Loading...
Owner’s manual / Mode d’emploi Bedienungsanleitung / Istruzioni per l’uso Gebruiksaanwijzing / Manual de instrucciones Bruksanvisning / Manual de instruções
DB248R/DB248RB
DB148R/BD149R
BD149RG
RDS-EON/FM/MW/LW RADIO CD COMBINATION
•
COMBINE RADIO FM/PO/GO RDS-EON-LECTEUR DE CD
•
RDS-EON UKW/MW/LW RADIO-CD-KOMBINATION
•
COMBINAZIONE DI RADIO RDS-EON FM/MW/LW E LETTORE CD
•
RDS-EON FM/MW/LW RADIO CD COMBINATIE
•
COMBINACIÓN DE RADIO RDS-EON DE FM/MW/LW Y REPRODUCTOR DE CD
•
KOMBINERAD FM/MV/LV-RADIO MED RDS-EON OCH CDSPELARE
•
COMBINAÇÃO DE CD COM RÁDIO FM/MW/LW RDS-EON
Thank you for purchasing this Clarion product.
Please read this owner’s manual in its entirety before operating this equipment.
After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
Check the contents of the enclosed warranty card and keep it carefully with this manual.
CAUTIONS:
This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT”. To use this model properly, read this Owner’s Manual carefully and keep this manual for your future reference. In case of any trouble with this player, please contact your nearest “AUTHORIZED service station”. To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS!
Apparaten innehåller laserkomponenten som avger laserstrålning överstigande gränsen för laserklass 1.
VAROITUS
Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähettää näkymätöntä silmille vaarallista lasersäteilyä.
!CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
ADVARSEL.
Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hvilket betyder, at der anvendes laserstråler af svageste klasse, og at man ikke på apparatets yderside kan blive udsat for utilladelig kraftig stråling.
APPARATET BØR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsaætte sig for laserstråling.
2 DB248R/DB148R/BD149RG
English |
4. DCP |
theft. When detaching the control panel, store it |
|
|
The control panel can be detached to prevent |
|
in the DCP (DETACHABLE CONTROL PANEL) |
|
case to prevent scratches. |
|
We recommend taking the DCP with you when |
|
leaving the car. |
Removing the DCP
1.Press the [FNC] button for 1 second or longer to switch off the power.
2.Press in the [RELEASE] button.
[RELEASE] button
The DCP is unlocked
3.Remove the DCP.
DCP
Attaching the DCP
1.Insert the right side of the DCP into the main unit.
2.Insert the left side of the DCP into the main unit.
2.
DCP
1.
Storing the DCP in the DCP Case
Hold the DCP, in the orientation as shown in the figure below, and put it into the supplied DCP case. (Ensure the DCP is in the correct orientation.)
DCP 
DCP case 
CAUTION
•The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks.
•When the Release button is pressed and the DCP is unlocked, the car’s vibrations may cause it to fall. To prevent damage to the DCP, always store it in its case after detaching it. (ee figure below.)
•The connector connecting the main unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc.
DCP Rear Panel |
Main Unit Front |
DCP connector
Main unit connector
Note:
•If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.
Contents |
|
|
1. |
PRECAUTIONS ............................................................................................................................... |
3 |
|
Handling Compact Discs ................................................................................................................. |
4 |
2. |
CONTROLS ..................................................................................................................................... |
5 |
3. |
NOMENCLATURE .......................................................................................................................... |
6 |
|
Names of the Buttons and their Functions ...................................................................................... |
6 |
|
Display Items ................................................................................................................................... |
7 |
|
LCD Screen ..................................................................................................................................... |
7 |
4. |
DCP ................................................................................................................................................. |
8 |
5. |
OPERATIONS ................................................................................................................................. |
9 |
|
Basic Operations ............................................................................................................................. |
9 |
|
Radio Operations ........................................................................................................................... |
11 |
|
RDS Operations ............................................................................................................................. |
13 |
|
CD Operations ............................................................................................................................... |
16 |
6. |
IN CASE OF DIFFICULTY ............................................................................................................ |
17 |
7. |
ERROR DISPLAYS ....................................................................................................................... |
18 |
8. |
SPECIFICATIONS ......................................................................................................................... |
18 |
1.PRECAUTIONS
1.This unit is applicable for on-road 4 wheel vehicle purpose only. Use for tractor, fork truck, bulldozer, off road vehicle, 2 or 3 wheel motor bicycle, marine boat or other special purpose vehicle is not appropriate.
2.When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour. The condensation will disappear naturally allowing normal operation.
3.Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip.
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY.
For VW and Audi Vehicles
1.When the car stereo is installed in 1998 and later Volkswagen models, make sure to cut the car lead wire connected the A-5 terminal.
(A breakdown could occur if the lead wire is not cut.) After cutting the lead wire, insulate the front end of the lead wire with insulation tape to prevent the risk of short-circuits.
Note:
Before cutting the lead wire, disconnect the car battery - (negative) cable.
2.When the main unit is also connected to an external amplifier, connect REMOTE on the external amplifier to the previously cut lead wire on the side of the connector.
3.Volkswagen models have already changed position of the fuse for installation in such vehicles.
English
Handling Compact Discs
Use only compact discs bearing the
mark.
Do not play heart-shaped, octagonal, or other specially shaped compact discs.
Handling
•Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played.
Therefore, do not leave them for a long time in the car.
•New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc.
Storage
•Do not expose compact discs to direct sunlight or any heat source.
•Do not expose compact discs to excess humidity or dust.
•Do not expose compact discs to direct heat from heaters.
Cleaning
•To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference.
•Do not use any solvents, such as commercially available cleaners, anti-static spray, or thinner to clean compact discs.
•After using special compact disc cleaner, let the compact disc dry off well before playing it.
Ball-point pen
Roughness
•Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen.
•Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player.
•Do not use compact discs that have large scratches, are misshapen, cracked, etc. Use of such discs may cause misoperation or damage.
•To remove a compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges.
•Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may damage the disc or cause breakdown of the internal mechanism.
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante. Bitte ausbreiten und die nächste Seite lesen. / Assicurarsi di aprire e leggere la pagina successiva.
Volgende pagina uitvouwen en doorlezen a.u.b. / Cerciórese de desplegar y de leer la página siguiente. Glöm inte att vika ut och läsa nästa sida. / Não deixe de abrir e ler a próxima página.
English
8 |
DB248R/DB148R/BD149RG |
DB248R/DB148R/BD149RG |
3 |
DB248R/DB148R/BD149RG |
4 |
English
Français
Deutsch
Italiano
Nederlands
Español
Svenska
tuguêsrPo
2. CONTROLS / LES COMMANDES / REGLER / CONTROLLI
REGELAARS / CONTROLES / KONTROLLER / CONTROLOS
Main unit / Appareil principal / Hauptgerät / Apparecchio principale Hoofdtoestel / Unidad principal / Huvudenhet / Unidade principal
[CD SLOT] |
[RPT] |
|
|
|
[DIRECT] |
||
|
[SCN] |
||
[RELEASE] |
[Q] |
||
|
|||
[PTY] |
[RDM] |
|
|
[FNC] |
|
|
[A-M] 
[BND]
[AF] |
[Z] |
[TA] |
[P/A] |
[a],[d] |
[s] |
[DISP] |
|
||
[ROTARY] |
[SS] |
|
|
|
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapitel die Frontdiagramme beachten.
Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo.
Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken. Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
Observera: Vik ut denna sida för att kunna se figurerna över bilstereons framsida medan du läser de olika kapitlen. Nota: Certifique-se de abrir esta página e consulte os diagramas frontais conforme realiza a leitura de cada capítulo.
English
3. NOMENCLATURE
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “2. CONTROLS” on page 5 (unfold).
Names of the Buttons and their Functions
[FNC] button
•Press the button to turn on the power.
Press and hold the button for 1second or longer to turn off the power.
•Switches the operation mode among the radio mode, etc.
[RELEASE] button
•Press the [RELEASE] button to unlock the
DCP.
[PTY] button
•Use the button to set the PTY (Programme Type) standby mode or PTY items.
[CD SLOT]
• CD insertion slot.
[RDM] button
• Performs random play while in the CD mode.
[SCN] button
•Performs scan play for 10 seconds for each track while in the CD mode.
[RPT] button
• Plays repeatedly while in the CD mode.
[DIRECT] button
•Stores a station into memory or recall it directly while in the radio mode.
[Q] button
• Ejects a CD when it is loaded into the unit.
[AF] button
•Press the button to turn on or off the AF (Alternative Frequency) function.
•When the button is pressed and held, Regional function can select ON or OFF.
[Z] button
•Use the button to select one of the three types of sound characteristics already stored in memory. (Z-Enhancer)
[TA] button
•Use the button to set the TA (Traffic Announcement) standby mode.
[P/A] button
•Performs preset scan while in the radio mode. When the button is pressed and held, auto store is performed.
[DISP] button
•Press the [DISP] button while keeping the
[BND] button pressed, to switch the display indication (Main display, clock display).
[SS] button
•Press the [SS] button while keeping the
[BND] button pressed, to turn the screen saver function on or off.
[s] button
• Plays or pauses a CD while in the CD mode.
[a], [d] button
•Selects a station while in the radio mode or selects a track when listening to a CD.
•Press and hold the button for 1 second or longer to switches the fast-forward/fast-back- ward.
[ROTARY] knob
•Adjust the volume by turning the knob clockwise or counterclockwise.
•Use the knob to perform various settings.
[BND] button
•Switches the band, or seek tuning or manual tuning while in the radio mode.
•Plays a first track while in the CD mode.
[A-M] button
•Press and hold the button for 1 second or longer to switch the MAGNA BASS EXTEND on/off.
•Use the button to switch to the audio mode (bass/treble, balance/fader)
Display Items
PS names, PTYs, CT (clock), etc. are displays. |
English |
Operation status indication |
|
|
Z-enhancer indication |
: M-B EX (MAGNA BASS EXTEND) indication
: Scan indication
: Repeat indication 
: Random indication
: Preset channel indication (1 to 6)
: Manual indication
: Alternative frequency indication
: Regional indication
: Traffic announcement indication
: Traffic programme indication 
: Programme type indication
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
5 |
DB248R/DB148R/BD149RG |
6 |
DB248R/DB148R/BD149RG |
DB248R/DB148R/BD149RG |
7 |
5. OPERATIONS
Basic Operations |
Note:Be sure to read this chapter referring to the front diagrams of |
chapter “2. CONTROLS” on page 5 (unfold). |
CAUTION
Be sure to lower the volume before switching off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit.
Audio Mode Adjustments
Press the [A-M] button to select the adjustment mode. The mode switches as follows each time the [A-M] button is pressed:
BASS TREB BAL FAD Previous mode
When the Z-Enhancer function is turned on, BASS (bass) and TRE (treble) cannot be selected.
Turning on/off the power
Note:
•Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery.
1.Press the [FNC] button.
2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.
3.Press and hold the [FNC] button for 1 second or longer to turn off the power for the unit.
Selecting a mode
1.Press the [FNC] button to change the operation mode.
2.Each time you press the [FNC] button, the operation mode changes in the following order:
Radio mode CD mode Radio mode...
Note:
•If the CD mode is selected when no disc is inserted, the display shows “NO DISC”.
Adjusting the volume
Turning the [ROTARY] knob clockwise increases the volume; turning it counterclockwise decreases the volume.
The volume level is from 0 (minimum) to 33 (maximum).
Switching display
Press and hold the [BND] button, and then press the [DISP] button to select the desired display.
The display switches in the following order:
Main Clock (CT) Main …
If the display is changed by other button operation when the clock (CT) is displayed, the clock display returns automatically after the operation.
The example shows the display in radio mode.
Main display
Clock(CT) display
Main display
Setting the Z-nhancer
This unit are provided with 3 types of sound tone effects stored in memory. Select the one you prefer.
The factory default setting is “Z-EHCR OFF”.
Each time you press the [Z] button, the tone effect changes in the following order:
“Z-ENHANCER 1” “Z-ENHANCER 2” “Z- ENHANCER 3” “Z-EHCR OFF” “Z- ENHANCER 1”...
•Z-ENHANCER 1 : bass emphasized
•Z-ENHANCER 2 : treble emphasized
•Z-ENHANCER 3 : bass and treble empha-
sized
• Z-EHCR OFF : no sound effect
English
DB248R/DB148R/BD149RG 9
Loading...