Dacor PRV36, PRV30, ERV48-ER, ERV36-ER, ERV48 User Manual

ERV3015, ERV3615, ERV36-ER, ERV48, ERV48-ER,

Document # PG08-001

PRV30, PRV36, PRV48

Revised 02/28/14 Page 1/7

Renaissance® Slim Chassis

PLANNING

Downdraft Vents

GUIDE

Dimensions - models ERV3015, ERV3615

warning

2 3/16”

•

Observe all governing codes and ordinances

(5.6 cm)

during planning and installation. Contact your

5/16” (8 mm)

2 1/8”

local building department for further information.

Top cap with

thick stiffener

(5.4 cm)

vent down

•

This appliance must be installed in accordance

across back

with the accompanying installation instructions.

3/16”

(5 mm)

3”

(7.6 cm)

9/16”

All tolerances: ±1/16” (±1.6 mm)

(1.4 cm)

unless otherwise stated

* Total chassis depth with

1 15/16”

optional CABP3 blower

(4.9 cm)

2 9/16”*

installed is 10 3/8” (26.3 cm).

(6.5 cm)

A

Vent shown

15"

(38.1 cm)

in raised

position

3/8”

(1.0 cm)

2 1/8” (5.4 cm)

Top cap - side view

20”

(50.8 cm)

3 3/4”

(9.5 cm)

1 1/8”

(2.9 cm)

		B	Product
			data label
30 1/4”	30"	6”
	(76.2 cm)
(76.8 cm)		(15.2 cm)
to		Motor
37 1/4”
		cover
(94.6 cm)			28" 3 prong
		Front of unit	grounded
			power cord
		Adjustable
		anchor legs

Side View

	Model No.	A	B	Circuit
				Requirement**
	ERV3015	30”	27 3/8”	Three prong electri-
		(76.2 cm)	(69.5 cm)	cal outlet connected
				to 120 Vac, 60 Hz.,
		36”	33 3/8"
	ERV3615			15 Amp. grounded,
		(91.4 cm)	84.8 cm)
				dedicated, circuit
	** Includes power supply requirements for blower

Front View

NOTES:

1.Maximum installed height must not exceed the maximum specified countertop height of cooking appliance.

2.Install these downdraft vents only with approved Dacor appliances. See the planning guide for the particular appliance for proper applications and cutout information.

3.This appliance must be install in conjunction with a single, Dacor approved blower. See page 4/7 for approved blowers.

4.Local building codes may require the use of makeup air systems. Consult a qualified HVAC specialist when designing the system for the requirements in your area and to assure optimal performance.

All specifications subject to change without notice.

www.dacor.com

Phone: [phone]

ERV3015, ERV3615, ERV36-ER, ERV48, ERV48-ER,

Document # PG08-001

PRV30, PRV36, PRV48

Revised 02/28/14 Page 2/7

Renaissance Slim Chassis

PLANNING

Downdraft Vents

GUIDE

Dimensions - models ERV48, PRV30, prv36, PRV48

warning

• Observe all governing codes and ordinances

during planning and installation. Contact your

local building department for further information.

• This appliance must be installed in accordance

with the accompanying installation instructions.

All tolerances: ±1/16” (±1.6 mm)

unless otherwise stated

3/8" (1.0 cm)

A						2 1/8" (5.4 cm)
			ERV top cap - side view

7/16"

(1.1 cm) 2 1/8" (5.4 cm)

PRV top cap - side view

B

Side View

	Model No.	A	B	Circuit
				Requirement**
	PRV30	30”	27 3/8”
		(76.2 cm)	(69.5 cm)
	PRV36	36”	33 3/8”	Three prong electri-
		(91.4 cm)	84.8 cm)	cal outlet connected
				to 120 Vac, 60 Hz,
		46”	43 3/8”
	PRV46			15 Amp. grounded,
		(116.8 cm)	(110.2 cm)
				dedicated, circuit
	ERV48	48”	43 3/8”
		(121.9 cm)	(110.2 cm)

** Includes power supply requirements for external blower

Front View

NOTES:

1.Maximum installed height must not exceed the maximum specified countertop height of cooking appliance.

2.Install these downdraft vents only with approved Dacor appliances. See the planning guide for the particular appliance for proper applications and cutout information.

3.This appliance must be install in conjunction with a single Dacor approved blower. See page 4/7 for approved blowers.

4.Local building codes may require the use of makeup air systems. Consult a qualified HVAC specialist when designing the system for the requirements in your area and to assure optimal performance.

All specifications subject to change without notice.

www.dacor.com

Phone: [phone]

ERV3015, ERV3615, ERV36-ER, ERV48, ERV48-ER,

Document # PG08-001	PRV30, PRV36, PRV48	Revised 02/28/14 Page 3/7
	Renaissance Slim Chassis	PLANNING
	Downdraft Vents	GUIDE

Dimensions - models ERV36-er, ERV48-er

1/4"

5/16” (8 mm)

(6 mm)

thick stiffener

2 13/16"

across back

(7.1 cm)

2 1/2"

Top cap with

(6.4 cm)

vent down

1 15/16"

(4.9 cm)

2 9/16"

(6.5 cm)

warning

•Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information.

•This appliance must be installed in accordance with the accompanying installation instructions.

All tolerances: +/- 1/16” (+/- 1.6 mm) unless otherwise stated

Model Number	A	B
ERV36-ER	36” (91.4 cm)	33 3/8” (84.8 cm)
ERV48-ER	48” (121.9 cm)	43 3/8” (110.2 cm)

NOTE: See the appliance planning guide page for cutout dimensions

A

Vent shown

in raised

10"

position

(25.4 cm)

18 5/8”

(47.3 cm)

3 3/4"

(9.5 cm)

1"

(2.5 cm)

		B	Product
			data label
30 ¼"	30"	6"
	(76.2 cm)
(76.8 cm)		(15.2 cm)
to		Motor
37 ¼"
		cover
(94.6 cm)			28" 3 prong
			grounded
		Front of unit	power cord
		Adjustable
		anchor legs

NOTES:

1.Maximum installed height must not exceed the maximum specified countertop height of cooking appliance.

2.Install these downdraft vents only with approved Dacor appliances. See the planning guide for the particular appliance for proper applications and cutout information.

3.This appliance must be install in conjunction with a single Dacor approved blower. See page 4/7 for approved blowers.

4.Local building codes may require the use of makeup air systems. Consult a qualified HVAC specialist when designing the system for the requirements in your area and to assure optimal performance.

Circuit Requirement (all models)*

Three prong electrical outlet connected to 120 Vac, 60 Hz, 15 Amp. grounded, dedicated, circuit

* Includes power supply requirements for external blower.

All specifications subject to change without notice.

www.dacor.com

Phone: [phone]