GX-10
GUITAR AMPLIFIER
OWNER’S MANUAL
Congratulations!
You are now the proud owner of the compact Crate GX-10 Guitar Amplifier. The GX-10 features built-in overdrive circuitry, three bands of equalization, an insert jack and a jack for headphones.
In order to get the most out of your new amplifier, we strongly urge you to go over the information contained in this manual before you begin playing.
And thank you for choosing 
GX-10 Guitar Amplifier
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO. NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
IMPORTANT SAFETY INSTRUCTIONS
•READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
•DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS.
•DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
•CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
•ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
•PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
•UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
•ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR SAFE OPERATION AND TO AVOID INJURY.
•THIS APPARATUS DOES NOT OPERATE NORMALLY AND REQUIRES SERVICE WITH ANY PHYSICAL DAMAGE FROM IMPACT OR ANY EXPOSURE TO MOISTURE.
•SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
•OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
EXPLANATION OF GRAPHICAL SYMBOLS: |
"DANGEROUS VOLTAGE" |
EXPLICACION DE SIMBOLOS GRAFICOS: |
= “VOLTAJE PELIGROSO” |
EXPLICATION DES SYMBÔLES GRAPHIQUES: |
"DANGER HAUTE TENSION" |
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
=“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION"
Getting Your Sound: The Overdrive Level and Gain and the Clean Level controls (#2, 3 & 4) can be used together to obtain a wide variety of sounds. The following guidelines will help you get the sound you’re looking for.
Clean Sounds: Keep the Gain control “off” (the Overdrive Level control will be inactive). Use the Clean Level control to set the output level.
“Crunch” Sounds: Set the Overdrive Level control around “4”, turn the Gain on and set it to “2”. Use the Clean Level control to set the output level. (A lower setting of the Clean Level control is needed as the Overdrive Level and Gain controls are increased.)
Rhythm Distortion: Set the Overdrive Level control around “4”, Gain at or near “10”. Use the Clean Level control to set the output level.
Lead Distortion: Set the Overdrive Level and Gain controls at or near “10”. Use the Clean Level control to set the output level.
Connecting to the Insert jack: The Insert jack (#8) lets you patch external effects into the amplifier prior to its power amp stage. Use Crate’s STP201, STP202 or STP203 stereo-to-mono Y-cord or an adapter such as Crate’s YPP117 and 2 1/4” mono signal cables to connect to the effect as shown:
Stereo-to-mono Y-cord: |
Y-adapter and 2 cables: |
||||
to Insert |
TIP |
|
RETURN |
TIP |
to Insert |
jack |
RING |
|
SEND |
RING |
jack |
|
SLEEVE |
|
GROUND |
SLEEVE |
|
(STP201, 3' |
|
|
|
(YPP117) |
|
STP202, 6' |
|
|
|
|
|
STP203, 9') |
|
|
|
|
|
|
|
|
|
T |
I R |
|
|
|
|
P I |
G N |
T |
|
I R |
|
|
|
P I |
|
G N |
|
|
|
|
|
|
|
(1/4"-TO-1/4" |
|
|
|
|
|
MONO CABLES) |
|
to |
to |
|
|
to |
to |
effect |
effect |
|
|
effect |
effect |
"OUT" |
"IN" |
|
|
"OUT" |
"IN" |
jack |
jack |
|
|
jack |
jack |
External Effect |
|
|
External Effect |
||
Loading...