Daewoo DWC-ED1232 User Manual

0 (0)

Washing Machine Instruction Manual

DWC-ED1232

INSTRUCTION MANUAL

Economic wash system

Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water lever and washing time.

Low noise system

The washer minimizes the washing and spinning noises by sensing the amount of laundry.

Child-Lock

The Child-Lock system has been used to prevent children from pressing any button to change the program during operation.

Nano-silver sterilization washing(Option)

By applying very fine silver particles on essential parts inside, the washer sterilizes up to 99.9% as is done by boiling wash.

Air bubble washing(Option)

This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.

CONTENTS

Page

PARTS AND FEATURES.................................................................................................................

2

WASHER SAFETY...........................................................................................................................

3

INSTALLATION INSTRUCTIONS ....................................................................................................

4

INLET HOSE CONNECTION ...........................................................................................................

5

ELECTRICAL REQUIREMENTS .....................................................................................................

6

OPERATING YOUR WASHER ........................................................................................................

7

THE FUNCTIONS OF THE CONTROL PANEL...............................................................................

9

WASHING PROGRAM...................................................................................................................

11

WASHING PROCEDURE AND SELECTION ................................................................................

12

GUIDE FOR OTHER USEFUL PROGRAMS.................................................................................

23

MAINTENANCE .............................................................................................................................

27

HOW TO CLEAN THE FILTER ......................................................................................................

28

REMOVING STAINS ......................................................................................................................

29

TROUBLE SHOOTING ..................................................................................................................

30

SPECIFICATION ............................................................................................................................

31

A NOTE TO YOU

 

Thank you for buying a DAEWOO appliance.

 

DAEWOO washers are easy to use, save time, and help you manage your home better.

 

This manual contains valuable information about how to operate and maintain your washer property and safely.

 

Please read it carefully.

 

PARTS AND FEATURES

The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer.

NOTE

The drawings in the book may vary from your washer model.

They are designed to show the different features of all models coverd by this book, Your model may not include all features.

INLET HOSE

INLET HOSE

(HOT, OPTION)

(COLD)

DETERGENT CASE

POWER CORD

CONTROL PANEL

DOOR

HOSE DRAIN

PUMP COVER

ADJUSTABLE LEG

PANEL LOWER

Accessories

Hose drain

Inlet hose

Spanner

Manual

Cap holder(4EA)

2

WASHER SAFETY

Save these instructions

Your safety is important to us.

To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions.

Read all instructions before using your washer

Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer.

Do not add flammable fluids to your wash water.These substances give off vapors that can create a fire hazard or explosion.

After starting a cycle, do not reach into the washer until all motions stop.

Do not tamper with the controls.

The appliance is not intended for use by young children or infirm persons without supervision.

If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent or a similarly qualified person in order to avoid a hazard.

If the appliance is supplied from a cord extension set or electrical portable outlet device it should be positioned so that it is not subjected to splashing or ingress of moisture.

Please ...

Have only a qualified person install, repair, or replace parts on washer.

Maintain washer properly.

Protect washer from the weather and keep it where the temperature will not fall below freezing.

Do not install the washer at a place of extremely high humidity. It could cause an electric shock or a short circuit.

Connect washer to the correct outlet, electrical supply, water supply, and drain supply.

Door will not open in case of high temperature inside tub.

Prevent children from entering machine.

Understanding your responsibilities

Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash. Hazardous fumes can form.

Unplug power supply cord before attempting to service your washer.

Do not wash fiberglass material.

Small particles can stick to fabrics washed in following loads and cause skin irritation.

Do not spray water on the control panel of the washer. It could cause fire or an electric shock.

In case of the dual valve model, if you connect only cold water inlet valve, while water temperature is selected as hot or warm, there can be water leakage from unconnected water inlet valve.

This appliance must be grounded.

To avoide electrical shock, use a metal pipe for the ground connection.

3

Drain Hose

INSTALLATION INSTRUCTIONS

Removing transit bolts

1.Before operating the washer, remove the transit bolts(4ea) along with the rubber.

If the bolts are not removed, it may cause heavy vibration, noise and malfunction.

3. Close the holes with the cap holders supplied.

2.Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use.

Whenever the appliance is transported, the transit bolts must be refitted.

Location of washer

• Check location where the washer will be installed. Make sure you have everything necessary for correct installation.

• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.

• Do not place or store laundry products on top of washer at any times.

• Install the washer on the horizontal solid floor.

If the washer is installed on an unsuitable floor, it could make

Washer

 

considerable noise, vibrate severely and cause a malfunction. If the

 

washer is not level, adjust leg up or down for horizontal installation.

 

• Ventilation openings must not be obstructed by carpeting when the

Laundry

washer is installed on a carpeted floor.

• Leave some space (right & left : 2cm, rear : 10cm).

Tub

approx.

• In case of built-in installation, the distance between top of the washer

2cm

and bottom of upper plate should be at least 3mm.

 

4

INLET HOSE CONNECTION

The washer should be connected to the water mains using new hose sets and old hose sets should not be reused.

In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve.

Option : Be careful not to confuse hot water inlet and cold water inlet.

For Ordinary Tap

1Pull down the collar of the

2Loosen the four screws

3Fit the water tap adapter

inlet hose to separate it

properly in order to fit into

into the water tap and

from the water tap

water tap.

tighten the four screws

adapter.

 

evenly while pushing up

 

 

the adapter so that the

 

 

rubber packing can stick

 

 

to the water tap tightly.

 

 

TAPE

4Remove the tape, and

5Connect the inlet hose to

6Connect the inlet hose

screw connector B into

the water tap adapter by

adapter of the hose to the

connect A tightly.

pulling down the collar of

water inlet of the washer

 

the hose end.

by turning it clockwise to

 

 

be fixed tightly.

Connector A

Connector B

For Screw-Shaped Tap

1Connect the inlet hose to the water tap by screwing the connector tightly.

Rubber

Connector Packing

Hose Connector

2Connect the connector inlet supplied if necessary.

Connector

inlet

Rubber

Connector Packing

Hose Connector

inlet of a washer and turn it to be fixed.

*Check the

inlet

5

ELECTRICAL REQUIREMENTS

WARNING

Electrical shock hazard : Failure to follow these instructions could result in

death or serious injury.

 

 

 

Electrical earth is required on this washer

If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

Don’t earth to a gas pipe.

Don’t change the power supply cord plug.

Check with a qualified electrician if you are not sure the washer is properly earthed.

Recommended earthing method

C

B

A

For your personal safety, this washer must be earthed.

This washer is equipped with a power supply cord ‘A’ having a earthing plug ‘B’. To minimize possible shock hazard, the cord must be plugged into a mating earthing-type wall receptacle ‘C’. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have the proper earthed wall receptacle installed by a qualified electrician.

Drain system

Never forget to install drain hose before operating your washer.

Open the packing box, and there is a drain hose inside the drum.

Connect the drain hose to the drain outlet at the back side of the washer.

Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.

When installing the drain hose to tub(sink), secure it tightly with a string.

Proper securing of the drain hose will protect the floor from damage due to water leakage.

When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.

Level adjustment

1If the washer is installed on an unsuitable floor, it could make considerable noise, vibrate and cause a malfunction.

6

2Adjust the level of washer using adjustable legs.

Please check if there is any gap between the four adjustable legs and the floor.

Turning adjustable legs by the enclosed

spanner, adjust the level of washer and make

it sure that there is no swaying of washer.

Fixing Nut

 

• After the adjustment is finished, turn the fixing

adjustable leg

nuts up tightly so that the washer maintains

 

the adjustment.

 

3Make it sure that the washer does not sway when you press down the four corners of the washer's top plate.

NOTE

There should be no swaying of washer and all the adjustable legs should stick to the floor closely.

OPERATING YOUR WASHER

To obtain the best washing results, you must operate your washer properly. This section gives you this important information.

Preparing clothes for washing

Close zippers, snaps, and hooks to avoid snagging other items.

Remove pin, buckles, and other hard objects to avoid scratching the washer interior.

Empty pockets and pull them inside out.

Turn down cuffs and turn synthetic knits inside out to avoid pilling.

Tie strings and sashes to avoid tangling.

Treat spots and stains.

(See “Removing stains” on page 21)

7

Sorting

Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.

Separate dark colors from light colors, colorfast items from non-colorfast item.

Soil (Heavy, Normal, Light) Color (White, Lignts, Darks) Lint (Lint producers, Collectors)

Separate clothes according to amount of soil. Separate white clothes from colored clothes. Wash lint producers and lint collectors separately.

Loading

Drop items into washer loosely. Items should move easily through wash water for

best cleaning and

-free results.

Load washer properly and select correct load size setting.

Overloading and selecting a setting too small for the wash load can :

-Cause poor cleaning

-Increase wrinkling

-Create excessive lint

-Wear out items faster (because of pilling)

Mix large and small items in each load. Load evenly to maintain washer balance.

An unbalanced load can make the washer vibrate during spin.

Reduce wash time when using a small load size setting. Load with only a few small items needs less wash time.

Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items. (towels, jeans)

Adding detergent

1Detergent case

Pre wash

Main wash

Fabric softener

2Adding fabric softener

If desired, add measured liquid fabric softener to the softener inlet.

Pour liquid fabric softener into the dispenser using the amount recommended on the package.

Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes.

Do not open the detergent case when water is supplied.

Avoid pouring fabric softener directly on the clothes.

8

Daewoo DWC-ED1232 User Manual

THE FUNCTION OF CONTROL PANEL

Press this switch to turn the power 'ON' or 'OFF'.

Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the 'Start/Pause' button→ Select the program that you want to change → Press the 'Start/Pause' button again.

You can select the course you want and each lamp is turned on when that course is selected.

You can select the wash course you want and each lamp is turned on when that course is selected. As this button is pressed, the wash course is selected by 'Quick Wash'(proper load amount :1~2kg)→ 'Small'(proper load amount :2~3kg)→ 'Main Wash'→ 'Pre Wash'→ 'Soak'→ 'Quick Wash' .

You can select the rinse time(s) you want and each lamp is turned on when that course is selected. As this button is pressed, the rinse time(s) is selected by '1'→ 'Rinse Hold'→ '2'→ 'Rinse Hold' →... ...→ '5'→ 'Rinse Hold'→ '1'.

You can select the spin speed you want and each lamp is turned on when that course is selected.

It can be used to pre-engage time for wash from 1 hr to 12 hrs.

It can be used to adjust water temperature according to types of the load to be washed.

As this button is pressed, water temperature is selected by Cold → 30°C → 40°C → 60°C → 95°C.

You can select the dry condition you want and each lamp is turned on when that course is selected.

Use this function when you want to protect any accident occurring from handling of washer by a child. During an operation of washer, press 'TEMP' and 'DRY' buttons simultaneously during 3 second. If this mode will be set successfully, CHL and remain time will be showen on PCB board alternately.

In Child Lock mode, no button functions except Power button.

If you want to set this mode, press 'TEMP' and 'DRY' buttons simultaneously during 3 second.

And if you want to release this mode, press 'TEMP' and 'DRY' buttons simultaneously again during 3 second.

If you want to change to the desire program, while this mode is working;

1.Press 'TEMP' and 'DRY' buttons simultaneously again during 3 second.

2.Press the 'Start/Pause' button.

3.Select the desired program and press the 'Start/Pause' buttom again.

Change the desired program

* The Child Lock will be

when power is off.

If you want to open Door intensionally during operation, press the 'Start/Pause' button and press again 'Door unlock' button.

In this case, signal will be appeared on PCB board, then you can open Door after cooling insideTub temperature and draining water, also no button functions except Power button.

9

Loading...
+ 21 hidden pages