Cisco Systems UNIFIED COMMUNICATIONS UC320W User Manual

Size:
151.29 Kb
Download

Quick Start Guide

Cisco Small Business

Unified Communications UC320W with FXO

Package Contents

Unified Communications System

Ethernet Network Cable

Phone Cable

Power Adapter

Power Cord Retention Kit

Quick Start Guide

Phone Quick Reference Card

Product CD-ROM

CAUTION Be sure to read Section 1 before installation.

Welcome

Thank you for choosing the Cisco Small Business Unified Communications Model UC320W. This guide describes how to install the equipment and get started configuring the system.

1 Before You Begin

Minimum Requirements

Computer with web browser. Cisco recommends Internet Explorer version 7 or later or Firefox version 3.6 or later.

Adobe Flash Player version 10.1 or later.

Cisco SPA300 Series or Cisco SPA500 Series IP phones.

Power adapters for the phones, as needed. Cisco SPA300 Series phones always require power adapters. Cisco SPA500 Series phones can receive power from a Power over Ethernet switch.

Ethernet cables to connect IP phones and computers.

Internet service.

Voice over IP service or analog phone service.

Optional: 2GB+ USB Flash key (FAT32 format) for site backups.

Default Settings

Parameter

Default Value

 

 

Username

cisco

 

 

Password

cisco

 

 

LAN IP

192.168.10.1

(Also the address for the web-based

 

configuration utility.)

 

 

 

DHCP Range

192.168.10.100 to 149

(DHCP server is enabled by default.)

 

 

 

Netmask

255.255.255.0

 

 

Voice VLAN

100

 

 

Default Voice VLAN Subnet

10.1.1.1

 

 

NOTE To restore these default settings at any time: Using a paperclip or similar object, press and hold the Reset button on the side panel for 10 seconds.

CAUTION Before installing the Cisco UC320W into an existing network with another DHCP server, refer to the Smart Designs (see links onpage 4). IP address conflicts will result if two DHCP servers are installed on your network.

2

Cisco UC320W Quick Start Guide

2 Installation and Configuration

1Connect a network cable from the WAN port of the Cisco UC320W to your Internet Service or Internet access device.

2Connect the supplied power cord to the POWER port and to a power outlet. When the device is fully booted, the POWER/SYS light is steady green.

3Connect your computer to a LAN port on the Cisco UC320W. Do not connect any devices to the LAN ports at this point. Your computer will receive an IP address in the 192.168.10.x range.

NOTE:

You may need to adjust your computer’s connecting settings to receive an IP address dynamically.

For best results, set the screen resolution to 1024x768 or higher.

4Start a web browser. In the Address bar, enter the IP address of the Cisco UC320W (default 192.168.10.1).

5To log in, enter the username cisco and the passwordcisco. Both the username and the password are case sensitive.

6When prompted, enter a new username and password. Neither cisco noradmin is valid.

7Follow the instructions in the configuration utility to connect the equipment and configure the system.

NOTE:

If you are installing the Cisco UC320W in a network with another DHCP server, complete the Network Topology step in the Getting Started menu.

For best results, complete the Upgrade Firmware task and accept all available firmware updates.

3 Getting to Know the Cisco UC320W

1

2

3

4

5

6

7

 

4

 

 

3

2

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LINE (FXO)

 

 

 

 

 

PHONE

 

 

 

 

 

 

 

 

 

 

 

(FXS)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

3

2

1

 

 

WAN

LAN (10/100/1000)

LINE

LINE

Power

(10/100/1000)

OUT

IN

12VDC

195714

1

LINE (FXO) Connect phone lines for traditional phone service.

 

 

 

 

2

PHONE (FXS) Connect an analog device, such as a phone.

 

 

 

3

WAN Connect to your broadband network access device or to an uplink port

 

on an Ethernet switch that is connected to the Internet.

 

 

 

 

4

LAN Connect IP phones and other network devices.

 

 

 

 

Cisco UC320W Quick Start Guide

3

78-19296-01 C0

5LINE OUT Connect to an external speaker system.

6LINE IN Connect to an external music source for Music On Hold service (optional).

7POWER Connect to a power source. Use only the provided power adapter. Optionally, you can use the power cord retention clamp to prevent accidental removal of the power cord. See instructions in the Cisco UC320W administration guide.

4 Where to Go From Here

Support

Cisco Small Business Support

www.cisco.com/go/smallbizsupport

Community

 

 

 

Cisco Small Business Support

www.cisco.com/go/smallbizhelp

and Resources

 

 

 

Phone Support Contacts

www.cisco.com/go/sbsc

 

 

Product Documentation

 

 

 

Cisco UC320W, SPA300 and

www.cisco.com/go/uc300

SPA500 Series IP Phones

 

 

 

Smart Designs (design and

www.cisco.com/go/partner/smartdesigns

implementation guides)

 

 

 

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706USA

www.cisco.com

Small Business Support US: 1-866-606-1866(Toll Free, 24/7)

Small Business Support, Global: www.cisco.com/go/sbsc

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/ trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

© 2011 Cisco Systems, Inc. All rights reserved.