Cub Cadet 2164 User Manual

0 (0)

OPERATOR’S MANUAL

2000 TRACTOR

Model Number 2164

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368023 Cleveland, Ohio 44136-9723.

CUB CADET P.O. BOX 368023 CLEVELAND, OHIO 44136-9723

PRINTED IN U.S.A.

FORM NO. 770-10170B

 

(7/99)

BRIGGS & STRATTON CORP., FEDERAL (U.S. EPA) AND CALIFORNIA

EMISSION CONTROL SYSTEMS WARRANTY

(Owner’s Defect Warranty Rights and Obligations)

In the interest of the environment, Briggs & Stratton engines that meet strict emission requirements are labeled, “This engine conforms to 1995 - 1998 California emission regulations for ULGE engines and U.S. EPA Phase I regulations for small non-road engines.” EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND USED ELSEWHERE IN THE UNITED STATES

CALIFORNIA AND UNITED STATES EMISSION CONTROL DEFECTS WARRANTY STATEMENT

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Briggs & Stratton are pleased to explain the Emission Control Systems Warranty on your 1996 and later utility or lawn and garden equipment (ULGE) engine. In California, new ULGE engines produced on or after August 1, 1995 must be designed, built and equipped to meet the State’s stringent anti-smog standards. Elsewhere in the United States, new nonroad, spark-ignition engines certified for model year 1997 and later, must meet similar strandards set forth by the U.S. EPA. Briggs & Stratton must warrant the emission control system on your engine for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your ULGE engine.

Your emission control system includes such parts as the carburetor, air cleaner, ignition system, muffler and catalytic converter. Also included may be connectors and other emission related assemblies.

Where a warrantable condition exists, your authorized dealer or a Briggs & Stratton service dealer will repair your ULGE engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts and labor.

EMISSION CONTROL DEFECTS WARRANTY COVERAGE

The utility or lawn and garden equipment engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any covered part on your engine is defective, the part will be repaired or replaced by your authorized dealer or a Briggs & Stratton service dealer.

OWNER’S WARRANTY RESPONSIBILITIES

As the utility or lawn and garden equipment owner, you are responsible for the performance of the required maintenance listed in the Operator’s Manual. The engine manufacturer recommends that you retain all receipts covering maintenance on your ULGE engine, but the engine manufacturer cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the utility or lawn and garden equipment owner, you should however be aware that the engine manufacturer may deny you warranty coverage if your ULGE engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your utility or lawn and garden equipment engine to your authorized dealer or a Briggs & Stratton service dealer as soon as a problem exists. The undisputed warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your authorized dealer.

The emission warranty is a defects warranty. Defects are judged on normal engine performance. The warranty is not related to an in-use emission test.

EMISSION CONTROL DEFECTS WARRANTY PROVISIONS

The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the manufacturer’s engine warranty.

1.Warranted Parts — Coverage under this warranty extends only to the parts listed below (the emission control systems parts) to the extent these parts were present on the engine purchased.

a.Fuel Metering System

Cold start enrichment system (soft choke)

Carburetor and internal parts

Fuel pump

b.Air Induction System

Air cleaner

Intake manifold

c.Ignition System

Spark plug(s)

Magneto ignition system

d.Catalyst System

Catalytic converter

Exhaust manifold

Air injection system or pulse valve

e.Miscellaneous Items Used in Above Systems

Vacuum, temperature, position, time sensitive valves and switches

Connectors and assemblies

2.Length of Coverage — The engine manufacturer warrants to the initial owner and each subsequent purchaser that the Warranted Parts shall be free from defects in materials and workmanship which caused the failure of the Warranted Parts for a period of two years from the date the engine is delivered to a retail purchaser.

3.No Charge — Repair or replacement of any Warranted Part will be performed at no charge to the owner, including diagnostic labor which leads to the determination that a Warranted Part is defective, if the diagnostic work is performed at your authorized dealer or an authorized Briggs & Stratton service dealer. For emission warranty service contact your nearest authorized dealer or Briggs & Stratton service dealer as listed in the “Yellow Pages” under “Engines, Gasoline,” “Gasoline Engines,” “Lawn Mowers,” or similar category.

4.Claims and Coverage Exclusions — Warranty claims shall be filed in accordance with the provisions of the Engine Warranty Policy. Warranty coverage shall be excluded for failures of Warranted Parts which are not original Briggs & Stratton parts or because of abuse, neglect or improper maintenance as set forth in the Engine Warranty Policy. Briggs & Stratton is not liable to cover failures of Warranted Parts caused by the use of add-on, non-original, or modified parts.

5.Maintenance — Any Warranted Part which is not scheduled for replacement as required maintenance or which is scheduled only for regular inspection to the effect of “repair or replace as necessary” shall be warranted as to defects for the warranty period. Any Warranted Part which is scheduled for replacement as required maintenance shall be warranted as to defects only for the period of time up to the first scheduled replacement for that part. Any replacement part that is equivalent in performance and durability may be used in the performance of any maintenance or repairs. The owner is responsible for the performance of all required maintenance, as defined in the Operator’s Manual.

6.Consequential Coverage — Coverage hereunder shall extend to the failure of any engine components caused by the failure of any Warranted Part still under warranty.

2

CONTENTS

Section

 

Page

Section

Page

 

Emission Control Systems Warranty ...

2

VII Mowing.................................................

47

 

Tractor and Deck Preparation..............

3

Optional Equipment and Accessories .

48

 

Safe Operation Practices.....................

4

Maintenance Chart...............................

49

 

Product Graphics .................................

7

Trouble Shooting..................................

50

 

To The Owner......................................

8

Lubrication Table .................................

52

 

Serial No. Location ..............................

8

Lubrication Guide.................................

53

I

Controls and Indicators........................

9

Specifications.......................................

56

II

Operation .............................................

14

Slope Gauge ........................................

57

III

Adjustments .........................................

19

Warranty — Commercial Use .............

58

IV

Maintenance ........................................

25

Warranty — Residential Use ...............

59

V

Mower Deck.........................................

34

Maintenance Parts Chart ....................

60

VI

Off-Season Storage .............................

46

 

 

TRACTOR AND DECK PREPARATION

1. ATTACHING THE CHUTE DEFLECTOR

For shipping purposes, the mulching plug has been installed in the mower deck. The mulching plug must be removed to install the chute deflector assembly.

WARNING

Do not operate the mower deck, even with the mulching plug installed, unless the chute defelector has been properly installed.

1.Remove the wing nut, press the 1/4” screw down through the deck and withdraw the mulching plug from the discharge chute of the deck.

HEX NUTS

WING NUT

BELL

WASHERS

 

CHUTE

 

DEFLECTOR

1/4" SCREW

HEX CAP

 

MULCHING

SCREWS

 

PLUG

 

2.Remove the hex cap screws, bell washers and hex nuts installed in the deck at the chute opening.

3.Proper placement of the chute deflector will cover up the warning label on the chute opening. Place the deflector in position as shown. Install the hex cap screws from the underside of the deck and secure with the bell washers and hex nuts. Note: the crowned (rounded) surface of the washers go toward the hex nuts.

4.Refer to SECTION V-MOWER DECK when reinstalling the mulching plug.

2. CONNECT THE BATTERY

The tractor is shipped with an activated sealed battery. The positive battery cable has been connected at the factory, but the negative cable must be connected.

Note: Make sure the ignition switch is in the "OFF" position before attaching the battery cables.

1.Pull the protective cap off the negative terminal of the battery, and remove the hex cap screw and nut from the free end of the negative battery cable.

2.Connect the negative battery cable (heavy black) and ground wire (green) to negative terminal (—) of the battery using the hex cap screw and nut.

3.Slide the black terninal cover over the negative terminal of the battery.

3

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered, or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California, the above is required by law (Section 4442 of the California Public Resources Code). Other States may have similar laws. Federal laws apply to federal lands. A spark arrester muffler is available at your nearest engine authorized service center.

IMPORTANT

SAFE OPERATION PRACTICES

 

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL— HEED ITS WARNING.

Your lawn mower was built to be operated according to the rules for safe operation

in this manual. As with any type of power equipment, carelessness or error on the DANGER part of the operator can result in injury. This lawn mower is capable of amputating

hands and feet or throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

I. GENERAL OPERATION

1.Read, understand and follow all instructions in the manual and on the machine before starting. Keep this manual in a safe place for future and regular reference and for ordering replacement parts

2.Only allow responsible individuals familiar with the instructions to operate the machine. Know the controls and how to stop the machine quickly.

3.Do not put hands or feet under the cutting deck or near rotating parts.

4.Clear the area of objects such as rocks, toys, wire, etc. which could be picked up and thrown by the blades. A small object may have been overlooked and could be accidentally thrown by the mower in any direction and cause injury to you or a bystander. To help avoid a thrown objects injury, keep children, animals, bystanders and helpers at least 75 feet from the mower while it is in operation. Always wear safety glasses with side shields or safety goggles during operation or while performing an adjustment or repair, to protect eyes from foreign objects. Stop the blades when crossing gravel drives, walks or roads.

5.Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

6.Never carry passengers.

7.Disengage the blades before shifting into reverse and backing up. Always look down and behind before and while backing.

8.Be aware of the mower and attachment discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the chute guard in place.

9.Slow down before turning. Operate the machine smoothly. Avoid erratic operation and excessive speed.

10.Never leave a running machine unattended. Always turn off the blades, place the transmission in neutral, set the parking brake, stop the engine and remove key before dismounting.

11.Turn off blades when not mowing.

12.Stop the engine and wait until the blades come to a complete stop before (a) removing the grass catcher or unclogging chute, or (b) making any repairs, adjusting or removing any grass or debris.

4

13.Mow only in daylight or good artificial light.

14.Do not operate the machine while under the influence of alcohol or drugs.

15.Watch for traffic when operating near or crossing roadways.

16.Use extra care when loading or unloading the machine into a trailer or truck. This unit should not be driven up or down a ramp onto a trailer or truck under power, because the unit could tip over causing serious personal injury. The unit must be pushed manually on a ramp to load or unload properly.

17.Never make a cutting height adjustment while the engine is running if the operator must dismount to do so.

18.Wear sturdy, rough-soled work shoes and closefitting slacks and shirts. Do not wear loose fitting clothes or jewelry. They can be caught in moving parts. Never operate a unit in bare feet, sandals or sneakers.

19.Check overhead clearance carefully before driving under power lines, wires, bridges or low hanging tree branches, before entering or leaving buildings, or in any other situation where the operator may be struck or pulled from the unit, which could result in serious injury.

20.Disengage all attachment clutches, thoroughly depress the brake pedal and shift into neutral before attempting to start the engine.

21.Your mower is designed to cut normal residential grass of a height no more than 10”. Do not attempt to mow through unusually tall, dry grass (e.g. pasture) or piles of dry leaves. Debris may build up on the mower deck or contact the engine exhaust presenting a potential fire hazard.

22.Use only accessories approved for this machine by Cub Cadet. Read, understand and follow all instructions provided with the approved accessory.

II. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this manual to measure slopes before operating this unit on a sloped or hilly area. If the slope is greater than 15° as shown on the slope gauge, do not operate this unit on that area or serious injury could result.

DO:

Mow up and down slopes, not across.

Remove obstacles such as rocks, limbs, etc.

Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

Use slow speed. Choose a low enough gear so that you will not have to stop or shift while on the slope. Always keep the machine in gear when going down slopes to take advantage of engine braking action.

Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments. These can change the stability of the machine.

Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Rapid engagement or braking could cause the front of the machine to lift and rapidly flip over backwards, which could cause serious injury.

Avoid starting or stopping on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.

DO NOT:

Do not turn on slopes unless necessary; then, turn slowly and gradually downhill, if possible.

Do not mow near drop-offs, ditches or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

Do not mow on wet grass. Reduced traction could cause sliding.

Do not try to stabilize the machine by putting your foot on the ground.

Do not use the grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

1.Keep children out of the mowing area and in watchful care of an adult other than the operator.

2.Be alert and turn the machine off if children enter the area.

3.Before and when backing up, look behind and down for small children.

4.Never carry children, even with the blades off. They may fall off and be seriously injured or may interfere with safe machine operation.

5

5.Never allow children under 14 years old to operate the machine. Children 14 years and over should only operate the machine under close parental supervision and proper instruction.

6.Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure your vision of a child or other hazard.

7.Remove the key when the machine is left unattended to prevent unauthorized operation.

IV. SERVICE

1.Use extreme care in handling gasoline and other fuels. They are extremely flammable and the vapors are explosive.

a.Use only an approved container.

b.Never remove fuel cap or add fuel with the engine running. Allow the engine to cool at least two minutes before refueling.

c.Replace the fuel cap securely and wipe off any spilled fuel before starting the engine as it may cause a fire or explosion.

d.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

e.Never refuel the machine indoors because fuel vapors will accumulate in the area.

f.Never store the fuel container or machine inside where there is an open flame or spark, such as a gas hot water heater, space heater or furnace.

2.Never run a machine inside a closed area.

3.To reduce fire hazard, keep the machine free of grass, leaves or other debris build-up. Clean up oil or fuel spillage. Allow the machine to cool at least 5 minutes before storing.

4.Before cleaning, repairing or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the spark plug to prevent accidental starting.

5.Check the blade and engine mounting bolts at frequent intervals for proper tightness. Also visually inspect blades for damage (e.g., excessive wear, bent, cracked). Replace with blades which meet original equipment specifications.

6.Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.

7.Never tamper with safety devices. Check their proper operation regularly. Use all guards as instructed in this manual.

8.After striking a foreign object, stop the engine, remove the wire from the spark plug and thoroughly inspect the mower for any damage. Repair the damage before restarting and operating the mower.

9.Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. For your safety protection, frequently check the components and replace with manufacturer’s recommended parts when necessary.

10.Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when servicing blades.

11.Check brake operation frequently. Adjust and service as required.

12.Muffler, engine and belt guards become hot during operation and can cause a burn. Allow to cool down before touching.

13.Do not change the engine governor settings or overspeed the engine. Excessive engine speeds are dangerous.

14.Observe proper disposal laws and regulations. Improper disposal of fluids and materials can harm the environment and the ecology.

a.Prior to disposal, contact your local Environmental Protection Agency to determine the proper method for disposing of the waste. Recycling centers are established to properly dispose of materials in an environmentally safe fashion.

b.Use proper containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them. Properly dispose of the containers immediately following the draining of fluids.

c.DO NOT pour oil or other fluids into the ground, down a drain or into a stream, pond, lake, or other body of water. Observe Environmental Protection Agency regulations when disposing of oil, fuel, coolant, brake fluid, filters, batteries, tires and other harmful waste.

15.We do not recommend the use of a pressure washer or garden hose to clean your unit. They may cause damage to electrical components; spindles; pulleys; bearings; or the engine. The use of water will result in shortened life and reduce serviceability.

WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

6

Cub Cadet 2164 User Manual

PRODUCT GRAPHICS

Keep product safety graphics (decals) clean. Replace any safety graphic that is damaged, destroyed, miss-

ing, painted over or can no longer be read. Replacement safety graphics are available through your dealer.

STARTING INSTRUCTIONS

1.BE FAMILIAR WITH CONTROLS BEFORE STARTING ENGINE AND OPERATING.

2.SET CHOKE, MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL.

3.TURN KEY TO THE START POSITION.

4.AFTER ENGINE STARTS OPEN CHOKE.

STOPPING INSTRUCTIONS

1.DISENGAGE PTO AND SET PARKING BRAKE.

2.MOVE THROTTLE CONTROL TO MID POSITION AND TURN KEY OFF.

!WARNING

AVOID SERIOUS INJURY OR DEATH.

READ OPERATORS MANUAL AND ALL WARNING LABELS BEFORE USING MACHINE.

GO UP AND DOWN SLOPES, NOT ACROSS.

AVOID SUDDEN TURNS.

DO NOT OPERATE UNIT WHERE IT COULD SLIP OR TIP.

IF MACHINE STOPS GOING UPHILL, STOP PTO AND BACK DOWN HILL SLOWLY.

DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.

NEVER CARRY CHILDREN.

LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.

KEEP SAFETY DEVICES [GUARDS, SHIELDS, AND SWITCHES] IN PLACE AND WORKING.

REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADES.

KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

BE SURE THE BLADES AND THE ENGINE ARE STOPPED BEFORE PLACING HANDS OR FEET NEAR BLADES.

BEFORE LEAVING OPERATOR'S POSITION, DISENGAGE PTO, ENGAGE BRAKE LOCK, SHUT OFF ENGINE AND REMOVE KEY.

GENERAL SAFETY INSTRUCTIONS WARNING – LOCATED ON RIGHT SIDE OF RUNNING BOARD

HANDS AND FEET SAFETY GRAPHIC– LOCATED ON DEFLECTOR CHUTE

SAFETY GRAPHIC – LOCATED ON LEFT SIDE OF MOWER DECK

SAFETY GRAPHIC – LOCATED ON RIGHT SIDE OF DECK

DEFLECTOR SAFETY GRAPHIC–

LOCATED ON DECK

SAFETY GRAPHIC – LOCATED ON LEFT SIDE OF DECK

7

TO THE OWNER

Cub Cadet tractor Model 2164 is equipped with a 42inch mower deck and shipped with a mulching kit. The information in this manual has been prepared in detail to help you better understand the correct operation and maintenance of this equipment. Before you operate the tractor, study this manual carefully. Additional copies may be ordered from your dealer at a nominal price

Your local authorized dealer is interested in the performance you receive from your tractor. The dealer has trained service personnel who are familiar with the latest servicing information, with modern tools and original-equipment service parts which assure proper fit and good performance.

If you have difficulties with the unit, have any question regarding the operation or maintenance of this equipment, or desire additional information not found in this manual, contact your dealer. If you need help locating a dealer in your area, contact the Customer Dealer Referral Line by calling:

1-800-528-1009

To obtain top performance and assure economical operation, the tractor should be inspected by your

authorized dealer periodically or at least once a year, depending on its hours of use.

CAUTION

DO NOT tow your Model 2164 tractor. Towing may damage the transmission. Place the tractor on a LEVEL SURFACE before pulling the transmission release lever to the disengaged position.

The Cub Cadet hydrostatic drive system requires minimal service if the recommended operation and maintenance procedures are followed.

UNDER NO CIRCUMSTANCES SHOULD YOU ATTEMPT TO SERVICE THESE UNITS YOURSELF. Only your dealer is authorized, under terms of the warranty, to repair or replace drive components of the unit.

When needing parts, always specify the hood model number, factory model number, mfg. date (serial number) and/or the engine spec. and serial numbers (include any prefix and suffix letters). Record these numbers in the space provided on this page.

SERIAL NUMBER LOCATION

NOTE

References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end.

The chassis model plate, showing the factory model number and Mfg. Date (See Figure 1) can be found on the underside of the seat mounting base. Pivot the seat foward to locate the decal.

XXXXXXXXXXX XXXXXXXXXX

Model Number

Mfg. Date

CUB CADET CORP.

P.O. BOX 368023

CLEVELAND, OHIO 44136

The engine serial number decal is located on the right side of engine blower housing (Refer to Figure 2).

 

 

Figure 1

 

 

Figure 2

 

 

 

 

 

 

 

 

 

Hood Model

 

 

Factory Model No.

 

 

 

Mfg. Date

 

 

 

 

 

 

 

 

 

 

 

Delivery Date

 

 

Engine Spec. No.

 

Engine Serial No.

 

 

 

 

 

 

8

SECTION I. CONTROLS AND INDICATORS

Your Cub Cadet Tractor has been safety engineered. This section gives a brief description of the function and location of the various controls and indicators.

Thoroughly acquaint yourself with all the controls and indicators before attempting to start or operate the tractor.

A B

I

C

J

F

D K

E

H G

L

O

M

N

A.

Low Oil Indicator

I.

Brake Pedal

B.

Hour Meter

J.

Forward Control Pedal

C.

Power Take-Off (PTO) Control Switch

K.

Reverse Control Pedal

D.

Ignition/Light Switch

L.

Lift Handle

E.

Throttle Control Lever

M.

Lift Height Indicator

F.

Choke Control

N.

Seat Adjustment Lever

G.

Brake Pedal Lock

O.

Transmission Release Lever

H.

Cruise Control Lever

P.

Fuses (Not Shown)

 

 

Q.

Safety Interlock Switches (Not Shown)

Figure 3

9

A. LOW OIL INDICATOR

This indicator will illuminate when the engine oil level is low. If this indicator illuminates, stop the tractor immediately and check the engine oil level. If the oil level is within the operating range, but the light remains on, contact your Cub Cadet dealer.

CAUTION

Operating the tractor with low oil level or pressure could result in severe engine damage.

B. HOUR METER

The hour meter operates whenever the ignition key is in the “ON” position. Record the actual hours of tractor operation to ensure all maintenance procedures are completed according to the schedule in this manual.

C. POWER TAKE–OFF (PTO) CONTROL SWITCH

The power take-off control switch operates the front electric PTO clutch. Pull the switch knob to engage (“RUN”), or push the knob to disengage (“OFF”) the PTO clutch.

D. IGNITION/LIGHT SWITCH

WARNING

To prevent accidental starting and/or battery discharge, remove the key from the ignition switch when the tractor is not in use.

The combination lights and ignition switch is a four position switch. (See Figure 4)

Figure 4

E. THROTTLE CONTROL LEVER

This lever controls the speed of the engine. When set in a given position, the control cable will maintain a uniform engine speed.

NOTE

When using power take-off operated equipment, best performance is achieved with the throttle lever in the “FAST” position.

This symbol shows slow position.

This symbol shows fast position.

F. CHOKE CONTROL

The choke control is operated manually. Pull the knob out to ckoke the engine; push the knob in to open the choke.

G. BRAKE PEDAL LOCK

WARNING

The hydrostatic transmission will not hold the tractor on a hill. Normal internal leakage in the transmission will allow the tractor to roll downhill. To avoid an accident and/or possible injury, engage the brake pedal lock.

The brake lock lever, located in the center of the dash panel below the steering wheel, is identified with the P symbol. Always engage the brake pedal lock when dismounting the tractor. To engage the brake pedal lock, depress the brake pedal and push down on the brake pedal lock lever. Hold the lever down while releasing the brake pedal. The lever should lock in the down position.

H. CRUISE CONTROL LEVER

The cruise control lever, located in the center of the dash panel below the steering wheel, is identified with the symbol. This lever can be used to maintain a desired “foot free” forward speed in areas where constant speed changes are not required. Refer to Section IIOPERATION for instructions on how to use this feature.

10

I.BRAKE PEDAL

The brake pedal is located at the front of the right running board above the forward control pedal. Press down to stop the tractor and disengage the cruise control. The brake pedal must be fully depressed to activate the safety interlock switch when starting the tractor.

J. FORWARD CONTROL PEDAL

The forward control pedal is located at the front of the right running board below the brake pedal. Slowly press down on the pedal to start moving forward. The forward ground speed of the tractor is directly affected by the distance the pedal is depressed.

K. REVERSE CONTROL PEDAL

WARNING

Check behind the tractor to be sure the area is clear of people, pets or obstacles. Use a slower speed to maintain control of the tractor when traveling in reverse.

The reverse control pedal is located in the right front running board rearward of the the brake and forward control pedals. Press the pedal downward to move in reverse.

L. LIFT HANDLE

The lift handle is located in the left fender and is used to raise and lower equipment used with the tractor. The equipment can be set in any of six positions by depressing the top button on the handle, moving the handle to the desired position, then releasing the button. It may be necessary to push or pull slightly on the handle to depress the button. There is a lift assist spring which reduces the effort needed to lift attachments. To adjust spring tension refer to ADJUSTMENTS in Section III.

M. LIFT HEIGHT INDICATOR

The lift height indicator is located in the left fender and indicates the height of the deck attachment when installed.

N. SEAT ADJUSTMENT LEVER

The seat adjustment lever (see Figure 5) is used to move the seat forward or rearward into one of five positions. See ADJUSTING THE SEAT in Section III.

Figure 5

O. TRANSMISSION RELEASE LEVER

The transmission release lever is located at the back of the tractor in the rear drawbar. This lever disconnects the hydro transmission pump from the rear axle to allow the unit to be pushed a short distance by hand.

To disengage the transmission, pull back on the lever until its locking flange is visible outside the drawbar, then lift the lever up into the slot and release. To re-en- gage the transmission, pull back on the lever, drop out of the slot and release.

P. FUSES

The fuses are located under the hood between the indicator lamps and the hour meter (see Figure 6). Fuses are installed to protect the tractor’s electrical circuitry and components from damage caused by excessive amperage.

Figure 6

11

Q.SAFETY INTERLOCK SWITCHES

This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact your authorized Cub Cadet Dealer. The safety interlock system prevents the engine from cranking or starting unless the brake pedal is fully depressed, and the PTO switch is in the “OFF” position.

The safety interlock system will automatically shut off the engine if the operator leaves the seat before engaging the brake lock.

The safety interlock system will automatically shut off the engine if the operator leaves the seat with the PTO in the “RUN” position, regardless of whether the brake lock is engaged. The PTO switch must be moved to the “OFF” position to restart the engine.

The safety interlock system will automatically shut off the PTO if the reverse control pedal is depressed with the PTO in the “RUN” position. To re-engage the PTO, release the reverse control pedal, move the PTO switch to the “OFF” position, then again pull the switch to the “RUN” position.

FUEL TANK

The fuel tank is located under the rear fender. The filler cap is in the center/rear of the fender (see Figure 7).

Figure 7

HOOD AND SIDE PANELS

The tractor hood is arranged to swing up and forward for easy access to the engine compartment (see Figure 8). Whenever engine maintenance is required, the side panels can be removed.

WARNING

If the engine has been recently run, the engine, muffler and surrounding metal surfaces will be hot and can cause burns to the skin. Allow the tractor to cool and use caution when removing the side panels.

To remove either the right or left side panel, refer to Figure 8 and proceed as follows:

1.Engage the brake lock and raise the hood.

2.Loosen, but do not remove, the rear wing nut and upper front wing nut.

3.Grasp the side panel just behind the grille and pull outward to release the side panel from the tapered bushings on the grille.

4.Slide the side panel forward and out of the groove in the dash panel.

To install either the right or left side panel, refer to Figure 8 and proceed as follows:

1.Slide the rear of panel into the groove in the dash panel.

2.Position the notch of the rear side panel tab on the threads of the bulkhead rod, between the bulkhead and wing nut.

3.Press the slots of the front side panel flange onto the tapered retainers, between the retainers and the grille.

4.Tighten the rear and upper front wing nuts and close the hood.

12

UPPER FRONT

WING NUT

GRASP

REAR WING NUT

SIDE PANEL

REAR TAB

RETAINER WITH

 

 

ON PANEL

 

TAPERED GUIDE

 

 

GRILLE

GROOVE IN

GRASP

DASH PANEL

Figure 8

13

 

SECTION II. OPERATION

WARNING

NOTE

RECEIVE INSTRUCTION - Read the operator’s manual. Learn to operate this machine SAFELY. Don’t risk INJURY or DEATH.

1.Before starting the engine or beginning operation, be familiar with the controls. The operator must be seated, the PTO switch in the “OFF” position and the brake pedal fully depressed.

2.Keep all shields in place. Keep away from moving parts.

3.NO RIDERS! Keep all people and pets a safe distance away. Look behind to both sides before backing up.

4.DO NOT direct the mower discharge at people.

5.Avoid slopes. Tractors can be rolled over.

6.Before leaving the operator’s seat: Shut off the PTO, engage the brake pedal lock, shut off the engine and remove the ignition key. Wait for all movement to stop before servicing or cleaning.

7.Do not fill the fuel tank when the engine is running or while the engine is hot. Tighten the fuel cap securely.

BEFORE OPERATING YOUR TRACTOR

1.Before you operate the tractor, study this manual carefully. It has been prepared to help you operate and maintain your tractor with utmost efficiency.

2.Familiarize yourself with the operations of all the instruments and controls.

3.This engine is certified to operate on unleaded gasoline. Fill the fuel tank with only clean, fresh, unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. Purchase fuel in a quantity that can be used within 30 days to assure fuel freshness.

In countries other than the U.S.A., leaded gasoline may be used if it is commercially available and unleaded is not available.

Some fuels, called oxygenated or reformulated gasolines, are gasoline blended with alcohols or ethers. Excessive amounts of these blends can damage the fuel system or cause performance problems. Do not use gasoline which contains Methanol. If any undesirable operating symptoms occur, use gasoline with a lower percentage of alcohol or ether.

4.Check the engine and transmission oil levels.

5.Clean the air cleaner element if necessary.

6.Check the tire inflation pressures.

7.Adjust the seat for operator’s maximum comfort, visibility and for maintaining complete control of the tractor.

8.Remove the side panels and clean any accumulated grass and debris from the engine air inlet screen. Also clean the dash air intake screen, grille and side panels to ensure adequate cooling.

9.Refer to the various sections of the Operator’s Manual for additional information.

STARTING THE ENGINE

WARNING

For personal safety, the operator must be sitting in the tractor seat when starting the engine.

WARNING

This unit is equipped with a safety inerlock system designed for the protection of the operator. Do not operate the tractor if any part of the interlock system is malfunctioning. Periodically check the functions of the interlock system for proper operation as described below:

The safety interlock system prevents the engine from cranking or starting unless the brake pedal is fully depressed and the PTO clutch engagement switch is in the “OFF” position.

14

The safety interlock system will automatically shut off the engine if the operator leaves the seat before engaging the brake pedal lock.

The safety interlock system will automatically disengage the PTO if the reverse control pedal is pressed down with the PTO in the “RUN” position. To re-engage the PTO, release the reverse control pedal, move the PTO switch into the “OFF” position and then engage the PTO while seated.

The safety interlock system will automatically shut off the tractor engine if the operator leaves the seat with the PTO in the “RUN” position.

1.Operator must be sitting in the tractor seat.

2.Pull choke control knob to full choke position. Less choking may be necessary due to variations in temperature, grade of fuel, etc. Little or no choking will be needed when the engine is warm.

3.Place the throttle midway between the “SLOW” and “FAST” position.

4.Place the PTO switch in the “OFF” position.

5.Fully depress the brake pedal.

6.Turn the ignition key clockwise to the “START” position and release it as soon as the engine starts; however, do not crank the engine continuously for more than 10 seconds at a time. If the engine does not start within this time, turn the key “OFF” and wait a minute to allow the engine’s starter motor to cool, then try again.

7.After the engine starts, slowly release the brake pedal. As the engine warms up, gradually push the choke control knob all the way in. Do not use the choke to enrich the fuel mixture, except as necessary to start the engine.

NOTE

This engine is designed to give maximum performance and service life if operated with the choke fully open and the throttle in the “FAST” position. To open the choke fully requires an engine warmup period of several seconds to several minutes, depending on the outdoor temperature.

After starting the engine, push in the choke control until the engine begins to run smoothly. As the engine warms and begins to run roughly, continue to push in the choke control as necessary to keep the engine running smoothly until the choke is fully depressed. Operating equipment during engine warmup is not recommended.

STOPPING THE ENGINE

CAUTION

Remove the key from the ignition switch to prevent accidental starting or battery discharge if the equipment is left unattended.

Place the PTO switch in the “OFF” position. Move the throttle control lever midway between the “SLOW” and “FAST” positions. Wait a moment to allow the engine speed to stabilize, then turn the ignition key to the “OFF” position. Remove the key from the ignition switch.

TRACTOR BREAK-IN PROCEDURE

CAUTION

Never operate a new engine immediately under full load. Break it in carefully as shown in the table below.

15

COLD WEATHER STARTING

WARNING

Engine exhaust gases are dangerous. Do not run the engine in a confined area such as a storage building any longer than is necessary. Immediately move the tractor outdoors.

WARNING

For personal safety, the operator must be sitting in the tractor seat before starting the tractor.

When starting the engine at temperatures near or below freezing, ensure the correct viscosity motor oil is used in the engine and the battery is fully charged. Start the engine as follows:

1.Pull the choke all the way out to full choke position.

2.Move the throttle control lever to midway between the “SLOW” and “FAST” position.

3.Place the PTO switch in the “OFF” position.

4.Fully depress the brake pedal.

5.Turn the ingnition key to the “START” position and hold until the engine starts; however, do not crank the engine continuously for more than 10 seconds at a time. Once the engine starts, gradually adjust the choke as needed to keep the engine running until warmed up, then push the choke control all the way in.

NOTE

If the engine fails to start after several attempts, the engine may become flooded. If this happens, wait a minute to allow the starter motor to cool. Move the throttle control to the “SLOW” position, push the choke in all the way and momentarily crank the engine to help clear the cylinders. With the throttle control in the “SLOW” position and the choke all the way in, turn the ignition key to the “START” position while slowly pulling the choke out to a position that will allow the engine to start. Gradually adjust the choke as needed to keep the engine running until warmed up, then push the choke control all the way in.

DRIVING THE TRACTOR

CAUTION

Avoid sudden starts, excessive speed and sudden stops.

CAUTION

Do not leave the seat of the tractor without disengaging the PTO, depressing the brake pedal and engaging the brake pedal lock. If leaving the tractor unattended, also turn the ignition key off and remove the key.

NOTE

When using power take-off operated equipment, best performance is achieved with the throttle lever in the “FAST” position.

1.Depress the brake pedal to release the brake pedal lock and let the pedal up. Move the throttle lever to the position where the engine operates best for the load to be handled.

2.Driving with forward or reverse pedals.

CAUTION

Do not use the forward or reverse control pedals to change the direction of travel when the tractor is in motion. Use the brake pedal to bring the tractor to a stop before depressing either the forward or reverse control pedal.

a.To move forward, slowly depress the forward control pedal until the desired speed is achieved.

b.To move in reverse, check that the area behind is clear then fully depress the reverse control pedal.

3.Using the cruise control lever.

NOTE

The cruise control feature can only be operated in the forward direction.

16

a.Slowly depress the forward control pedal until the desired speed is achieved.

b.Lightly push the cruise control lever downward as far as possible and hold in this position.

c.While continuing to hold the cruise lever down, lift your foot from the forward control pedal (you should feel the cruise latch engage).

d.If properly engaged, the cruise lever and forward control pedal should lock in the down position, and the tractor will maintain the same forward speed.

e.Disengage the cruise control using one of the following methods:

Depress the brake pedal to disengage the cruise control and stop the tractor.

Lightly depress the forward control pedal.

Lift the cruise control lever upward.

NOTE

Although not recommended, depressing the reverse pedal will also disengage the cruise control.

f.To change to the reverse direction when operating with cruise control, depress the brake pedal to disengage the cruise control and stop the tractor; then depress the reverse control pedal.

DRIVING ON SLOPES

Refer to the SLOPE GAUGE on page 57 to help determine slopes where you may not operate safely.

WARNING

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). The tractor could overturn and cause serious injury.

WARNING

Operate the tractor up and down slopes, never across slopes. Always drive up or down the face of a slope. Do not drive so that the tractor may tip over sideways .

Before operating the tractor on any slope, walk the slope to look for possible hazards such as rocks. mounds, ruts, stumps or other surface irregularities which could cause the tractor to be upset.

Back the tractor with implement up the steepest portion of each slope you intend to work. If the tractor cannot negotiate the slope in reverse, the slope is too steep to be worked.

Avoid turns when driving on a slope. If a turn must be made, turn down the slope. Turning up a slope greatly increases the chance of a roll over.

Avoid stopping when driving up a slope. If it is necessary to stop while driving up a slope, start up smoothly and carefully to reduce the possibility of flipping the tractor over backward.

STOPPING THE TRACTOR

CAUTION

Always engage the brake pedal lock, push the PTO switch to the “OFF” position, lower the equipment and shut off the engine before dismounting. Never try to start the engine while standing on the ground.

Fully depress the brake pedal to bring the tractor to a complete stop (and disengage the cruise control), engage the brake pedal lock, disengage the PTO, turn the ignition switch to “OFF’” and remove the key from the switch before dismounting.

OPERATING THE POWER TAKE-OFF (PTO) CLUTCH

Before operating the new clutch under load (mowing grass, etc.), perform the following break-in procedure:

1.Start and run the engine a few minutes to warm up.

2.With the mowing deck, snow thrower, etc. installed and the engine running at approximately 50% throttle, engage and disengage the clutch at ten second intervals (ten seconds ON-ten seconds OFF) five times. The engine choke may have to be pulled out slightly to accomplish this.

3.Increase the engine speed to 75% throttle and again engage and disengage the PTO clutch at ten second intervals five times.

4.Make certain the PTO is disengaged and stop the engine.

17

Operate the PTO clutch as follows:

1.Move the throttle control lever to approximately the mid throttle position.

2.Pull the PTO switch to the “RUN” position.

3.Advance the throttle lever to the operating speed (full engine speed).

4.The operator must remain in the tractor seat at all times. If the operator should leave the seat without turning off the power take-off switch, the tractor’s engine will shut off.

5.The PTO clutch cannot be operated when the tractor is driving in the reverse direction. The PTO switch must in the “OFF” position when the reverse control pedal is depressed, or the PTO clutch will automatically disengage. To re-engage the PTO clutch, release the reverse control pedal, move the PTO switch to the “OFF” position, then again pull the switch to the “RUN” position.

DRAWBAR

Drawbar type equipment must be hitched to the tractor only at the hitch hole in the drawbar (See Figure 9).

Figure 9

18

Loading...
+ 42 hidden pages