Delta Electronics DVP-SS User Manual

Warning

This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation & wiring. Other detail infromation about programming and intructions is compatible with ES series; please see PLC Application Manual. For more information about the optional peripherals, please see individual product instuction shee or “DVP-PLC Application Manual: Special module”.

This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the enclosure, in order to prevent hazard to users or damage the PLC.

Do NOT connect the AC main circuit power supply to any of the input/output terminals, or it may damage the PLC.

Check all the wiring prior to power up. To prevent any electromagnetic noise, make sure the PLC is properly grounded . Do NOT touch terminals when power on.

Introduction

Thank you for choosing Delta DVP-SS series programmable logic controller. DVP-SS provides MPU with 14 points, RUN/STOP switches and 8 ~ 16 points of extension. The maximum I/O points can reach 128 points. DVP-SS can be used for various applications of different I/O points, power types, output modules and A/D, D/A conversion. The power unit is separate from the MPU and is compact in size, plus easy to install.

Product Profile and Outline

13.00 25.20

s s

14

90.00

2

3

4.00

4

5

60.00	6
	7	11
	8
	10	12
	9	13
	3

1. POWER, RUN, ERROR indicator		8. Extension port
2.	I/O port for program communication (RS-232)	9.	Extension unit clip
3.	DIN rail clip	10.	DIN rail (35mm)
4. I/O terminals		11. RS-485 communication port
5.	I/O point indicator	12. Mounting rail for extension unit
6.	Mounting hole for extension unit	13.	DC power input
7. Nameplate		14. RUN/STOP switch

Electrical Specifications
Model		DVP14SS11R/T
Item
Power supply voltage	MPU: 24V DC (-15%~20%) (With DC input reverse polarity protection)
Fuse	2A/250V AC
Power Consumption	3.5W
InsulationResistance	> 5 M	at 500 V DC (Between all inputs / outputs and earth)
	Ω
	ESD: 8KV Air Discharge
Noise Immunity	EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
	Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
	RS: 26MHz ~ 1GHz, 10V/m
Grounding	The diameter of grounding wire cannot be smaller than the wire diameter of
	terminals L and N (All DVP units should be grounded directly to the ground pole).
Environment	Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2;
	Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)
Vibration / Shock Resistance	Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
Weight (approx.) (g)	214(g)/208(g)
Approvals
		Input Point Electrical Specification
Input Type	DC (SINK or SOURCE)
Input Current	24V DC 5mA
	Off → On,
	X0, X1: 18.5V DC and above
Active Level	X2 ~ X7: 16.5V DC and above
	On → Off,
	X0 ~ X7: below 8V DC
Response Time	About 10ms (An adjustment range of 0 ~ 20ms could be selected through D1020 and
	D1021)

			Output Point Electrical Specification
	Output Type		Relay-R			Transistor-T
	Current Specification	1.5A/1 point (5A/COM)			55°C 0.1A/1point, 50°C 0.15A/1point
					45°C 0.2A/1 point, 40°C 0.3A/1 point (2A/COM
	Voltage Specification	Below 250V AC, 30V DC			30V DC
	Maximum Loading	75VA (inductive)			9W/1 point
		90W (resistive)
	Response Time	About 10ms			Off On 20us
					On→Off 30us
	Model Name & I/O Configuration
			Input / Output
	Model	Input Unit		Output Unit		Profilereference	I/O Configuration
	Power	Point	Type	Point	Type
							S/S
	DVP14SS11R2	8		6	Relay		X0
							X2
							X1
							X3
							X4
							X5
			DC Sink or				X6
	24V DC						X7
			Source				Y0
							C0
							C1
	DVP14SS11T2	8		6	Transistor		Y1
							C2
							Y2
							Y3
							Y4
							Y5
	Installation & Wiring
	4.1 PLC Mounting Arrangements and Wiring Notes
	50m m
	50m m DVP MPU 50m m	Please install PLC in an enclosure with sufficient space around it to allow
		heat dissipation as shown in the figure.
	50 mm
	reomro

How to install DIN rail:

DVP-PLC can be secured to a cabinet by using the DIN rail of 35mm in height and 7.5mm in depth. When mounting PLC to DIN rail, be sure to use the end bracket to stop any side-to-side movement of PLC and reduce the chance of wires being loosen. A small retaining clip is at the bottom of PLC. To secure PLC to DIN rail, place the clip onto the rail and gently push it up. To remove it, pull the retaining clip down and gently remove PLC from DIN rail, as shown in the figure.

Wiring:

1. Use the 22-16AWG (1.5mm) single-core bare wire or the multi-core

22-16AWG wire for the I/O wiring, and the specifications of the terminal are shown diagram on the left. The twisting power of the screw for the

PLC terminal is 1.95 kgf-cm (1.7 lb-in).

	2. DO NOT place the input signal cable and output power cable in the
<1.5mm	same wiring circuit.

3. Use only 60/75ºC copper conductor.

4.2 Wiring Notes

Environment

1.DO NOT store the PLC in an atmosphere that is dusty, smoky, with metallic debris or corrosive or flammable gases.

2.DO NOT store the PLC in an environment with high temperature or high humidity.

3.DO NOT install the PLC on a shelf or on an unstable surface.

Power Input Wiring

DVP-SS uses DC input power. Therefore, make sure that DVP-SS is connected to terminals 24V DC and 0V (power range 20.4 ~ 28.8V DC) when the power is ON. DVP-SS will stop the operation and the output will be OFF whenever the power input is lower than 20.4V DC. Consequently, the ERROR LED will blink swiftly.

20.4VDC~28.8VDC

24V DC

OV

+24 V

24 G

S/S

X0

X1

X2

2.5 A

DC/DC 5V

Safety Wiring

Since a PLC controls many devices, actions of any device may affect actions of other devices, and the breakdown of any one device may cause the breakdown of the whole auto-control system and danger. Therefore, we suggest you wire a protection circuit at the power input terminal, as shown in the figure below.

AC power supply load

Power circuit protection fuse (2A)

5

1 Power indicator

	7			4
						Emergency stop
		8				This button can cut off the system power supply when
				Guard	2
				Lim it		accidental emergency takes place.
24V	0V		MC	3	MC	System circuit isolation device
					1	The device is made of electromagnetic contactor and relay
						as the switch to prevent the instability of system when the
						power is intermittently supplied.
24V	0V	L	N			DVPPS01/24V DC power module
				6

DVP-PLC

Power supply: 24V DC

Input Point Wiring

There are two types of DC inputs, SINK and SOURCE.

Two types of DC wiring are used: SINK and SOURCE, defined as follows:

Sink = common port for current input S/S

Source = common port for current output S/S

S/S

X0

Sin k ing

X0

S/S

Sourcing

DC Type

(DC Signal IN)

SINK Mode

DC Type

(DC Signal IN)

SOURCE Mode

Input point loop equivalent circuit

Wiring loop

+24V
24VDC
0V
SINK
+ 5V
+24V	OV	S/S	X0	X1	X2
S/S
24VDC
X0			Sink Type

Input point loop equivalent circuit

Wiring loop

+24 V
	24VDC
0V
	S OURCE
	+5 V
	+24V	0V	S/S	X0	X1	X2
S/ S	24VDC
X0			Source Type

Output Point Wiring

Every output contact possesses a overload capacity that is twice as much as the rated current for 5 minutes. The exceeded range may result in contact malfunction and even the burn-down of internal circuit.

DVP-**-**-11-R			DVP-**-**-11-T
		LOAD			LOAD
		Y0		T	Y0
LED		P OWER			< 0.3A
	RY		LED	R
		C0		G	C0
		RELAYOUTPUT			TRANSISTOR OUTPUT

1.Two types of DVP-SS series PLC output modules: Relay or Transistor. For the electrical specification, please refer to the function specification.

2.Please watch out the connection of common terminals while wire the outputs. For example, when wiring DVP14SS11R, output terminal Y0 uses one common terminal C0, Y1 uses C1, and Y2 ~ Y5 share C2, as shown below:

C0 Y0 C 1 Y1 C2 Y2 Y3 Y4 Y5

Action indication: When the output point is active, the corresponding indicator at the front panel will be on.

3.Isolated circuit: The optical coupler is used to isolate signals between PLC internal circuits and input modules.

ES

DVP-PLC

(OPEN TYPE)

/

(

:

)

/

DVP

DVP-SS

14

RUN/STOP

8 ~ 16

/

128

/

/

A/D

D/A

4

5

1

3.00

25.20

60.00

6

7

11

14

8

10

12

9

90.00 13

2

3

3

4.00

1.

8.

2.

(RS-232)

9.

3. DIN

10. DIN

(35mm)

4.

11. RS-485

5.

12.

6.

13.

7.

14. RUN/STOP

DVP14SS11R/T

24V DC (-15% ~ 20%)

5ms

2A/250V AC

3.5W

5 M

500V DC

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Analog &

Communication I/O: 1KV

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

L, N

PLC

0°C ~ 55°C

50 ~ 95%

2

-40°C ~ 70°C

5 ~ 95%

IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

,g

214 (g)/208 (g)

SINK

SOURCE

24VDC 5mA

Off → On,

X0

X1

18.5V DC

X2 ~ X7

16.5V DC

On → Off,

X0 ~ X7

8V DC

10 ms

D1020

D1021

0 ~ 20ms

-R

-T

55°C 0.1A/1

50°C 0.15A/1

1.5A/1

5A/COM

45°C 0.2A/1

40°C 0.3A/1

2A/COM

250VAC,30VDC

30V DC

75VA

9W/1

90 W

10 ms

Off → On 15us

On → Off 25us