Cub Cadet 53AJ8CTX750 User Manual

0 (0)
Cub Cadet 53AJ8CTX750 User Manual

Hydrostatic Zero-Turn

Commercial Riding Mower

Professional Turf Equipment

60” Fabricated Deck

Digital Fuel Injection,

Liquid Cooled

OPERATOR’S AND SERVICE MANUAL

TABLE OF CONTENTS

Foreword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Safety Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A.Danger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C.Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Related to Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 C.Related to Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 D. When Mowing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 E. Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 A. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 C.Initial Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 D. Zero Turn Break-In and Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 13 E. Mower Cutting Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 A. Mower Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 B. Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 C. Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 D. Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 E. Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 F. Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 G.Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Performance Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 A. High Speed Tracking Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 B. Engine RPM Check and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

C. Deck Corner Ball Wheel Roller Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 D. Deck Center Anti-Scalp Roller Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 E Lap Bar Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 F Deck Leveling Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Warranty

This product may be covered by one or more of the following patents:

D409,208; 5,946,894; 6,070,690; 6,301,864; 6,662,538; Pending

2

FORWARD

The Tank Hydrostatic Zero-Turn Commercial Riding Mower provides superb maneuverability, mid-mount cutting capability for professional landscapers, commercial lawn service companies, professional turf managers and golf course superintendents. The machine incorporates many safety features that should be studied by all operators and maintenance personnel before use. The list of safety precautions should receive particular attention.

This manual presents all of the operating and maintenance instructions necessary to keep your mower at peak efficiency. If operated and maintained properly, your mower will give dependable service.

CAUTION:

Only thoroughly trained persons should operate and maintain this mower. This machine can cause serious injury to anyone who misuses it and does not understand its operation. For their personal safety, all operators and maintenance personnel are required to read this entire manual before operating the mower.

Hazard control and accident prevention are partially dependent upon the design and configuration of the equipment. Notwithstanding, these factors are also dependent upon the awareness, concern, prudence and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment.

WARNING

The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered, or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California, the above is required by law (Section 4442 of the California Public Resources Code). Other States may have similar laws. Federal laws apply to federal lands. A spark arrester muffler may be available.

NOTE: The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications, warranty and service. Please refer to the engine manufacturer’s owner’s/operator’s manual, packed seperately with your unit, for more information.

MODELS LISTED IN THIS MANUAL

29HP Tank, 53AJ8CTX750

3

GENERAL SAFETY

OPERATIONS

A.DANGER

1.Do not operate machine in confined areas where exhaust gases can accumulate.

2.Do not operate machine without mower chute deflector in place and operational.

3.Do not carry passengers.

B.WARNING

1.Do not operate machines under the influence of alcohol or drugs.

2.Do not operate machines without all guards and safety devices in place and functional.

3.Do not start machines if there are fuel or oil leaks or spillage — clean it up.

4.Do not operate machines near spilled or leaking fuels.

5.Do not stop or park machine over dry leaves, grass, debris, etc. that could be combustible.

6.Use extreme care when backing up.

7.Do not operate machine on slopes greater than 15 degrees (27%), and always go across slopes, not up and down.

8.Do not operate machines on slopes when traction is reduced (wet grass, ice, soft ground, loose ground, leaves, pine needles, debris, etc.).

9.Avoid turning downhill if possible, go slowly and use extra care when turning downhill.

10.Do not operate machines during reduce visibility (low light, fog, rain, etc.).

11.Do not operate machines with non-approved attachments.

12.Do not operate machines that are damaged.....have machine repaired.

13.Do not operate machines that have not been properly maintained.

14.Use only replacement parts that are the same or equivalent to the original equipment.

15.Do not modify machines or any of their components, especially the engine governor!

16.Do not operate machine for more than 2 hours without hearing protection.

C.CAUTION

1.Use proper protective equipment when operating machine (gloves, boots, and hearing protection are recommended).

2.Read entire machine Operator’s Manual.

3.Make sure operators are fully trained in the safe use of the machine.

4.Follow all safety instructions when using the machine.

5.Keep all safety signs legible and properly installed.

6.Do not check for hydraulic leaks with any part of the body.

7.Do not add fuel to a machine when the engine is running and/or the exhaust system is hot.

8.Keep machine clean and free of debris, grass, leaves, oil, grease, etc.

9.Place lap bars in neutral/start position, set park brake, disengage P.T.O., turn engine off, and remove ignition key before you dismount from machine.

10.Use machines laterally or diagonally across slopes, avoid going downhill when possible.

11.Go slowly and use extra care when descending slopes.

12.Disengage P.T.O. when crossing surfaces such as asphalt, concrete, loose ground, sand, gravel, etc.

13.Use extra care when loading and unloading machines from trucks or trailers.

SAFETY PRECAUTIONS

A.General

1.Read this Operator’s Manual before starting the mower. Study the controls and learn the proper sequence of operation.

2.Do not allow anyone to operate or maintain this machine who has not read this manual. Never permit children to operate this machine.

3.Never carry passengers.

4.Do not remove any shields, guards or safety devices. If a shield, guard or safety device is damaged or does not function, repair or replace it before operating the mower.

5.Always wear safety glasses and safety shoes when operating or maintaining this mower. Do not wear loose-fitting clothing.

6.Disconnect the spark plug wires and remove the key from the ignition to prevent the engine from accidentally starting before performing any maintenance on this mower.

7.Never run the engine indoors without adequate ventilation. Exhaust fumes are deadly.

8.To avoid serious burns, do not touch the engine, exhaust pipe or muffler while the engine is running or until it has cooled after it has been shut off.

9.The liquid in the battery is dilute sulfuric acid. Always wear safety glasses and rubber gloves when working on the battery. Do not overfill the battery.

10.Lead-acid batteries generate hydrogen and oxygen gases which form an explosive mix-

4

ture. Keep sparks and flames away at all times.

11.When looking for oil leaks, never run your hand over hydraulic hoses, lines or fittings. Never tighten or adjust hydraulic hoses, lines or fittings while the system is under pressure. If high-pressure oil penetrates the skin, the oil must be removed within a few hours by a doctor familiar with this form of injury or serious complications may result.

B.Related to Fuel

1.Fuel is highly flammable and its vapors can explode if ignited. Please respect it.

2.Do not smoke or permit others to smoke while handling fuel.

3.Always use approved containers for fuel and fill slowly to decrease the chance of static electricity buildup and spillage.

4.Store fuel in well ventilated and unoccupied buildings away from sparks and flames.

5.When dispensing gasoline into approved containers, place the container on the ground when refueling to avoid a possible static electricity ignition of fuel vapors.

6.Do not fill containers while it is inside a vehicle, trunk, the bed of a pickup or floor of a trailer.

7.Always shut off the engine and permit it to cool before removing the fuel tank cap.

8.Always fill the fuel tank outdoors.

9.If the fuel container spout will not fit inside the fuel tank opening, use a funnel.

10.When filling the fuel tank, stop when the fuel reaches one inch from the top. This space is necessary for tank expansion. Do not overfill.

11.Wipe up any spilled fuel.

C. Related to Batteries

Batteries are stored electrical energy devices that may be serviceable with removable caps (the electrolyte levels can be checked), or may be non-service- able (no attempt should be made to open the vents).

Batteries may contain lead (Pb) and sulfuric acid, and they must be re-cycled and not disposed of nor abandoned. Sulfuric acid can cause severe burns, and in the event of contact, the areas should be flushed with water and a physician contacted. Battery cases should not be punctured. Lead is poisonous and is contained within the positive and negative terminals as well as within the battery’s internal gridwork of plates and active materials.

Explosive gases are generated when batteries are re-charged, so sparks, flames and heat sources should be avoided. Loose connections at the battery

terminals can produce sprks and heat...connections to the terminals must be kept tight, and the terminals and battery surfaces kept clean of acids and corrosion. If batteries are re-charged or “jumped” from external sources, make sure that the connections are made properly and in the correct sequence...connect to the positive terminal of the good battery first, then connect that to the positive terminal of the weak battery. The third connection should be to the negative terminal of the good battery, followed by the negative terminal of the weak battery. If sparks are observed or heating of the wiring or connectors is detected, disconnect in reverse order (I.E., the negative terminal of the weak battery first). Batteries should be recharged at a constant voltage...generally 14.5 +/- 0.5 volts DC for a nominal 12 volt DC battery.

D.When Mowing

1.Keep adults, children and pets away from the area to be mowed.

2.When operating this mower in the forward direction, DO NOT allow the steering levers to return to the neutral position on their own. Always maintain a firm grip on the levers, operate them smoothly and avoid any sudden movements of the levers when starting or stopping.

3.If the mower is equipped for side discharge, never use the mower without the discharge chute installed and placed in the down position.

4.Always remove debris and other objects from the area to be mowed.(Note: debris and loose grass will reduce traction.)

5.Mow only in daylight.

6.Watch for holes, sprinkler heads and other hidden hazards.

7.Avoid driving too close to trees, creeks, ditches, sand traps and other obstacles.

8.Before backing up, check behind you and watch where you’re going.

9.Always reduce speed when making a turn, and when grass is wet.

10.Always mow across slopes, never up and down the slope. Do not operate on steep slopes and slow down before turning.

11.Be careful when crossing gravel paths or roadways. Always turn off the blade clutch switch and wait until the blades stop rotating and raise the cutting deck to the transport position. Always allow other vehicles to have the right-of-way.

12.If you hit a solid object while mowing, turn off the blade clutch switch, place the left and right steering levers in the neutral position, move the throttle to slow, set the parking brake, shut off the engine and take the key from the ignition switch. Inspect for damage. Repair any

5

damage. Make sure the blades are in good condition and that the blade bolts are tight before restarting the engine.

13.Never leave the mower unattended without: turning off the blade clutch switch; placing the left and right steering levers in the neutral position; moving the throttle to slow; setting the parking brake; shutting off the engine and taking the key from the ignition switch.

14.Never walk or stand on the discharge side of a mower with the engine running. Turn off the blade clutch switch if another person approaches while you are operating the mower.

15.Never attempt to operate the traction unit without the mowing deck attached.

16.Keep the mower and especially the engine and hydraulic components clean and free of grease, grass and leaves to reduce the chance of fire and to permit proper cooling.

E.Towing

1.Tow only with a machine that has an approved hitch designed for towing. Do not attach towed equipment except at the hitch point.

2.Follow the manufacturers recommendation for weight limits for towed equipment and towing on slopes.

3.Never allow children or others in or on towed equipment.

4.On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

Note: 5 degrees (9%) maximum slope.

5.Travel slowly and allow extra distance to stop.

F.Operator Protection System -Foldable

1.This machine is equipped with an Operator

Protective System (OPS), which includes:

a.A Roll Over Protective Structure (ROPS) or Operator Protective Device (OPD) which may be of the fixed or folding configuration

b.Seat belt assembly with retractable function

2.ROPS and OPDs are structures designed to provide a crush-resistant space for the operator when properly seat-belted within the designated seating area of the machine in the event of a machine tip-over or roll-over. Folding ROPS and OPDs shall be used in their fully upright and locked configurations except in those circumstances whereby they need to be momentarily folded-down to avoid contact with items such as tree limbs, clothes lines, guy wires, buildings, etc. At other times and conditions, ROPS and OPDs shall be in their fully upright and locked configurations.

DANGER:

Damaged ROPS and OPDs must be replaced prior to operator use!

3.Seat belts shall be used and shall be properly fastened about the operator’s waist at all times, except when the ROPS or OPDs are:

-not properly installed and/or not properly secured onto the machine

-damaged in such manner that their structural integrity has been compromised

-not in their fully upright and locked position

4.Seat belts are attached to the movable portion of the seat when suspension seats are utilized, and therefore the seat-mounting base must be secured to its pivot means and the pivot means latched to the frame of the machine. Seat belts are attached to the seat or the frame of the machine when non-sus- pension (standard) seats are provided, however, if a suspension kit is added to a seat, the seat belt must be attached to the movable portion of the seat or suspension mechanism, the seat-mounting base must be secured to its pivot means, and the pivot means be latched to the frame of the machine.

DANGER:

If ROPS and OPDs are folded down or missing, seat belts shall not be fastened. Worn or damaged seat belt assemblies must be replaced prior to operator use.

5.Brush Guards and canopies can afford additional protection for the operator. The Brush Guard can deflect tree limbs, clothes lines, and other obstacles that otherwise could come in contact with the ROPS and OPDs. Contact of ROPS and OPDs by items such as tree limbs, clothes lines, guy wires, and buildings, could create hazardous conditions whereby the machine could experience a tipover or roll-over. The canopy can provide protection for the operator from some environmental exposure (sunlight, rain, etc.). Work lights may be available.

6.The ROPS and seat belt are integral parts of this machine and should not be tampered with, modified in any manner, or removed.

7.The ROPS extends above and behind the operator position, and therefore the operator must be aware of potential contact of the ROPS with items such as trees, buildings, doorways, clothes lines, utility wires, etc., that could cause the machine to upset or roll-

6

over....use caution in (or avoid) areas where the ROPS could come in contact with any structures, trees, etc.

8.The ROPS and seat belt add additional mass that elevates the machine’s Center of Gravity (C.G.) which negatively affects the machine’s stability and traction....use extra caution when operating on slopes.

9.Inspect the ROPS and seat belt assemblies on a regular basis for damage and improper operation....replace all components that are damaged or are not functioning properly with authorized replacement parts.

10.Failure to use the seatbelt properly could result in serious injury or death if an accidental overturn occurs. In order for the ROPS to be effective, the seat belt must be securely fastened around the operator at all times when the operator is on the machine. Contact with the ROPS during an overturn could cause serious injury or death.

11.The ROPS will not prevent the machine from upsets or roll overs.

12.Only approved attachments should be used on this machine.

G.Suspension Seat

1.This unit is equipped with an adjustable suspension seat system, which includes a foldforward seat with retractable seat belt assembly, a low profile mechanical suspension, and an Operator Presence Sensor (OPS).

2.The seat bottom is covered with a heavyduty vinyl fabric and integrates the EVC cushion comfort system that provides up to 1 3/8” dampered (for shock isolation) suspension travel. An OPS in the form of a switch, is integrated into the seat bottom and is connected to the machine electrical system. The seat back is also covered with a heavy-duty vinyl fabric, it adjusts to recline up to 16 degrees, and it will fold forward for transport or protection from the elements of weather (lever actuated on operator’s left side). The armrests are adjustable for operator comfort (knob inside armrests actuated from the bottom). Roller bearing single-locking tracks provide easy repositioning fore/aft up to 5” (lever actuated on lower right).

3.A mechanical suspension mechanism incorporates weight/ride adjustment controls for operators in the 125 to 275 lb. weight range (turn the knob on the front of the seat clockwise to increase the weight capacity and counter-clockwise to decrease. Self-lubricat-

ing bearings are utilized throughout the suspension mechanism that provides an additional 2” of suspension travel.

4.A retractable seat belt assembly with inertialock is attached to the “ride” portion of the seat frame. The seat frame is attached to the mechanical suspension, which is attached to the roller tracks that are bolted to the seat base in one of the three (3) locations - the seat assembly can be detached and reinstalled 1” forward or 1” aft from the factory installed position. When the two (2) hairpin clips are removed from the frame-mounted stud-bolts, the complete seat assembly and seat base can be pivoted forward onto the foot platform - this provides access to the battery, hydraulic reservoir and filter, as well as some of the electrical system and control linkages. The seat base must be secured with the hairpin clips prior to machine operation.

Note: The seat base must be secured by properly installing the hairpin clips into both frame-mounted stud-botls, otherwise, the seat assembly could tilt forward. The Operator Presence Sensor must be connected to the

electrical wiring harness.

7

SAFETY DECALS AND LABELS

WARNING

SHIELD MISSING DO NOT OPERATE

TO REDUCE THE RISK OF INJURY, D O N O T O P E R A T E M O W E R U N L E S S DISCHARGECHUTECOVEROR GRASS C A T C H E R IS I N I T S P R O P E R P L A C E .

D A N G E R

K E E P H A N D S a n d FE E T A W A Y

Part Number: 00030635

Part Number: 01002166

DANGER

R O T A T I N G B L A D E

Do not put hands or feet under or into mower when engine is running.

Part Number: 777S32840

Part Number: 00030633

Part Number: 777S32797

Part Number: 02003514

! WARNING!

Maximum weight on hitch is 50 lbs.

Maximum towed load is 500 lbs.

Never allow passengers on towed equipment.

Loss of traction can occur on slopes, 5(9%) maximum grade.

Travel slowly and allow extra distance to stop.

Use caution during turns to avoid jack-knifing.

Use extra caution when operating in reverse.

Do not modify hitch or repair hitch. Replace hitch if damaged.

Part Number: 02003652

Part Number: 02002693

8

SPECIFICATIONS

GENERAL INFO.

 

Controls:

Engine ignition and start switch; throttle; left and right steering

 

levers; electric blade clutch switch; parking brake; mower deck lift

 

 

Parking Brake:

Mechanical linkage attached to the brake handle and drum

 

brakes

 

 

Seat:

Adjustable seat with armrests. 5" Adjustment fore & aft

 

 

Frame:

2" Steel square tube and plate, all welded construction

 

 

Instrumentation:

Hourmeter, Tachometer, Maintenance-minder

Front Caster Wheels:

13 x 6.50 x 6

 

 

Drive Wheels:

60" deck, 24x12 - 12

 

 

Tire Pressure:

8-10 psi Rear, 20-25 psi front caster

Fuel Tank:

Two 6.5 gallon w/ shutoff valves

 

 

Ground Speed:

0-10 + MPH forward. 0-4 MPH reverse

 

 

Net Weight:

1170 lbs. w/60" deck

 

 

ENGINE INFO.

 

 

 

Engine:

29HP, Digital Fuel Injection, Liquid-Cooled, OHV, Kawasaki

Type:

Horizontal Crankshaft, V-Twin

 

 

Air Cleaner:

Dual Element, Canister Type

 

 

Lube System:

Pressurized with oil filter

Hydraulic System:

4 quart capacity, One quart filter

 

 

Starter:

12-volt electric

 

 

Blade Brake Clutch:

Electric

 

 

TRACTION DRIVE INFO.

 

 

 

Traction Drive:

Variable-speed hydrostatic pumps and hydraulic wheel motors for

 

each drive wheel

 

 

 

 

CUTTER DECK INFO.

 

 

 

Cutter Deck;Drive:

60” Belt Driven

 

 

Deck Lift:

Hand lever w/pin lock for height adjustment & foot pedal assist

Cutting Height:

1-1/2" to 5"

 

 

No. of Blades

3, attach to spindle with 3/4” bolts

 

 

Deck Spindles:

1-1/4” diameter tapered-roller bearings, aluminum housing

9

OPERATING INSTRUCTIONS

Figure. 1

Figure. 2

Hour Meter

(tach optional) Electric Blade Clutch Switch

indicator lights

Ignition Switch

Engine throttle

 

 

 

A.General

1.When Mowing:

a.Keep adults, children, and pets away from the area to be mowed.

b.When operating this mower, in the forward direction, do not allow the steering levers to return to Neutral on their own. Always maintain a firm grip on the levers, operate them smoothly and avoid any sudden movements of the levers when starting and stopping.

c.If the mower is equipped for side discharge, never use the mower without the discharge chute installed and placed in the down position.

d.Always remove debris and other objects from the area to be mowed (Note: debris and loose grass will reduce traction).

e.Mow only in daylight.

f.Watch for holes, sprinkler heads, and other hidden hazards.

g.Avoid driving too close to trees, creeks, ditches, sand traps, and other obstacles.

h.Before backing up, check behind and watch where you are going.

i.Always reduce speed when making a turn, and when grass is wet.

j.Always mow across slopes, never up and down the slope. Do not operate on steep slopes and slow down before turning.

Avoid turning downhill if possible, start at the bottom and work up to the top. Use extra care and go slowly when turning downhill. Control the speed and direction of the zero turn machine “primarily” with the speed/directional control (lap bar) of the downhill side of the machine...I.E.,

Parking Brake

maintain the uphill side lap bar “essentially” in a fixed position.

k.Be careful when crossing gravel paths or roadways. Always turn off the blade clutch switch and wait until the blades stop rotating and raise the cutting deck to the transport position. Always allow other vehicles to have the right of way.

l.If you hit a solid object while mowing, turn off the blade clutch switch, place the steering levers in the neutral position, move the throttle to slow, set the parking brake, shut off the engine, and take the key from the ignition switch. Inspect for damage. Repair the damage. Make sure the blades are in good condition and that the blade bolts are tight before restarting the engine.

m.Never leave the mower unattended without observing the following: turn off the blade clutch switch, placing the steering levers in the position, moving the throttle to slow, setting the parking brake, shutting off the engine and taking the key from the ignition switch.

n.Never walk or stand on the discharge side of the mower when the engine is running. Turn off the blade clutch switch if another person approaches while you are operating the mower.

o.Never attempt to operate the traction unit without having the mowing deck attached.

p.Keep the mower and especially the engine and hydraulic components clean and free

10

Loading...
+ 22 hidden pages