CMS188
FRANÇAIS
ESPAÑOL
ENGLISH
MS188, CMS188
MS188W, CMS188W
Instruction Manual
Instrucciones
Directives
Congratulations. You have purchased a Regent motion activated floodlight. This
security lighting system will provide years of convenience and protection for your
home and family.
How it works
Your Regent motion activated floodlight senses heat
images from objects such as people, large animals and
automobile engines. When motion is detected, the light
will automatically turn on. Once motion has stopped, the
light will turn off after a preselected time delay. Your
motion activated floodlight may also be used as a stan-
dard floodlight.
What you need
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
What’s included
• Motion detector and light fixture (A)
• 300 watt quartz halogen bulb (B)
• Coverplate gasket (C)
• (4) Coverplate screws (D)
• (3) Wire nuts (E)
What to know
• For outdoor use only.
• UL and CUL LISTED for wet locations.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Under Part 15 of the FCC Rules, any changes or
modifications to the motion detector described in this instruction sheet that are not
expressly approved by Cooper Lighting could void the user’s authority to operate
the equipment. NOTE:This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Fixture must be connected to a 120 Volt, 60 Hz, 2.5, 300 watt power source. Any
2
ENGLISH
MS188, CMS188 (Bronze)
MS188W, CMS188W (White)
70 foot
range
180 degrees
A
B
CDE
other connection voids warranty.
• Fixture should be mounted to a grounded junction box marked for use in
wet locations.
• Do not allow sensor head to touch light housing – maintain at least 1” space
between fixture and sensor.
• Keep away from flammable objects. Do not mount body of fixture
within one inch of any combustible material.
• The bulb and fixture get extremely hot during use.
• Use only with a 300 watt or smaller bulb. Installing a bulb of a higher wattage
could create a fire hazard. Use of a higher wattage bulb will void the warranty.
• Never touch the bulb with your bare hands. Handle the bulb with gloves or a soft
cloth. Oil from your skin can cause premature bulb failure.
• For maximum bulb life, position fixture so the quar tz halogen bulb remains
within 4 degrees of horizontal.
• If lens is replaced, use only tempered safety glass of equal thickness.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electr ically connect-
ing the fixture to it, must be in accordance with the National Electrical Code and
local building codes.
• For supply connections use wire rated at least 75 degrees C.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• Disassembly of your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
For best results
• Install your fixture 8-12 feet above ground (motion detector
is less sensitive above 12 feet).
• Locate fixture so motion moves across detection zone (F).
• Locate fixture away from heat producing sources to prevent
false triggering. Also be very careful not to include objects
such as windows, white walls and water in the detection
zone whenever possible.
• Locate fixture away from moving objects such as trees and street traffic.
• Do not install more than one motion activated floodlight on
one wall switch.
Installing the bulb
Step 1: Remove screws from the front of the lens frame.
Step 2: Using gloves or a soft cloth, gently insert bulb by
pressing one end into the spring loaded socket and
repeat with the opposite end. Bulb should fit
securely into contacts (G).
Step 3: Secure lens frame onto fixture with screws.
Mounting your fixture
Turn off the power at the main fuse/breaker box.
Check to make sure power has been disconnected
before continuing.
Step 1: Thread fixture wires through coverplate
gasket (H and I).
Step 2: Attach ground wire from the fixture to ground
wire coming from your house. If no ground
wire is available, attach fixture ground wire to
ENGLISH
3
F
G
Your fixture mounts
to the following standard
junction boxes:
Round OctagonalRectangular
(horizontal)
the junction box.
Step 3: Connect black wire to house black wire and con-
nect white wire to house white wire using wire nuts
provided.
Step 4: Attach fixture to the junction box with two screws
provided.
W
all Mount
Match up screws on the floodlight coverplate with
the junction box screw holes. (If necessary, lightly tap selected cover plate
holes with a hammer and screwdriver to open them.)
Attach fixture to junction box.
Ea
ve Mount
Loosen screw which connects sensor arm to coverplate
arm (I). Rotate coverplate arm upwards, allowing stop on
coverplate arm to clear stop on sensor arm. NOTE: Once
stop on coverplate arm is above (to the left of) stop on
sensor arm, tighten screw. Be careful not to break stops.
Step 5: Apply silicone caulking around the edges of coverplate
and in any open screw holes for a water tight seal.
Step 6: Turn power on at main fuse/breaker box.Ho
How to operate your fixtrue
Step 1: Move slide switch on bottom of the sensor to “TEST”. Set sensitivity knob
to medium (halfway) (J).
Step 2: Turn on the power to fixture. Allow fixture to warm up
approximately 40 seconds before testing. (Light will
come on and stay on during warm-up period.)
Step 3: Aim sensor head toward desired detection area, main-
taining a 15° down angle to allow moisture to
drain. NOTE: Maintain air spacing between lamp
and sensor head, at least 1”. Make sure sensor
head is positioned with control switches facing
towards the ground.
Step 4: Walk across the detection zone at the farthest dis-
tance you wish your detector to detect motion.
Step 5: Adjust sensitivity until you get desired results.
Light will turn off 4 seconds after all motion stops.
Step 6: Move the slide switch to 4 MIN or 12 MIN (AUTO mode). At dusk, lights
will operate in the AUTO setting.
4
ENGLISH
H
(wall mount)
I
(eave mount)
THIS IS THE
BOTTOM SIDE
OF THE MOTION
DETECTOR
J
TEST
4 MIN
12 MIN
SENSITIVITY
How to select your desired feature
ENGLISH
5
Auto Setting
(motion activated)
Light should turn on with
motion only at night and
should turn off after
4 or 12 minutes.
4 MIN
or
12 MIN
Keep the power to
the fixture on.
Dusk to Dawn Setting
(activated only at night)
Light should stay on from
dusk to dawn and then reset
to the auto setting next
dawn.
4 MIN
or
12 MIN
Turn power on and off twice
within 3 seconds
Standard Floodlight
Setting
Light should stay on continu-
ously both day and night
(must be reset manually).
TEST Turn power on and off twice
within 3 seconds
Test Setting
Light should turn on with
motion both day and night.
Light should turn off after
4 seconds.
TEST Keep the power to the
fixture on.
Return to Auto Setting
(motion activated)
From any of the above
settings.
4 MIN
or
12 MIN
Turn the power “OFF” for at
least 40 seconds, then
back “ON”.
Mode of
operation:
Set slide switch
on sensor to:
How to set
power switch:
What to do if . . .
Five year limited warranty
Cooper Lighting (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of five years from date of original
purchase, and agrees to repair or, at the Company’s option, replace a defective
6
ENGLISH
OUTDOOR LIGHT DOES
NOT COME ON WITH
MOTION AT NIGHT
OUTDOOR LIGHT
COMES ON FOR NO
APPARENT REASON AT
NIGHT
LIGHT STAYS ON AT
NIGHT AND DOES NOT
TURN OFF
LIGHT CONTINUOUSLY
BLINKS ON AND OFF AT
NIGHT
LIGHT IS ON DURING
THE DAY
CANNOT ACTIVATE
DUSK TO DAWN MODE
AT NIGHT (OVERRIDE)
Is there power to the fixture?
• Check to see that the circuit breaker has not been tripped.
• Be sure the wall switch is in the “ON”position.
• Be sure that the bulb is not burned out or broken.
Is the surrounding external ambient light too bright? (If so the
unit may think it’s daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING.
Is the wiring to the fixture loose?
• Check wiring, and reconnect if necessary using wire nuts
provided.
Is there motion in the detection zone?
• Make sure the sensor is not picking up moving objects such
as trees, traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard to prevent sensor
from detecting motion. If the light stays off, something in
the detection zone is triggering the sensor.
• If this is the case, reduce the sensitivity.
• Reposition motion sensor.
*If the light stays on with sensor lens covered, contact
customer service.
Is there motion in the detection zone?
• Make sure the sensor is not picking up moving objects such
as trees, traffic, etc.
• If this is the case, reduce the sensitivity.
• Reposition motion sensor.
If there is no motion, then the unit may be in the override mode.
• Turn the light switch to the “OFF” position for 40 seconds,
and then back to the “ON” position. This will send the unit
back into the AUTO mode.
*If the light continues to stay on, contact customer service.
The light given off from the unit’s own lamp is affecting the
motion sensor.
• Re-aim lamp.
• Reposition motion sensor.
Is the switch on the bottom of the motion sensor in the test
mode?
• Move the switch to the AUTO 4 or 12 position.
Is the motion detector shadowed?
• Reposition motion sensor.
Is the surrounding external ambient light too bright? (If so the
unit may think it’s daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
Are you allowing adequate time to enter the dusk to dawn
mode?
• Turn power on and off twice within 3 seconds
Is there more than one fixture on an indoor wall switch?
• If so, put them on separate switches.
Loading...