operate unit indoors or in any confined area.

Always remain in attendance with the product when it is operating.

Always disconnect electrical power by moving pressure switch lever to the off position and drain tank daily or after each use.

3- ENG

D27930

HAZARD

WARNING: Risk of Bursting

Air Tank: The following conditions could lead to a weakening of the tank, and result in a violent tank explosion and could cause property damage or serious injury.

What Could Happen

How To Prevent It

1. Failure to properly drain

Drain tank daily or after each use. If

condensed water from tank,

tank develops a leak, replace it

causing rust and thinning of the

immediately with a new tank or replace

steel tank.

the entire compressor.

2. Modifications or attempted repairs

Never drill into, weld, ormake any

to the tank.

modifications to the tank or its

3. Unauthorized modifications to the

attachments.

 

unloader valve, safety valve, or any

 

other components which control

 

tank pressure.

 

4.Excessive vibration can weaken The tank is designed to withstand specific

the air tank and cause rupture or

operating pressures. Never make

explosion

adjustments or parts substitutions to

 

alter the factory set operating

 

pressures.

ATTACHMENTS & ACCESSORIES:

For essential control of air pressure, you

Exceeding the pressure rating of air

must install a pressure regulator and

tools, spray guns, air operated

pressure gauge to the air outlet (if not

accessories, tires, and other inflatables

equipped) of your compressor. Follow the

can cause them to explode or fly apart,

equipment manufacturers

and could result in serious injury.

recommendation and never exceed the

 

maximum allowable pressure rating of

 

attachments.

HAZARD

WARNING: Risk from Flying Objects

WHAT CAN HAPPEN

The compressed airstream can cause soft tissue damageto exposed skin and can propeldirt, chips, loose particles, and small objects at high speed, resulting in property damage or personal injury.

HOW TO PREVENT IT

Always wear ANSI Z87.1 approved safety glasses with side shieldswhen using the compressor.

Never point any nozzle or sprayer towardany part of the body or at other people or animals.

Always turn the compressor off and bleed pressurefrom the air hose and tank before attempting maintenance, attaching tools or accessories.

D27930

4- ENG

HAZARD

WARNING: Risk of Electrical Shock

WHAT CAN HAPPEN

Your air compressor is powered by electricity.Like any other electrically powered device, If it is not used properly it may cause electric shock.

Repairs attempted by unqualified personnel can result in serious injury or death by electrocution.

Electrical Grounding: Failure to provide adequate grounding to this product could result in serious injury or death from electrocution.

See grounding instructions.

HOW TO PREVENT IT

Never operate the compressor outdoors when it is raining or in wet conditions.

Never operate compressor with protective covers removed or damaged.

Any electrical wiring or repairsrequired on this product should be performed by authorized service center personnelin accordance with national and local electrical codes.

Make certain that the electrical circuit to which the compressor is connected provides proper electrical grounding, correct voltage and adequate fuse protection.

HAZARD

WARNING: Risk to Breathing

WHAT CAN HAPPEN

The compressed air directly from your compressoris not safe for breathing. Theair stream may contain carbon monoxide, toxic vapors, or solid particles from the tank.Breathing thesecontaminants can cause serious injury or death.

Sprayed materials such as paint, paint solvents, paint remover, insecticides, weed killers, maycontain harmful vapors and poisons.

HOW TO PREVENT IT

Air obtained directly from the compressorshould never be used to supply air for human consumption. In order to use air produced by this compressor for breathing, suitablefilters and in-linesafety equipment must be properly installed. In-linefilters and safety equipment used in conjunction with the compressormust be capable of treating air to all applicable local and federal codes prior to human consumption.

Work in an area with good cross ventilation. Read and follow the safety instructionsprovided on the label or safety data sheets for the materials you are spraying. Use a NIOSH/ MSHA approved respiratordesigned for use with your specific application.

5- ENG

D27930

HAZARD

WARNING: RISK OF BURNS

WHAT CAN HAPPEN

Touching exposed metal such as the compressor head or outlet tubes, can result in serious burns.

HOW TO PREVENT IT

Never touch any exposed metal parts on compressor during or immediately after operation. Compressor will remain hotfor several minutes after operation.

Do not reach around protective shrouds orattempt maintenance until unit has been allowed to cool.

HAZARD

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN

HOW TO PREVENT IT

Moving parts such as the pulley, flywheel,

Never operate the compressor with

and belt can cause serious injuryif they

guards or covers which aredamaged or

com into contact with you or your

removed.

clothing.

 

 

 

Attempting to operate compressor with

Any repairs required on this product

damaged or missing parts or attempting

should be performed by authorized

to repair compressor with protective

service center personnel.

shrouds removed can expose you to

 

moving parts and can result in serious

 

injury.

 

HAZARD

WARNING: RISK OF FALLING

WHAT CAN HAPPEN

A portable compressor can fallfrom a table, workbench, or roof causing damage to the compressor and could result in serious injury or death to the operator.

HOW TO PREVENT IT

Always operate compressor in a stable secure positionto prevent accidental movement of the unit. Never operate compressor on a roof or other elevated position. Use additional air hose to reach high locations.

D27930

6- ENG

HAZARD

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN

Unsafe operation of your air compressor could lead to serious injury or death to you or others.

HOW TO PREVENT IT

Review and understand all instructions and warningsin this manual.

Become familiar with the operation and controls of the air compressor.

Keep operating area clear of all persons, pets, and obstacles.

Keep children away from the air compressor at all times.

Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times.

Never defeat the safety features of this product.

Equip area of operation with a fire extinguisher.

Do not operate machine with missing, broken, or unauthorized parts.

7- ENG

D27930

GLOSSARY

Become familiar with these terms before operating the unit. CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air delivery.PSIG: Pounds per square inch gauge; a unit of measure of pressure.Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL,CSA/US have been evaluated by OSHA certified independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety.

CSA: Electrical products sold in Canada are required to be certified to the applicable CSA standard (s). Canadian Standards Association (CSA) is a standards writing and safety testing organization. Products that are CSA certified have been evaluated and tested and found to meet or exceed the applicable CSA standard (s) for safety and electrical performance.

Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called“cut-in”pressure.

Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called“cut-out”pressure.

Branch Circuit: Circuit carrying electricity from electrical panel to outlet.

SPECIFICATIONS

Model No.

CP200

Voltage/Hertz/ Phase

120V/60/1

Minimum Branch Circuit Requirement

15 amps

*Fuse Type

Time Delay

Air Tank Capacity

2 gallons

Approximate Cut-inPressure

75 PSI

Approximate Cut-outPressure

100 PSI

* A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit on which the air compressor is operated. If compressor is connected to a circuit protected by fuses, use only time delay fuses. Time delay fuses should be marked “D” in Canada and “T” in the US.

D27930

8- ENG

INSTALLATION

HOW TO SET UP YOUR UNIT

Location of the Air Compressor

Locate the air compressor in a clean, dry and well ventilated area. The air compressor should be located at least 12" away from the wall or other obstructions that will interfere with the flow of air. The air compressor pump and shroud are designed to allow for proper cooling. The ventilation openings on the compressor are necessary to maintain proper operating temperature. Do not place rags or other containers on or near these openings.

GROUNDING INSTRUCTIONS

RISK OF ELECTRICAL SHOCK. In the event of a short circuit, grounding reduces the risk of shock by providing

an escape wire for the electric current. This air compressor must be properly grounded.

The portable air compressor is equipped with a cord having a grounding wire with an appropriate grounding plug (see illustrations). The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances.

1.The cord set and plug with this unit contains a grounding pin. This plug MUST be used with a grounded outlet.

IMPORTANT: The outlet being used must be installed and grounded in accordance with all local codes and ordinances.

2.Make sure the outlet being used has the same configuration as the grounded plug. DO NOT

USE AN ADAPTER.

Grounding

Pin

120 Volt U.S.A. Plug

Grounding

Pin

When used outside of the United 240 Volt U.S.A. Plug States of America a conversion kit may be required for

local use.

3.Inspect the plug and cord before each use. Do not use if there are signs of damage.

4.If these grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician.

IMPROPER GROUNDING CAN RESULT IN ELECTRICAL SHOCK.

Do not modify the plug provided. If it does not fit the available outlet, a correct outlet should be installed by a qualified electrician.

Repairs to the cord set or plug MUST be made by a qualified electrician.

9- ENG

D27930

Extension Cords

Using extension cords is not recommended. The use of extension cords will cause voltage to drop resulting in power loss to the motor and overheating. Instead of using an extension cord, increase the working reach of the air hose by attaching another length of hose to its end. Attach additional lengths of hose as needed.

If an extension cord must be used, be sure it is:

a 3-wireextension cord that has a3-bladegrounding plug, and a3-slotreceptacle that will accept the plug on the product

in good condition

no longer than 50 feet

14 gauge (AWG) or larger. (Wire size increases as gauge number decreases. 12 AWG, 10 AWG, and 8 AWG may also be used. DO NOT USE 16 OR 18 AWG.)

Voltage and Circuit Protection

Refer to the Parts Manual for the voltage and minimum branch circuit requirements.

Certain air compressors can be operated on a 15 amp circuit if the following conditions are met.

1.Voltage supply is 108V-132VAC at the outlet.

2.Circuit is not used to supply any other electrical needs (lights, appliances, etc.).

3.Circuit is equipped with a 15 amp circuit breaker minimum or 15 amp time delay fuse. NOTE: If compressor is connected to a circuit protected by fuses, use only time delay fuses marked “D” for Canada and "T" for US.

4.Extension cords comply with specifications.

If any of the above conditions cannot be met, or if operation of the compressor repeatedly causes interruption of the power, it may be necessary to operate it from a 20 amp circuit. It is not necessary to change the cord set.

D27930

10ENG

Drain
Valve

OPERATION

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

Description of Operation

Become familiar with these controls before operating the unit.

Auto/On/Off Switch: Set switch in AUTO/ON position to provide

automatic power to the pressure

Tank

 

switch and OFF to remove power

Pressure

Outlet

at the end of each use.

Gauge

Pressure

Pressure Switch (not shown):

 

Gauge

Auto/On/Off

 

The pressure switch automatically

 

starts the motor when the air tank

Switch

 

 

 

pressure drops below the factory

 

Regulator

set "cut-in"pressure. It stops the

 

 

motor when the air tank pressure

 

 

reaches the factory set "cut-out"

Safety

 

pressure.

 

Safety Valve: If the pressure

Valve

 

 

 

switch does not shut off the air compressor at its "cut-out"pressure setting, the safety valve will protect against high pressure by "popping out" at its factory set pressure (slightly higher than the pressure switch"cut-out"setting).Outlet Pressure Gauge: The outlet pressure gauge indicates the air pressure available at the outlet side of the regulator. This pressure is controlled by the regulator and is always less than or equal to the tank pressure.

Tank Pressure Gauge: The tank pressure gauge indicates the reserve air pressure in the tank.

Regulator: Controls the air pressure shown on the outlet pressure gauge. Pull the knob out and turn clockwise to increase pressure and counterclockwise to decrease pressure. When the desired pressure is reached push knob in to lock in place.

Drain Valve: The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use.

Cooling System (not shown): This compressor contains an advanced design cooling system. At the

heart of this cooling system is an engineered fan. It is

perfectly normal for this fan to blow air through the vent holes in large amounts. You know that the cooling system is working when air is being expelled. NOTE: It is normal for the fan to run continuously when the unit is in the "ON" position. To turn the fan off, switch the unit to the "OFF" positon.

Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

Check Valve (not shown): When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches"cut-out"pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

11ENG

D27930

Motor Overload Protector (not shown): The motor has an automatic reset thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. The compressor will automatically restart after the motor cools.

The motor will automatically restart without warning if plugged in electrical outlet and "Auto/On/Off" switch is in

the "AUTO/ON" position.

How to Use Your Unit

How to Stop:

1.Set the Auto/On/Off switch to "OFF". NOTE: It is normal for the fan to run continuously when the unit is in the "ON" position. To turn the fan off, switch the unit to the "OFF" positon.

Before Starting

Break-inProcedure

Serious damage may result if the following break-ininstructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the Auto/On/Off switch is in the "OFF" position.

2.Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.)

3.Open the drain valve fully (counterclockwise) to permit air to escape and prevent air pressure build up in the air tank during the break-inperiod.

4.Set the Auto/On/Off switch to "AUTO/ON" position. The compressor will start.

5.Run the compressor for 5 minutes. Make sure the drain valve is open and there is minimal air pressure build-upin tank.

6.After 5 minutes, close the drain valve (clockwise). The air receiver will fill to "cut-out"pressure and the motor will stop.

The compressor is now ready for use.

Before Each Start-Up:

1.Set Auto/On/Off switch to "OFF".

2.Turn regulator knob counterclockwise until it stops.

3.Attach hose and accessories.

Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s maximum pressure

rating for air tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating.

D27930

12ENG

How to Start:

1.Set the Auto/On/Off switch to "AUTO/ON" and allow tank pressure to build. Motor will stop when tank pressure reaches "cut-out"pressure.

2.Turn regulator knob clockwise until desired pressure is reached.

The compressor is ready for use.

NOTE: Always operate the air compressor inwell-ventilatedareas free of gasoline or other combustible vapors. If the compressor is being used to operate a sprayer DO NOT place near the spray area.

 

MAINTENANCE

Customer Responsibilities

 

 

 

 

 

Before each use

Daily or after

 

each use

 

 

Check Safety Valve

 

 

 

 

Drain Tank

 

To Check Safety Valve

If the safety valve does not work properly, overpressurization may occur, causing air tank

rupture or an explosion. Before starting compressor, pull the ring on the safety valve to make sure that the safety valve operates freely. If the valve is stuck or does not operate smoothly, it must be replaced with the same type of valve.

To Drain Tank

1.Set the Auto/On/Off switch to "OFF".

2.Turn regulator knob counterclockwise to set the outlet pressure to zero.

3.Remove the air tool or accessory.

4.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 psi. Release safety valve ring.

5.Drain water from air tank by opening drain valve (counter-clockwise)on bottom of tank.NOTE: Tilt tank forward to drain tank completely.

Water will condense in the air tank. If not drained, water will corrode and weaken the air tank

causing a risk of air tank rupture.

6.After the water has been drained, close the drain valve (clockwise). The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.

13ENG

D27930

STORAGE

Before you store the air compressor, make sure you do the following:

1.Review the "Maintenance" section on the preceding pages and perform scheduled maintenance as necessary.

2.Set the Auto/On/Off lever to "OFF".

3.Turn regulator knob counterclockwise and set the outlet pressure to zero.

4.Remove the air tool or accessory.

5.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 psi. Release safety valve ring.

6.Drain water from air tank by opening drain valve on bottom of tank.

Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air

tank rupture.

7.After the water has been drained, close the drain valve.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

8.Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind them loosely around the compressor handle. (If so equipped)

9.Store the air compressor in a clean and dry location.

D27930

14ENG

TROUBLESHOOTING

Performing repairs may expose voltage sources, moving parts or compressed air sources, moving parts or

compressed air sources. Personal injury may occur. Prior to attempting any repairs, unplug the air compressor and bleed off all air tank air pressure.

PROBLEM

CAUSE

CORRECTION

Fan continues

It is normal for the fan to run

to run when

continuously when the unit

Auto/On/Off

is in the "ON" position.

switch is in the

 

"ON" position.

 

To stop fan, Turn the Auto/On/Off switch to the "OFF" position.

 

Thermal

Low voltage

Extension cord is wrong

 

overload

 

length or gauge. Check

 

protector cuts

 

extension cord.

 

out repeatedly

Improper ventilation/

Operate compressor in a

 

 

temperature too high

well ventilated area.

 

 

Defective check valve

Contact a Trained Service

 

 

 

Technician

 

 

Defective valves

Contact a Trained Service

 

 

 

Technician

 

 

 

 

 

Excessive tank

Compressor does not turn

Set Auto/On/Off switch to

 

pressure - safety

off when compressor

the "OFF" position, if the

 

valve pops off.

reaches "cut-out"pressure.

unit does not shut off contact

 

 

 

a Trained Service Technician.

 

 

 

Contact a Trained Service

 

 

Pressure switch "cut-out"

Technician.

 

 

too high.

 

 

 

 

 

 

 

 

 

 

 

 

Air leaks at

Tube fittings are not tight

Using a soapy water solution

 

check all exposed fittings for

 

fittings.

enough.

 

leaks. If needed reseal

 

 

 

 

 

 

fittings with pipe sealant

 

 

 

tape and retighten securely.

 

 

 

Do Not Overtighten. If

 

 

 

leaks continue contact a

 

 

 

Trained Service Technician.

 

 

 

 

 

 

 

 

 

Air leaks in air

Defective air tank.

Air tank must be replaced.

tank or at air

 

Do not repair the leak.

tank welds.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Do not drill into, weld or

 

 

 

otherwise modify air tank

 

 

 

or it will weaken. The tank

 

 

 

can rupture or explode.

15ENG

D27930

 

PROBLEM

CAUSE

CORRECTION

Air leak from

Possible defect in safety

Operate safety valve

safety valve.

valve.

manually by pulling on ring.

 

 

 

If valve still leaks, it should

 

 

 

be replaced.

 

 

 

 

Pressure reading

It is normal for "some"

If there is an excessive

on the regulated

pressure drop to occur.

amount of pressure drop

pressure gauge

 

when the accessory is used,

drops when an

 

adjust the regulator following

accessory is

 

the instructions in the

used.

 

"Description of Operation"

 

 

 

paragraph in the "Operation

 

 

 

Section.

 

 

 

NOTE: Adjust the regulated

 

 

 

pressure under flow

 

 

 

conditions (while accessory

 

 

 

is being used).

 

 

 

 

Compressor is

Prolonged excessive use of

Decrease amount of air

not supplying

air.

usage.

enough air to

 

Check the accessory air

operate

Compressor is not large

accessories.

enough for air requirement.

requirement. If it is higher

 

 

 

than the SCFM or pressure

 

 

 

supplied by your air

 

 

 

compressor, you need a

 

 

 

larger compressor.

 

 

Hole in hose.

Check and replace if

 

 

 

required.

 

 

Air leaks.

Tighten fittings.

 

 

 

 

Excessive

Condensation in tank

Drain tank

"auto" starting

 

 

 

and stopping

 

 

 

 

 

 

 

 

D27930

16ENG

PROBLEM

CAUSE

CORRECTION

Motor will not

Motor overheated

Allow compressor to cool for

run.

 

approximately 30 minutes so

 

 

thermal overload switch will

 

 

reset. If unit still does not

 

 

start, empty air from tank and

 

 

refer to "Thermal overload

 

 

protector cuts out

 

 

repeatedly" information.

 

Fuse blown, circuit breaker

Check fuse box for blown

 

tripped.

fuse and replace as

 

 

necessary. Reset circuit

 

 

breaker. Do not use a fuse or

 

 

circuit breaker with higher

 

 

rating than that specified for

 

 

your particular branch circuit.

 

 

Check for proper fuse. You

 

 

should use a time delay fuse.

 

 

Check for low voltage

 

 

problem.

 

 

Check the extension cord.

 

 

Disconnect the other

 

 

electrical appliances from

 

 

circuit or operate the

 

 

compressor on its own

 

 

branch circuit.

 

Extension cord is wrong

Check the extension cord.

 

length or gauge.

 

 

Faulty motor.

Have checked by a Trained

 

 

Service Technician.

 

 

 

AIR COMPRESSOR REPAIR PARTS

For Parts, Service, Warranty or other Assistance, please call 1-866-422-4286.

17ENG

D27930

LIMITED WARRANTY

DELTA MACHINERY warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods:

3 YEARS - Limited warranty on2-stageoil-freeair compressor pumps that operate at 1725 RPM.2 YEARS - Limited warranty onoil-lubricatedair compressor pumps.

1 YEAR - Limited warranty on all other air compressor components.2 YEARS - Limited warranty on electric generator alternators.

1 YEAR - Limited warranty on other generator components.

2 YEARS - Limited warranty on pneumatic air tools as described in Delta general catalog.

1 YEAR - Limited warranty on pressure washers used in consumer applications (i.e. personal residential household usage only).

90 DAY - Pressure washers used for commercial applications (income producing) and service parts.1 YEAR - Limited warranty on all accessories.

Delta will repair or replace, atDelta's option, products or components which have failed within the warranty period. Service will be scheduled according to the normal work flow and business hours at the service center location, and the availability of replacement parts. All decisions ofDelta Corporation with regard to this limited warranty shall be final.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

RESPONSIBILITY OF ORIGINAL PURCHASER (initial User):

To process a warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by an Delta Authorized Warranty Service Center. For the location of the nearest Authorized Warranty Service Center call1-866-422-4286,24 hours a day, 7 days a week.

Retain original cash register sales receipt as proof of purchase for warranty work.

Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s).

Deliver or ship the product to the nearest Authorized Warranty Service Center. Freight costs, if any, must be paid by the purchaser.

Air compressors with 60 and 80 gallon tanks will be inspected at the site of installation. Contact the nearest Authorized Warranty Service Center that provides on-siteservice calls, for service call arrangements.

If the purchaser does not receive satisfactory results from the Authorized Warranty Service Center, the purchaser should contact .

THIS WARRANTY DOES NOT COVER:

Merchandise sold as reconditioned, used as rental equipment, and floor or display models.

Merchandise that has become damaged or inoperative because of ordinary wear, misuse*, cold, heat, rain, excessive humidity, freeze damage, use of improper chemicals, negligence, accident, failure to operate the product in accordance with the instructions provided in the Owners Manual(s) supplied with the product, improper maintenance, the use of accessories or attachments not recommended by , or unauthorized repair or alterations.

*An air compressor that pumps air more than 50% during a one hour period is considered misuse because the air compressor is undersized for the required air demand.

Repair and transportation costs of merchandise determined not to be defective.

Costs associated with assembly, required oil, adjustments or other installation and start-upcosts.

Expendable parts or accessories supplied with the product which are expected to become inoperative or unuseable after a reasonable period of use, including but not limited to sanding disks or pads, saw and shear blades, grinding stones, springs, chisels, nozzles, o-rings,air jets, washers and similar accessories.

Merchandise sold by which has been manufactured by and identified as the product of another company, such as gasoline engines. The product manufacturer's warranty, if any, will apply.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS NOT COVERED BY THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

Jackson, TN USA

1-866-422-4286

D27930

18ENG