DE’LONGHI
COOKING
INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
DEIND603
DEIND604
DEIND804
INDUCTION BUILT-IN COOKTOPS
distributed by
DeLonghi Australia Pty Ltd
DeLonghi New Zealand Ltd
Dear Customer,
Thank you for having purchased and given your preference to our product.
The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance.
Please keep this booklet in a safe place. It may be useful in future, either to yourself or to others in the event that doubts should arise relating to its operation.
This appliance must be used only for the task it has explicitly been designed for, that is for cooking foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the event of damage caused by improper, incorrect or illogical use of the appliance or be faulty installation.
Important:
This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. a semi commercial, commercial or communal environment.
This appliance has been designed and constructed in accordance with the following codes and specifications:
AS/NZS 60335.1 General Requirements for Domestic electrical appliances
AS/NZS 60335.2.6 Particular Requirements for Domestic electrical cooking appliances AS/NZS CISPR 14.1 Electromagnetic Compatibility Requirements.
PRODUCT LABEL
2
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental rules. In particular:
■■ Never touch the appliance with wet hands or feet.
■■ Do not operate the appliance barefooted.
■■ The appliance is not intended for use by young children or infirm persons without supervision.
■■ Young children should be supervised to ensure they do not play with the appliance.
The manufacturer cannot be held responsible for any damages caused by improper, incorrect or illogical use of the appliance.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be left around within easy reach of children, as these may cause serious injuries.
■■ Read the instructions carefully before installing and using the appliance.
■■ The appliance should be installed and all the electrical connections made by a qualified engineer in compliance with local regulations in force and following the manufacturer’s instructions.
■■ Do not attempt to modify the technical characteristics of the appliance as this may become dangerous to use.
■■ Do not carry out cleaning or maintenance operations on the appliance without having previously disconnected it from the electric power supply.
■■ After use, ensure that the controls are switched off.
■■ Keep children away from the appliance when it is in use.
3
■■ WARNING: Accessible parts will become hot when in use. To avoid burns and scalds, young children should be kept away.
■■ Young children should be supervised to ensure that they do not play with the appliance.
■■ Children, or persons with a disability which limits their ability to use the appliance, should have a responsible person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to themselves or their surroundings.
■■ During and after use of the appliance, certain parts will become hot. Do not touch hot parts.
■■ Make sure that electrical cables connecting other appliances in the proximity of the cooktop cannot come into contact with the hob.
■■ Do not allow heavy or sharp objects to drop on the glass ceramic hob. If the hob is cracked or otherwise damaged by falling objects etc., disconnect the electrical power cord and call Customer Service.
■■ Do not scratch the hob with sharp objects. Don’t use the hob as a work surface.
■■ WARNING: When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the underneath of the appliance as this area is not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.
■■ Fire risk! Do not store flammable material on the hob top.
■■ The manufacturer declines all liability for injury to persons or damage to property caused by incorrect or improper use of the appliance.
■■ IMPORTANT NOTE: This appliance shall not be used as a space heater, especially if installed in marine craft or caravans.
■■ Do not operate your appliance by means of an external timer or separate remote-control system.
■■ This appliance is for domestic use only.
■■ If the supply cord (not supplied with the appliance) is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
4
OTHER IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
■■ Do not place or leave empty pans on the glass ceramic hob.
■■ Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
■■ Do not use metallic kitchen utensils (e.g. ladles). It is preferable to use plastic or wood kitchen utensils.
■■ Please use pans of recommended size (see minimum pan diameter recommended). It is not advisable to use pans smaller than the cooking zone. The pans have to be placed in the centre of the cooking zone.
■■ Do not use defective pans or pans with a curved bottom. ■■ Please use suitable pans marked for induction cooking.
■■ Please keep your distance from the electromagnetic fields by standing 5-10 cm from the cooking zones. When possible use the rear cooking zones.
■■ Magnetic objects (e.g. credit cards, floppy disks, memory cards) and electronic instruments (e.g. computers, MP3 players) should not be placed near the appliance, as they may be affected by its electromagnetic field.
■■ The heating of magnetic tins is forbidden! Close tins may explode by exceeding pressure while heating. There is a burning risk with open tins as well, because the integrated temperature protection can’t work well.
■■ HEALTH HAZARD! This appliance complies with electromagnetic safety standards. However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor or implant manufacturer before using this appliance to make sure that their implants will not be affected by the electromagnetic field.
Failure to follow this advice may result in death.
5
INSTALLATION
CAUTION:
■■ This appliance must be installed in accordance with these installation instructions. ■■ This appliance shall only be serviced by authorised personnel.
■■ This appliance is to be installed only by an authorised person in compliance with the current electrical regulations and in observation of the instructions supplied by the manufacturer.
Failure to comply with this condition will render the guarantee invalid.
■■ Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury of damage.
■■ Always disconnect the appliance from mains power supply before carrying out any maintenance operations or repairs.
FITTING REQUIREMENTS
This cooktop can be built into a working surface 30 to 40 mm thick and 600 mm deep.
In order to install the ceramic hob into the kitchen fixture, a hole with the dimensions shown in figure 1 has to be made, keeping in consideration the following:
■■ The cooktop shall not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the humidity may damage the cooktop electronics.
■■ If the cooktop is installed above an oven, the oven shall be provided with cooling fan. The two appliances should be connected to the electrical supply with independent connections.
■■ IMPORTANT WARNING! This cooktop requires adequate supply of fresh, cool air to fully function. The base of the cooktop must have direct unrestricted ventilation to the room where the cooktop is installed. Follow the requirements of figure 3 or 4.
■■ There must be a distance of at least 650 mm between the hob and any wall cupboard or extractor hood positioned immediately above (see fig. 2).
■■ We would point out that the adhesive which bonds the plastic laminate to the furniture must withstand temperatures not less than 150° C to avoid delamination.
■■ The walls of the units must be capable of resisting temperatures of 75 °C above room temperature.
■■ Do not seal the cooktop into the benchtop with silicone or glue; this makes future servicing difficult. Delonghi will not cover the costs of removing the cooktop, or of damage caused by this removal.
■■ The walls surrounding the cooktop must be made of heat-resistant material.
■■ Do not install the appliance near inflammable materials (eg. curtains).
WARNING
When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the underneath of the appliance as this area is not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.
6
Figure 1
A 
550
A 
550
580 |
Mod. DEIND603 |
|
|
|
(1) |
|
50 |
|
480 |
580 |
Mod. DEIND604 |
|
|
|
(1) |
|
50 |
|
480 |
510
A 
730
770
Mod. DEIND804
(1) 50
480
from the top of A 58 mm countertop to
bottom of cooktop
(1)at least 50 mm between the back side of the cut-out and
the back of the countertop.
7
Figure 2
450 mm |
650 mm |
500 |
mm |
|
70 mm minimum between the side of the cut-out and the side wall
Figure 3
25 mm |
min 5 mm |
|
Oven with |
||
min |
||
cooling fan |
||
|
min 30 mm |
|
|
Minimum clearances and |
|
|
ventilation requirements |
|
|
(oven installed below) |
|
8 |
|
Figure 4
min 25 mm |
min 5 mm |
|
|
|
min 30 mm |
|
Minimum clearances and |
|
ventilation requirements |
|
(cupboard or drawer space below) |
FASTENING THE COOKTOP
Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to benches from 30 to 40 mm thick.
The kit includes four “F” brackets and four self-threading screws “S” (fig. 6). ■■ Cut the unit according to the dimensions in fig. 1.
■■ Turn the hob upside down and rest the glass side on a soft surface.
■■ Spread the seal “G” around the edge of the hob (fig. 5).
■■ Fasten the brackets “F” to the appropriate socket holes, without tightening the screws “S” for the moment. Make sure that the tabs are mounted correctly, as shown. Rotate the tabs so that the cooktop can be put into the cutout.
■■ Put the cooktop into the cutout and position it correctly.
■■ Put the brackets “F” into place; tooth “A” of the brackets should go into the hole (fig. 6). ■■ Tighten screws “S” until the cooktop is completely secured to the bench.
■■ Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the cooktop. Take care not to damage the workbench.
Figure 5
|
G |
G |
Adhesive side |
Figure 6
|
A |
3 cm |
4 cm |
|
|
|
|
253 cmmm min |
S |
F |
|
|
|
|
9 |
ELECTRICAL REQUIREMENTS
■■ The appliance must be connected to the mains checking that the voltage corresponds to the value given in the rating plate and that the electrical cable sections can withstand the load specified on the plate.
■■ A suitable isolating switch providing full disconnection from the mains power supply shall be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements).
■■ The isolating switch shall be easily accessible to the customer with the cooktop installed.
■■ The power supply cable must not touch the hot parts and must be positioned so that it does not exceed 75°C above ambient.
■■ To connect the appliance to the mains electricity supply, do not use adapters, reducers or branching devices as they can cause overheating and burning.
N.B. The connection of the appliance to earth is mandatory.
If the installation requires alterations to the domestic electrical system call a qualified electrician. He should also check that the domestic electrical system is suitable for the power drawn by the appliance.
Replacing the power cord (not supplied with the appliance) must be done by a qualified electrician in accordance with the instructions supplied by the manufacturer and in compliance with established electrical regulations.
CONNECTION OF THE POWER SUPPLY CABLE
Important! This cooktop must be connected to the electricity supply only by an authorised person.
To connect the feeder cable to the hob it is necessary to carry out the following operations:
■■ Unhook the terminal board cover “A” by inserting a screwdriver into the two hooks “B”
(fig. 7). Open completely the terminal block cover “A”.
■■ Unscrew the screw “C”, then unhook the cable clamp “D” by inserting a screwdriver into the hook “E”. Remove completely the cable clamp “D” (fig. 7).
■■ Connect the phase, neutral and earth wires to terminal board “F” according to the diagrams in fig. 8; the U bolts “G” (fig. 7) shall be used as indicated in the diagrams in fig. 8 (they are supplied already fitted to the terminals or inside the terminal board, behind the cover).
■■ Strain the feeder cable and block it with cable clamp “D” (by hooking hook “E” and screwing screw “C”).
■■ Close the cover “A” of the terminal board “F” (check the two hooks “B” are correctly hooked).
VOLTAGE AND POWER CONSUMPTION
Mod. DEIND603 |
|
|
|
|
220-240/380-415 V 3N~ |
50/60 Hz |
6700 W |
29.13 A |
(diversity not applied) |
Mod. DEIND604 - DEIND804 |
|
|
|
|
220-240/380-415 V 3N~ |
50/60 Hz |
7400 W |
32.17 A |
(diversity not applied) |
10
Loading...