Cisco Systems UBR10-FAN-CAB, UBR10-FAN-ASSY User Manual

0 (0)
Cisco Systems UBR10-FAN-CAB, UBR10-FAN-ASSY User Manual

Cisco uBR10012 Universal Broadband Router

Fan Assembly Module

Document Part Number: OL-5093-01

October 2003

Product Numbers: UBR10-FAN-ASSY=, UBR10-FAN-CAB=

Revision History

Date

Revision

Reason

 

 

 

08/31/2001

78-11491-01

Original publication. This document is obsolete.

 

 

 

10/21/03

OL-5093-01

Moved document to online only, updated information and format.

 

 

 

Purpose

The purpose of this document is to provide installation, removal, and troubleshooting information for the fan assembly module installed in the Cisco uBR10012 universal broadband router.

Audience

This document is intended for use by a field service engineer who is familiar with Cisco products and headend cable installation procedures.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030.

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 2003 Cisco Systems, Inc. All rights reserved.

Scope

This document includes procedures for installing and removing the fan assembly module that comes with the Cisco uBR10012 universal broadband router. This document also includes technical specifications and troubleshooting information.

Contents

Feature Overview, page 2

Part Numbers and Technical Specifications, page 4

Safety Warnings, page 5

Removing and Replacing the Fan Assembly Module, page 9

Replacing the Fan Assembly Cable, page 11

Troubleshooting the Fan Assembly, page 13

Related Documentation, page 14

Obtaining Documentation, page 14

Obtaining Technical Assistance, page 16

Obtaining Additional Publications and Information, page 17

Feature Overview

The Cisco uBR10012 universal broadband router uses a fan assembly module (Figure 1 on page 3) containing four fans to supply cooling air to the chassis.

The fan assembly is located at the top of the chassis and is connected to the chassis with a blind mate connector that plugs into a cable assembly and then into the chassis backplane.

Four internal fans draw cooling air into the front of the chassis and direct it across the internal components to maintain an acceptable operating temperature. The air is exhausted through openings in the rear of the chassis.

The fan assembly module works at variable speeds:

Low speed (with a clean air filter): approximately 280 cubic feet per minute (cmf)

High speed (with a clean air filter): approximately 450 cmf

The operating speed is determined by the fan assembly module. If the temperature at the fan’s outlet gets to 40°C, then the blower starts to increase the speed of the fans. It does not reach high speed, however, until the temperature at the outlet reaches 50°C.

Three LEDs (System OK, Single Fan Failure, and Multi-Fan Failure) located on the front of the fan assembly indicate the status of the fans (see Table 1 on page 3).

Figure 1 on page 3 shows the fan assembly module.

Cisco uBR10012 Universal Broadband Router Fan Assembly Module

2

OL-5093-01

 

 

Figure 1 Fan Assembly Module

Fan assembly

CISCO

 

10000

CISCO

 

10000

56413

Table 1

Fan Assembly LEDs and Their Function

 

 

 

 

LED

 

Status

Description

 

 

 

 

System OK

 

Green

System is functioning normally; all fans are operating.

 

 

 

Single Fan Failure

Yellow

A single fan has failed; system triggers alarms, but the fan assembly

 

 

 

is still able to properly cool the chassis. Repair or replace the fan

 

 

 

assembly immediately.

 

 

 

Multi-Fan Failure

Yellow

Two or more fans have failed, and if the operating temperature

 

 

 

inside the chassis rises too high, the system automatically shuts

 

 

 

down. Repair or replace the fan assembly immediately.

 

 

 

 

Cisco uBR10012 Universal Broadband Router Fan Assembly Module

 

OL-5093-01

3

 

 

 

Part Numbers and Technical Specifications

Table 2 lists the specifications for the Cisco uBR10012 universal broadband router fan assembly module.

Table 2 Cisco uBR10012 Fan Assembly Module Specifications

Description

Specifications

 

 

Product number (fan assembly)

UBR10-FAN-ASSY=

 

 

Product number (cable)

UBR10-FAN-CAB=

 

 

Dimensions

Height: 5.60 in. (14.22 cm)

 

Width: 19 in. (482.26 cm)

 

Depth: 16.15 in. (41.02 cm)

 

 

Weight

30 lb (13.61 kg)

 

 

AC-input voltage and frequency

110 to 240 VAC, 50 to 60 Hz

 

 

Power consumption

250 Watts (4 amps, not to exceed 6 amps at startup)

 

 

Airflow

Low speed (with clean air filter): 280 cfm1

 

High speed (with clean air filter): 450 cfm

 

 

MTBF

Fans, 248,509 hours

 

Fan Control, 596,65 hours

 

 

Temperature range

Operating: 41 to 104°F (5 to 40°C)

 

Storage: –40 to 158°F (–40 to 70°C)

 

 

Relative humidity

Operating: 5 to 85%

 

Storage: 5 to 95%

 

 

Operating altitude

–197 to 13,123 ft (–60 to 4000 m)

 

 

1. Cubic feet per minute

Cisco uBR10012 Universal Broadband Router Fan Assembly Module

4

OL-5093-01

 

 

Safety Warnings

Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Cisco uBR10012 Universal Broadband Router Fan Assembly Module

 

OL-5093-01

5

 

 

 

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Cisco uBR10012 Universal Broadband Router Fan Assembly Module

6

OL-5093-01

 

 

Loading...
+ 12 hidden pages