Cub Cadet 454 User Manual

0 (0)

Operator’s Manual

Rear Tine Tiller

Model 454

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

PRINTED IN U.S.A.

FORM NO. 770-10101E.fm

 

(12/2003)

TABLE OF CONTENTS

Content

Page

Content

Page

Important Safe Operation Practices

3

Servicing Your Tiller

11

Loose Parts

5

Maintaining Your Tiller

11

Assembling Your Tiller

6

Off Season Storage

12

Know Your Tiller

8

Trouble Shooting Guide

13

Operating Your Tiller

9

Illustrated Parts

14

Making Adjustments

10

Warranty

20

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new tiller. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. A sample model plate is also given below. You can locate the model plate by standing at the operating position and looking down at the center of the rear tine cover. This information will be necessary to use the manufacturer’s web site and/or to obtain help from the Customer Dealer Referral Line or an authorized service dealer.

Copy the model number here:

Copy the serial number here:

CUB CADET LLC

P. O. BOX 361131

www.cubcadet.com CLEVELAND, OH 44136

DEALER LOCATOR PHONE NUMBER: 877-282-8684

CUSTOMER SUPPORT

Please do NOT return the unit to the retailer from where it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, you can seek help from the experts. Choose from the options below:

Visit cubcadet.com for many useful suggestions. Click on Customer Support button and you will get the three options reproduced here. Click on the appropriate button and help is immediately available.

The answer you are

 

The answer you are

looking for could be just

 

looking for could be just

a mouse click away!

 

a mouse click away!

 

 

 

To reach the Customer Dealer Referral Line, please call 1-877-282-8684.

The engine manufacturer is responsible for all engine-related issues with regards to

Engine

Manual performance, power-rating, specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with your unit, for more information.

2

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

TRAINING

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

PREPARATION

1.Thoroughly inspect the area where the equipment is to be used. Remove all stones, sticks, wire, and other foreign objects which could be tripped over and cause personal injury.

2.Wear sturdy, rough-soled work shoes and closefitting slacks and shirts. Loose fitting clothes or jewelry can be caught in movable parts. Never operate this machine in bare feet or sandals.

3.Disengage clutch levers and shift (if provided) into neutral (N) before starting the engine.

4.Never leave this machine unattended with the engine running.

5.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

6.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add while the engine is hot or running.

e.Allow engine to cool at least two minutes before refueling.

f.Never over fill fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.)

j.To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil fuel spillage and remove any fuel soaked debris.

k.Allow machine to cool at least 5 minutes before storing.

OPERATION

1.Do not put hands and feet near rotating parts. Contact with the rotating parts can amputate fingers, hands, and feet.

2.Do not operate machine while under the influence of alcohol or drugs.

3.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles.

3

4. Keep bystanders, helpers, pets, and children at

 

Inspect thoroughly for damage. Repair any damage

least 75 feet from the machine while it is in

 

before starting and operating.

operation. Stop the machine if anyone enters the

18. Keep all shields, guards and safety devices in place

area.

 

and operating properly.

5. Be careful when tilling in hard ground. The tines

19. Never pick up or carry machine while the engine is

may catch in the ground and propel the tiller

 

running.

forward. If this occurs, let go of the handlebars and

20. Use only attachments and accessories approved

do not restrain the machine.

 

by the manufacturer. Failure to do so, can result in

6. Exercise extreme caution when operating on or

 

personal injury.

crossing gravel surfaces. Stay alert for hidden

21. If situations occur which are not covered in this

hazards or traffic. Do not carry passengers.

 

manual, use care and good judgment. Contact your

7. Never operate the machine at high transport

 

dealer for assistance. Telephone 1-877-282-8684

speeds on hard or slippery surfaces.

 

for the name of your nearest dealer.

8. Exercise caution to avoid slipping or falling.

Maintenance And Storage

9. Look down, behind, and use care when in reverse

or pulling machine towards you.

1.

Never tamper with safety devices. Check their

10. Start the engine according to the instructions found

 

proper operation regularly.

in this manual and keep feet well away from the

 

2.

Check bolts and screws for proper tightness at

tines at all times.

 

frequent intervals to keep the machine in safe

11. After striking a foreign object, stop the engine,

 

 

working condition. Also, visually inspect machine

disconnect the spark plug wire and ground against

 

 

for any damage.

the engine. Thoroughly inspect the machine for any

 

3.

Before cleaning, repairing, or inspecting, stop the

damage. Repair the damage before starting and

 

engine and make certain the tines and all moving

operating.

 

 

parts have stopped. Disconnect the spark plug wire

12. Disengage all clutch levers and stop engine before

 

 

and ground it against the engine to prevent

you leave the operating position (behind the

 

 

unintended starting.

handles). Wait until the tines come to a complete

 

4.

Do not change the engine governor settings or

stop before unclogging the tines, making any

 

over-speed the engine. The governor controls the

adjustments, or inspections.

 

 

maximum safe operating speed of the engine.

13. Never run an engine indoors or in a poorly

 

5.

Maintain or replace safety and instruction labels, as

ventilated area. Engine exhaust contains carbon

 

necessary.

monoxide, an odorless and deadly gas.

 

6.

Follow this manual for safe loading, unloading,

14. Muffler and engine become hot and can cause a

 

transporting, and storage of this machine.

burn. Do not touch.

 

7.

Never store the machine or fuel container inside

15. Use caution when tilling near fences, buildings and

 

where there is an open flame, spark or pilot light

underground utilities. Rotating tines can cause

 

 

such as a water heater, furnace, clothes dryer etc.

property damage or personal injury.

 

8.

Always refer to the operator’s manual for proper

16. Do not overload machine capacity by attempting to

 

instructions on off-season storage.

till soil to deep at to fast of a rate.

 

9.

If the fuel tank has to be drained, do this outdoors.

17. If the machine should start making an unusual

 

 

noise or vibration, stop the engine, disconnect the

10. Observe proper disposal laws and regulations for

spark plug wire and ground it against the engine.

gas, oil, etc. to protect the environment.

WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

NOTE: Not all safety labels shown may apply to your tiller.

WARNING

Hot surfaces can cause severe burns.

Do not touch

S30647

muffler or

 

adjacent areas.

WARNING

DEPTH

C

U

STAKE

T

 

TRANSPORT

O

1"

U

3"

5"

T

7"

KEEP AWAY FROM

ROTATING TINES.

ROTATING TINES

WILL CAUSE INJURY.

S32146

WARNING

TO AVOID SERIOUS INJURY

1.READ THE OPERATOR'S MANUAL.

2.KNOW LOCATION AND FUNCTIONS OF ALL CONTROLS.

3.KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

4.NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

5.SHUT OFF ENGINE BEFORE UNCLOGGING TINES OR MAKING REPAIRS.

6.KEEP BYSTANDERS AWAY FROM MACHINE.

7.KEEP AWAY FROM ROTATING PARTS.

8.USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

4

SECTION 2: LOOSE PARTS

Handle

Assembly

 

Depth

Control

Stake

Rod

Assembly

NOTE: Cable tie not shown.

5

Cub Cadet 454 User Manual

SECTION 3: ASSEMBLING YOUR TILLER

IMPORTANT:This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations.

NOTE: Left and right is determined from the operator’s position, standing behind the tiller.

Tools Required For Assembly

Adjustable Wrenches

Pair of Pliers

Screw Driver

To Remove Unit From Carton

Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

Remove loose parts included with unit (i.e., operator’s manual, etc.).

Cut corners and lay carton down flat.

Remove packing material.

Roll or slide unit out of carton. Check carton thoroughly for loose parts.

Extend control cable and lay on the floor. Be careful not to bend or kink control cable.

Attaching Depth Stake Assembly

Tip the tiller forward so it rests on front bumper.

Raise the tine shield hinge flap assembly. Remove "T" knob, flat washer and hex bolt from depth stake. Insert the depth stake assembly in front of spacer (under the tine shield) and up through the tine shield assembly as shown in Figure 1.

T-Knob

Hex Bolt

 

 

 

T-Knob

 

 

Hex Bolt

 

Depth

Washer

Washer

Stake

Clevis Pin

 

 

Hairpin Clip

Depth Stake

 

Figure 1

Insert clevis pin through the tine shield and the second hole from top of the depth stake. Secure with hairpin clip.

Insert hex bolt into the top hole of the depth stake assembly. Place flat washer on hex bolt and thread “T” knob onto the hex bolt. See Figure 1. Tighten securely.

Tip the tiller back down so it rests on the depth stake (transport position).

Attaching The Handle Assembly

Remove

Handle

Ass’y

Handle

Bracket

Figure 2

Remove top two bolts and flange lock nuts from handle mounting brackets as shown in Figure 2. Do not remove the bottom bolt and nut.

Place handle assembly in position between the handle mounting brackets. See Figure 2.

Line up holes in handle with holes in handle mounting brackets. Secure with hardware removed in step 1.

Attaching The Clutch Cable

Attach the clutch cable to the handle as follows (be careful not to kink the cable).

Remove threaded eyebolt and nut from the end of the cable.

Route the clutch cable to the right side of the handle mounting brackets and underneath the handle.

6

Loading...
+ 14 hidden pages