Cub Cadet SC2400 User Manual

4 (1)

INTRODUCTION

Welcome to the World of Cub Cadet Yanmar Tractor

Thank you for purchasing our tractor product that has been designed and manufactured based on our state-of-the-art technology and rich expertise in developing and manufacturing tractor products.

Handle your tractor correctly by following the instructions contained in this Operator’s Manual so that it provides you long years of reliable and faithful service.

This manual constitutes an indispensable part of your Cub Cadet Yanmar tractor product. Always keep the manual readily accessible.

Carefully study this manual to get familiar with the instructions and information contained in it. These instructions and information are helpful in using your tractor correctly and safely, and avoiding personal injury and other accidents during operation and servicing of the tractor.

When using any implement together with your tractor, also carefully study its operation manual so that you can use it safely, correctly and efficiently.

This manual is organized with sections arranged in a particular order so that you can better understand the safety messages and the controls on your tractor to help you operate your tractor correctly and safely. This manual will also help you answer questions about operation and servicing. An index is available at the end of this manual to assist you in quickly finding necessary information.

The machine shown in this manual may somewhat differ from your actual machine. However, this manual will still assist you in understanding the instructions associated with your tractor.

Before delivery of your machine, your Cub Cadet Yanmar dealer has performed a pre-delivery check to ensure that your tractor can long remain problem-free.

1

Sc2400 Operator’s Manual

TABLE OF CONTENTS

...................................................................................1. SAFETY PRECAUTIONS

1-1

1.

About This Manual ..................................................................................................................

1-1

2.

Safety-Alert Symbols...............................................................................................................

1-2

3.

Precautions before Operating Your Tractor ............................................................................

1-3

4.

Safe Practices for Operating Your Tractor ..............................................................................

1-4

5.

Operating Your Tractor on Slopes...........................................................................................

1-6

6.

Traveling on a Road ................................................................................................................

1-7

7.

Safe Practices for Parking Your Tractor..................................................................................

1-7

8.

Operating the Power Take Off (PTO)......................................................................................

1-8

9.

Using the 3-Point Hitch............................................................................................................

1-8

10.Safety Frame (Roll-Over Protective Structure) (ROPS) Precautions ......................................

1-8

11.Safe Practices for Servicing Your Tractor ...............................................................................

1-9

12.Understanding the Tractor Safety Decals .............................................................................

1-11

 

Safety-Alert Symbols ...........................................................................................................................................

1-11

 

Care of DANGER, WARNING and CAUTION Decals.........................................................................................

1-11

 

 

2. SERVICING THE TRACTOR ..............................................................................

2-1

 

 

3. SPECIFICATIONS...............................................................................................

3-1

1.

Specifications Table ................................................................................................................

3-1

2.

Traveling Speeds ....................................................................................................................

3-2

 

 

4. IMPLEMENT CAPACITIES.................................................................................

4-1

 

 

5. NAMES AND FUNCTIONS OF COMPONENTS ................................................

5-1

1.

Appearance .............................................................................................................................

5-1

2.

Operator Station Controls........................................................................................................

5-2

3.

Instrument Panel, Switches and Hand Controls......................................................................

5-3

 

 

6. PRE-OPERATION CHECK .................................................................................

6-1

1.

Pre-Operation Check...............................................................................................................

6-1

2.

Precautions before the Operation ...........................................................................................

6-1

3.

Routine Check.........................................................................................................................

6-1

4.

Prevent Damage to the Plastic Surfaces and Painted Surfaces .............................................

6-1

 

 

7. OPERATING THE ENGINE ................................................................................

7-1

1.

Starting the Engine..................................................................................................................

7-1

 

Opening / Closing the Fuel Shut-Off Valve............................................................................................................

7-1

 

Adjusting the Operator's Seat................................................................................................................................

7-2

 

Fastening the Retractable Seat Belt......................................................................................................................

7-2

 

Engaging the Parking Brake..................................................................................................................................

7-3

 

Checking the Lights on the Instrument Panel........................................................................................................

7-6

 

Warming Up the Engine in Cold Weather..............................................................................................................

7-7

2.

Stopping the Engine ................................................................................................................

7-8

3.

Restarting a Stalled Engine.....................................................................................................

7-9

Sc2400 Operator’s Manual

2

 

TABLE OF CONTENTS

 

 

8. OPERATING THE TRACTOR.............................................................................

8-1

1.

Operating a New Tractor .........................................................................................................

8-2

2.

Operation of the Tractor ..........................................................................................................

8-3

 

Turn Signals ..........................................................................................................................................................

8-3

 

Headlights / Work Lights........................................................................................................................................

8-3

 

Hazard Lights ........................................................................................................................................................

8-3

 

Range Shift Lever..................................................................................................................................................

8-4

 

4-Wheel Drive Lever..............................................................................................................................................

8-4

 

Throttle Control Lever............................................................................................................................................

8-5

 

Forward and Reverse Drive Pedal ........................................................................................................................

8-6

 

Engaging the Cruise Control .................................................................................................................................

8-7

 

Disengaging the Cruise Control.............................................................................................................................

8-7

3.

Stopping Travel of the Tractor.................................................................................................

8-8

 

Emergency Stop Procedure ..................................................................................................................................

8-8

4.

Parking the Tractor..................................................................................................................

8-9

 

Applying the Parking Brake ...................................................................................................................................

8-9

 

Releasing the Parking Brake .................................................................................................................................

8-9

5.

Safe Practices for Operation .................................................................................................

8-10

 

Engaging the Differential Lock.............................................................................................................................

8-10

 

Disengaging the Differential Lock........................................................................................................................

8-10

 

Hydro Static Transmission (HST) pressure release lever....................................................................................

8-13

 

Uphill / Downhill ...................................................................................................................................................

8-16

 

Steep Downhill.....................................................................................................................................................

8-16

 

 

9. POWER TAKE OFF (PTO) .................................................................................

9-1

1.

Operating the Power Take Off (PTO)......................................................................................

9-1

 

RearPower Take Off (PTO).................................................................................................................................

9-2

 

MidPower Take Off (PTO)...................................................................................................................................

9-2

 

Engaging the Power Take Off (PTO).....................................................................................................................

9-2

 

Disengaging the Power Take Off (PTO)................................................................................................................

9-4

2.

Installing an Implement to the Power Take Off (PTO) Drivelines............................................

9-5

3.

Operating the Power Take Off (PTO) while the Tractor is Traveling

 

 

in the Reverse Direction (Reverse Override Function)............................................................

9-5

 

 

10.3-POINT HITCH ................................................................................................

10-1

1.

Adjusting the 3-Point Hitch ....................................................................................................

10-1

 

Right Lift Link.......................................................................................................................................................

10-2

 

Top Link...............................................................................................................................................................

10-2

 

Sway Link ............................................................................................................................................................

10-2

 

Hitch ....................................................................................................................................................................

10-2

 

 

11.HYDRAULIC SYSTEM......................................................................................

11-1

1.

3-Point Hitch Control System ................................................................................................

11-1

 

Operating the 3-Point Hitch Control / Cutting Height Adjustment Lever to Raise or Lower the 3-Point Hitch .....

11-1

 

Hydraulic Flow Control / Stop Knob.....................................................................................................................

11-2

2.

Controlling the Implement Control Valve (Option).................................................................

11-3

 

Implement Control Valve (Option) .......................................................................................................................

11-3

 

Implement Control Lever (Option) .......................................................................................................................

11-4

 

Implement Lock Lever (Option) ...........................................................................................................................

11-4

 

Connecting the Implement Hydraulic Hoses .......................................................................................................

11-5

3

Sc2400 Operator’s Manual

TABLE OF CONTENTS

....................................................................12.TIRES, WHEELS AND BALLAST

12-1

1.

Tires ......................................................................................................................................

12-1

 

Inflation Pressure.................................................................................................................................................

12-2

 

Wheel Bolt Tightening Torque .............................................................................................................................

12-2

2.

Ballast....................................................................................................................................

12-3

 

Front Ballast ........................................................................................................................................................

12-3

 

Maximum Weight.................................................................................................................................................

12-4

 

Using Liquid Weight for the Tires ........................................................................................................................

12-4

................................................................................................13.MAINTENANCE

13-1

1.

Maintenance Check List ........................................................................................................

13-1

2.

Lubricants..............................................................................................................................

13-2

3.

Replacement Parts................................................................................................................

13-3

........................................................................................14.PERIODIC SERVICE

 

14-1

■ Warranty and Repair of the Engine .......................................................................................

 

14-1

1.

Opening / Closing the Hood ..................................................................................................

 

14-2

 

Opening the Hood ...............................................................................................................................................

 

14-2

 

Closing the Hood .................................................................................................................................................

 

14-2

2.

Daily Checks .........................................................................................................................

 

14-3

 

Refilling the Fuel Tank.........................................................................................................................................

 

14-3

 

Checking the Engine Oil Level ............................................................................................................................

 

14-5

 

Checking the Transmission Oil Level ..................................................................................................................

 

14-6

 

Checking the Radiator Hoses and Clamps..........................................................................................................

 

14-7

 

Cleaning the Radiator Cooling Fins and Screen .................................................................................................

 

14-7

 

Cleaning the Rear Grille Screen..........................................................................................................................

 

14-8

 

Checking the Cooling System .............................................................................................................................

 

14-9

 

Checking the Fuel Line......................................................................................................................................

 

14-10

 

Checking the Intake Air Hoses and Clamps ......................................................................................................

 

14-10

 

Checking the Safety Interlock System...............................................................................................................

 

14-11

 

Checking and Adjusting the Brake ....................................................................................................................

 

14-13

 

Checking the Seat Belt and Roll-Over Protective Structure (ROPS)

.................................................................14-13

 

Checking the Wheel Bolt Tightening Torque .....................................................................................................

 

14-14

 

Checking the Inflation Pressure.........................................................................................................................

 

14-14

 

Checking the Light Bulbs...................................................................................................................................

 

14-15

 

Checking the Tie-rod Rubber Boots ..................................................................................................................

 

14-15

 

Checking the Hydraulic Hoses ..........................................................................................................................

 

14-16

3.

First 50 Hours......................................................................................................................

 

14-18

 

Changing the Engine Oil....................................................................................................................................

 

14-18

 

Replacing the Engine Oil Filter ..........................................................................................................................

 

14-18

 

Changing the Transmission Oil .........................................................................................................................

 

14-18

 

Replacing the Transmission Oil Filter................................................................................................................

 

14-18

4.

Every 50 Hours....................................................................................................................

 

14-18

 

Checking the Front Axle Oil Level .....................................................................................................................

 

14-18

 

Checking the Fuel / Water Separator ................................................................................................................

 

14-19

 

Adjusting the Fan Belt .......................................................................................................................................

 

14-20

 

Greasing and Lubricating ..................................................................................................................................

 

14-21

5.

Every 100 Hours..................................................................................................................

 

14-23

 

Engine Oil ..........................................................................................................................................................

 

14-23

 

Changing the Engine Oil....................................................................................................................................

 

14-23

 

Cleaning the Fuel / Water Separator .................................................................................................................

 

14-24

 

Cleaning the Air Cleaner Element .....................................................................................................................

 

14-25

Sc2400 Operator’s Manual

4

 

 

 

TABLE OF CONTENTS

6.

Every 200 Hours..................................................................................................................

14-27

 

Replacing the Engine Oil Filter ..........................................................................................................................

14-27

 

Adjusting the Toe-in...........................................................................................................................................

14-28

7.

Every 300 Hours..................................................................................................................

14-28

 

Transmission Oil................................................................................................................................................

14-28

 

Changing the Transmission Oil and Replacing the Transmission Oil Filter.......................................................

14-29

8.

Every 500 Hours..................................................................................................................

14-30

 

Front Axle Case Oil ...........................................................................................................................................

14-30

 

Changing the Front Axle Case Oil .....................................................................................................................

14-30

 

Replacing the Fuel Filter Element (in the Fuel / Water Separator)....................................................................

14-31

 

Replacing the Fuel Filter....................................................................................................................................

14-31

9.

Every 1000 Hours................................................................................................................

14-32

 

Coolant ..............................................................................................................................................................

14-32

 

Flushing the Cooling System.............................................................................................................................

14-33

 

Changing the Coolant........................................................................................................................................

14-35

 

Adjusting the Engine Valve Clearance ..............................................................................................................

14-35

 

Checking the Fuel Injection Nozzle Injection Pressure .....................................................................................

14-35

 

Checking the Fuel Injection Pump.....................................................................................................................

14-35

10.Every 1 Year........................................................................................................................

14-36

 

Replacing the Air Cleaner Element ...................................................................................................................

14-36

 

Flushing the Cooling System.............................................................................................................................

14-36

 

Changing the Coolant........................................................................................................................................

14-36

11.Every 2 Years......................................................................................................................

14-36

 

Replacing the Radiator Hoses and Clamp ........................................................................................................

14-36

 

Replacing the Fuel Line.....................................................................................................................................

14-36

 

Replacing the Intake Air Hose ...........................................................................................................................

14-36

 

Replacing the Hydraulic Hoses .........................................................................................................................

14-36

 

 

15.SERVICING THE ELECTRICAL SYSTEM .......................................................

15-1

1.

Battery ...................................................................................................................................

15-1

 

Special Note for the Battery.................................................................................................................................

15-1

 

Servicing the Battery Safely ................................................................................................................................

15-2

 

Inspecting the Battery..........................................................................................................................................

15-3

 

Removing and Installing the Battery....................................................................................................................

15-3

 

Cleaning the Battery and Terminals ....................................................................................................................

15-4

 

Using a Booster Battery.......................................................................................................................................

15-5

2.

Fuses.....................................................................................................................................

15-6

 

Replacing the Accessory Fuses ..........................................................................................................................

15-6

 

Checking the Alternator Fuse and the Main Fuse ...............................................................................................

15-6

3.

Bulb .......................................................................................................................................

15-7

 

Replacing the Headlight Bulb ..............................................................................................................................

15-7

 

Replacing the Work Light Bulb ............................................................................................................................

15-8

 

Replacing the Tail Light Bulb...............................................................................................................................

15-9

 

Replacing the Turn Signal / Hazard Lights Bulb..................................................................................................

15-9

 

Replacing the Instrument Panel Light Bulb .......................................................................................................

15-10

4.

Headlights ...........................................................................................................................

15-10

 

Adjusting the Headlights....................................................................................................................................

15-10

5

Sc2400 Operator’s Manual

TABLE OF CONTENTS

.........................................................................................................16.STORAGE

16-1

1.

Safe Practices for Storage ....................................................................................................

16-1

 

Fuel......................................................................................................................................................................

16-2

 

Engine .................................................................................................................................................................

16-2

2.

Preparing the Stored Tractor for Operation...........................................................................

16-3

......................................................................................17.TROUBLESHOOTING

17-1

1. How to Use the Troubleshooting Table .................................................................................

17-1

 

 

18.INDEX................................................................................................................

18-1

Sc2400 Operator’s Manual

6

1.SAFETY PRECAUTIONS

1.SAFETY PRECAUTIONS

1. About This Manual

This Operator’s Manual presents you messages that

 

 

 

 

 

 

help you remain aware of potential hazards and

 

 

 

possible machine damage in operating and servicing

 

 

 

your machine. Carefully study all the information in it

 

 

 

 

REAR

 

so that you can positively avoid personal injury and

RIGHT

 

 

 

 

damaged properties.

 

 

 

NOTE:

●Unless otherwise stated, the expressions–right- hand side, left-hand side, front side, and rear side, used throughout this manual refer to the sides relative to the direction of forward movement with

the tractor.

 

 

 

 

 

 

 

LEFT

 

 

FRONT

 

 

 

 

 

P3014903

1-1

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

2. Safety-Alert Symbols

The safety-alert symbols appear with most safety statements. It means attention, become alert, your safety is involved!

Please read and strictly observe the message that follows the safety-alert symbols.

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates a situation which can cause damage to the machine, personal property and/or the environment or cause the equipment to operate improperly.

IMPORTANT: Means that implement or property damage could occur if instructions are ignored.

NOTE: Provides useful information.

WARNING: READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TRACTOR. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

WARNING: The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

DANGER: Your tractor was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. To help prevent accidents, read and take the following precautions before operating this tractor. Failure to observe the following safety instructions could result in serious injury or death.

Sc2400 Operator’s Manual

1-2

1. SAFETY PRECAUTIONS

3. Precautions before Operating Your Tractor

1.Understand the performance and limitations of your tractor. Carefully study this Operator’s Manual and learn the instructions in it before operating or servicing your tractor. Keep the Operator’s Manual in an easily accessible place.

2.Strictly follow the statements given in the DANGER, CAUTION and WARNING safety decals attached to the tractor.

3.For operator safety, always install the Roll-Over Protective Structure (ROPS).

Keep the seat belt fastened while operating the tractor with the Roll-Over Protective Structure (ROPS). This practice will reduce the possibility of injury or death in the event of roll-over accident.

If the Roll-Over Protective Structure (ROPS) has been removed for any reason, be sure to reinstall all the associated parts before operating the tractor.

Do not alter the Roll-Over Protective Structure (ROPS). The altered Roll-Over Protective Structure (ROPS) may fail to provide the designed protection.

Replace the damaged Roll-Over Protective Structure (ROPS) immediately. Contact your local Cub Cadet Yanmar dealer for technical assistance.

NEVER alter or repair the Roll-Over Protective Structure (ROPS). Welding, bending, drilling, grinding, or cutting may weaken the Roll-Over Protective Structure (ROPS). Contact your local Cub Cadet Yanmar dealer for technical assistance.

4.Always fasten the seat belt while operating the tractor with the Roll-Over Protective Structure (ROPS).

Check the seat belt for any damage. Replace the damaged seat belt immediately. Contact your local Cub Cadet Yanmar dealer for technical assistance.

Do not use the seat belt if the tractor does not have the Roll-Over Protective Structure (ROPS).

5.Check overhead clearance carefully before driving under power lines, wires, bridges or low hanging tree branches, before entering or leaving building, or in any other situation where the operator and/or Roll-Over Protective Structure (ROPS) may be struck, which could result in serious injury.

6.Make sure that any person (other than a usual operator) who will operate the tractor studies this Operator’s Manual before operation. Know the controls and how to stop the machine quickly.

7.Make sure that any person or obstacle is not under or around the tractor before and during operation. Be sure to maintain sufficient overhead clearance above the tractor.

8.Do not operate your tractor and/or implement installed to it while you are under the influence of alcohol, drug, medicine or controlled substance(s) or when you are not fit for operation of your tractor.

9.For operation, wear close-fitting clothing. When operating the tractor or working around the tractor, do not wear loose-fitting clothes or jewelry, or baggy or damaged clothing. When caught by a moving part of the tractor, an accident can result. Cut-off pants or shorts do not provide protection against flying debris. Never operate the tractor in bare feet, sandals, or sneakers. Wear additional protections including non-slip safety boots or shoes, and safety goggles and gloves, etc. as appropriate or required by currently applicable local laws and regulations. Wear ear protection in a noisy environment to prevent hearing damage and reduce operator fatigue.

10.NEVER allow a passenger on any portion of the tractor.

11.Remain seated in the operator’s station when operating the tractor.

12.Make sure that the brakes, clutch and other mechanical components are free from misadjustment and excessive wear. Replace any excessively worn or damaged component immediately. At regular intervals, check that all the nuts, bolts and screws are appropriately tightened. (For details, see “MAINTENANCE”)

1-3

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

13.Always keep your tractor clean. Dust, grease or grass clippings accumulated on your tractor can lead to fire accidents or personal injury.

14.Use the handholds and running board steps when getting on and off the tractor to help prevent accidental falls. Keep the running boards clear of mud and debris.

15.Only use the implements that satisfy the requirements in this manual or are approved by your Cub Cadet Yanmar dealer. (See “4. IMPLEMENT CAPACITIES”)

16.When using front or rear mounted implements, install an appropriate weight(s) to the front or rear of your tractor to prevent upsetting of the tractor. If you choose to use the front loader, mount an implement or ballast to the 3-point hitch in order to get the tractor to stabilize. Observe the instructions about safety in the manual for the implement to be used.

17.Do not attempt to modify your tractor. Modification can deteriorate the performance and/or safety of your tractor, possibly leading to personal injury or property damage.

4. Safe Practices for Operating Your Tractor

1. Starting Your Tractor

1.Remain seated in the operator’s station when starting the engine, or actuating the levers or controls. Do not start the engine or operate controls while standing beside the tractor.

2.Before starting the engine, make sure that the forward and reverse drive pedal are in the neutral positions, the parking brake is engaged, and the Power Take Off (PTO) is disengaged.

3.Always keep the seat belt fastened around your waist whenever the tractor has the Roll-Over Protective Structure (ROPS).

4.Start the engine of your tractor only by using the starter key switch. Do not attempt to start the engine by short-circuiting across the starter solenoid terminals with a jumper wire, or by bypassing the safety start switch. This defeats the safety interlock circuit and the tractor may begin to move and/or the Power Take Off (PTO) shafts may begin to rotate, possibly leading to personal injury or property damage.

5.Do not run or idle the engine in a confined area that is poorly ventilated or not ventilated at all. The engine emits carbon monoxide gas that is colorless, odorless and can cause death.

6.Before operation, check that all the safety features are functioning correctly. Never tamper with safety devices. Check their proper operation regularly. Contact your Cub Cadet Yanmar dealer if safety devices malfunction.

7.Avoid accidental contact with control pedals while the engine is running, as this can cause unexpected movement of the tractor.

8.Never leave a running machine unattended.

Sc2400 Operator’s Manual

1-4

1. SAFETY PRECAUTIONS

2. Working with Your Tractor

1.Make sure that all the covers and guards are in correct position. Replace any missing or damaged cover immediately.

2.Before turning or when traveling on a rough terrain, or before stopping, decrease the tractor speed in order to prevent upsetting.

3.Use extra caution when operating over rough ground, when crossing ditches or slopes, and when turning corners.

4.Do not attempt to turn with the differential lock engaged. Attempting to turn the tractor while the differential lock is engaged can lead to a roll-over.

5.Stay clear of ditches, holes, embankments or ponds. A hazard of tractor upset can occur more easily if the ground is soft or wet. Before entering an area covered with tall grass, walk the area to detect any obstacles.

6.Always watch where you are going, especially at blind corners, trees, or other objects that can obscure your vision. Remain alert when you are approaching the end of a row, trees or any obstacle.

7.When two or more people are working in one area, always keep in good communication with each other.

8.Do not get on or off a moving tractor.

9.Make certain all tractor lights are illuminated when operating at night.

3. Considerations for Safety of Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine. They do not understand the dangers. Never assume they will remain where you last saw them.

1.Keep children out of the operating area and in the watchful care of an adult other than the operator.

2.Be alert if a child enters the work area, stop your tractor immediately.

3.Never allow a child to ride on the tractor. They may fall off and be seriously injured or interfere with safe machine operation.

4.Never allow children under 16 years old to operate the machine. Children 16 years and over should only operate machine under close parental supervision and proper instruction.

5.Be extremely careful when backing the tractor. Before and during backing, look back and downward. A child may be in your path.

6.Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure your vision of a child or other hazard.

7.Never allow a child to play on the tractor or implement.

8.Keep children away from hot or running engines. They may suffer burns.

9.Park your tractor on a solid, flat and level place. Engage the parking brake securely, remove the key from the starter key switch to prevent unauthorized operation. If parking on a slope is unavoidable, park the tractor across the slope and chock the wheels.

1-5

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

5. Operating Your Tractor on Slopes

On a slope, the tractor is less stable and more prone to tip-over, possibly leading to serious injury or death. Remain very cautious when your tractor is on any slope.

A2019005

DO:

●Operate up and down slopes, not across. ●Remove obstacles such as rocks, limbs, etc. ●Watch for holes, ruts or bumps. Uneven terrain

could overturn the machine. Tall grass can hide such obstacles.

●Place the transmission in the slow range when

climbing or descending slopes.

●Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Rapid engagement or braking could cause the front of the machine to lift and rapidly flip over backwards which could cause serious injury.

●Avoid starting or stopping on a slope. If tires lose traction, disengage the Power Take Off (PTO) and proceed slowly straight down the slope.

●To avoid upset, move backward up a steep slope. If backing on the slope is not comfortable, do not attempt to continue. Avoid an extremely steep slope.

●When moving forward to escape from a ditch, or deep mud, or when traveling on a steep slope, the risk of the tractor upsetting backward is high. Always move backward to escape these situations. In the four-wheel drive mode, special caution is needed to avoid false confidence in the tractor’s ability to climb slopes.

DO NOT:

Do not mow near drop-offs, ditches or embankments. The mower could suddenly turn over if a wheel goes over the edge of a cliff or ditch, or if an edge caves in.

WARNING

Before approaching a slope, select an appropriate speed setting. Be sure to run the tractor at a lower speed on slopes.

Suddenly starting the tractor on an uphill can cause the front wheels to jump off the ground,

and this situation poses an extreme danger. To avoid this problem, run the engine at a lower speed, and gently start the tractor.

Do not park the tractor on a slope. If parking on a slope is unavoidable, chock the tires, and engage the parking brake securely.

Sc2400 Operator’s Manual

1-6

1. SAFETY PRECAUTIONS

6. Traveling on a Road

1.Disengagement of the 4-wheel drive is recommended.

2.Remember that the braking characteristics differ between the two and four wheel drive modes. Be aware of the current drive mode and use carefully.

3.Before turning, always slow down the tractor. High-speed turn may cause the tractor to tip over.

4.When traveling on a road, be sure that the Slow Moving Vehicle (SMV) emblem is on the tractor and is clearly visible. Use the hazard lights and turn lights as required by the currently effective local laws or regulations.

5.Strictly observe all the currently effective local traffic and safety laws and regulations.

6.Turn ON the headlights as required by the currently effective local laws or regulations.

7.Always travel at a speed that allows you to maintain control of the tractor.

8.Avoid engaging differential lock while traveling on a road. It may cause the operator to lose control of the tractor.

9.While traveling on a road, do not suddenly turn the steering wheel. Such an action can lead to loss in the stability of the tractor, and can cause an extremely dangerous situation.

10.While on a road, do not attempt to operate an implement. During transportation, put the 3-point hitch control / cutting height adjustment lever in its raised position and lock it with the position stop knob. Do not fully close the hydraulic flow control / stop knob.

7. Safe Practices for Parking Your Tractor

1.Disengage the Power Take Off (PTO), lower the implement to the ground, set the forward and reverse drive pedal in the neutral positions, engage the parking brake securely, stop the engine and remove the key from the starter key switch.

2.Before leaving your tractor, be sure the tractor is completely stopped.

3.Do not park on a steep slope. Rather, park on solid, flat, level ground whenever possible. If parking on a slope is unavoidable, park the tractor across the slope, and lower the implement to the ground and chock the wheels.

4.Allow the tractor to cool at least 5 minutes before storing.

1-7

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

8. Operating the Power Take Off (PTO)

1.Before getting off the tractor, connecting/ disconnecting an implement, adjusting, cleaning or servicing a Power Take Off (PTO)-driven implement, make sure that all the moving components are at a standstill.

2.Ensure that the Power Take Off (PTO) shaft cover is always in place. Replace the Power Take Off (PTO) shaft cap only when the shaft is at a standstill.

3.Before installing or operating Power Take Off (PTO)-driven implement, carefully study the manufacturer’s Operator’s Manual and the safety decals on the implement.

4.When installing the Power Take Off (PTO)- driven implements, engage the parking brake securely and chock the four wheels. Do not approach or access any rotating component.

9. Using the 3-Point Hitch

1.Use the 3-point hitch only in conjunction with the implement that is specifically designed for use with the 3-point hitch.

2.Before using a 3-point hitch mounted implement, the appropriate counterbalance may need to be installed on the front of the tractor.

10. Safety Frame (Roll-Over Protective Structure) (ROPS) Precautions

Your tractor is equipped with a Roll-Over Protective Structure (ROPS) which must be maintained in a fully functional condition. Check overhead clearance carefully before driving under power lines, wires, bridges or low hanging branches, before entering or leaving buildings, or in any other situation where the operator and/or Roll-Over Protective Structure (ROPS) may be stuck, which could result in serious injury.

1.Never modify the Roll-Over Protective Structure (ROPS) in any way.

2.Never attempt to straighten or reweld any part of the main frame or retaining brackets that have been damaged. Doing so may weaken the structure and endanger your safety.

3.Never secure any parts on the main frame or attach the safety frame with anything other than the special fasteners specified.

4.Never attach ropes, chains, or cables to the RollOver Protective Structure (ROPS) for pulling purposes.

5.Although the Roll-Over Protective Structure (ROPS) provides the operator the maximum protection possible, never take unnecessary risks.

Sc2400 Operator’s Manual

1-8

1. SAFETY PRECAUTIONS

11. Safe Practices for Servicing Your Tractor

Before starting any servicing work, park your tractor on solid, level ground, engage the parking brake securely, disengage the Power Take Off (PTO), lower the implement to the ground, set the forward and reverse drive pedal to the neutral position, stop the engine and remove the key from the starter key switch.

1.Always keep a first-aid kit and a fire extinguisher readily available.

2.Before accessing the engine, muffler, radiator or other possibly hot components, wait until the tractor has fully cooled off.

3.Use extreme care in handling diesel fuels. They are extremely flammable and the vapors are explosive. Use only an approved container.

4.Be sure to stop the engine before refueling. After refueling, replace fuel cap securely and wipe off any spilled fuel before starting the engine as it may cause a fire or explosion.

5.Do not smoke while refueling. Keep any spark or open flame away from the fuel tank.

6.Never refuel the machine indoors because fuel vapors will accumulate in the area.

7.Never store the fuel container or machine inside where there is an open flame or spark, such as a gas hot water heater, space heater or furnace.

8.Do not smoke while working around the battery. Keep any spark or open flame away from the battery. The battery emits hydrogen and oxygen gas, in particular, during recharging and can pose a hazard of explosion.

9.Prior to “jump starting” a tractor that has a fully depleted battery, read and follow all the instructions in the “7. OPERATING THE ENGINE”.

10.Carefully loosen the radiator cap to the first stop, and allow excessive pressure to escape, and only then remove the radiator cap. If the tractor is equipped with a coolant reserve tank, add coolant or water to the reserve tank, not to the radiator (See “Checking the Cooling System”).

11.Before working on or around electric components, first disconnect the battery ground cable.

12.To prevent a spark occurring from short-circuit, disconnect the battery grounding (–) terminal first and reconnect last.

13.The operator must not mount a tire onto a rim. Only qualified personnel should do this task.

14.Always keep the tires at a correct pressure level. Do not exceed the recommended tire pressure specified in the Operator’s Manual.

15.Keep the tractor securely supported while changing the wheels or adjusting the wheel tread width. Be sure to tighten the wheel bolts at the specified tightening torque.

1-9

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

16.Avoid working under any hydraulically supported devices. Such devices can settle, suddenly leak down, or be accidentally lowered. If working beneath the tractor, or an implement, is unavoidable, be sure to support the tractor or implement with appropriate stands or lift apparatus.

17.High pressure hydraulic fluid, when released, can penetrate human skin, possibly leading to serious personal injury. Before disconnecting any hydraulic line, fully release the internal pressure. Before exerting a pressure to the hydraulic system, make sure that all connections are tight and all the lines, pipes and hoses are free from fissure/crack or any other damage.

18.Check brake operation frequently. Adjust and service as required.

19.Do not change the engine governor settings or overspeed the engine. Excessive engine speeds are dangerous.

20.Observe proper disposal laws and regulations. Prior to disposal, determine the proper method to dispose of waste from your local Environmental Protection Agency. Recycling centers are established to properly dispose of materials in an environmentally safe fashion.

21.Use proper containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them. Properly dispose of the containers immediately following the draining of fluids.

22.DO NOT pour oil or other fluids into the ground, down a drain or into a stream, pond, lake or other body of water. Observe Environmental Protection Agency regulations when disposing of oil, fuel, coolant, brake fluid, filters, batteries, tires and other harmful waste.

23.We do not recommend the use of a pressure washer or garden hose to clean your unit. They may cause damage to electrical components; spindles; pulleys; bearings; or the engine. The use of water will result in shortened life and reduce serviceability.

WARNING: YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

Sc2400 Operator’s Manual

1-10

1. SAFETY PRECAUTIONS

12.Understanding the Tractor Safety Decals

Safety-Alert Symbols

The tractor safety decals illustrated in this section are provided in critical areas on the tractor so that people including the operator can remain always aware of potential hazards.

The tractor safety decals contain the words DANGER, WARNING and CAUTION together with the safety-alert symbols. DANGER and WARNING stand for the most serious hazards.

The Operator’s Manual also contains special safety messages that explain potential hazards about which the operator must remain cautious. These messages are presented together with the word CAUTION and the safety-alert symbols.

Care of DANGER, WARNING and CAUTION Decals

1.Always keep all the danger, warning and caution decals clean and clearly legible.

2.Clean the danger, warning and caution decals with soap water, and wipe dry with clean soft cloth.

3.Replace damaged or missing danger, warning and caution decals with new decals available from your local Cub Cadet Yanmar dealer.

4.If a component having a danger, warning or caution decals is replaced with a new one, make sure that a new decal is on the same location as on the old component.

5.Affix a new danger, warning or caution decals flat on a clean, dry surface, squeezing out trapped air.

1-11

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

(A) CY1A8160-65300

DANGER
TO AVOID INJURY OR DEATH:

●Do not start engine by shorting across starter terminals or bypassing safety start switch.

●Start engine only from seat with transmission and PTO OFF.

(A)

P3014902

(B) CY1A7880-65620

WARNING

STAY CLEAR OF ENGINE FAN AND FAN BELT

DANGER TO AVOID INJURY OR DEATH:

Do not start engine byshorting across starterterminals or bypassingsafety start switch.

Start engine only fromseat with transmissionand PTO OFF.

1A8160-65300

(B)

P3014961

WARNING

STAY CLEAR OF

ENGINE FAN

AND FAN BELT

Sc2400 Operator’s Manual

1-12

1. SAFETY PRECAUTIONS

(C) CY124764-44810

CAUTION

1.Adding of water is done through the sub-tank.

2.Before starting, make sure that water level is up to the "Full" mark.

3.If water level is low, remove the cap of the subtank and add water until the "Full" mark is reached.

(C)

P3014947

(D) CY1A8160-51520

DANGER/POISON (ENGLISH)

●SHIELD EYES: EXPLOSIVE GASES CAN CAUSE BLINDNESS OR INJURY.

●NO SPARKS, FLAMES, SMOKING. ●SULFURIC ACID CAN CAUSE BLINDNESS OR

SEVERE BURNS.

●FLUSH EYES IMMEDIATELY WITH WATER. SEEK MEDICAL HELP RIGHT AWAY.

●KEEP OUT OF REACH OF CHILDREN. DO NOT TIP.

●KEEP VENT CAPS TIGHT AND LEVEL.

(D)

P3014933

P3013722a

1-13

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

(E) CY1A7880-65600

(E)

WARNING

READ OPERATOR'S MANUAL

1.Do not operate the machine without guards shields and safety devices in place and working.

2.Keep all riders off tractor during operation.

3.Make certain everyone is clear of machine before starting engine or operation.

4.Keep hands, feet and clothing away from powerdriven parts.

5.Use seat belt.

6. Reduce speed when turning or operating around

P3014940

hazards, on rough ground or steep slopes.

 

7.Do not allow operation of the machine by untrained personnel.

8.Stop engine, lower implement to ground and lock park brake before dismounting.

9.Wait for all movement to stop before servicing machinery.

10.Remove key if leaving tractor unattended.

11.Securely support tractor and implements before working underneath.

12.On public roads use SMV emblem and hazard lights.

13.Do not jump if machine tips.

 

 

 

WARNING

3.Make certain everyone is clear of machine

8.Stop engine, lower implement to ground

RE

 

before starting engine or operation.

 

ounting.

AD OPERA

 

 

and lock park brake before dism

 

 

TOR'S

4.Keep hands, feet and clothing away from

9.Wait for all movement to stop before

MA

NUAL

power-driven parts.

servicing machinery.

 

1.Do

 

 

 

5.Use seat belt.

10.Remove key if leaving tractor unattended.

 

not o

 

 

6.Reduce speed when turning or operating

 

nts

shields aperate the machine withou

11.Securely support tractor and impleme

working.

nd safety devices in place t guards

around hazards, on rough ground or steep

before working underneath.

2.Keep all

rider

 

and

slopes.

12.On public roads use SMV

emblem and

 

 

7.Do not allow operation of the machine by

 

 

 

 

s off tractor during o

peration.

hazard lights.

 

 

 

 

 

 

untrained personnel.

13.Do not jump if machine tips.

(F) CY1A7880-65630

IMPORTANT
12V DC OUTLET

1.DO NOT CONNECT A LIGHT OR LOAD OF MORE THAN 120 WATTS.

2.DO NOT USE AS A CIGARETTE LIGHTER.

3.REMOVE PLUG FROM SOCKET WHEN NOT IN USE.

4.DO NOT USE WHEN WET.

P3014958

1A7880-65600

(F)

IMPORTANT

12V DC OUTLET

1.DO NOT CONNECT A LIGHT OR LOAD OF MORE THAN 120 WATTS.

2.DO NOT USE AS A CIGARETTE LIGHTER. 3.REMOVE PLUG FROM SOCKET WHEN NOT IN USE.

4.DO NOT USE WHEN WET.

1A7880-65630

Sc2400 Operator’s Manual

1-14

1. SAFETY PRECAUTIONS

(G) CY1A7880-65350

WARNING

Only use PTO in reverse when there are no children or others around

(G)

P3014940

(H) CY1A7880-85170

WARNING

This structure's protective capability may be impaired by structural damage, overturn, or alteration.

If any of these conditions occur, this structure must be replaced.

(I) CY1A7880-85180

WARNING

Use seat belt

WARNING

Only use PTO in reverse when there are no children or others around

(H)

( I )

P3014939

(H)

( I )

1-15

Sc2400 Operator’s Manual

1. SAFETY PRECAUTIONS

(J) CY198220-65621

WARNING
AVOID INJURY FROM PTO

●Keep all shields in place

●Keep hands, feet and clothing away ●Operate only with 540 RPM

(J)

P3014938

WARNING

AVOID INJURY FROM PTO Keep all shields in place

Keep hands,feet and clothing away Operate only with 540 RPM

(K) CY1A8160-65310

WARNING

TO AVOID INJURY:

Before leaving or servicing machine,

●Stop engine. ●Set parking brake.

●Park on level ground.

●Lower all implements to the ground. ●Remove key.

(K)

P3014959

Sc2400 Operator’s Manual

1-16

2.SERVICING THE TRACTOR

2.SERVICING THE TRACTOR

Your Cub Cadet Yanmar dealer wants to remain

 

 

 

 

committed to the tractors our customers have

 

 

 

 

purchased and intends to support our customers in

 

 

 

 

fully developing the performance of their Cub Cadet

 

 

 

 

Yanmar tractors. After carefully studying this manual,

 

 

 

 

the customers themselves will be able to do a certain

 

 

 

 

portion of the regular maintenance work.

 

 

 

 

When parts / components or major service work is

 

 

 

 

needed, contact your local Cub Cadet Yanmar dealer

 

 

 

 

for technical assistance.

 

 

 

 

 

For information about the service work, contact your

 

 

 

 

local Cub Cadet Yanmar dealer. When ordering a

 

(A)

 

part / component, inform your local Cub Cadet

P3014902

 

 

 

 

 

 

 

Yanmar dealer of the tractor and engine serial

 

 

 

 

numbers. Find both serial numbers and enter them in

 

 

 

 

the following table.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(B)

 

Type

Serial No.

 

 

 

 

Tractor

 

 

 

 

 

 

Engine

 

 

 

 

 

 

Date of Purchase

 

 

 

 

 

 

Name of Dealer

 

 

 

 

 

 

(A) Tractor identification plate with tractor serial

 

 

 

 

number

 

 

 

 

 

(B) Engine serial number

 

 

 

 

 

 

 

 

P3014901

2-1

Sc2400 Operator’s Manual

3.SPECIFICATIONS

3.SPECIFICATIONS

1. Specifications Table

 

 

Model

 

Sc2400

Power Take Off (PTO) Power

 

 

hp (kW)

16.5 (12.3)

 

Maker

 

 

 

YANMAR

 

Model

 

 

 

3TNV72

 

Type

 

 

 

Indirect Injection, Vertical,

 

 

 

 

Water-Cooled, 4 Cycle Diesel

 

 

 

 

 

 

Number of Cylinders

 

3

 

Bore and Stroke

 

 

in. (mm)

2.834 × 2.913 (72 × 74)

 

Total Displacement

 

 

cu. in. (L)

55.1 (0.903)

Engine

Gross Power

 

 

hp (kW)

24.0 (17.9)

 

Net Power

 

 

hp (kW)

20.4 (15.0)

 

Rated Revolution

 

 

rpm

3300

 

High Idle Speed

 

 

rpm

3470

 

Low Idle Speed

 

 

rpm

1150

 

Maximum Torque

 

 

ft•lb (N•m)

38.3 (52.3)

 

Battery

 

 

 

12V BP24 , CCA: 540 A

 

Fuel

 

 

 

Diesel Fuel No.1-D , No.2-D

 

Fuel Tank

 

 

US gal (L)

Approximately 5.8 (22)

Capacities

Engine Oil

 

 

US qt (L)

Approximately 2.5 (2.4)

Engine Coolant

 

 

US qt (L)

Approximately 3.4 (3.2)

 

 

 

 

Transmission Oil

 

 

US gal (L)

Approximately 2.0 (7.5)

 

Overall Length (without 3-Point Hitch)

in. (mm)

82.7 (2100)

 

Overall Length (with 3P)

in. (mm)

95.5 (2425)

 

Overall Width (with R4 Tires)

in. (mm)

44.5 (1130)

 

Overall Height (with Roll-Over Protective Structure

in. (mm)

71.5 (1817)

 

(ROPS), R4 Tires)

 

 

 

 

 

 

 

Dimensions

Overall Height (with R4 Tires)

in. (mm)

49.9 (1267)

 

(Top of Steering Wheel)

 

 

 

 

Wheel Base

 

 

in. (mm)

55.1 (1400)

 

Min. Ground Clearance (with R4 Tires)

in. (mm)

7.5 (190)

 

Tread (with R4)

 

Front

in. (mm)

34.6 (879)

 

 

Rear

in. (mm)

32.2 (820)

 

 

 

Weight (with Roll-Over Protective Structure (ROPS) and R4 Tires)

lb (kg)

1279 (580)

Sc2400 Operator’s Manual

3-1

3. SPECIFICATIONS

 

 

Ag (R1)

Front

 

18 × 8.50-10

 

 

Rear

 

26 × 12.00-12

 

 

 

 

 

Tire

Turf (R3)

Front

 

18 × 8.50-10

 

Rear

 

26 × 12.00-12

 

 

 

 

 

 

Industrial (R4)

Front

 

18 × 8.50-10

 

 

Rear

 

26 × 12.00-12

Traveling

Clutch

 

 

 

System

 

 

 

 

 

Steering

 

 

 

Power Steering

 

 

 

 

 

Transmission

 

 

 

Hydrostatic Transmission,

 

 

 

 

2 Range Speeds

 

 

 

 

 

 

Drive

 

 

 

Selected 4WD

 

Brake

 

 

 

Wet plates

 

Minimum Turning Radius

 

ft (m)

7.2 (2.2)

 

Differential Lock

 

 

 

Foot Pedal Control

 

Hydraulic Control System Type

 

 

Position Control

 

Pump Capacity (main)

 

 

US gal/min

Approximately 3.4 (13.2)

 

 

 

(L/min)

 

 

 

 

 

 

Pump Capacity (steering)

 

US gal/min

Approximately 3.4 (13.2)

Hydraulic Unit

 

(L/min)

 

 

 

 

3-Point Hitch

 

 

 

Limited Category I

 

 

 

 

 

Max. Lift Force

Lift Point

 

lb. (kg)

1036 (470)

 

24 in. Behind Lift Point

lb. (kg)

661 (300)

 

 

 

System Pressure

 

 

psi (MPa)

1813 (12.5)

 

Type

 

 

 

Electric Clutch

 

 

Shaft Size

 

 

SAE 1-3/8, 6-Splines

Power Take Off

Rear

Type

 

 

Independent

 

Speed / Engine

 

rpm

540 / 3111

(PTO)

 

 

 

Shaft Size

 

 

SAE 16/32, 15-Splines

 

 

 

 

 

Mid

Type

 

 

Independent

 

 

Speed / Engine

 

rpm

2100 / 3338

2. Traveling Speeds

 

Model

 

Sc2400

 

 

Range Shift Lever

mph

 

km/h

Forward

 

Slow

0-6.0

 

0-9.7

 

Fast

0-9.3

 

0-15

 

 

 

Reverse

 

Slow

0-3.6

 

0-5.8

 

Fast

0-5.6

 

0-9

 

 

 

3-2

Sc2400 Operator’s Manual

4.IMPLEMENT CAPACITIES

4.IMPLEMENT CAPACITIES

The Cub Cadet Yanmar tractor has been carefully tested in the configuration equipped with implements sold or approved by Cub Cadet Yanmar and has proved to perform properly. Do not use any implement that has not been sold or recommended by a Cub Cadet Yanmar dealer, or that fails to satisfy the specified values given below. Never mount an implement that is not approved for the Cub Cadet Yanmar tractor. Using unapproved implements could result in malfunction, failure, and damage to the tractor and/or implement, and increase the possibility of injury to the operator or other people. The Cub Cadet Yanmar warranty does not cover any malfunction or failure that results from use of an unapproved implement.

 

 

24in. Behind Lift Point

 

 

 

Maximum Vertical

 

 

Maximum

 

 

 

Maximum

 

Implement Weight

 

 

 

 

 

 

 

 

Hitch Load

 

Towing Capacity

 

 

Lifting Capacity

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W0

 

W1

 

W2

 

 

W3

 

lb

 

661

 

As specified in the list

 

331

 

 

 

661

 

 

kg

 

300

 

below.

 

150

 

 

 

300

 

 

A3013714a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Implement

 

Remarks

 

 

Unit

Amount

 

 

 

 

Maximum Lift Capacity (at Pivot)

 

 

lb (kg)

700

 

317

Front - End Loader

Maximum Overhang (Pivot - Front Tire Center)

 

in. (mm)

40

 

1022

Maximum Weight

 

 

 

lb (kg)

441

 

200

 

 

 

 

 

 

 

 

 

 

 

 

Maximum Oil Pressure

 

 

psi (MPa)

1885

 

13

 

 

 

Mid - Mount

Maximum Cutting Width

 

 

in. (mm)

60

 

1524

Mower

 

Maximum Weight

 

 

 

lb (kg)

254

 

115

 

 

 

 

 

 

 

Rear - Mount

Maximum Cutting Width

 

 

in. (mm)

48

 

1219

 

 

 

 

 

 

 

 

 

Maximum Weight

 

 

 

lb (kg)

351

 

159

 

 

 

 

 

 

 

 

Rotary Tiller

Maximum Tilling Width

 

 

in. (mm)

42

 

1067

Maximum Weight

 

 

 

lb (kg)

342

 

155

 

 

 

 

 

 

 

 

Box Scraper (Box Blade)

Maximum Cutting Width

 

 

in. (mm)

48

 

1219

Maximum Weight

 

 

 

lb (kg)

254

 

115

 

 

 

 

 

 

 

 

Rear Blade

Maximum Cutting Width

 

 

in. (mm)

60

 

1524

Maximum Weight

 

 

 

lb (kg)

176

 

80

 

 

 

 

 

 

 

 

NOTE:

●Backhoes cannot be attached.

Sc2400 Operator’s Manual

4-1

5.NAMES AND FUNCTIONS OF COMPONENTS

5.NAMES AND FUNCTIONS OF COMPONENTS

1. Appearance

(1)(2) (3) (4)

P3014903

(7)

 

(9) (8)

(20)

P3014904

(1)Headlights

(2)Hood

(3)Fuel inlet

(4)Seat

(5)Seat belt

(6)Fender

(7)Rear tires

(8)Front tires

(9)Work lights

(10)Front weight hitch (Option)

(11)Roll-Over Protective Structure (ROPS)

(12)Hydraulic quick couplers (Option)

(13)12V DC outlet (for additional rear work light)

(14)Rear Power Take Off (PTO) shaft

(5)

(10)

 

(6)

3014925a

 

 

(11)

(19)

(18)

(17)

(16)

P3014905

 

 

(12)

(15)

(14)

(13)

(15)Lower links

(16)Top link retainer

(17)Tail lights

(18)Top link

(19)Turn signal / Hazard lights

(20)Slow Moving Vehicle (SMV) emblem

 

(12)

 

3014906

5-1

Sc2400 Operator’s Manual

Cub Cadet SC2400 User Manual

5.NAMES AND FUNCTIONS OF COMPONENTS

2.Operator Station Controls

(21)

(1)

(2)

 

(3)

 

 

(20)

 

(4)

 

(5)

 

 

(6)

 

 

(7)

(19)

 

(8)

 

 

(18)

 

(9)

(17)

 

(10)

(16)

 

 

(11)

(15)

 

 

 

3014903

(13)

(12)

(14)

(22)

(25)

 

(24)

 

 

(23)

 

 

 

3014904

 

 

 

 

 

 

(1)

Hazard lights button switch

(14) Hydro Static Transmission (HST)

(2)

Starter key switch

 

pressure release lever

(3)

Throttle control lever

(15) Cup holder

(4)

Parking brake lever

(16) Reverse - override - switch

(5)

Brake pedal

(17) Power Take Off (PTO) switch

(6)

Forward and reverse drive pedal

(18) Range shift lever

(7)

Implement control lever (Option)

(19) Mid- / Rear-Power Take Off (PTO) select lever

(8)

Implement lock lever (Option)

(20) Turn signal switch

(9)

Position stop knob

(21) Headlight / work light switch

(10) Cruise control lever

(22) Seat adjustment lever

(11)

3-point hitch control /

(23) Differential lock foot pedal

 

cutting height adjustment lever

(24) 4-wheel drive lever

(12) Storage compartment

(25) Hydraulic flow control / stop knob

(13)

12V DC outlet

 

 

 

Sc2400 Operator’s Manual

5-2

 

 

Loading...
+ 103 hidden pages