STITCH LINE
OASISTM CABIN TENT MODEL 2000000583
Before you begin
Read all instructions before set up.
•Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
•Do not set up your tent under trees.
•For best results in windy conditions, position end of tent into the wind.
•Enlist the help of at least one other person to assist you when it is time to assemble the tent.
Parts and Components
Description |
Part Number |
|
Hub (1) |
5010000120 |
|
Short Ridge Pole (2) |
5010000121 |
|
Long Leg Pole (2) |
5010000122 |
|
Short Leg Pole (4) |
5010000123 |
|
Long Ridge Pole (4) |
5010000124 |
|
Awning Pole (2) |
5010000125 |
|
Rainfly (1) |
5010000126 |
|
|
|
|
Short Ridge Poles (2) |
Hub (1) |
|
Long Leg Poles (2) |
||
|
||
Short Leg |
|
|
Poles (4) |
|
|
Long Ridge |
|
|
Poles (4) |
|
|
Awning Poles (2) |
|
To Set Up Tent
1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1
Doors
2. Insert the two Short Ridge Poles (with sticker dots) into the sleeves (perpendicular to door) on top of tent. (Fig. 2)
3. Assemble four, shockcorded, Long Ridge Poles and insert into the four diagonal corner sleeves. (Fig. 2)
Fig. 2
4. Insert end of first Short Ridge Pole (with |
Hub |
Short Ridge |
dot) into flange with a dot on Hub (Fig. 3). |
|
Pole with |
|
Dot |
|
Repeat for remaining Short Ridge Pole on |
|
|
opposite flange of Hub with a dot. |
|
|
NOTE: When installed properly, the loop on |
|
|
the bottom of the Hub will be parallel |
|
|
Fig. 3 |
|
|
two Short Ridge Poles. |
|
|
|
|
5. Insert four remaining Long Ridge Poles into Hub. (Fig. 4)
|
|
|
|
NOTE: Make sure tab on each |
||||||||
|
|
|
|
pole locks into slot on bottom |
||||||||
|
|
|
|
of Hub. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hub |
|
|
|
|
|
|
|
|
|
|
(Fig. 5) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tab |
|
|
|
|
|
|
|
|
|
|
|
|
|
Locked |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tab |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Slot |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 4 |
|
|
Tab on |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 5 |
||||
|
|
|
|
|
|
Pole |
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
6.Snap hook at top of tent onto metal loop on bottom of Hub. (Fig. 6)
Fig. 6
7.Insert curved end of four Short Leg Poles into the four Long Ridge Poles on top of tent. (Fig. 7)
NOTE: Make sure tab on each Long Ridge Pole locks into slot on each Short Leg Pole.
Fig. 7
8.Insert curved end of two Long Leg Poles (with dots) into the Short Ridge Poles at front & back of tent. (Fig. 8)
NOTE: Make sure tab on each Short Ridge Pole locks into slot on each Long Leg Pole.
|
Long Leg Pole (with Dots) |
Short Leg Poles |
Short Leg Poles |
|
(Front of Tent)
Long Leg Pole
(with Dots)
Fig. 8
9. Raise tent by assembling shock-corded sections of each Long and Short Leg Pole and inserting into curved ends of Leg Poles. (Fig. 9) Fig. 9 Fig. 10
10. Insert pin on loop at each corner and the front and back of tent into all six Leg Poles. (Fig. 10)
11.Locate both plastic hooks at each corner, and front and back of tent, then snap onto Leg Poles to attach. (Fig. 11)
12. Drive stakes through rings, located on |
|
|
|
|
|
|
|
Fig. 12 |
|
|
|
four corners and front and back of tent, |
|
|
|
|
|
|
|
at an angle for better anchoring. |
|
|
|
(Fig. 12) |
|
|
|
|
|
|
|
|
|
|
|
To Attach Rainfly
1.Drape Rainfly over tent. Make sure seams on Rainfly are facing down with web pockets and long straps centered over doors
& back of tent. (Fig. 13)
Rainfly
Long Strap
Fig. 13
2. Locate and wrap hook and |
|
Hook and Loop |
|
loop fasteners, on underside of |
|
Fastener |
|
|
|
||
Rainfly, and wrap around the |
|
|
|
Leg Poles to secure. (Fig. 14) |
|
|
|
|
|
|
Fig. 14 |
|
|
|
|
(continued on other side) |
|
|