Cisco Systems XR 12000 User Manual

Size:
709.33 Kb
Download

C H A P T E R 3

Getting Started

This chapter describes the typical tasks you should complete to start using the Cisco 12000/10720 Router Manager application. See Figure 3-1 on page 3-2 for further details.

This chapter provides the following information:

Cisco 12000/10720 Router Manager Workflow

Starting Cisco EMF and Cisco 12000/10720 Router Manager

Deployment

Cisco 12000/10720 Router Manager Workflow

Figure 3-1 outlines the steps involved in installing, configuring and using the Cisco 12000/10720 Router Manager application.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-1

 

 

 

Chapter 3 Getting Started

Cisco 12000/10720 Router Manager Workflow

Figure 3-1Workflow for Cisco 12000/10720 Router Manager

 

 

 

 

 

 

 

 

 

 

 

 

 

Install Cisco EMF

 

 

 

 

 

 

 

software

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Install C12000/10720M

 

 

 

 

 

 

 

software

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start CEMF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start a Cisco EMF

 

 

 

 

 

 

 

session

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Deploy objects

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter username

 

 

 

 

 

 

 

and password

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Perform Subchassis

 

 

 

 

 

 

 

discovery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Review deployment

 

 

 

 

Layer 3 QoS

 

 

and check for alarms

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chassis

 

Module

 

Interface

 

 

ATM

Management

 

Management

 

Management

 

 

Connections

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fault

 

 

 

 

VLAN

 

 

Management

 

 

 

 

Sub-interface

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Change

 

 

 

 

 

 

 

Management

 

 

 

 

 

84835

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-2

OL-4455-01

 

 

Chapter 3 Getting Started

Starting Cisco EMF and Cisco 12000/10720 Router Manager

Starting Cisco EMF and Cisco 12000/10720 Router Manager

The Cisco 12000/10720 Router Manager application is viewed through the Cisco Element Management Framework (Cisco EMF). It is important to understand how Cisco EMF works before you use the Cisco 12000/10720 Router Manager application (refer to the Cisco Element Management Framework User Guide for further details). Cisco 12000/10720 Router Manager automatically starts when you start a Cisco EMF user session.

Note Each active Cisco EMF session uses a single Cisco EMF user license.

This section covers the following:

Starting a Cisco EMF User Session

Launchpad

Quitting a Cisco EMF User Session

Starting a Cisco EMF User Session

Note Cisco EMF should already be running. When you try to invoke a Cisco EMF session, and if you receive a message that Cisco EMF is not running, contact your system administrator, or refer to theCisco Element Management Framework User Guide for further details.

To start a Cisco EMF user session, proceed as follows:

Step 1 From the command line on the terminal window, enter <CEMF_ROOT>/bin/cemf session

Note <CEMF_ROOT> is the Cisco EMF installation root directory (for example, /opt/CEMF).

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-3

 

 

 

Chapter 3 Getting Started

Starting Cisco EMF and Cisco 12000/10720 Router Manager

The Login window (see Figure 3-2)appears.

Figure 3-2Login Window

Step 2 Enter a valid user name and password.

Step 3 ClickOk to proceed.

When an unknown user name or password is entered, an error is displayed. Click Ok, then enter a valid user name and password.

Note You have three attempts to enter a valid user name and password.After the third failed attempt the session does not start and the Login window closes.

When a valid user name and the password are entered, the session starts and the Cisco EMF Launchpad (see Figure 3-3)appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-4

OL-4455-01

 

 

Chapter 3 Getting Started

Starting Cisco EMF and Cisco 12000/10720 Router Manager

Launchpad

The icons displayed in the CEMF Manager and Event Manager panels on the Launchpad represent the applications provided by this Cisco EMF installation. Extra icons may appear when additional packages are installed. The icons (see Figure 3-3)represent the standard Cisco EMF tools.

Figure 3-3Launchpad

Viewer icon - Launches MapViewer

Groups icon - Launches the Object Group Manager

Access icon - Launches Access Manager

Events icon - Launches the Query Editor and Event Browser

Discovery icon - Launches Auto Discovery

80864

PreFilter icon - Launches Pre Filtering Application

Event Grps icon - Launches Event Groups Application

Thresholds icon - Launches Thresholding Regimes Application

Notify icon - Launches Notification Profile Application

Launching an Application

From the Launchpad, click the desired icon. The application is launched. A “busy” icon and a message in the status bar is displayed during launch. More than one instance of an application can be opened at any time.

Note If an application is already open, it appears in the Windows list. ClickWindow and choose the application you require from the drop down menu.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-5

 

 

 

Chapter 3 Getting Started

Starting Cisco EMF and Cisco 12000/10720 Router Manager

Map Viewer (Viewer)

MapViewer allows complete flexibility in viewing, building, and monitoring your network using graphical representations of network elements.

MapViewer is the primary entry point into the Cisco 12000/10720 Router Manager. When the MapViewer application is launched, a window appears corresponding to the highlighted map icon in the hierarchy pane. You can easily monitor the status of all network elements or abstractions of elements contained within the network and you can launch any of the additional applications on the Launchpad.

Refer to the Cisco Element Management Framework User Guide for further details on the MapViewer application.

Groups

Object Group Manager allows you to organize network elements into object groups. An object group is a collection of objects which are related in some way. They may all be the same type of equipment or all belong to the same customer.

Object groups can be built manually or by building a query. Some Cisco EMF subsystems may also build object groups which may be visible and usable by the Cisco EMF user.

Refer to the Cisco Element Management Framework User Guide for further details on the Object Group Manager application.

Access

User Access Control allows system administrators the opportunity to control the features of their system that can be accessed by various levels of personnel. This is important for secure network management.

Refer to the Cisco Element Management Framework User Guide for further details on the User Access Control application.

Event Browser (Events)

One of the most important aspects of Network Service Management is the ability to identify faults and other events on the network and to take action to resolve them quickly and efficiently. For example, there may be a power supply fault in a chassis which would require an engineer to be sent out to rectify the fault. This fault is critical to the running of the network and would need prompt attention.

In Cisco EMF, when a condition (fault) occurs on a managed object in the network, the system is notified immediately. Notification is shown as an event and can be viewed with the Event Browser (when configured to do so).

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the Event Browser application.

Discovery

Discovery allow you to examine the network for IP and SNMP devices and create a managed object for each new device discovered. Auto-discoverycan be opened from the Launchpad window or from a pop up menu available on selected objects.

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the Auto-discovery application.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-6

OL-4455-01

 

 

Chapter 3 Getting Started

Starting Cisco EMF and Cisco 12000/10720 Router Manager

Notification Profiles

An important aspect of a monitoring system which captures and reacts to events on the network is when and how a network operator is informed of these events. The Event Manager uses notifications for this. For example, when the temperature of a line card rises 10 degrees above normal an e-mailmight be sent to the network operator warning of a potential problem and a minor event might be generated if the temperature does not fall to within ten degrees of normal within twenty minutes.

Notification profiles are collections of notifications. Each notification profile has a name and description and can be accessed by all Event Manager users. Each includes a list of notifications, and is run following a trigger, which could be an event entering an event group, or a threshold breach in a thresholding regime. For example, when the first event is received by an event group a notification profile may be triggered which causes a sound to occur which alerts the operator. As well as audible alerts, a notification could be set up to display on screen, or to trigger an external notification such as an e-mail.

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the Notification Profiles application.

Thresholding Regimes

A Thresholding Regime is a set of threshold conditions for specified object attributes which, when breached, causes one or more notification profiles to be run. The Thresholding Regime defines which attributes should be polled and on what period, and defines the thresholding conditions. The Thresholding Regime specifies object groups which contain the objects whose attributes will be polled.

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the Thresholding Regimes application.

Event Groups

Event Groups allows you to organize network elements into event groups, and also view the status of these groups as scoreboards. Users can create, delete and modify event groups and scoreboards. Event groups are available to all users.

Event groups can be any combination of objects derived from the managed object class. These groups are set up using queries which can be configured to match your requirements. For example, you could choose to monitor a particular device, specify a time period, and choose to look at events which are warnings or critical. You define a query so that the event group only includes the events which meet the criteria you define. As soon as the group is created it starts monitoring against the criteria specified in the event query setup. Event groups created in the Event Groups application are persistent, they are not cleared when the application is closed.

The Event Groups application also enables you to view the events associated with an event group in a scoreboard format. This displays the overall status of the event group as a pie chart, with the associated severity color coding. A scoreboard also shows the total number of events which have entered the event group and the highest severity of the events in the group. An icon is displayed when a running notification has been set up for the event group.

Event Groups is opened from the Launchpad.

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the Event Groups application.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-7

 

 

 

Chapter 3 Getting Started

Deployment

PreFilter

Event pre-filteringallows any event generated by the network which matches the criteria established in the filter to be “filtered out”, and thus not saved into the database.

Pre-filteringoffers you the capability to eliminate unwanted or undesired events from entering the management system altogether.Pre-filteringis managed through the PreFilter application or from the Event Browser. The PreFilter application is launched via the PreFilter icon on the Launchpad.

The PreFilter manager window displays, listing each of the pre-filtersestablished, in the order in which they are to be processed (from top to bottom).

Refer to the Cisco Element Management Framework User Guide Release 3.2for further details on the PreFilter application.

Quitting a Cisco EMF User Session

To quit the current Cisco EMF session, proceed as follows:

Step 1 Choose File > Quit. You see the question Do you wish to quit the Cisco EMF Manager System?.

Step 2 ClickYes to quit the session (all active applications are closed and the session terminates) or clickNo to return to the current Cisco EMF session.

Deployment

The first step toward managing a Cisco 12000/10720 Router is to deploy or pre-deploythe physical objects that you want to manage. Deploying a physical object creates a representative object in Cisco EMF and as a result, makes the Cisco 12000/10720 Router Manager application aware of the physical object’s presence.

Cisco 12000/10720 Router Manager objects can be discovered automatically or deployed manually. For example, to deploy a chassis, you can use auto discovery or you can manually deploy the chassis. If you wish to deploy objects under the chassis, you can use subchassis discovery or manually deploy each object (interfaces are automatically created when you deploy each line card).

If all or most of your chassis objects are physically present and if you have a large amount of objects to deploy, you might want to automate these processes by using auto discovery. For example, if Cisco 12000/10720 Router Manager is installed into an existing network of Cisco 12000/10720 Routers, auto discovery can dramatically reduce the amount of operator input required. If you only want to deploy a few objects or if many of your objects are not yet physically present, you might want to deploy manually.

Cisco 12000/10720 Router Manager objects can be manually pre-deployedbefore the hardware arriveson-site.See“Pre-deployment” section on page 3-58 for further details.

The following supporting modules can be deployed using subchassis discovery only, no manual deployment is available for these modules:

AC or DC power supply card

Fan tray module

Blower module

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-8

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

You can also deploy either of the following logical objects:

SVC—See “Deploying an SVC Object” section on page 12-22

PVC—See “Deploying a PVC Object” section on page 12-18

VLAN Domain, VLAN and VLAN sub-interface—See“Deploying VLAN objects” section on page 13-4

Tip WRED (Weighted Random Early Detection) and CAR (Committed Access Rate) objects are not created using the deployment wizard. For details on creating these objects manually, seeChapter 11, “Layer 3 QoS.”

The Deployment section covers the following areas:

Deployment Process Outline

Manually Deploying a Generic Site Object

IP Auto Discovery of the Cisco Chassis

Manually Deploying a Cisco 12000/10720 Chassis

Commissioning and Subchassis Discovery

Manually Deploying Modules—Includesdeploying line cards for 12000 Series router chassis and10720 chassis

Pre-deployment

Deployment Process Outline

Producing a manageable Cisco 12000/10720 Router chassis in Cisco EMF is a three-stageprocess (seeFigure 3-4).

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-9

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-4Deployment Process Workflow

Stage 1: Manually

 

Stage 2: Chassis

deploy a generic object

 

level deployment

 

 

 

IP Auto-discoveryof

Cisco 12000/10720

series chassis

OR

Manual deployment of

the Cisco 12000/10720

series chassis

Stage 3: Sub-chassis

level deployment

Sub-chassis

Discovery

Optional AND/OR

Manually deploy

Sub-chassisobjects

84836

1.The first deployment stage is to manually deploy a Generic (Site) object. A Site object can be looked upon as a container object where you can deploy further objects that represent the

Cisco 12000/10720 Router chassis, line cards and interfaces contained within the chassis. See “Manually Deploying a Generic Site Object” section on page 3-10 for further details.

2.The second deployment stage is at the chassis level. The Cisco 12000/10720 Router chassis can be auto discovered or manually deployed. See “IP Auto Discovery of the Cisco Chassis” section on page 3-19 or the“Manually Deploying a Cisco 12000/10720 Chassis” section on page 3-20 for further details.

Note You canpre-deployobjects (that is, manually predeploy objects) before the Cisco hardware arriveson-site.See“Pre-deployment” section on page 3-58 for further details.

3.The third deployment stage is at subchassis level. This involves either subchassis discovery or deploying subchassis objects (modules) manually. See “Commissioning and Subchassis Discovery” section on page 3-26 or the“Manually Deploying Modules” section on page 3-30 for further details.

Manually Deploying a Generic Site Object

Generic objects are non-technologyspecific objects. When deploying a generic object, the information you are prompted to provide differs according to the type and number of generic objects you are deploying.

Table 3-1 displays a list of generic objects that can be deployed using Cisco 12000/10720 Router Manager.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-10

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Table 3-1Generic Object Deployment Templates

Object to be Deployed

Deployment Templates Available

 

 

Generic

Bay

 

 

 

IP Device

 

 

 

Region

 

 

 

SNMP Agent

 

 

 

SNMP MIB-2Agent

 

 

 

SNMP Proxied Device

 

 

 

Site

 

 

This section provided an example that shows how to deploy a Site object. The deployment process differs slightly for other types of generic object.

To deploy a Generic (Site) object, proceed as follows:

Step 1 Place the cursor over a relevant object to determine the objects you can deploy from. In this example we will deploy a Site object from the Physical view.

Step 2 Click and hold down the right mouse button.

Step 3 Choose Deployment>Deploy Generic Objects....

Figure 3-5Deploying a Site Object

The Deployment Wizard - Templates window appears (see Figure 3-6)displaying a list of available generic object deployment profiles. Deployment profiles are templates that prompt you for the appropriate information required to deploy the selected object successfully.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-11

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-6Deployment Wizard - Templates Window

Step 4 Select the generic object that you wish to deploy from the list supplied. In this example (shown inFigure 3-6)shows the deployment profile for a Site object is selected. The Deployment Wizard steps through a series of windows that prompt you for the information required to deploy the Site object.

Step 5 Click Forward.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-12

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

The Deployment Wizard - Object Parameters window appears (see Figure 3-7).

Figure 3-7Deployment Wizard - Object Parameters Window (1 of 2)

Step 6 Enter the number ofSites required. A single site was entered in this example.

Step 7 Click Forward.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-13

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-8Deployment Wizard - Object Parameters Window (2 of 2)

Step 8 Enter a Site name. Each Site must have a unique name. In this example the site is calledSite-srp.

Step 9 Click Forward.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-14

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

The Deployment Wizard - Views window appears.

Figure 3-9DeploymentWizard—ViewsWindow

Step 10 ClickSelect, to select a physical view.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-15

 

 

 

Chapter 3 Getting Started

Deployment

The Object Selector Window appears.

Figure 3-10Object Selector

Step 11 Select the object where you wish to place the Site object.

Step 12 ClickApply. The Deployment Wizard - Views windowre-appearswith the selection displayed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-16

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-11DeploymentWizard—ViewsWindow

Step 13 Click Forward.

Note You are prompted to repeat Steps 8 to 13 if you are deploying more than one Site.

The Deployment - Wizard Summary window appears. The Summary window provides details of the object you are about to deploy.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-17

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-12DeploymentWizard—SummaryWindow

Step 14 ClickFinish (when the Deployment Summary information is correct) to complete deployment and close the Deployment Wizard - Summary window. The new Site object (that is,Site-srp)is created and displayed in the Map Viewer window.

Figure 3-13Example Showing the Newly DeployedSite-srpObject

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-18

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Note This deployment procedure can be applied to the deployment of any of the generic objects although all of the steps may not apply to the particular generic object that you are deploying.

IP Auto Discovery of the Cisco Chassis

Auto discovery is the application that discovers existing Cisco 12000/10720 Routers, saving time and effort.

The auto discovery window can be opened from the Viewer or Discovery icon in the Launchpad. For further information, refer to the Cisco Element Management Framework User Guide.

The Auto discovery application has three mechanisms for discovering chassis:

IP—ICMPpings are used to find chassis in a given IP address range. This finds which IP devices exist, but does not discover what kind of device they are.

SNMP—SNMPget requests are used to find chassis in a given IP address range. Several SNMP community strings can be used so that equipment with different community strings can be discovered in the same discovery session. The SNMP information returned by devices is used to work out what kind of device has been found.

IP and SNMP—ICMPpings are used to find chassis and then SNMP requests are used to interrogate the chassis to find out what kind of chassis they are. This is the default mechanism.

Auto discovery can discover chassis on more than one subnetwork using multi-hopdiscovery. It can be scheduled to run at preset times (theCisco Element Management Framework User Guide details how to set the schedules).

After the chassis is detected, an object representing the chassis is created and placed under the site from which auto discovery was launched. A map of the chassis is also created, as shown in Figure 3-21 on page 3-26.

Note If you wish toauto-discovera chassis that can be managed by Cisco 12000/10720 Router Manager, then the Physical Path option must be enabled and an appropriate Physical Path (terminated with a Site) must be selected. Provided this is done, the auto discovery application will create a chassis below the selected Physical Path for each discovered chassis.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-19

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-14Example of Auto Discovery

Manually Deploying a Cisco 12000/10720 Chassis

Tip It is recommended that you ping the Cisco 12000/10720 Router you intend to deploy to ensure the device can be contacted.

To deploy a chassis, proceed as follows:

Step 1 In the Map Viewer, right click on the site object under which you wish to deploy the chassis, then choose

Deployment>Cisco 12000/10720 Manager>12008 or 12012 or 12016 or 12404 or 12406 or 12410 or 12416 or 10720>Chassis. The Deployment Wizard appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-20

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-15DeploymentWizard—ObjectParameters (1 of 3)

Step 2 Enter the number ofchassis objects you want to deploy. ClickForward.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-21

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-16DeploymentWizard—ObjectParameters Window (3 of 3)

Step 3 Enter the following information:

12000 Chassis Name—Typein a name (including prefix and suffix) for the chassis you are deploying. A default prefix appears (for example, “12008”). You can delete this prefix and use your own, or you can keep it and add your own suffix. This name must be unique.

IP Address—Typein the IP address for the chassis you are deploying.

Subnet Mask—Thesubnet mask for the IP address of the chassis.

SNMP Details—Typein the SNMP read and write communities, and select the SNMP version. The default SNMP version is 2c.

Chassis Initial State—Specifythe initial state for the chassis after deployment. The default initial state of the chassis is decommission. When the user selects commission, the chassis is automatically commissioned upon deployment.

Note Cisco 12000/10720 Router Manager allows the user to deploy a single chassis, more than once provided they have unique subnet masks.

Step 4 ClickForward to continue. The DeploymentWizard-Viewswindow appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-22

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-17DeploymentWizard—Views

Step 5 Click on Select. The Object Selector window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-23

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-18Object Selector Window

Step 6 Choose the site under which you want to deploy the chassis. Click Apply. The DeploymentWizard-Viewswindow is displayed with the selected Site object.

Figure 3-19DeploymentWizard—Views

Step 7 Click Forward. A Deployment Wizard Summary window is displayed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-24

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-20Deployment Wizard Summary

Step 8 The Deployment Summary details appear in the Deployment Summary Screen. If the Deployment Summary information is correct, clickFinish. If the Deployment Summary information is incorrect, clickCancel to stop deployment.

Step 9 To proceed, you have two options:

To perform subchassis discovery, see “Commissioning and Subchassis Discovery” section on page 3-26

If you wish to continue deploying individual modules, proceed to the “Manually Deploying Modules” section on page 3-30.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-25

 

 

 

Chapter 3 Getting Started

Deployment

Commissioning and Subchassis Discovery

After you deploy a chassis, the next step in creating a manageable system is to commission the chassis (which begins the process of subchassis discovery). Figure 3-21 shows a Cisco 12008 chassis map in the Physical view before subchassis discovery. Subchassis discovery discovers all physical objects (that is, modules and interfaces) within the chassis and places them onto the chassis map.

Figure 3-21Before Subchassis Discovery

Line cards and interfaces located within the chassis are discovered at this time. Commissioning not only discovers all the physical objects within the chassis, but also uploads the ATM connection objects (ATM PVC objects only) and initiates heartbeat polling that allows alarms to be raised on the chassis and all the physical objects within the chassis.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-26

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Because the chassis is the highest-levelobject, all objects under the chassis are commissioned as well when you commission the chassis. One level down, if you commission a GRP, you commission all physical objects underneath that level. If you commission a line card, you commission all interfaces on that line card, and so on. However, note that before you can commission any module within a chassis, the chassis object itself must be commissioned. This means that you must run subchassis discovery by commissioning the chassis before you can commission or decommission any individual objects under the chassis. If you do not want to actively manage all objects within the chassis, you can decommission the objects you are not ready to manage after commissioning the chassis.

Tip If you are not ready to commission the chassis, you can manually deploy modules within the chassis (for details, see“Manually Deploying Modules” section on page 3-30).Modules can also be commissioned individually, provided the chassis is commissioned.

Commissioning a Chassis

When you commission a chassis, subchassis discovery begins automatically. Subchassis discovery discovers and commissions all objects within the chassis. Commissioning automatically starts active management (such as polling) on the chassis and all commissioned objects within the chassis.

To commission a chassis, proceed as follows:

Step 1 It is recommended that the Cisco IOS Username and Passwords are set correctly before proceeding. Right click on the Site object that contains the chassis you wish to commission, then chooseCisco 12000/10720 Manager>Configuration>Chassis>Configuration. The Chassis Configuration window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-27

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-22Chassis Configuration Window

Step 2 Choose theChassis you want to commission from the list box at left of the window. Cisco 12000/10720 Router Manager allows you to select and commission multiple chassis simultaneously.

Note To select a contiguous block of chassis, click on the first chassis; then, without releasing the mouse button, drag to the last desired entry and release. A subsequent click anywhere on the window deselects all previous selections. To extend a currently selected block of chassis, hold theShift key down and click on the entry at the end of the group to be added. To add anon-contiguousentry to the selection group, hold down theCtrl (Control) key and click on the entry to be added. It is recommended to commission at the most 15 chassis at a time.

Step 3 Configure the parameters displayed on the Configuration and Additional Description tabs, as required.

Note See“Chassis Configuration” section on page 4-7 for detailed information on the Chassis Configuration window.

Step 4 ClickCommission (located in the Actions frame).

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-28

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

The chassis and all objects contained within are commissioned. A status report appears in the

Commission Status area displaying whether the commission action succeeded or failed.

Figure 3-23 shows a Cisco 12008 chassis map in the Physical view after successful subchassis discovery. Modules and interfaces are automatically deployed within the chassis and enter the commissioned state. However, icons representing the physical objects appear in the Component Managed view.

Figure 3-23After Subchassis Discovery

Note After commissioning a chassis you can configure and manage the chassis objects. SeeChapter 4, “Managing Chassis,” for further details.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-29

 

 

 

Chapter 3 Getting Started

Deployment

Decommissioning a Chassis

Decommissioning a chassis, decommissions all the objects within the chassis, and active management (such as polling) stops on the chassis and on all objects within the chassis.

To decommission a chassis, proceed as follows:

Step 1 Right click on the chassis you want to decommission, then chooseCisco 12000/10720 Manager>Configuration>Chassis>Configuration.

The Chassis Configuration window appears (see Figure 3-22).

Step 2 Choose theChassis you want to decommission in the Chassis list box at left of the window.

Step 3 ClickDecommission (located in the Actions area). The chassis and all objects contained within the chassis are decommissioned. A status report appears in the Commission Status area, which shows whether the action has succeeded or failed.

Object States

After subchassis discovery all objects enter a specific state. See “Cisco 12000/10720 Router Manager Object States” section on page 2-13 for details about object states.

Manually Deploying Modules

This section details the procedure to manually deploy modules using the Deployment Wizard. You can manually deploy modules before they are physically present (for details, see “Pre-deployment” section on page 3-58).In this scenario, you need to manually deploy modules, as a subchassis discovery will not pick up their presence. You can also decommission these modules if you do not want active management to be carried out on them.

Deployable modules include the following:

GRPs

Line cards (ATM, POS, Ethernet, DS-3,SRP or Modular Ethernet)

Tip Supporting modules, such as AC or DC power supply cards, fan tray modules, and blower modules, can only be deployed through subchassis discovery. You cannot manually deploy these modules.

Note Manual deployment of SRP Modules is currently not supported.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-30

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

User Named vs. Auto Named Module Deployment

When you deploy a module, you have two initial options:

To deploy an auto-namedmodule

To deploy a user-namedmodule

The user-namedoption allows you to name the module as you like. For example, if you have a specific naming scheme you want to use, then select theuser-namedoption.

The auto-namedoption assigns anauto-generatedname to the module, with the slot number appended to the name. For example, if you deployed anauto-namedATM line card in slot 5, the name given would be “A5.” This option is most useful when you have numerous line cards of the same type to deploy.

However, the line cards must be deployed in sequence within the slots. For example, if you wanted to deploy five ATM line cards in slots 1 to 5, then the auto-namedoption would be ideal.

Manually Deploying a GRP Card

Each chassis must have at least one GRP card deployed. A second optional GRP card can be deployed for the purpose of redundancy.

Note This feature is not applicable to the 10720 chassis

To deploy a GRP, proceed as follows:

Step 1 Right-clickon the slot within the chassis where you want the GRP to be deployed, then choose

Deployment>Cisco 12000/10720 Manager>Module>RP>GRP. The Deployment Wizard appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-31

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-24DeploymentWizard—Templates

Step 2 Choose one of the Template Choices from the list displayed (eitherauto-namedoruser-nameddeployment). Ensure that your choice is highlighted before continuing. See“User Named vs. Auto Named Module Deployment” section on page 3-31 for further information on auto vs. user named deployment.

Step 3 ClickForward. The Deployment Wizard - Object Parameters window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-32

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-25DeploymentWizard—ObjectParameters

Step 4 Enter the Number of GRP objects you wish to deploy. Enter in the slot number where you want the GRP to be deployed. If you are deploying two GRPs, the primary GRP must be placed in a slot with a lower number than the secondary GRP.

Caution If you deploy a module in a slot that is already occupied, deployment will fail at theFinish point. Also deployment fails, if a module is deployed with a name that already exists in the EM.

Step 5 ClickForward. The Deployment Wizard - Views window appears. Two Cisco 12000/10720 Router Manager views are displayed at the left side of the Deployment Wizard - Views window (that is, Physical and ComponentManaged).

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-33

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-26DeploymentWizard—Views

Step 6 ClickSelect. The Object Selector window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-34

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-27Object Selector Window

Step 7 Navigate through the hierarchy and choose the chassis that the GRP will be deployed within. Grayed out objects are not available for selection.

Step 8 ClickApply. The Deployment Wizard - Views windowre-appearswith the location where the object will be placed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-35

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-28DeploymentWizard—Views

Step 9 Repeat Steps 6 to 8 to place the chassis object in each of the Physical and ComponentManaged views.

Note You are prompted to repeat steps 6 to 8 if you are deploying more than one GRP card.

Step 10 ClickForward. The DeploymentWizard-Summarywindow appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-36

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-29DeploymentWizard—Summary

Step 11 The deployment summary details appear in the Deployment Summary window. If the deployment summary information is correct, clickFinish. If the deployment summary information is incorrect, clickCancel to stop deployment.

Note Two objects are deployed when deploying each GRP card: the GRP module object itself, and the Ethernet interface object, representing the Ethernet interface on the GRP.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-37

 

 

 

Chapter 3 Getting Started

Deployment

Manually Deploying Line Cards

The Cisco 12000 Series Router chassis supports six types of technology specific line cards (ATM, POS, Ethernet, SRP, DS-3and Modular Ethernet). SeeTable 3-2 toTable 3-7 for further details.

Line Cards Supported by Cisco 12000 Series Routers

Table 3-2 displays a list of the ATM line cards supported by Cisco 12000 Series Routers.

Table 3-2ATM Line Cards Supported by Cisco 12000 Series Routers

 

Cisco 12000/10720 Router

 

Card Type

Manager Menu Option

Card Description

 

 

 

atm-qoc3-sm

ATM > OC-34 > SM

4 Port OC3 ATM Single Mode (SM) Line Card

 

 

 

atm-qoc3-mm

ATM > OC-34 > MM

4 Port OC3 ATM Multi Mode (MM) Line Card

 

 

 

gsr-en-8oc3

ATM > OC-3-8> SM

GSR enhanced 8 port OC3c/STM-1ATM Line Card

 

 

 

sr-atm-en-8oc3-mm

ATM > OC-3-8> MM

GSR enhanced 8 port OC3c/STM-1Multimode ATM Line

 

 

Card

 

 

 

atm-oc12-sm

ATM > OC-121 > SM

Single Port OC-12Single Mode (SM) Line Card

 

 

 

atm-oc12-mm

ATM > OC-121 > MM

Single Port OC-12Multi Mode (MM) Line Card

 

 

 

gsr-qoc12-sm

ATM > OC-124> SM

4 port OC12 ATM Single Mode (SM) Line Card

 

 

 

gsr-qoc12-mm

ATM > OC-124 > MM

4 port OC12 ATM Multi Mode (MM) Line Card

 

 

 

gsr-e48-atm-4oc12-mm-sr-sc

cannot be manually deployed

GSR Edge Engine 48, ATM, 4 port OC12/STM4Multi

 

 

Mode Short Reach Line Card

 

 

 

gsr-e48-atm-4oc12-sm-ir-sc

cannot be manually deployed

GSR Edge Engine 48, ATM, 4 ports OC12/STM4 Single

 

 

Mode Intermediate Reach Line Card

 

 

 

Table 3-3 displays a list of the POS line cards supported by Cisco 12000 Series Routers.

Table 3-3POS Line Cards Supported by Cisco 12000 Series Routers

POS

 

 

 

 

Cisco 12000/10720 Router Manager

 

 

 

 

Card Type

Menu Option

Card Description

 

 

 

 

 

 

pos-qoc3-sm

POS > OC-34 > E4 SM

4

Port Packet Over SONET OC-3c/SMSingle

 

 

 

 

 

Mode Line Card

 

 

 

 

 

pos-qoc3-sm-l

POS > OC-34 > E4SM-LR

4 Port Packet Over SONET OC-3c/STM-1Single

 

 

 

 

 

Mode Long Reach Line Card

 

 

 

 

 

 

pos-qoc3-mm

POS > OC-34 > E4 MM

4

Port Packet Over SONET OC-3c/MMMulti

 

 

 

 

 

Mode Line Card

 

 

 

 

 

 

gsr-e48-pos-4oc3-mm-sr-mtrj

POS > OC-34 > E4+MM-SR

4

Port POS OC 48 Multi Mode Short Reach Line

 

 

 

 

 

Card

 

 

 

 

 

 

gsr-e48-pos-4oc3-sm-lr-lc

POS > OC-34 > E4+SM-LR

4

Port POS OC 48 Single Mode long Reach Line

 

 

 

 

 

Card

 

 

 

 

 

 

gsr-e48-pos-4oc3-sm-ir-lc

POS > OC-34 > E4+>SM-IR

4

Port POS OC 48 Single Mode Intermediate

 

 

 

 

 

Reach Line Card

 

 

 

 

 

 

 

 

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3-38

 

 

 

 

OL-4455-01

 

 

 

 

 

 

 

Chapter 3 Getting Started

Deployment

Table 3-3POS Line Cards Supported by Cisco 12000 Series Routers (continued)

POS

 

Cisco 12000/10720 Router Manager

 

 

Card Type

Menu Option

Card Description

 

 

 

 

pos-8oc3-mm

POS > OC-38 Port > E4 MM

8

Port OC3 Multimode POS

 

 

 

 

pos-8oc3-ir

POS > OC-38 Port > E4 SM

8

Port OC3 SM Intermediate Reach POS

 

 

 

pos-8oc3-lr

POS > OC-38 Port > E4SM-LR

8 port OC3 SM Long Reach POS

 

 

 

 

gsr-e48-pos-8oc3-mm-sr-mtrj

POS > OC-38 Port > E4+MM-SR

8

Port POS OC 3 multi MOde Short Reach Line

 

 

Card

 

 

 

gsr-e48-pos-8oc3-sm-ir-lc

POS > OC-38 Port > E4+SM-IR

8 Port POS OC 3 Single Mode Intermediate Reach

 

 

Line Card

 

 

 

 

pos-oc12-sm

POS > OC-121 Port > SM

1

Port Packet Over SONET OC-12Single Mode

 

 

(SM) Line Card

 

 

 

 

pos-oc12-mm

POS > OC-121 Port > MM

1

Port Packet Over SONET OC-12Multi Mode

 

 

(MM) Line Card

 

 

 

 

pos-qoc12-sm-lr

POS > OC-124 Port > SM

4

Port (Quad) OC-12POS Card, Single Mode,

 

 

Long Reach

 

 

 

pos-qoc12-mm-sr

POS > OC-124 Port > MM

4 port (Quad) OC-12POS Card, Single Mode,

 

 

Short Reach

 

 

 

pos-en-qoc12-sr

POS > Enhanced OC-124 Port > MM

Enhanced 4 Port OC-12Short Reach Line Card

 

 

 

pos-en-qoc12-ir

cannot be manually deployed

Enhanced 4 port OC-12Intermediate Reach Line

 

 

Card

 

 

 

 

pos-oc48-sm-lr-fc

POS > OC-48>LR-FC

1

Port Packet Over Sonet OC-48,Single Mode,

 

 

Long Reach, FC Connector Card

 

 

 

 

pos-oc48-sm-lr-sc

POS > OC-48>LR-SC

1

Port Packet Over Sonet OC-48,Single Mode,

 

 

Long Reach, SC Connector Card

 

 

 

 

pos-oc48-sm-sr-fc

POS > OC-48>SR-FC

1

Port Packet Over SONET OC-48c/STM-16

 

 

Single Mode Short Reach with FC Connector

 

 

 

 

pos-oc48-sm-sr-sc

POS > OC-48>SR-SC

1

Port Packet Over Sonet OC-48,Single Mode,

 

 

Short Reach, SC Connector Card

 

 

 

pos-en-oc48-lr-fc

POS > Enhanced OC-48>LR-FC

Enhanced OC-48Long Reach FC Connector Line

 

 

Card

 

 

 

pos-en-oc48-lr-sc

POS > Enhanced OC-48>LR-SC

Enhanced OC-48Long Reach SC Connector Line

 

 

Card

 

 

 

pos-en-oc48-sr-fc

POS > Enhanced OC-48>SR-FC

Enhanced OC-48Short Reach FC Connector Line

 

 

Card

 

 

 

pos-en-oc48-sr-sc

POS > Enhanced OC-48>SR-SC

Enhanced OC-48Short Reach SC Connector Line

 

 

Card

 

 

 

 

pos-en-qoc48-sm-sr-sc

POS > Enhanced OC-484 > E4

4

Port (Quad) Enhanced OC-48Short Reach SC

 

SR-SC

Connector Line Card

 

 

 

 

pos-en-qoc48-sm-sr-fc

POS > Enhanced OC-484 > E4

4

Port (Quad) Enhanced OC-48Short Reach FC

 

SR-FC

Connector Line Card

 

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-39

 

 

 

Chapter 3 Getting Started

Deployment

Table 3-3POS Line Cards Supported by Cisco 12000 Series Routers (continued)

POS

 

 

 

 

Cisco 12000/10720 Router Manager

 

 

 

Card Type

Menu Option

Card Description

 

 

 

 

 

pos-en-qoc48-sm-lr-sc

POS > Enhanced OC-484 > E4

4 Port (Quad) Enhanced OC-48Long Reach SC

 

 

 

 

LR-SC

Connector Line Card

 

 

 

 

 

pos-en-qoc48-sm-lr-fc

POS > Enhanced OC-484 > E4

4 Port (Quad) Enhanced OC-48Long Reach FC

 

 

 

 

LR-FC

Connector Line Card

 

 

 

 

 

gsr-e-qoc48-sm-sr-sc

POS > Enhanced OC-484 > E4+

4 Port Enhanced OC 48 Short Reach SC

 

 

 

 

SR-SC

Connector Line Card

 

 

 

 

 

gsr-e-qoc48-sm-sr-fc

POS > Enhanced OC-484 > E4+

4 Port Enhanced OC 48 Short Reach FC

 

 

 

 

SR-FC

Connector Line Card

 

 

 

 

 

gsr-e-qoc48-sm-lr-sc

POS > Enhanced OC-484 > E4+

4 Port Enhanced OC 48 Long Reach SC Connector

 

 

 

 

LR-SC

Line Card

 

 

 

 

 

gsr-e-qoc48-sm-lr-fc

POS > Enhanced OC-484 > E4+

4 Port Enhanced OC 48 Long Reach FC Connector

 

 

 

 

LR-FC

Line Card

 

 

 

 

 

pos-oc192-sm-sr-sc

POS > OC-1921 > E4SR-SC

OC-192Short Reach SC Connector Line Card

 

 

 

 

 

pos-oc192-sm-sr-fc

POS > OC-1921 > E4SR-FC

OC-192Short Reach FC Connector Line Card

 

 

 

 

 

pos-oc192-sm-ir-sc

POS > OC-1921 > E4IR-SC

OC-192Intermediate Reach SC Connector Line

 

 

 

 

 

Card

 

 

 

 

 

pos-oc192-sm-ir-fc

POS > OC-1921 > E4IR-FC

OC-192Intermediate Reach FC Connector Line

 

 

 

 

 

Card

 

 

 

 

 

pos-en-oc192-sm-vsr

POS > OC-1921 > E4 VSR

Enhanced OC-192Very Short Reach Line Card

 

 

 

 

 

gsr-e-oc192-sm-sr2-sc

POS > OC-1921 > E4SR2-SC

GSR Edge 1 Port OC 192 Short Reach 2 SC

 

 

 

 

 

Connector Line Card

 

 

 

 

 

gsr-e-oc192-sm-sr2-fc

POS > OC-1921 > E4SR2-FC

GSR Edge 1 Port OC 192 Short Reach 2 FC

 

 

 

 

 

Connector Line Card

 

 

 

 

 

pos-en-oc192-sm-sr2-sc

POS > OC-1921 > E4+SR2-SC

Enhanced 1 Port OC 192 Short Reach 2 SC

 

 

 

 

 

Connector Line Card

 

 

 

 

 

pos-en-oc192-sm-sr2-fc

POS > OC-1921 > E4+SR2-FC

Enhanced 1 Port OC 192 Short Reach 2 FC

 

 

 

 

 

Connector Line Card

 

 

 

 

 

gsr-e-oc192-sm-sr-sc

POS > OC-1921 > E4+SR-SC

1 Port OC 192 Short Reach SC Connector Line

 

 

 

 

 

Card

 

 

 

 

 

gsr-e-oc192-sm-sr-fc

POS > OC-1921 > E4+SR-FC

1 Port OC 192 Short Reach FC Connector Line

 

 

 

 

 

Card

 

 

 

 

 

gsr-e-oc192-sm-ir-sc

POS > OC-1921 > E4+IR-SC

1 Port OC 192 Intermediate Reach SC Connector

 

 

 

 

 

Line Card

 

 

 

 

 

gsr-e-oc192-sm-ir-fc

POS > OC-1921 > E4+IR-FC

1 Port OC 192 Intermediate Reach FC Connector

 

 

 

 

 

Line Card

 

 

 

 

 

gsr-e-oc192-vsr

POS > OC-1921 > E4+VSR-SC

Enhanced OC-192Very Short Reach SC

 

 

 

 

 

Connector Line Card

 

 

 

 

 

pos-16oc3-lr

POS > OC-316 > E4 LR

16 Port OC3 SM long Reach POS

 

 

 

 

 

 

 

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3-40

 

 

 

OL-4455-01

 

 

 

 

 

 

Chapter 3 Getting Started

Deployment

Table 3-3POS Line Cards Supported by Cisco 12000 Series Routers (continued)

POS

 

Cisco 12000/10720 Router Manager

 

 

 

Card Type

Menu Option

Card Description

 

 

 

 

pos-16oc3-ir

POS > OC-316 > E4 SM

16 Port OC3 SM Intermediate Reach POS

 

 

 

 

pos-16oc3-mm

POS > OC-316 > E4 MM

16 Port OC3 Multi Mode POS

 

 

 

 

gsr-e48-pos-16oc3-mm-sr-mtrj

POS> OC-316 > E4+MM-SR

16 Port OC3 Multi Mode Short Reach POS

 

 

 

 

gsr-e48-pos-16oc3-sm-ir-lc

POS > ISE > OC-316 > IR

16 Port OC3 SM Intermediate Reach POS

 

 

 

 

 

gsr-e48-pos-qoc12-sm-ir-sc

POS > ISE > OC-124 > IR

4

Port OC12 SM Intermediate Reach POS

 

 

 

 

 

gsr-e48-pos-oc48-sm-ir-lc

POS > ISE > OC-481> IR

1

Port OC48 Intermediate Reach POS

 

 

 

 

 

gsr-e48-pos-oc48-sm-sr

POS > ISE > OC-481> SR

1

Port OC48 Short Reach POS

 

 

 

 

 

gsr-e48-pos-oc48-sm-lr

POS > ISE > OC-481> LR

1

Port OC48 Long Reach POS

 

 

 

 

Table 3-4 displays a list of the Ethernet line cards supported by Cisco 12000 Series Routers.

Table 3-4Ethernet Line Cards Supported by Cisco 12000 Series Routers

 

 

 

 

 

 

 

 

Cisco 12000/10720 Router Manager

 

 

 

Card Type

Menu Option

Card Description

 

 

 

 

 

gsr-1ge

Ethernet > Giga > 1 Port

1

Port Gigabit Ethernet Line Card

 

 

 

 

 

gsr-3ge

Ethernet > Giga > 3 Port

3

Port Gigabit Ethernet Line Card (trident)

 

 

 

 

gsr-10pge

Ethernet>Giga > 10 Port

10 port Gigabit Ethernet Line Card

 

 

 

 

gsr-8fe-tx

Ethernet > Fast > 8 Port > Copper

8 port Fast Ethernet card with Copper Interface

 

 

 

 

gsr-8fe-fx

Ethernet > Fast > 8 Port > Fiber

8 port Fast Ethernet card with Fiber Interface

 

 

 

 

 

gsr-1p10ge

Ethernet > 10Giga > 1 Port

1

Port 10Giga Ethernet Line Card

 

 

 

 

gsr-pa-1ge

Ethernet > Modular > Gigabit/

1 Port Modular Gigabit Fast Ethernet Line Card

 

FastEthernet Card

 

 

 

 

 

 

 

 

gsr-pa-3ge

Ethernet > Modular > Port Adaptor >

3

Port Modular Port Adaptor Gigabit Line Card

 

3 Port Gigabit

 

 

 

 

 

 

 

gsr-pa-24fe

Ethernet > Modular > Port Adaptor >

24 Port Modular Port Adaptor Fast Ethernet

 

24 Port FastEthernet

Line Card

 

 

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-41

 

 

 

Chapter 3 Getting Started

Deployment

Table 3-5 displays a list of theDS-3line cards supported by Cisco 12000 Series Routers.

Table 3-5DS-3Line Cards Supported by Cisco 12000 Series Routers

 

Cisco 12000/10720 Router Manager

 

Card Type

Menu Option

Card Description

 

 

 

copper-6ds3

DS3 > 6 Port

6 Port Copper DS3 Interface Line Card

 

 

 

copper-12ds3

DS3 > 12 Port

12 Port Copper DS3 Interface Line Card

 

 

 

Table 3-6 displays a list of the E3 line cards supported by Cisco 12000 Series Routers.

Table 3-6

E3 Line Cards Supported by Cisco 12000 Series Routers

 

 

 

 

 

 

 

Cisco 12000/10720 Router Manager

 

Card Type

 

Menu Option

Card Description

 

 

 

 

copper-6e3

 

E3 > 6 Port

6 Port E3 Interface Line Card

 

 

 

 

copper-1e3

 

E3 > 12 Port

12 Port E3 Interface Line Card

 

 

 

 

Table 3-7 displays a list of the SRP line cards supported by Cisco 12000 Series Routers.

Table 3-7SRP Line Cards Supported by Cisco 12000 Series Routers

 

Cisco 12000/10720 Router Manager

 

Card Type

Menu Option

Card Description

 

 

 

srp-oc12-sm-ir

cannot be manually deployed

1 Port OC-12Single Mode SRP Intermediate

 

 

Reach Line Card

 

 

 

srp-oc12-mm

cannot be manually deployed

1 Port OC-12Multi Mode SRP Line Card

 

 

 

srp-oc48-sm-sr

cannot be manually deployed

1 Port OC-48SRP Single Mode Short Reach

 

 

Line Card

 

 

 

srp-oc48-sm-lr

cannot be manually deployed

1 Port OC-48SRP Single Mode Long Reach

 

 

Line Card

 

 

 

ssrp-e48-2oc12-sm-ir

cannot be manually deployed

2 Port OC 12 Single Mode Intermediate

 

 

Reach Line Card

 

 

 

ssrp-e48-2oc12-sm-xr

cannot be manually deployed

2 Port OC 12 Single Mode Line Card

 

 

 

ssrp-oc192-sm-lr

cannot be manually deployed

GSR 1 port SONET based SRP

 

 

OC-192c/STM-64

 

 

 

ssrp-oc192-sm-ir

cannot be manually deployed

OC 192 Single Mode Intermediate Reach

 

 

Line Card

 

 

 

ssrp-oc192-sm-sr

cannot be manually deployed

OC 192 Single Mode Short Reach Line Card

 

 

 

ssrp-oc192-sm-vsr

cannot be manually deployed

OC 192 Single Mode Very Short Reach Line

 

 

Card

 

 

 

gsr-dtp-dense48

cannot be manually deployed

A dual mode card. It can function as a

 

 

4xOC48 or 2xSRP48

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-42

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Line Cards Supported by Cisco 10720 Routers

Table 3-8 displays a list of the SRP line cards supported by Cisco 10720 Routers.

Table 3-8SRP Line Cards Supported by Cisco 10720 Routers

 

Cisco 12000/10720 Router Manager

 

Card Type

Menu Option

Card Description

 

 

 

srp-oc48-sr

cannot be manually deployed

1 port OC-48cSRP SM short reach uplink card

 

 

 

srp-oc48-ir

cannot be manually deployed

1 port OC-48cSRP SM intermediate reach

 

 

uplink card

 

 

 

ul-srp48-lr1

cannot be manually deployed

1 port OC-48cSRP SM long (40km) reach

 

 

uplink card

 

 

 

ul-srp48-lr2

cannot be manually deployed

1 port OC-48cSRP SM long (80km) reach

 

 

uplink card

 

 

 

ul-pos-srp48-sm-sr

POS > SR

c10720 OC-48cPOS/SRP SM short reach

 

 

uplink card

 

 

 

ul-pos-srp48-sm-ir

POS > IR

c10720 OC-48cPOS/SRP SM intermediate

 

 

reach uplink card

 

 

 

ul-pos-srp48-sm-lr1

POS > LR1

c10720 OC-48cPOS/SRP SM Long Reach

 

 

(40Km) uplink card

 

 

 

ul-pos-srp48-sm-lr2

POS > LR2

c10720 OC-48cPOS/SRP SM Long Reach

 

 

(80Km) uplink card

 

 

 

Table 3-9 displays a list of the Ethernet line cards supported by Cisco 10720 Routers.

Table 3-9Ethernet Line Cards Supported by Cisco 10720 Routers

 

Cisco 12000/10720 Router Manager

 

Card Type

Menu Option

Card Description

 

 

 

acc-24fe-tx

Fast > 24 Port

24 port fast Ethernet TX access card

 

 

 

acc-24fe-fx-mm

Fast > 24 Port

24 port fast Ethernet FX MM (2km) access card

 

 

 

acc-24fe-fx-sm

Fast > 24 Port

24 port fast Ethernet FX SM (15km) access card

 

 

 

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-43

 

 

 

Chapter 3 Getting Started

Deployment

To deploy a line card of any type, proceed as follows:

Step 1 Right click on the chassis object under which you want to deploy the line card, then choose

Deployment>Cisco 12000/10720 Manager>Module>ATM or POS or Ethernet or DS-3, then choose the exact type of line card to be deployed (for example, OC-3 4 Port or OC12 1 Port). Now, choose the exact variant (for example, SM, or MM) if applicable.

The Deployment Wizard appears.

Figure 3-30DeploymentWizard—Templates

Step 2 Choose the type of deployment (eitherauto-namedoruser-named).

Step 3 Click Forward.

Note The sample windows displayed are for an ATMOC-34 port MM line card.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-44

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-31DeploymentWizard—ObjectParameters

Step 4 Enter the number of line card objects you want to deploy.

Step 5 Enter the slot number where the card will be deployed.

Note Deployment will fail (at theFinish point later on) if you try to deploy a module in a slot that is already occupied.

Step 6 ClickForward. The Deployment Wizard - Views window appears. Two Cisco 12000/10720 Router Manager views are displayed at the left side of the Deployment Wizard - Views window (that is, Physical and ComponentManaged).

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-45

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-32DeploymentWizard—Views

Step 7 ClickSelect to choose where you wish to place the object within the view. The Object Selector window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-46

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-33Object Selector Window

Step 8 Choose the chassis you want to place the ATM line card under. Objects which are not available for selection are greyed out. Click on the + sign to expand the view. Select the chassis under which you want to deploy the line card.

Step 9 Once you have highlighted your selection, clickApply. The Deployment Wizard - Views windowre-appearswith the location where the object will be placed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-47

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-34DeploymentWizard—Views

Step 10 Repeat Steps 7 to 9 to place the object in each of the Physical and ComponentManaged views.

Step 11 Click Forward.

Note You are prompted to repeat steps 4 through 11 if you are deploying multiple line cards.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-48

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

The Deployment Wizard—Summarywindow appears.

Figure 3-35DeploymentWizard—Summary

Step 12 The deployment summary details appear in the Deployment Summary window. If the information is correct, clickFinish. ClickCancel if the information is incorrect, and the deployment process stops.

Note The number of objects deployed reflects the line card object plus the number of ports or interfaces on the line card. For example, if you have deployed anOC-34 port line card, 5 objects are deployed in total. The five objects are four interfaces and the actual line card.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-49

 

 

 

Chapter 3 Getting Started

Deployment

Manually Deploying Supporting Modules

The Cisco 12000 Series Router chassis support the following supporting modules:

Clock Scheduler Cards (CSCs)

Switch Fabric Cards (SFCs)

AC Power supply modules

Fan tray modules

Blower modules

Note The AC power supply, fan tray and blower modules can only be discovered during subchassis discovery (that is, they cannot be manually deployed).

The Cisco 12000 Series Router chassis supports the following CSC and SFC line cards. See Table 3-10 for further details.

Table 3-10Cisco 12000/10720 Router Manager Supported CSC and SFC Line Cards

Card

Card Type

Card Description

 

 

 

CSC

CSC0

OC48 Clock Scheduler Card

 

 

 

 

CSC4

OC48 ClockScheduler Card

 

 

 

 

CSC8

OC48 Clock Scheduler Card

 

 

 

 

CSC16

OC48 Clock Scheduler Card for 12016 chassis

 

 

 

 

CSC16XOC192

OC192 Clock Scheduler Card for 12416 chassis

 

 

 

 

CSC10XOC192

OC192 Clock Scheduler Card for 12410 chassis

 

 

 

 

CSC6XOC192

OC192 Clock Scheduler Card for 12406 chassis

 

 

 

 

CSCSFC64

Combined CSC-SFCcard for 12404 chassis

 

 

 

SFC

SFC0

OC48 Switch Fabric Card

 

 

 

 

SFC8

OC48 Switch Fabric Card

 

 

 

 

SFC16

OC48 Switch Fabric Card for 12016 chassis

 

 

 

 

SFC16XOC192

OC192 Switch Fabric Card for 12416 chassis

 

 

 

 

SFC10XOC192

OC192 Switch Fabric Card for 12410 chassis

 

 

 

 

SFC6XOC192

OC192 Switch Fabric Card for 12406 chassis

 

 

 

Deploying a Clock Scheduler Card

To deploy a clock scheduler card (CSC), proceed as follows:

Step 1 Right click on the chassis under which you want to deploy the CSC, then choose the correct CSC card from the service menuDeployment>Cisco 12000/10720 Manager>Module>CSC. The DeploymentWizard—Viewswindow appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-50

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-36DeploymentWizard—Views

Step 2 ClickSelect to choose where you wish to place the object within the view. Click on the + sign to expand the view if required. The Object Selector window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-51

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-37Object Selector Window

Step 3 Navigate through the hierarchy and choose where you wish to place the object within the view. Click on the + sign to expand the view if required.

Step 4 ClickApply. The Deployment Wizard - Views windowre-appearswith the location where the object will be placed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-52

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-38DeploymentWizard—Views

Step 5 ClickForward. The DeploymentWizard—Summarywindow appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-53

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-39DeploymentWizard—Summary

Step 6 The deployment summary details appear in the Deployment Summary window. If the information is correct, clickFinish. If the information is incorrect, clickCancel to stop deployment.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-54

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Deploying a Switch Fabric Card

To deploy a switch fabric card (SFC), proceed as follows:

Step 1 Right click on the chassis you want to deploy the switch fabric card under, then choose the correct SFC card from the service menuDeployment>Cisco 12000/10720 Manager>12008>Module>SFC. The DeploymentWizard—Viewswindow appears.

Figure 3-40DeploymentWizard—Views

Step 2 ClickSelect to choose where you wish to place the object within the view. The Object Selector window appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-55

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-41Object Selector Window

Step 3 Choose where you wish to place the object within the view. Click on the + sign to expand the view if required.

Step 4 ClickApply. The Deployment Wizard - Views windowre-appearswith the location where the object will be placed.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-56

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Figure 3-42DeploymentWizard—Views

Step 5 Repeat Steps 2 to 4 to place the object in each of the Physical and ComponentManaged views.

Step 6 ClickForward. The DeploymentWizard—Summarywindow appears.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-57

 

 

 

Chapter 3 Getting Started

Deployment

Figure 3-43DeploymentWizard—Summary

Step 7 The deployment summary details appear in the Deployment Summary window. If the information is correct, clickFinish. If the information is incorrect, clickCancel to stop deployment.

Pre-deployment

Cisco 12000/10720 Router Manager objects can be manually pre-deployedbefore the equipment arriveson-site.The following objects can bepre-deployedin Cisco 12000/10720 Router Manager:

Cisco 12000/10720 Router chassis

Line cards and interfaces

For example, if you know that you will be receiving a certain line card, you can manually predeploy that line card before it is actually present.

Note Manual Deployment of SRP modules is currently not supported.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-58

OL-4455-01

 

 

Chapter 3 Getting Started

Deployment

Performing Pre-deployment

Say that you are expecting the following hardware:

Cisco 12016 chassis and GRP(s)

ATM and POS line cards (with respective interfaces)

To perform both manual pre-deploymentand offline configuration, proceed as follows:

Step 1 Manually deploy a site object. See “Manually Deploying a Generic Site Object” section on page 3-10 for further details.

Step 2 Manually deploy the Cisco 12000 Series Router chassis under a site. See“Manually Deploying a Cisco 12000/10720 Chassis” section on page 3-20 for further details.

Step 3 Manually deploy GRP(s). See “Manually Deploying a GRP Card” section on page 3-31 for further details.

Step 4 Manually deploy the ATM line cards. ATM interfaces are deployed simultaneously. See“Manually Deploying Line Cards” section on page 3-38 for further details.

Step 5 Manually deploy the POS line cards. POS interfaces are deployed simultaneously. See“Manually Deploying Line Cards” section on page 3-38 for further details.

Now you have pre-deployedand thus created representative objects in Cisco 12000/10720 Router Manager for your expected hardware, modules, and interfaces. All of these objects will be in the Decommissioned state.

Cisco 12000/10700 v3.1.1 Router Manager User Guide

 

OL-4455-01

3-59

 

 

 

Chapter 3 Getting Started

Deployment

Cisco 12000/10700 v3.1.1 Router Manager User Guide

3-60

OL-4455-01