Delta GR150 User Manual

0 (0)

GR150

6" Bench Grinder with Lamp

Meuleuse d’établi de 152 mm (6 po) avec lampe

Rectificadoras de Banco de 6 pulgadas w/Lámpara

A19595 - 09-01-06

Copyright © 2006 Delta Machinery

Instruction Manual Manuel d’Utilisation Manual de Instrucciones

FRANÇAIS (13)

ESPAÑOL (25-)

 

 

WWW.DELTAMACHINERY.COM

(800) 223-7278 - US

(800) 463-3582 - CANADA

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 2 SAFETY GUIDELINES - DEFINITIONS . . . . . . . . . . 2 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . 3 ADDITIONAL SAFETY RULES . . . . . . . . . . . . . . . . . 4 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . 6 CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . 7 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . 11 MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which

tools and equipment are designed. Delta Machinery strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you. Contact us online at www.deltamachinery.com or by mail at Technical Service Manager, Delta Machinery, 4825 Highway 45 North, Jackson, TN 38305. In Canada,125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.org

National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1 Safety Requirements for Woodworking Machines

U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

CALIFORNIA PROPOSITION 65

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/OSHA approved, properly fitting face mask or respirator when using such tools.

2 - English

GENERAL SAFETY RULES

Failure to follow these rules may result in serious personal injury.

1.FOR YOUR OWN SAFETY, READ THE INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations and specific hazards will greatly minimize the possibility of accidents and injury.

2.WEAR EYE AND HEARING PROTECTION. ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1 standards. Hearing equipment should comply with ANSI S3.19 standards.

3.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts. Nonslip protective footwear is recommended. Wear protective hair covering to contain long hair.

4.DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands and fingers in danger.

5.MAINTAIN ALL TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.

6.CHECK FOR DAMAGED PARTS. Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced with Delta or factory authorized replacement parts. Damaged parts can cause further damage to the machine and/or injury.

7.KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

8.KEEP CHILDREN AND VISITORS AWAY. Your shop is a potentially dangerous environment. Children and visitors can be injured.

9.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the "OFF" position before plugging in the power cord. In the event of a power failure, move the switch to the "OFF" position. An accidental start-up can cause injury. Do not touch the plug’s metal prongs when unplugging or plugging in the cord.

10.USE THE GUARDS. Check to see that all guards are in place, secured and working correctly to prevent injury.

11.REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

12.USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a job for which it was not designed. Damage to the machine and/or injury may result.

13.USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause damage to the machine or injury to the user.

14.USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the "Extension Cord Chart" for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

15.SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.

16.FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed.

17.DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18.DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury.

19.NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool.

20.NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured.

21.TURN THE MACHINE "OFF", AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, changing cutters, adjusting or changing set-ups. When making repairs, be sure to lock the start switch in the "OFF" position. An accidental start-up can cause injury.

22.MAKE YOUR WORKSHOP CHILDPROOF WITH PADLOCKS, MASTER SWITCHES OR BY REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE

COMMON SENSE. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL OR MEDICATION. A moment of inattention while operating power tools may result in injury.

24. USE OF THIS TOOL CAN GENERATE AND

DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS DUST. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

3 - English

ADDITIONAL SAFETY RULES

Failure to follow these rules may result in serious personal injury.

1.DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.

2.OBTAIN ADVICE from your supervisor, instructor or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety.

3.FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution.

4.ALWAYS USE THE PROVIDED BLOTTER AND WHEEL FLANGES to mount the grinding wheels on the grinder shaft to prevent wheel damage or accidental separation. Separation can result in fragments flying off the wheel at high speeds.

5.USE ONLY WHEELS suitable for the speed of the machine. Unsuitable grinding wheels can come apart, throwing fragments out at high speeds.

6.USE ONLY WHEELS that have a bore exactly equal to the arbors of the machine. Never attempt to machine an undersized wheel to fit an arbor. Unsuitable grinding wheels can come apart, throwing fragments out at high speeds.

7.DO NOT OVERTIGHTEN WHEEL NUT.

8.DO NOT USE A WHEEL THAT VIBRATES. Dress the grinding wheel, replace it or replace the bearings of the shaft. Unsuitable grinding wheels can come apart, throwing fragments at high speeds.

9.INSPECT WHEELS before starting the machine for cracks or fragments. REPLACE DAMAGED WHEELS immediately. Parts of the wheel can be thrown at high speeds causing serious injury.

10.ADJUST EYE SHIELDS close to the grinding wheel, and re-adjust as the wheel wears down. Flying sparks are dangerous and can cause fires or explosions.

11.ALWAYS MAKE SURE the eye shields are in place, properly adjusted, and secured.

12.ADJUST TOOL RESTS close to the grinding wheel (1/8" separation or less). Tighten the tool rest securely to prevent shifting positions, and readjust as the wheel wears down. The workpiece can be drawn into the wheel, causing damage to the workpiece and/or serious injury.

13.STAND TO ONE SIDE before turning the machine "ON". Loose fragments or wheel parts could fly from the wheel at high speeds.

14.NEVER GRIND ON A COLD WHEEL. Run the grinder for one full minute before applying the workpiece. A cold wheel has a tendency to chip. Those fragments could fly from the wheel at high speeds.

15.NEVER START THE MACHINE with the workpiece against the grinding wheel. The workpiece can be drawn into the wheel, causing damage to the machine and/or serious injury.

16.CLEAN THE MACHINE thoroughly when processing different types of workpieces (wood, steel or aluminum). Combining wood and metal dust can create an explosion or fire hazard. DO NOT GRIND OR POLISH MAGNESIUM. Fire will result.

17.NEVER GRIND NEAR FLAMMABLE GAS OR LIQUIDS. Sparks can create a fire or an explosion.

18.AVOID AWKWARD OPERATIONS AND HAND POSITIONS. A sudden slip could cause a hand to move into the grinding wheel.

19.KEEP ARMS, HANDS, AND FINGERS away from the wheel. The abrasive surfaces can cause serious injury.

20.HOLD THE WORKPIECE FIRMLY against the tool rest. Loss of control of the workpiece can cause serious injury.

21.DRESS THE WHEEL on the face only. Dressing the side of the wheel could cause it to become too thin for safe use.

22.GRIND A WORKPIECE using the face of the grinding wheel only. Loss of control of the workpiece can cause serious injury.

23.NEVER APPLY COOLANT directly to the grinding wheel. Coolant can weaken the bonding strength of the grinding wheel and cause it to fail. Dip the workpiece in water to cool it.

24.DO NOT TOUCH the ground portion of a workpiece until it has cooled sufficiently. Grinding creates heat.

25.PROPERLY SUPPORT LONG OR WIDE WORKPIECES. Loss of control of the workpiece can cause serious injury.

26.NEVER PERFORM LAYOUT, ASSEMBLY or set-up work on the table/work area when the machine is running. A sudden slip could cause a hand to move into the wheel. Severe injury can result.

27.TURN THE MACHINE "OFF", disconnect the machine from the power source, and clean the table/work area before leaving the machine.

28.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

4 - English

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a time delay fuse. NOTE: Time delay fuses should be marked "D" in Canada and "T" in the US. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the "OFF" position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 120 V., 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the "OFF" position.

GROUNDING INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.

1.All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle.

 

GROUNDED OUTLET BOX

GROUNDED OUTLET BOX

 

 

 

CURRENT

GROUNDING MEANS

 

 

 

CARRYING

 

 

 

 

ADAPTER

 

PRONGS

 

 

 

 

 

 

 

 

 

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A

Fig. B

5 - English

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. C, shows the correct gauge to use

depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

 

 

Total

 

Ampere

 

Length of

 

 

Cord in

Gauge of Extension

 

 

Rating

Volts

Feet

Cord

0-6

120

up to 25

18 AWG

0-6

120

25-50

16 AWG

0-6

120

50-100

16 AWG

0-6

120

100-150

14 AWG

6-10

120

up to 25

18 AWG

6-10

120

25-50

16 AWG

6-10

120

50-100

14 AWG

6-10

120

100-150

12 AWG

10-12

120

up to 25

16 AWG

10-12

120

25-50

16 AWG

10-12

120

50-100

14 AWG

10-12

120

100-150

12 AWG

12-16

120

up to 25

14 AWG

12-16

120

25-50

12 AWG

12-16

120

GREATER THAN 50 FEET NOT RECOMMENDED

 

 

Fig. C

 

FUNCTIONAL DESCRIPTION

FOREWORD

The GR150 is a 6" (152 mm) Bench Grinder. This machine comes with a flexible lamp, adjustable tool rests and two large eye shields for added safety.

NOTICE: The illustration on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only.

6 - English

CARTON CONTENTS

Fig. 1

1

2

 

6

7

 

 

 

3

 

 

 

 

 

 

 

 

8

9

 

 

 

 

 

 

10

 

 

 

 

11

14

 

4

5

12

 

 

 

 

 

13

15

 

1.

Grinder

9.

Right side tool rest with V-groove

2.

Wrench

10.

Eye shield bolt (2)

3.

Eye shield (2)

11.

5/16-18 x 5/8" Hex head screw (2)

4.

Eye shield knob (2)

12.

5/16-18 x 1/2" Hex head screw (2)

5.

Eye shield bushing (2)

13.

1/4-20 x 1/4" Hex head screw (2)

6.

Left side spark guard

14.

3/4" Flat washer (4)

7.

Right side spark guard

15.

1/4" Flat washer (4)

8.

Left side tool rest

 

 

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.

Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine.

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

7 - English

ASSEMBLY

For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.

ASSEMBLY TOOLS REQUIRED

Wrench (supplied)

ASSEMBLY TIME ESTIMATE

Assembly for this machine takes approximately 30 minutes.

TOOL RESTS

Disconnect machine from power source!

1.Assemble the v-grooved tool rest (A) Fig. 2, to the inside of the right wheel guard using two 3/4" flat washers (C), and two 5/16-18 x 5/8" hex head screws (B).

2.Assemble the remaining flat surfaced tool rest (D) Fig. 3, to the inside of the left wheel guard in the same manner using two 3/4" flat washers (C), and two 5/16-18 x 1/2" hex head screws (E).

3.Each tool rest is adjustable so that the edge (F) Fig. 3, of the tool rest can be positioned as close to the grinding wheel (G) as possible giving maximum support to the piece that is being ground. A distance of 1/8" (3.2 mm) or less between the grinding wheel

(G) and the edge (F) of the tool rest should always be maintained. As the grinding wheel wears down to a smaller diameter, re-adjust the tool rest closer to the wheel. The tool rest should be adjusted so it is set a little below the center of the wheel. This is the most practical and safest position for general work. Freehand grinding without the use of the tool rest should always be done on the lower quarter of the wheel.

SPARK GUARDS

Disconnect machine from power source!

Mount the spark guard (A) Fig. 4 to the side of each wheel guard, using the 1/4-20 x 1/4" hex head screw (B) and 1/4" flat washer (C).

NOTE: Place the tab (D) Fig. 4 (on the side of the spark guard) (A) in the slot (E), before attaching the spark guard (A) to the grinder.

Adjust the spark guard (A) as close as possible to the grinding wheel to prevent sparks from striking your hand. As the wheels wear down, adjust the spark guard (A) accordingly.

EYE SHIELDS

Disconnect machine from power source!

Always wear eye protection.

1. Place the eye shield (A) on the spark guard (Fig. 5).

C

A

B

Fig. 2

G

F

C

D

E

Fig. 3

C

B

A D

E

Fig. 4

A

Fig. 5

8 - English

2.Align the holes in the eye shield with the holes in the spark guard. Place the eye shield spacer (A) Fig. 6 in the spark guard.

3.Insert the eye shield bolt (A) Fig. 7 through the eye shield (B), the eye shield spacer (C), and the spark guard (D).

4.Place a 1/4" flat washer (E) Fig. 7 on the end of the eye shield bolt. Fasten the eye shield knob (F) on the end of the eye shield bolt.

5.Assemble the other eye shield in the same manner.

D E

C

F

 

A

A

B

Fig. 6

 

Fig. 7

FASTENING GRINDER TO SUPPORTING SURFACE

Disconnect machine from power source!

 

 

 

If, during operation, there is any

 

 

 

 

 

 

 

 

A

 

 

 

A

 

 

 

 

 

tendency for the grinder to tip over, slide or "Walk",

 

 

 

 

the grinder must be secured to the supporting

 

 

 

surface using fasteners (not supplied) through the

 

 

 

two holes (A) Fig. 8 in the grinder base.

 

 

 

Fig. 8

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING GRINDER

The switch (A) Fig. 9, is located on the front of the grinder. To turn the grinder "ON" move the switch right to the "ON" position. To turn the grinder "OFF" move the switch left to the "OFF" position.

Make sure that the switch is in the "OFF" position before plugging in the power cord. In the event of a power failure, move the switch to the "OFF" position. An accidental start-up can cause

injury.

A

Fig. 9

9 - English

FLEXIBLE LAMP

The flexible lamp operates independently of the grinder.

A

To turn the lamp on and off, rotate switch (A) Fig. 10.

To reduce the risk of fire, use 40 watt or less, 120 volt, reflector track type light bulb (not supplied). A standard household light bulb should not be used. The reflector track type light bulb should not extend below the lamp shade.

GRINDING WHEELS

 

 

 

 

The use of accessories and

 

 

 

 

Fig. 10

attachments not recommended by Delta may result

 

in risk of injuries. Grinding wheels used with this grinder should be rated for 3600 RPM or higher and

be 6" (152 mm) in diameter with a 1/2" (12.7 mm) arbor hole.

Two aluminum oxide grinding wheels are supplied with your grinder; one 36 grit and one 60 grit. For best grinding results, and to maintain good balance, always keep the wheels properly dressed. Do not force the work against a cold wheel. The grinding wheel should always be run at idle speed for one full minute before applying work. It is recommended that only balanced wheels be used with your grinder. The use of balanced wheels adds years to the life of the bearings on the grinder and by eliminating the most common source of vibration, more accurate work is accomplished.

ALWAYS maintain a distance of 1/8" (3.2 mm) or less between the grinding wheel and the tool rest. Adjust the tool rests and spark guards as the grinding wheels decrease in size with use.

DRESSING A GRINDING WHEEL

When dressing a grinding wheel use a suitable silicon (A) carbide stick type dresser (B), as shown in Fig. 11. Move the dresser forward on the tool rest (D) until it touches the high point on the face of the wheel (C). Dress the wheel by moving the dresser back and forth. Repeat this operation until the face of the grinding wheel is clean and the corners of the wheels are square.

ALWAYS maintain a distance of 1/8" or less between the grinding wheel and the tool rest. Adjust the tool rests and spark guards as the grinding wheels decrease in size with use.

A

C

B

D

Fig. 11

CHANGING THE GRINDING WHEELS

Disconnect machine from power source!

1.Remove the screws (A) Fig. 12 and the side covers (B) from the grinding wheel.

2.To prevent shaft rotation, place a wedge between the grinding wheel (C) and the tool rest (D).

NOTE: To remove the left grinding wheel, turn the arbor nut clockwise (toward the front) to loosen. To remove the

right grinding wheel, turn the arbor nut counter-clockwise C (toward the front) to loosen.

3. If the replacement wheel does not require the arbor

 

 

 

bushing, save it for future use.

A

 

B

 

 

 

 

 

 

 

4. To install a new wheel, reverse the procedure.

 

 

 

Do not overtighten the wheel nuts

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when installing

grinding wheels. Tighten the wheel nuts

 

 

 

enough to drive the wheel and prevent slippage.

 

 

 

Fig. 12

 

 

 

 

 

 

 

 

10 - English

Delta GR150 User Manual

MACHINE USE

Keep the spark guards and eye shields in place at all times.

Figures 13, 14, and 15 illustrate several typical operations that can be accomplished using the grinder. Each tool rest should be positioned a little below the center of the grinding wheel and adjusted so that the edge of the tool rest is a distance of 1/8" (3.2 mm) or less from the wheel. This will provide maximum support to the workpiece and is the safest position for general work.

As the grinding wheel wears down, readjust the tool rest closer to the grinding wheel. Always maintain a distance of 1/8" (3.2 mm) or less between the grinding wheel and the edge of the tool rest. Free hand grinding (without the use of the tool rest) should always be done on the lower

quarter of the grinding wheel. Read and follow all of the Fig. 13 "SAFETY RULES" in this manual.

 

 

 

 

 

 

 

 

Fig. 14

 

 

 

Fig. 15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION & RUST PROTECTION

Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.

To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand Pad, a can of WD-40® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad. Degrease the table, then apply the protective product as described above.

11 - English

Loading...
+ 25 hidden pages