Cub Cadet HB425 User Manual

0 (0)

Operator’s Manual

4-Cycle Gasoline Blower

HB425

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Maintenance and Repair Instructions . . . . . . . . . . . . . . . . . . . . . . .6 Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E10–E11 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

In an effort to reduce the impact on the forests, and reduce carbon and greenhouse gas emissions, MTD is using less paper by reducing the text size of this manual.

P/N 769-03822

DO NOT RETURN THIS PRODUCT

For Assistance please call 1-877-282-8684 (U.S.) or 1-800-668-1238 (Canada)

or visit www.cubcadetcommercial.com

SAVE THESE INSTRUCTIONS

For service call 1-877-282-8684 in the United States, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.cubcadetcommercial.com.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer.

Before beginning, locate the unit’s model plate. It lists the model and serial numbers of your unit. Refer to the sample plate below and copy the information for future reference.

 

MODEL :

S/N :

ITEM :

Copy the model and parent part number here:

Copy the serial number here:

All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

Copyright© 2008 MTD SOUTHWEST INC, All Rights Reserved.

(06/08)

RULES FOR SAFE OPERATION

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If it requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #753-05900 Muffler Assembly.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

SYMBOL MEANING

SAFETY ALERT: Indicates danger, warning or caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING: Failure to obey a safety warning can result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 in CANADA

• IMPORTANT SAFETY INSTRUCTIONS •

READ ALL INSTRUCTIONS BEFORE OPERATING

WARNING: When using the unit, you must follow the safety rules. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use.

Read the instructions carefully. Be familiar with the controls and proper use of the unit.

Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.

Children and teens under the age of 15 must not use the unit, except for teens guided by an adult.

All guards and safety attachments must be installed properly before operating the unit.

Inspect the unit before use. Replace damaged parts. Check for fuel leaks. Make sure all fasteners are in place and secure. Replace parts that are cracked, chipped, or damaged in any way. Do not operate the unit with loose or damaged parts.

Carefully inspect the area before starting the unit. Remove all debris and hard or sharp objects such as glass, wire, etc.

Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders, and pets outside a 50 feet (15 m.) radius; there still may be a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the unit immediately.

SAFETY WARNINGS FOR GAS UNITS

WARNING: Gasoline is highly flammable, and its vapors can explode if ignited. Take the following precautions:

Store fuel only in containers specifically designed and approved for the storage of such materials.

Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate.

Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is

hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressure in the tank.

Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Slowly remove the fuel cap only after stop-ping engine. Do not smoke while adding fuel. Wipe up any spilled fuel from the unit immediately. Always wipe unit dry before using.

Move the unit at least 30 feet (9.1 m) from the fueling source and site before starting the engine. Do not smoke or allow sparks and open flames near the area while adding fuel or operating the unit.

WHILE OPERATING

Never start or run the unit inside a closed room or building. Breathing exhaust fumes can be fatal. Operate this unit only in a well-ventilated outdoor area.

Wear safety glasses or goggles that meet ANSI Z87.1 standards and are marked as such. Wear ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty.

Wear heavy long pants, boots, gloves and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.

The cutting attachment shield must always be in place while operating the unit as a trimmer. Do not operate unit without both trimming lines extended, and the proper line installed. Do not extend the trimming line beyond the length of the shield.

This unit does not have a clutch. The cutting attachment continues rotating when the engine is idling. If it does not, have the unit adjusted by an authorized service technician.

Adjust the handle to your size in order to provide the best grip.

Be sure the cutting attachment is not in contact with anything before starting the unit.

Use the unit only in daylight or good artificial light.

Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. Refer to Starting/Stopping Instructions.

Use the right tool. Only use this tool for its intended purpose.

Do not overreach. Always keep proper footing and balance.

Always hold the unit with both hands when operating. Keep a firm grip on both handles or grips.

Keep hands, face, and feet at a distance from all moving parts. Do

2

RULES FOR SAFE OPERATION

not touch or try to stop the cutting attachment when it rotates.

Do not touch the engine, gear housing or muffler. These parts get extremely hot from operation, even after the unit is turned off.

Do not operate the engine faster than the speed needed to cut, trim or edge. Do not run the engine at high speed when not cutting.

Always stop the engine when cutting is delayed or when walking from one cutting location to another.

If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Do not operate before repairing damage. Do not operate the unit with loose or damaged parts.

Stop the unit, switch the engine to off, and disconnect the spark plug for maintenance or repair.

Use only original equipment manufacturer replacement parts and accessories for this unit. These are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to serious injury to the user, or damage to the unit, and void your warranty.

Keep unit clean of vegetation and other materials. They may become lodged between the cutting attachment and shield.

To reduce fire hazard, replace a faulty muffler and spark arrestor. Keep the engine and muffler free from grass, leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting.

Store the unit in a dry place, either locked up or up high to prevent unauthorized use or damage. Keep out of the reach of children.

Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean, and free from debris. Clean after each use, see Cleaning and Storage instructions.

Keep these instructions. Refer to them often and use them to instruct other users. If you loan this unit to others, also loan these instructions to them.

SPECIAL NOTE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands or joints, discontinue use of this tool and seek medical attention. An antivibration system does not guarantee avoidance of these problems. Users who operate power tools on a regular basis must closely monitor their physical condition and the condition of this tool.

SAVE THESE INSTRUCTIONS

Always disconnect the spark plug wire before performing maintenance or accessing movable parts.

Never store the unit, with fuel in the tank, inside a building where fumes may reach an open flame (pilot lights, etc.) or sparks (switches, electrical motors, etc.).

• SAFETY AND INTERNATIONAL SYMBOLS •

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.

READ OPERATOR'S MANUAL

WARNING: Read the operator’s manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can cause severe eye injury and hearing loss. Wear eye protection meeting ANSI Z87.1–1989 standards and ear protection when operating this unit. Use a full face shield when needed.

UNLEADED FUEL

Always use clean, fresh unleaded fuel.

OIL

Refer to operator’s manual for the proper type of oil.

SYMBOL MEANING

ON/OFF STOP CONTROL

ON / START / RUN

ON/OFF STOP CONTROL

OFF or STOP

KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially children and pets, at least 50 feet (15 m) from the operating area.

• HOT SURFACE

WARNING: Do not touch a hot muffler, gear housing or cylinder. You may get burned. These parts get extremely hot from operation. They remain hot for a short time after the unit is turned off.

• CHOKE CONTROL

1. • FULL choke position

2.• PARTIAL choke position

3.• RUN choke position

3

KNOW YOUR UNIT

 

ASSEMBLY INSTRUCTIONS

 

 

 

APPLICATIONS

 

Cleaning yards, garages, driveways,

Throttle Control

porches, patios, around walls,

 

fences and more

 

 

On/Off Stop Control

 

Cruise Control

 

Spark Plug

Blower Tube

Muffler

Cover

Handle

Air Filter Cover

Starter

Rope Grip

Oil Filler Cap

Blue Choke

Lever

 

Primer Bulb

Concentrator

Fuel Cap

Nozzle

 

ASSEMBLING UNIT

WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing the blower tubes.

WARNING: To prevent serious personal injury or damage to the unit, the blower tube must be installed while operating this unit.

Installing Blower Tube

1.Align the bump on the end of the blower tube with the bump slot on the bottom end of the blower outlet (Fig. 1).

2.Insert the bump on the blower tube into the bump slot on the blower outlet (Fig. 1).

3.Twist the blower tube clockwise inside the blower outlet until the bump locks into place (Fig. 2).

Blower

Blower

Outlet

Outlet

Blower

Blower

Tube

Tube

Bump

 

Slot

 

Bump

 

Fig. 1

Fig. 2

Installing Nozzle

1.Align the bump on the end of the blower tube with the bump slot on the end of the nozzle (Fig. 3).

2.Insert the bump on the blower tube into the bump slot on the nozzle (Fig. 3).

3.Twist the nozzle clockwise over the blower tube until tight (Fig. 4).

 

Blower

 

 

Outlet

 

 

Nozzle

Blower

Nozzle

Bump

Tube

 

 

 

 

Bump

 

 

Slot

 

 

Fig. 3

Fig. 4

Removing the Blower Tube

1.Hold the unit firmly.

2.Insert a flathead screwdriver into the tube lock and twist the screwdriver counterclockwise 1/4 turn and hold it there (Fig. 5).

3.While holding the screwdriver in a counterclockwise position, grasp the blower tube and twist it counterclockwise (Fig. 5).

4.Pull the blower tube from the blower outlet.

Removing the Nozzle

1.Hold the blower tube firmly.

2.Grasp the nozzle and twist it counterclockwise until the nozzle unlocks from the blower tube (Fig. 6).

3.Remove the nozzle from the blower tube.

 

Tube Lock

 

 

Nozzle

Blower

 

 

Tube

Blower

Blower

 

Tube

 

 

Outlet

 

 

Fig. 5

Fig. 6

4

OIL AND FUEL INFORMATION

 

STARTING/STOPPING INSTRUCTIONS

 

 

 

WARNING: OVERFILLING OIL CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY. Check and maintain the proper oil level in the crank case; it is important and cannot be overemphasized. Check the oil before each use and change it as needed. See Changing the Oil.

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is extremely important. Check the oil before each use and change the oil regularly. Failure to use the correct oil,

or using dirty oil, can cause premature engine wear and

 

failure.

 

Use a high-quality SAE 30 weight oil of API (American

 

Petroleum Institute) service class SF, SG, SH.

 

ADDING OIL TO CRANKCASE: INITIAL USE

 

NOTE: This unit is shipped without oil. In order to avoid

 

damage to the unit, put oil in the crankcase before

Funnel

you attempt to start the unit.

Spout

Your unit is supplied with one 2.03 fluid oz. (60 ml.) bottle of

 

SAE 30 SF, SG, SH oil (Fig. 7).

 

NOTE: Save the empty oil bottle. It can be used to measure

 

the correct amount during future oil changes. See

Fig. 7

Changing the Oil.

1. Unscrew the top of the bottle of oil and remove the

 

paper seal covering the opening. Replace the top. Next,

 

cut the tip off the funnel spout (Fig. 7).

Oil Fill Plug

2. Tip unit so that the back of the engine is facing up in a

 

vertical position.

 

3. Remove the oil fill plug from the crankcase (Fig. 8).

O-Ring

 

4. Pour the entire bottle of oil into the oil fill hole (Fig. 9).

NOTE: Never add oil to the fuel or fuel tank.

Oil Fill

5. Wipe up any oil that may have spilled and reinstall the oil

fill plug.

Hole

 

Check oil before each use and change as needed. Refer to

 

Checking the Oil Level.

Fig. 8

 

RECOMMENDED FUEL TYPE

WARNING: Add fuel in a clean, well ventilated outdoor area. Wipe up any spilled fuel immediately. Avoid creating a

source of ignition for spilt fuel. Do not start the engine until fuel vapors dissipate.

WARNING: Gasoline is extremely flammable. Ignited vapors may explode.

Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and

open flames at a distance from the area.

Old fuel is the primary reason for improper unit performance.

 

Be sure to use fresh, clean, unleaded gasoline.

Fig. 9

NOTE: This is a four cycle engine. In order to avoid damage

 

to the unit, do not mix oil with gasoline.

 

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can form acids when stored. Use fresh fuel (less than 60 days old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable, follow recommended precautions:

Always use fresh unleaded gasoline

Use a gas stabilizer fuel additive

Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of a gas stabilizer will inhibit corrosion and minimize the formation of gum deposits. Using a fuel additive can keep fuel from forming harmful deposits in the carburetor for up to six (6) months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions on the container. NEVER add fuel additives directly to the unit's gas tank.

FUELING THE UNIT

WARNING: Remove fuel cap slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place.

1. Remove the fuel cap (Fig. 10).

2. Place the gas container’s spout into the fill hole on the fuel tank (Fig. 10) and fill the tank. NOTE: Do not overfill the tank. 3. Wipe up any gasoline that may have spilled. 4. Reinstall the fuel cap. 5. Move the unit at least 30 ft. (9.1 m) from the fueling source and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to Federal, State and Local regulations.

Gas Can

Spout

Fuel

Cap

Fuel Tank

Fig. 10

WARNING: Operate this unit only in a well-ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area.

WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 13). To avoid serious injury, the operator and unit must be in a stable position while starting.

To avoid serious personal injury, make sure that the blower tube is locked in place or firmly installed.

STARTING INSTRUCTIONS

1.Check the oil level in the crankcase. Refer to Checking the Oil Level.

2.Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the Unit.

3. Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb and fuel lines (Fig. 11). If you can’t see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it.

4.Place the choke lever in Position 1 (Fig. 12). NOTE: The unit should be started in idle. Do not

squeeze the trigger while starting (Fig. 13).

5.Crouch in the starting position (Fig. 13) and pull the starter rope out until you feel some resistance. This is usually around 2–4 inches. Pull 4 times in smooth and rapid pulls.

6.Place the choke lever in Position 2 (Fig. 12).

7.Pull the starter rope briskly 1 to 4 times to start the engine.

8.Allow the engine to warm up for 30 to 60 seconds.

9.Place the choke lever in Position 3 (Fig. 12). The unit is ready for use.

IF... the engine does not start, go back to step 3. IF... the engine fails to start after a few attempts,

place the choke lever in Position 3 and pull the starter rope briskly 3 to 8 times. The engine should start. If not, repeat.

HOT RESTART: If the unit is already hot, place the choke lever in Position 3 and pull the starter rope to restart. The unit should be started in idle. Do not squeeze the trigger while starting (Fig. 11).

STOPPING INSTRUCTIONS

1.Release your hand from the trigger. Allow the engine to cool down by idling.

2.Press the On/Off Stop Control switch in the OFF (O) position and hold until the engine comes to a complete stop (Fig. 11).

On/Off

Choke

Lever

Primer Bulb

Position 3

Trigger

Primer

Bulb

Fig. 11

Position 2

Position 1

 

Fig. 12

Starting

Position

Starter Rope

Throttle Control

Fig. 13

5

Cub Cadet HB425 User Manual
Fig. 14

OPERATING INSTRUCTIONS

HOLDING THE BLOWER

WARNING: After starting the unit, always stand on the left side of the unit to operate it as shown in figure 15 to keep from blocking the air intake.

Before operating the unit, stand in the operating position. Check for the following:

Operator is wearing proper clothing, such as boots, safety glasses or goggles, ear/hearing protection, gloves, long pants and long sleeve shirt

If the conditions are dusty, the operator is wearing a dust mask or face mask

WARNING: To avoid serious personal injury, wear goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations.

The unit is in good working condition

• The tubes are in place and secure

Cruise

 

OPERATING TIPS

Control

SLOW

WARNING: To prevent serious

 

 

 

personal injury or damage to the unit,

 

 

make sure blower tubes are in place

 

 

before you operate the unit.

FAST

Trigger

(Idle Position)

Using the Cruise Control

1. Once the engine has started and warmed up, squeeze the trigger to accelerate the unit as needed (Fig. 14).

2. For longer periods of operation and to eliminate possible finger fatique, move the cruise control toward the FAST position to incrementally increase or maintain the unit’s engine speed (Fig. 14). When the cruise control is pressed, the trigger will recede into the handle.

3.To decrease engine speed, move the cruise control to the SLOW position and the trigger will return to idle (Fig. 14).

Other Tips

Assure the unit is not directed at anybody or any loose debris before starting the unit.

Verify that the unit is in good working condition. Make sure the tubes are in place and secure.

Always hold the unit securely when operating. Keep a firm grip on the handle.

To reduce the risk of hearing loss associated with sound level(s), hearing protection is required.

Operate power equipment only at reasonable hours— not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday.

To reduce noise levels, limit the number of pieces of equipment used at any one time.

To reduce noise levels, operate power blowers at the lowest possible speed to do the job.

Check your equipment before operation, especially the muffler, air intakes and air filters.

Use rakes and brooms to loosen debris before blowing.

In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available.

Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as screens, patios, grills, porches, and gardens.

Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away.

Clean up after using blowers and other equipment. Dispose of debris appropriately.

Use the blower for trees, shrubs, flower beds and hard- to-clean areas. Also use the unit around buildings, walls, overhangs, fences and screens, and for other normal cleaning procedures.

Hold the blower with the right hand. Do not stand on the right side of the blower when operating the unit (Fig. 15). If you do, you will be blocking the air intake and this will affect the unit’s performance. Instead, be sure to stand on the left side of the unit to maximize the unit’s efficiency (Fig. 15).

INCORRECT CORRECT POSITION POSITION

Fig. 15

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

WARNING: To prevent serious injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start.

Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any non-road engine repair establishment, individual or authorized service dealer.

NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by any non-road engine repair establishment, individual or authorized service dealer.

In order to assure peak performance of your engine, inspection of the engine exhaust port may be necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of acceleration, this service may be required. If you feel your engine is in need of this inspection, refer service to a qualified Cub Cadet service dealer for repair. DO NOT attempt to perform this process yourself as engine damage may result from contaminants involved in the cleaning process for the port.

FREQUENCY

MAINTENANCE REQUIRED

SEE

 

 

 

Before starting

Fill fuel tank with fresh fuel

p. 5

engine

Check oil

p. 6

 

 

 

Every 10 hours

Clean and re-oil air filter

p. 6

 

 

 

1st change at 10 hrs

Change oil

p. 6

2nd change at 40 hrs

Change oil

p. 6

Every 40 hours after

Clean spark arrestor and change oil

p. 7 & 6

 

 

 

10 hrs on new

Check rocker arm to valve clearance and adjust

p. 7

engine

Every 40 hours

Check rocker arm to valve clearance and adjust

p. 7

Every 40 hours

Check spark plug condition and gap

p. 7

 

 

 

200 hours

Take unit to authorized Cub Cadet service center for service

 

 

 

 

CHECKING THE OIL LEVEL

WARNING: Wear gloves to prevent injury when handling unit.

The importance of checking and maintaining the proper oil level in the crankcase cannot be overemphasized. Check oil before each use:

1. Stop the engine and allow oil to drain into the crankcase. 2. Place the engine on a level surface (Fig. 16).

3. Clean the area around the oil plug before removing it. Keep dirt, grass clippings, and other debris out of the engine.

4. Remove the oil fill plug.

5.Look into the oil fill hole (use a flashlight if needed). The oil

should be just touching the innermost thread (Fig. 17).

 

Fig. 16

 

 

 

6.If the oil level is not touching the innermost thread on the oil fill hole, add a small amount of oil to the oil fill hole and recheck (Fig. 17). Repeat this procedure until the oil level reaches the innermost thread on the oil fill hole.

NOTE: Do not overfill the unit.

NOTE: Make sure the O-ring is in place on the oil fill plug when checking and changing the oil (Fig. 18).

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of operation. Change the oil while the engine is still warm. The oil will flow freely and carry away more impurities.

1.Remove the oil fill plug.

2.Pour the oil out of the oil fill hole and into a container by tipping the unit to a vertical position (Fig. 19). Allow ample time for complete drainage.

Oil Fill Hole

Innermost Thread

Fig. 17

3.Wipe up any oil residue on the unit and clean up any oil that may have spilled. Dispose of the oil

according to Federal, State and local regulations.

Oil Fill Plug

4. Refill the crankcase with 2.03 fluid ounce (60 ml) of SAE 30 SF,

 

SG, SH oil (Fig. 20).

 

NOTE: Use the bottle and spout saved from initial use to measure

 

the correct amount of oil. The fill line on the label on the

O-Ring

bottle measures approximately 2.03 ounces (60 ml) (Fig.

 

20). Check the level, See Checking the Oil Level. If the

 

level is low, add a small amount of oil and recheck. Do not

 

overfill (Fig. 17).

 

5. Replace the oil fill plug.

Oil Fill Hole

6. Reconnect the spark plug boot.

 

 

Fig. 18

 

Fill Level

Fig. 19

Fig. 20

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Air Filter

WARNING: To avoid serious personal injury, always turn your trimmer off and allow it to cool before you clean or service it.

Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain the air filter will VOID the warranty.

1.Open the air filter cover. Push the tab on the left side of the cover inward. Then pull the air filter cover out and to the right (Fig. 21).

2.Remove the air filter (Fig. 21).

3.Wash the filter in detergent and water (Fig. 22). Rinse the filter thoroughly and allow it to dry.

4.Apply enough clean SAE 30 motor oil to lightly coat the filter (Fig. 23).

5.Squeeze the filter to spread and remove excess oil (Fig. 24).

6.Reinstall the filter (Fig. 25).

NOTE: If the unit is operated without the air filter, you will VOID the warranty.

Air Filter

Cover

Tab

Fig. 21

Fig. 22

 

 

 

Fig. 23

 

 

 

Fig. 24

 

 

 

 

 

 

 

 

 

 

 

 

 

6

MAINTENANCE AND REPAIR INSTRUCTIONS

7. Reinstall the air filter

Back

Back Plate Slots

cover. Position the

Plate Slot

 

hooks on the right

 

 

side of the air filter

 

 

cover into the slots

 

 

at the right side of

 

 

the back plate (Fig.

 

 

25).

 

 

8. Swing the cover to

 

 

the left until the tab

 

 

on the air filter cover

 

 

snaps into place in

 

 

the slot on the back

 

Fig. 25

plate (Fig. 26).

 

 

CARBURETOR ADJUSTMENT

WARNING: This unit will need to be running during idle speed adjustment. Wear protective clothing and observe all safety instructions to prevent serious personal injury.

Also, DO NOT set unit on any surface except a clean, hard area while starting or performing any adjustments. Debris, such as gravel, sand, dust, grass, etc., could be thrown by the blower tube and damage property or cause serious injury to bystanders or operator.

The idle speed of the engine is adjustable. An idle adjustment screw is between the air filter cover and the engine starter housing (Fig. 27). NOTE: Careless adjustments can seriously damage your unit. An

authorized service dealer should make carburetor adjustments.

Check Fuel

Old fuel is usually the reason for improper unit performance. Drain and refill the tank with fresh fuel prior to making any adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict air flow. This is often mistaken for an out of adjustment carburetor. Check the condition of the air filter before adjusting the idle speed screw. Refer to Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows:

1.Start the engine and let it run at a high idle for a minute to

warm up. Refer to Starting/Stopping Instructions.

2.Release the throttle trigger and let the engine idle. If the engine stops, insert a small phillips in between the Air Filter Cover and the Engine Cover (Fig. 27). Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly.

Checking the fuel, cleaning the air filter, and adjusting the idle speed should solve most engine problems. If not and all of the following are true:

the engine will not idle

the engine hesitates or stalls on acceleration

there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

Crochet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Filter Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Filter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Idle Adjustment

Screw

 

Fig. 27

 

Muffler

Starter Housing

 

Cover

Screws (2)

 

 

 

Starter

 

Starter

Housing

 

Housing

Screws

 

 

(4)

Fig. 28

ROCKER ARM CLEARANCE

This requires disassembly of the engine. If you feel unsure or unqualified to perform this, take the unit to a qualified service dealer. NOTE: Inspect the valve to rocker arm clearance with a feeler

gauge after the first 10 hours of operation and every 40 hours of operation.

The engine must be cold when checking or adjusting the rocker arm clearance.

This task should be performed inside, in a clean, dust free area.

1.Remove the 2 muffler cover screws with a flat blade or T-25 Torx head screwdriver (Fig. 28), then remove the cover.

2.Remove the 6 starter housing screws with flat blade or T-25 Torx head screwdriver (Fig. 28), then remove the housing.

NOTE: Make sure to store the screws so that they can be reinstalled into their original holes.

3.Disconnect the spark plug wire.

4.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise.

5.Clean dirt from around the rocker arm cover. Remove the screw holding the rocker arm cover with a large flat blade screwdriver or Torx T-25 bit (Fig. 29). Remove the rocker arm cover and gasket.

6. Turn the flywheel slowly to bring the piston to the top of its travel (known as top dead center). Check that:

The piston is at the top of its travel while looking in the spark plug hole (Fig. 29)

Both rocker arms move freely, and both valves are closed.

If these statements are not true, repeat this step.

7.Slide the feeler gauge between the rocker arm and the valve return spring. Measure the clearance between the valve stem and rocker arm (Fig. 30 & 31). Measure both the intake and exhaust valves.

Rocker Arm

Spark Plug Cover

Hole

Fig. 29

Adjusting

INTAKE

Rocker Arms

O-Ring

 

 

EXHAUST

Feeler Gauge

 

Fig. 30

 

The recommended clearance for both intake and exhaust is .003 – .006 in. (.076 – 0.152 mm). Use a standard automotive .005 in. (0.127 mm) feeler gauge. The feeler gauge should slide between the rocker arm and valve stem with a slight amount of resistance, without binding. See Figures 30 and 31.

8.If the clearance is not within specification:

a.Turn the adjusting nut using a 5/16 inch (8 mm) wrench or nut driver (Fig. 31).

To increase clearance, turn the adjusting nut counterclockwise.

To decrease clearance, turn the adjusting nut clockwise.

b. Recheck both clearances, and adjust as necessary.

9.Reinstall the rocker arm cover using a new gasket (Fig. 29). Torque the screw to: 20–30 in•lb (2.2–3.4 N•m).

10.Check the spark plug and reinstall. See Replacing the Spark Plug.

11.Reinstall the spark plug wire.

12.Reinstall the engine cover. Check alignment of the cover before tightening the screws. Tighten screws.

Adjusting

Nut

.003–.006 in (0.076– 0.152 mm)

Culbuteur

Feeler

Gauge

Valve Stem

Fig. 31

NOTE: Make sure that the screws are reinstalled into their original holes (Fig. 28).

REPLACING THE SPARK PLUG

CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder.

Use a replacement part number 753-05784. The correct spark gap is

0.025 in. (0.635 mm.). Remove the plug after every 40 hours of 0.025 in.

operation and check its condition.

(0.635 mm)

1. Stop the engine and allow it to cool.

2. Remove the 2 plastic muffler cover screws with a flat blade or T-25 Torx head screwdriver (Fig. 28), then remove the cover.

3.Remove the 2 plastic and 4 aluminum starter housing screws

with flat blade or T-25 Torx head screwdriver (Fig. 28), then

 

 

 

Fig. 32

remove the housing.

 

 

 

 

 

NOTE: Make sure to store the screws so that they can be reinstalled into their original holes.

4.Grasp the plug wire firmly and pull the cap from the spark plug.

5.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise.

6.Replace cracked, fouled or dirty spark plug. Set the spark gap at 0.025 in. (0.635 mm.) using a feeler gauge (Fig. 32).

7.Install a correctly-gapped spark plug in the cylinder head. Turn the 5/8 in. socket clockwise until snug. If using a torque wrench, torque to: 110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

 

 

SPARK ARRESTOR MAINTENANCE

 

Muffler

 

 

 

 

WARNING: To avoid serious personal injury,

 

 

 

always turn your unit off and allow it to cool

 

Spark Arrestor

 

before you clean or do any maintenance on it.

 

Cover

1.

Remove the muffler cover. See Rocker Arm Clearance.

 

T-25

 

Screw

2.

With a flat blade screwdriver or Torx T-20 bit and a T-25 bit,

 

 

 

remove the screws attaching the spark arrestor diverter to the

 

 

 

muffler (Fig. 33).

 

 

3.

Remove the spark arrestor cover.

Spark Arrestor

 

4.

Remove the spark arrestor screen from the spark arrestor cover.

T-20 Screw

5.

Clean the spark arrestor screen with a wire brush or replace it.

Screen

 

Fig. 33

6.

Reinstall the spark arrestor screen, spark arrestor cover, and

 

 

screws.

 

 

7.

Reinstall the muffler cover.

 

 

CLEANING

WARNING: To avoid serious personal injury, always turn your unit off and allow it to cool before you clean or do any maintenance on it.

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.

STORAGE

Never store the unit with fuel in the tank where fumes may reach an open flame or spark.

Allow the engine to cool before storing.

Lock up the unit to prevent unauthorized use or damage.

Store the unit in a dry, well-ventilated area.

Store the unit out of the reach of children.

LONG TERM STORAGE

1.Drain all gasoline from the gas tank into a container. Do not use gas that has been stored for more than 60 days. Dispose of the old gasoline in accordance to Federal, State, and Local regulations.

2.Start the engine and allow it to run until it stalls. This ensures that all gasoline has been drained from the carburetor.

3.Allow the engine to cool. Remove the spark plug and put 5 drops of high quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the blower after storage.

4.Change the oil, referring to Changing the Oil. Dispose of the old oil in accordance to Federal, State and Local regulations.

5.Thoroughly clean the unit and inspect for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage.

TRANSPORTING

Allow the engine to cool before transporting.

Secure the unit while transporting.

Drain the gas tank before transporting.

Tighten gas cap before transporting.

SPECIFICATIONS

ENGINE*

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 cu. in. (25 cc) Blower Operating RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,000 rpm Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,200 – 4,400 rpm Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Momentary Switch Valve clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.003–0.006 in. (0.076–0.152 mm) Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Champion Spark Plug #RDZ4H or Similar Spark Plug Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 inch (0.635 mm) Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30 Oil Crankcase Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.03 oz (60 ml) Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded Carburetor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto Rewind Muffler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable Speed Fuel Tank Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 oz (414 ml)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

7

TROUBLESHOOTING

 

ENGINE WILL NOT START

 

 

ENGINE WILL NOT ACCELERATE

 

 

 

CAUSE

ACTION

 

CAUSE

ACTION

 

 

Empty fuel tank

Fill fuel tank with new fuel

 

Old fuel

Drain gas tank and add fresh fuel

 

 

 

 

 

 

 

 

 

Primer bulb wasn't pressed enough

Press primer bulb fully and slowly 10 times

 

Dirty air filter

Clean or replace the air filter

 

 

Old fuel

Drain gas tank and add fresh fuel

 

Plugged spark arrestor

Clean or replace spark arrestor

 

 

 

 

 

 

 

 

 

Fouled spark plug

Replace the spark plug

 

 

 

 

 

 

ENGINE LACKS POWER OR STALLS

 

 

 

Plugged spark arrestor

Clean or replace spark arrestor

 

 

 

 

 

CAUSE

ACTION

 

 

 

 

 

 

 

ENGINE WILL NOT IDLE

 

 

Old fuel

Drain gas tank and add fresh fuel

 

 

CAUSE

ACTION

 

 

 

 

 

 

Fouled spark plug

Replace the spark plug

 

 

 

 

 

 

 

Air filter is plugged

Replace or clean the air filter

 

Plugged spark arrestor

Clean or replace spark arrestor

 

 

 

 

 

 

 

Old fuel

Drain gas tank and add fresh fuel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: For questions, call 1-877-282-8684 in the United States and 1-800-668-1238 in Canada.

CALIFORNIA / EPA EMISSION CONTROL WARRANTY STATEMENT

Your Warranty Rights and Obligations

The California Air Resources Board, the Environmental Protection Agency, and Cub Cadet LLC (Cub Cadet) are pleased to explain the emission control system warranty on your 2007 and later small off-road engine. In California and the 49 states, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. Cub Cadet must warrant the emission control system on your small offroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel-injection system, the ignition system, and catalytic converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Cub Cadet will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

The 2007 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by Cub Cadet.

Owners Warranty Responsibilities

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s manual. Cub Cadet recommends that you retain all receipts covering maintenance on your small off-road engine, but Cub Cadet cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that Cub Cadet may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a Cub Cadet Authorized Service Center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-877-282-8684.

Manufacturer’s Warranty Coverage

The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and workmanship which cause the failure of a warranted part for a period of two years.

Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Cub Cadet Service Center. For the nearest location please contact Cub Cadet at: 1-877-282-8684.

Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any warranted part which is scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement point for that part.

The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an Authorized Cub Cadet Service Center.

The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

In order to file a claim, go to your nearest Authorized Cub Cadet Service Center. Warranty services or repairs will be provided at all Authorized Cub Cadet Service Centers.

Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer.

Emission Warranty Parts List:

The following components are included in the emission-related warranty of the engine: air filter, carburetor, primer, fuel lines, fuel pick up/ fuel filter, ignition module, spark plug, and muffler. Valves and Cam are additionally included if your engine is a 4-Stroke Model.

CALIFORNIA EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT

Your Warranty Rights and Obligations

The California Air Resources Board and Cub Cadet LLC (Cub Cadet) is pleased to explain the evaporative emission control system’s warranty on your 2007 model year and later small off-road (equipment type) engine. In California, new equipment that use small off-engines must be designed, built, and equipped to meet the State’s stringent anti-smog standards Cub Cadet must warrant the evaporative emission control system on your small off-road Lawn & Garden engine for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment.

Your evaporative emission control system may include parts such as: carburetors, fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other associated components. For engines less than or equal to 80 cc, only the fuel tank is subject to the evaporative emission control warranty requirements of this section. The displacement of your small off road engine is less than 80 cc.

Manufacturer’s Warranty Coverage

This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be repaired or replaced by Cub Cadet.

Owner’s Warranty Responsibilities

As the small off-road Lawn & Garden engine owner, you are responsible for performance of the required maintenance listed in your owner’s manual. Cub Cadet recommends that you retain all receipts covering maintenance on your Lawn & Garden Engine but Cub Cadet cannot deny warranty solely for the lack of receipts.

As the small off-road Lawn & Garden engine owner, you should however be aware that the Cub Cadet may deny you warranty coverage if your fuel tank has failed due to abuse, neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your Lawn & Garden fuel tank to Cub Cadet distribution center or service center as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact Cub Cadet at 1-877-282-8684.

Defects Warranty Requirements

(a)The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.

(b)General Evaporative Emissions Warranty Coverage. The fuel tank must be warranted to the ultimate purchaser and any subsequent owner that the evaporative emission control system when installed was:

(1)Designed, built, and equipped so as to conform with all applicable regulations; and

(2)Free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.

(c)The warranty on evaporative emissions-related parts will be interpreted as follows:

(1)Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for the warranty period defined in subsection (b)(2). If any such part fails during the period of warranty coverage, it must be repaired or replaced by Cub Cadet. Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining warranty period.

(2)Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty period defined in subsection (b)(2). A statement in such written instructions to the effect of “repair or replace as necessary” will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for a time not less than the remaining warranty period.

(3)Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced by the Cub Cadet. Any such part repaired or replaced under warranty must be warranted for a time not less than the remainder of the period prior to the first scheduled replacement point for the part.

(4)Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warranty station.

(5)Not withstanding the provisions of subsection (4) above, warranty services or repairs must be provided at distribution centers that are franchised to service the subject engines or equipment.

(6)The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station.

(7)Throughout the evaporative emission control system’s warranty period set out in subsection (b)(2), Cub Cadet must maintain a supply of warranted parts sufficient to meet the expected demand for such parts.

(8)Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the warranty obligations of the manufacturer issuing the warranty.

(9)The use of any add-on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article. The manufacturer issuing the warranty will not be liable under this Article to warrant failures of warranted parts caused by the use of an add-on or modified part.

(10)Cub Cadet shall provide any documents that describe the warranty procedures or policies within five working days of request by the Air Resources Board.

Emission Warranty Parts List

(1) Fuel Tank

Written instructions for the maintenance and use of the evaporative emissions control system by the owner shall be furnished with each new engine or equipment.

8

Manuel de l’utilisateur

Souffleuse à 4 temps à essence

HB425

NE RETOURNEZ

PAS CE PRODUIT

Pour une assistance, veuillez appeler le 1-877-282-8684

(E.U.) ou le 1-800-668-1238 (Canada)

ou visitez le site : www.cubcadetcommercial.com

CONSERVEZ CES INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-877-282- 8684 aux États-Unis ou le 1-800-668-1238 au Canada. Pour de plus amples informations à propos de votre appareil, visitez www.troybilt.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ QUI

VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS GARANTIE

NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS BREVETS

AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

Tout entretien effectué sur cet appareil pendant et après la période de garantie doit être fait par un concessionnaire agréé uniquement.

Avant d'assembler votre nouvel équipement, repérez la plaque signalétique de l'appareil et copiez ses informations dans l'espace cidessous. Ces informations sont essentielles si vous désirez obtenir de l'aide auprès de notre service technique ou d'un distributeur agréé. Un exemple de plaque signalétique est présenté ci-dessous.

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1 Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F2 Savoir votre unité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4 Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4 Informations sur l'huile et le carburant . . . . . . . . . . . . . . . . . . . . .F5 Instructions de démarrage et d'arrêt . . . . . . . . . . . . . . . . . . . . . . .F5 Instructions d’utilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6 Instructions d’entretien et réparations . . . . . . . . . . . . . . . . . . . . .F6 Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F7 Résolutions de problèmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F8 Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F8 Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E10–E11 Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . .Quatrième de couverture

Dans un effort de réduire l’impact sur les forets et réduire les émissions de gaz carbonique ainsi que les émissions de gaz à effet de serre, MTD utilise moins de papier en réduisant la taille du texte de ce manuel.

P/N 769-03822

 

MODEL :

S/N :

ITEM :

Copiez le numéro de modèle / pièce mère ici :

Copiez le numéro de série ici :

Toutes les informations, illustrations et spécifications contenues dans ce manuel tiennent compte des dernières informations techniques disponibles au moment de mettre sous presse. Nous nous réservons le droit d'y apporter des modifications à tout moment, sans préavis.

Copyright© 2008 MTD SOUTHWEST INC., Tous droits réservés.

(06/08)

Loading...
+ 19 hidden pages