Cisco Systems NPE-175, NPE-225 User Manual

0 (0)

Network Processing Engine and Network

Services Engine Installation and

Configuration

Product Number: NPE-100=, NPE-150=, NPE-175=, NPE-200=, NPE-225=, NPE-300=, NPE-400=, NSE-1=, NPE-G1=, UBR7200-NPE-G1=, NPE-G2=, UBR7200-NPE-G2=

See the product chapters for the platforms supported.

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 527-0883

Customer Order Number:

Text Part Number: OL-4448-12

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

This document is to be used in conjunction with the documents listed in the “Related Documentation” section of the Preface.

CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS,

Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0812R)

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Copyright © 1996–2008 Cisco Systems, Inc. All rights reserved.

 

C O N T E N T S

Preface i

 

Document Revision History i-i

Objectives

i-ii

Organization

i-ii

 

Related Documentation

i-iii

 

 

Obtaining Documentation and Submitting a Service Request

i-iv

 

NPE-100, NPE-150, and NPE-200 Overview 1-1

 

C H A P T E R 1

 

 

Supported Platforms 1-1

 

 

 

Software Requirements

1-1

 

 

NPE-100, NPE-150, and NPE-200 Description and Overview

1-1

 

 

 

Components

1-2

 

 

 

 

 

 

 

 

 

 

 

System Management Functions

1-5

 

 

 

 

 

 

 

Terms and Acronyms

1-5

 

 

 

 

 

 

 

 

 

NPE-100, NPE-150, and NPE-200 Memory Information 1-6

 

 

 

NPE-100 Memory Information

1-7

 

 

 

 

 

 

 

NPE-150 Memory Information

1-7

 

 

 

 

 

 

 

NPE-200 Memory Information

1-8

 

 

 

 

 

 

NPE-175 and NPE-225 Overview

 

 

 

 

 

 

C H A P T E R

2

2-1

 

 

 

 

 

 

 

 

Supported Platforms

2-1

 

 

 

 

 

 

 

 

 

 

Software Requirements

2-1

 

 

 

 

 

 

 

 

 

NPE-175 and NPE-225 Description and Overview

2-1

 

 

 

 

 

 

Components

2-2

 

 

 

 

 

 

 

 

 

 

 

System Management Functions

2-4

 

 

 

 

 

 

 

Terms and Acronyms

2-4

 

 

 

 

 

 

 

 

 

NPE-175 and NPE-225 Memory Information 2-5

 

 

 

 

 

 

NPE-300 and NPE-400 Overview

 

 

 

 

 

 

C H A P T E R

3

3-1

 

 

 

 

 

 

 

 

Supported Platforms

3-1

 

 

 

 

 

 

 

 

 

 

Software Requirements

3-1

 

 

 

 

 

 

 

 

 

NPE-300 and NPE-400 Description and Overview

3-2

 

 

 

 

 

 

Components

3-2

 

 

 

 

 

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

 

iii

 

 

 

 

 

 

 

 

 

 

 

Contents

 

 

System Management Functions

3-4

 

 

Terms and Acronyms

3-4

 

 

 

NPE-300 and NPE-400 Memory Information 3-5

 

 

NSE-1 Overview 4-1

 

 

 

C H A P T E R

4

 

 

 

 

 

Supported Platforms

4-1

 

 

 

 

Software Requirements

4-1

 

 

 

NSE-1 Description and Overview 4-1

 

 

Components

4-2

 

 

 

 

 

System Management Functions

4-3

 

 

Terms and Acronyms

4-3

 

 

 

NSE-1 Memory Information 4-4

 

 

 

NPE-G1 Overview

 

 

 

 

C H A P T E R

5

5-1

 

 

 

 

 

Supported Platforms

5-1

 

 

 

 

Software Requirements

5-1

 

 

 

NPE-G1 Description and Overview

5-2

 

 

Bandwidth

5-2

 

 

 

 

 

Components

5-3

 

 

 

 

 

Interfaces and LEDs

5-4

 

 

 

CompactFlash Disk

 

5-5

 

 

 

Summary of Important NPE-G1 Information 5-7

 

 

System Management Functions

5-8

 

 

Terms and Acronyms

5-8

 

NPE-G1 Memory Information 5-9

 

 

Connection Equipment and Specifications 5-10

 

 

Ethernet and Fast Ethernet RJ-45 Connection Equipment 5-10

Gigabit Ethernet GBIC Connection Equipment

5-13

Mode-Conditioning Patch Cord Description

5-16

Console and Auxiliary Port Connection Equipment

5-17

RJ-45

Console Port Signals and Pinouts

5-19

RJ-45

Auxiliary Port Signals and Pinouts

5-20

 

 

 

 

 

Fiber Optic Cleaning Information

5-20

 

 

 

NPE-G2 Overview 6-1

 

 

C H A P T E R 6

 

 

 

 

 

 

 

 

Supported Platforms 6-1

 

 

 

 

 

 

 

Software Requirements 6-2

 

 

 

 

 

 

 

NPE-G2 Description and Overview

6-2

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

iv

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

Contents

Bandwidth Requirements 6-3

Components

6-3

 

Interfaces

6-4

 

LEDs 6-5

 

 

CompactFlash Disk

6-6

USB Ports

6-8

 

Summary of Important NPE-G2 Information 6-9

System Management Functions 6-10

Terms and Acronyms

6-10

 

 

NPE-G2 Memory Information and Specifications

6-11

 

 

 

 

 

 

 

 

 

Connection Equipment and Specifications

6-13

 

 

 

 

 

 

 

 

 

Ethernet and Fast Ethernet RJ-45 Connection Equipment

6-13

 

 

 

 

 

 

 

Gigabit Ethernet SFP Connection Equipment

6-16

 

 

 

 

 

 

 

 

Mode-Conditioning Patch Cord Description

6-19

 

 

 

 

 

 

 

 

Console and Auxiliary Port Connection Equipment

6-20

 

 

 

 

 

 

 

 

RJ-45 Console Port Signals and Pinouts

6-22

 

 

 

 

 

 

 

 

RJ-45 Auxiliary Port Signals and Pinouts 6-23

 

 

 

 

 

 

 

 

Fiber Optic Cleaning Information

6-23

 

 

 

 

 

 

 

 

 

 

NPE-G1 and NPE-G2 Installation and Configuration Information

 

 

 

 

 

 

C H A P T E R 7

7-1

 

 

 

 

 

 

 

Preparing for an Upgrade 7-2

 

 

 

 

 

 

 

 

 

 

 

 

 

Copying the Configuration File

7-4

 

 

 

 

 

 

 

 

 

 

 

 

Copying the Configuration File to a Flash Disk or PC Card 7-4

 

 

 

 

 

 

 

Copying the Configuration File to a TFTP Server

7-5

 

 

 

 

 

 

 

 

Copying the Configuration File Using a PC

7-7

 

 

 

 

 

 

 

 

 

Removing the Network Processing Engine

7-7

 

 

 

 

 

 

 

 

 

 

Ensuring Easy Access to the Router

7-8

 

 

 

 

 

 

 

 

 

 

Powering Down the Router and Disconnecting Input Power

7-8

 

 

 

 

 

 

 

Powering Down the Router

7-8

 

 

 

 

 

 

 

 

 

 

 

Disconnecting AC-Input Power from a Cisco 7200 VXR Router

7-9

 

 

 

 

 

 

Disconnecting AC-Input Power from a Cisco uBR7246VXR Router

7-10

 

 

 

 

 

Disconnecting AC-Input Power from a Cisco uBR7225VXR Router

7-11

 

 

 

 

 

Disconnecting DC-Input Power from a Cisco 7200 VXR Router

7-11

 

 

 

 

 

Disconnecting DC-Input Power from a Cisco uBR7246VXR Router

7-13

 

 

 

 

 

Removing the NPE or NSE-1

7-16

 

 

 

 

 

 

 

 

 

 

 

Installing the NPE-G1 or NPE-G2

7-18

 

 

 

 

 

 

 

 

 

 

 

Basic Guidelines 7-18

 

 

 

 

 

 

 

 

 

 

 

 

 

Installing a CompactFlash Disk

7-19

 

 

 

 

 

 

 

 

 

 

 

Installing a USB Flash Memory Module or eToken—NPE-G2

7-19

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

 

 

 

v

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

 

 

 

Installing an SFP Module—NPE-G2

7-20

 

 

 

 

 

 

 

 

 

Installing a GBIC—NPE-G1

7-23

 

 

 

 

 

 

 

 

 

 

 

Replacing the DIMM on the NPE-G2

7-24

 

 

 

 

 

 

 

 

 

Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional)

7-26

 

 

 

 

 

 

 

Removing a SODIMM

7-26

 

 

 

 

 

 

 

 

 

 

 

Installing a SDRAM SODIMM

7-27

 

 

 

 

 

 

 

 

 

 

Inserting the NPE-G1 or NPE-G2 into the Router

7-28

 

 

 

 

 

 

 

 

Attaching the Rear Cable-Management Brackets and Cables (Optional)

7-29

 

 

 

 

 

Installing the NPE-G1 or NPE-G2 Cable-Management Brackets

7-29

 

 

 

 

 

Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional)

7-31

 

 

 

 

Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional)

7-32

 

 

 

 

Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router

 

 

 

 

 

(Optional)

7-34

 

 

 

 

 

 

 

 

 

 

 

 

Reconnecting Input Power and Powering Up the Router 7-35

 

 

 

 

 

 

 

 

Reconnecting AC-Input Power to the Cisco 7200 VXR Router

7-35

 

 

 

 

 

Reconnecting AC-Input Power to the Cisco uBR7246VXR Router

7-37

 

 

 

 

 

Reconnecting AC-Input Power to the Cisco uBR7225VXR Router

7-38

 

 

 

 

 

Reconnecting DC-Input Power to the Cisco 7200 VXR Router

7-38

 

 

 

 

 

Reconnecting DC-Input Power to a Cisco uBR7246VXR Router

7-41

 

 

 

 

 

Powering Up the Router

7-45

 

 

 

 

 

 

 

 

 

 

 

Enabling the Second Processor on the NPE-G1

7-46

 

 

 

 

 

 

 

 

Error Messages

7-47

 

 

 

 

 

 

 

 

 

 

 

 

Using show Commands Associated with the mpf Command

7-47

 

 

 

 

 

 

 

Using the show interface stats Command

7-48

 

 

 

 

 

 

 

 

Using the show ip interface Command 7-48

 

 

 

 

 

 

 

 

Using the show mpf cpu Command

7-49

 

 

 

 

 

 

 

 

 

Using the show mpf cpu history Command

7-49

 

 

 

 

 

 

 

 

Using the show mpf interface Command

7-50

 

 

 

 

 

 

 

 

Using the show mpf ip exact-route Command 7-51

 

 

 

 

 

 

 

 

Using the show mpf punt Command

7-51

 

 

 

 

 

 

 

 

 

Using the show version Command

7-51

 

 

 

 

 

 

 

 

 

Copying the Saved Configuration to NVRAM

7-52

 

 

 

 

 

 

 

 

 

Copying the Saved Configuration File from a Flash Disk or PC Card

7-53

 

 

 

 

 

Copying the Saved Configuration File from the CompactFlash Disk

7-53

 

 

 

 

 

Downloading the Saved Configuration from the TFTP Server

7-54

 

 

 

 

 

 

 

Auxiliary and Console Port Information

7-56

 

 

 

 

 

 

 

 

 

 

Configuring an Auxiliary Port to Receive Console Port Messages

7-56

 

 

 

 

 

 

Configuring the Native Gigabit Ethernet Interfaces

7-56

 

 

 

 

 

 

 

 

Changing the Media Type of the Native Gigabit Ethernet GBIC, SFP,

 

 

 

 

 

 

or RJ-45 Ports

7-56

 

 

 

 

 

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vi

 

 

 

 

 

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

 

 

 

 

 

7-58
7-57
7-57

Contents

Configuring the Interface Transmission and Speed Modes

Sample Configuration for the Gigabit Ethernet Interfaces

Debugging 7-58

Resetting the Interface

Clearing Counters 7-59

 

 

 

Using show Commands to Check the Installation

7-59

 

 

 

 

 

 

 

 

Upgrading the Cisco IOS Image and the Boot Helper (Boot Loader) Image

7-62

 

 

 

 

 

 

Upgrading ROMmon on the NPE-G1 or NPE-G2

7-63

 

 

 

 

 

 

 

 

Using the show rom-monitor Command and ROMmon CLI showmon Commands 7-64

 

 

 

 

Using the upgrade rom-monitor file Command 7-64

 

 

 

 

 

 

 

 

Changing Preferences to Choose the Other ROMmon Image

7-65

 

 

 

 

 

 

 

Troubleshooting the Upgrade

7-65

 

 

 

 

 

 

 

 

 

 

 

ROMmon Upgrade Error Messages

7-66

 

 

 

 

 

 

 

 

 

Upgrading FPGA on the NPE-G2

7-67

 

 

 

 

 

 

 

 

 

 

Troubleshooting the NPE-G1 or NPE-G2

7-67

 

 

 

 

 

 

 

 

 

Fiber Optic Cleaning Information

7-67

 

 

 

 

 

 

 

 

 

Preparation for Installation 8-1

 

 

 

 

 

 

 

 

 

C H A P T E R

8

 

 

 

 

 

 

 

 

 

 

 

 

Required Tools and Equipment

 

8-1

 

 

 

 

 

 

 

 

 

 

 

Software and Hardware Requirements

8-2

 

 

 

 

 

 

 

 

 

NPE or NSE Requirements

 

8-2

 

 

 

 

 

 

 

 

 

 

 

Port Adapter Jacket Card Support

8-4

 

 

 

 

 

 

 

 

 

Software Requirements

8-4

 

 

 

 

 

 

 

 

 

 

 

Safety Guidelines

8-8

 

 

 

 

 

 

 

 

 

 

 

 

 

Safety Warnings

8-9

 

 

 

 

 

 

 

 

 

 

 

 

 

Electrical Equipment Guidelines

8-14

 

 

 

 

 

 

 

 

 

Telephone Wiring Guidelines

8-14

 

 

 

 

 

 

 

 

 

 

Electrostatic Discharge Prevention

8-15

 

 

 

 

 

 

 

 

Removing and Installing the NPE or NSE

 

 

 

 

 

 

 

C H A P T E R

9

9-1

 

 

 

 

 

 

 

 

 

Ensuring Easy Access to the Router

9-1

 

 

 

 

 

 

 

 

 

 

Removing and Replacing the NPE or NSE

9-2

 

 

 

 

 

 

 

 

 

Powering Down the Router and Disconnecting Input Power

9-2

 

 

 

 

 

 

 

Powering Down the Router

9-3

 

 

 

 

 

 

 

 

 

Disconnecting AC-Input Power from a Cisco 7200 Series Router or Cisco 7200 VXR Router

9-4

 

 

 

Disconnecting AC-Input Power from a Cisco uBR7200 Series Router 9-4

 

 

 

 

Disconnecting DC-Input Power from a Cisco 7200 Series Router or Cisco 7200 VXR Router

9-5

 

 

 

Disconnecting DC-Input Power from a Cisco uBR7246 Router

9-7

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

 

 

 

vii

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

Removing the NPE or NSE

9-9

 

 

Removing and Installing Memory

9-11

 

Removing DRAM SIMMs

9-11

 

Installing DRAM SIMMs

9-13

 

 

Removing SDRAM DIMMs

9-14

 

Installing SDRAM DIMMs

9-16

 

Removing a SDRAM SODIMM

9-18

 

Installing a SDRAM SODIMM

9-19

 

Checking a SDRAM Upgrade or Replacement 9-20

 

Installing the NPE or NSE

9-21

 

 

Reconnecting Input Power and Powering Up the Router 9-23

 

Reconnecting AC-Input Power to the Cisco 7200 Series Router or Cisco 7200 VXR Router

9-25

Reconnecting AC-Input Power to the Cisco uBR7200 Series Router 9-26

 

Reconnecting DC-Input Power to a Cisco 7200 Series Router or Cisco 7200 VXR Router

9-27

Reconnecting DC-Input Power to a Cisco uBR7246VXR Router 9-29

 

Powering Up the Router

 

9-33

 

 

C H A P T E R 10

Configuration Tasks and Troubleshooting Information 10-1

 

 

 

 

 

 

NPE Configuration Tasks

10-1

 

 

 

 

 

 

 

NSE Configuration Tasks

10-1

 

 

 

 

 

 

 

Boot Changes in Cisco IOS Release 12.2

10-2

 

 

 

 

 

 

Troubleshooting the NPE-G1 or NPE-G2

10-2

 

 

 

 

 

 

.Troubleshooting the NPE-100 Through NPE-400 10-4

 

 

 

 

 

 

NPE or NSE show Commands 10-4

 

 

 

 

 

 

 

Using the show version Command

10-4

 

 

 

 

 

 

Using the show c7200 Command

10-5

 

 

 

 

 

 

Using the show environment Command with the NPE-G2—NPE-G2 -Specific Output 10-6

 

 

 

 

NSE-1 show Commands

10-6

 

 

 

 

 

 

 

Using the show pxf accounting ? Command and Subcommands 10-6

 

 

 

 

Using the show pxf crash Command

10-7

 

 

 

 

 

 

Using the show pxf info Command

10-8

 

 

 

 

 

 

Using the show pxf interface Command 10-9

 

 

 

 

 

 

Using the show pxf feature ? Command and Subcommands

10-9

 

 

 

 

 

NSE-1 Error Messages

10-10

 

 

 

 

 

 

 

Using Debugging Commands and PXF

10-11

 

 

 

 

 

 

PXF Troubleshooting Information 10-11

 

 

 

 

 

 

Removing and Replacing an AC-Input or DC-Input Power Supply

10-14

 

 

 

 

 

Removing a Power Supply from a Cisco 7200 Series Router

10-14

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

viii

 

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

 

Contents

Replacing a Power Supply in a Cisco 7200 Series Router 10-15

Fiber Optic Cleaning Information 10-17

I N D E X

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

ix

 

Contents

Network Processing Engine and Network Services Engine Installation and Configuration

 

x

OL-4448-12

 

 

 

Preface

This preface describes the objectives and organization of this document and explains how to find additional information on related products and services. This preface contains the following sections:

Document Revision History, page i

Objectives, page ii

Organization, page ii

Related Documentation, page iii

Obtaining Documentation and Submitting a Service Request, page iv

Document Revision History

The Document Revision History below records technical changes to this document.

Document

 

 

Revision Version

Date

Change Summary

 

 

 

OL-4448-12

December, 2008

Added information about Cisco uBR7225VXR support

 

 

on the NPE-G2.

 

 

 

OL-4448-11

June, 2008

Added information about the SFP-GE-F module.

 

 

 

OL-4448-10

February, 2008

Updated uBR7200-NPE-G2 support.

 

 

 

OL-4448-09

January, 2008

Added uBR7200-NPE-G2 support.

 

 

 

OL-4448-08

December, 2006

Added CWDM SFP module configuration information

 

 

for the NPE-G2.

 

 

 

OL-4448-07

September, 2006

Added the Port Adapter Jacket Card support information

 

 

for NPE-G1 and NPE-G2.

 

 

 

OL-4448-06

August, 2006

Added 2GB DIMM information for the NPE-G2.

 

 

 

OL-4448-05

May, 2006

AddedNPE-G2 information.

 

 

 

OL-4448-04

October, 2005

Added warning statement numbers and additional optical

 

 

cleaning document title and URL.

 

 

 

OL-4448-03

August 11, 2005

Added enabling the second CPU information as well as

 

 

show commands and output.

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

i

 

Preface

Objectives

Objectives

This document includes an overview of each network processing engine (NPE) or network services engine (NSE), instructions for removing and installing an NPE or NSE, steps for verifying that the installed NPE or NSE initializes the system after you power up the router, configuration instructions, and troubleshooting information.

The NPEs are supported in the following Cisco 7200 series routers and Cisco 7200 VXR routers:

Cisco 7200 series routers, consisting of the 2-slot Cisco 7202, 4-slot Cisco 7204 and Cisco 7204VXR, and the 6-slot Cisco 7206 and Cisco 7206VXR

Cisco 7206VXR as a router shelf in the AS5800 Universal Access Server

Note The NSE-1 is supported only in the Cisco 7204VXR and Cisco 7206VXR routers. The NPE-G1 is supported only in the Cisco 7204VXR, Cisco 7206VXR, and Cisco uBR7246VXR routers.

The NPEs are supported in the following Cisco uBR7200 series universal broadband routers:

Cisco uBR7223 (1 port adapter slot and 2 cable interface and line card slots)

Cisco uBR7246 (2 port adapter slots and 4 cable interface line card slots)

Cisco uBR7246VXR (2 port adapter slots, 4 cable interface line card slots, and 1 Cisco Cable Clock Card slot)

Cisco uBR7225VXR (2 cable interface line card slots)

Note See the individual product chapters for the specific platforms supported by the NPEs or NSE-1.

Organization

This document contains the following chapters:

:

 

 

 

 

Section

Title

Description

 

 

 

 

 

 

 

 

 

 

 

Chapter 1

NPE-100, NPE-150, and NPE-200

Describes the NPE-100, NPE-150, and

 

 

 

 

 

Overview

NPE-200—components, system management

 

 

 

 

 

 

functions, and memory specifications and

 

 

 

 

 

 

configuration.

 

 

 

 

 

 

 

 

 

 

 

Chapter 2

NPE-175 and NPE-225 Overview

Describes the NPE-175 and

 

 

 

 

 

 

NPE-225—components, system management

 

 

 

 

 

 

functions, and memory specifications and

 

 

 

 

 

 

configuration.

 

 

 

 

 

 

 

 

 

 

 

Chapter 3

NPE-300 and NPE-400 Overview

Describes the NPE-300 and

 

 

 

 

 

 

NPE-400—components, system management

 

 

 

 

 

 

functions, and memory specifications and

 

 

 

 

 

 

configuration.

 

 

 

 

 

 

 

 

 

 

 

Chapter 4

NSE-1 Overview

Describes the NSE-1—components, system

 

 

 

 

 

 

management functions, and memory

 

 

 

 

 

 

specifications and configuration.

 

 

 

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

ii

 

 

 

 

OL-4448-12

 

 

 

 

 

 

 

Preface

Related Documentation

Section

Title

Description

 

 

 

Chapter 5

NPE-G1 Overview

Describes the NPE-G1—components, system

 

 

management functions, and memory

 

 

specifications.

 

 

 

Chapter 6

NPE-G2 Overview

Describes the NPE-G2—components, system

 

 

management functions, and memory

 

 

specifications.

 

 

 

Chapter 7

NPE-G1 and NPE-G2 Installation

Provides installation and configuration

 

and Configuration Information

information for the NPE-G1 and NPE-G2.

 

 

 

Chapter 8

Preparation for Installation

Describes safety considerations, tools required,

 

 

and procedures you should perform before the

 

 

actual installation.

 

 

 

Chapter 9

Removing and Installing the NPE or

Describes the procedures for installing and

 

NSE

removing the network processing engine or

 

 

network services engine in the supported

 

 

platforms.

 

 

 

Chapter 10

Configuration Tasks and

Provides instructions for configuring the NSE-1

 

Troubleshooting Information

and troubleshooting information for both the

 

 

NPEs and NSE-1. It also provides power supply

 

 

removal information.

 

 

 

Related Documentation

Your router and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources:

Cisco IOS software:

For configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware.

Note You can access Cisco IOS software configuration and hardware installation and maintenance documentation on the World Wide Web at http://www.cisco.com. Translated documentation is available at http://www.cisco.com/public/countries_languages.shtml.

For the NPE-G1, see the NPE-G1 Read Me First document, which is available at the following URL: http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/ubr7246vxr/upgrade/guide/15066R.html

For the Cisco uBR7200-NPE-G1, see the Cisco uBR7200-NPE-G1 Read Me First document, which is available at the following URL:

http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/ubr7246vxr/upgrade/guide/15066R.html

For information on the Cisco 7200 series routers, refer to the following publications:

Your Cisco 7200 series routers contain extensive features and functionality, which are documented in the following resources:

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

iii

 

Preface

Obtaining Documentation and Submitting a Service Request

Cisco 7200 Series Routers Documentation Roadmap at http://www.cisco.com/en/US/docs/routers/7200/roadmaps/7200_series_doc_roadmap/3512.html for a list of all Cisco 7200 series routers documentation and troubleshooting tools and information.

Cisco 7200 Series Routers Port Adapter Documentation Roadmap at http://www.cisco.com/en/US/docs/routers/7200/roadmaps/7200_series_port_adapter_doc_roadma p/3530.html for a list of all Cisco 7200 series routers-supported port adapter documentation.

Cisco 7200 Series Routers Troubleshooting Documentation Roadmap at http://www.cisco.com/en/US/docs/routers/7200/roadmaps/7200_series_trblshoot_doc_roadmap/35 18.htmll for links to troubleshooting tools, utilities, and Tech Notes.

For information about the Cisco uBR7200 series routers, refer to the following publications:

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide at: http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/installation/guide/ub72khig.html

Cisco uBR7200 Series Configuration Notes at: http://www.cisco.com/en/US/products/hw/cable/ps2217/products_installation_and_configurati on_guides_list.html

For information about the Cisco AS5800 Universal Access Server, refer to the following publications:

Cisco AS5800 Universal Access Server Hardware Installation Guide at: http://www.cisco.com/en/US/docs/routers/access/as5800/hardware/installation/guide/5800_hi g.html

Cisco AS5800 Universal Access Server Regulatory Compliance and Safety Information at: http://www.cisco.com/en/US/products/hw/univgate/ps509/products_regulatory_approvals_and _compliance09186a00800c9843.html

To view Cisco documentation or obtain general information about the documentation, refer to the following sources:

“Obtaining Documentation and Submitting a Service Request” section on page iv

Cisco Information Packet that shipped with your router or switch

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Network Processing Engine and Network Services Engine Installation and Configuration

 

iv

OL-4448-12

 

 

 

C H A P T E R 1

NPE-100, NPE-150, and NPE-200 Overview

This chapter describes the network processing engine (NPE) models NPE-100, NPE-150, and NPE-200 and contains the following sections:

Supported Platforms, page 1-1

Software Requirements, page 1-1

NPE-100, NPE-150, and NPE-200 Description and Overview, page 1-1

NPE-100, NPE-150, and NPE-200 Memory Information, page 1-6

Supported Platforms

The following NPEs support the Cisco 7200 series routers and Cisco 7200 VXR routers:

NPE-100

NPE-150

NPE-200

The following NPEs support the Cisco uBR7246 and Cisco uBR7223 universal broadband routers:

NPE-150

NPE-200

The NPE-200 supports the Cisco 7206 as a router shelf in a Cisco AS5800 Universal Access Server.

Software Requirements

For minimum software release information, see the “Software Requirements” section on page 8-4.

NPE-100, NPE-150, and NPE-200 Description and Overview

This section contains information about the network processing engine components and the system management functions.

The network processing engine maintains and executes the system management functions for the Cisco 7200 series routers.

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

1-1

 

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Description and Overview

The network processing engine maintains and executes the system management functions for the Cisco uBR7200 series routers.

The NPE also shares the system memory and environmental monitoring functions with the I/O

controller.

 

 

 

Components

 

 

 

Figure 1-1

NPE-100

 

 

 

 

6

 

 

 

7

 

1

 

8

 

 

 

 

 

 

U12

 

 

 

9

 

2

 

U4

 

 

 

U25

10

 

 

 

 

 

U18

 

 

 

NETWORK PROCESSING ENGINE-100

66433

 

 

 

3

4

5

 

1

System controller

6

Midplane connectors

 

 

 

 

2

R4700 microprocessor

7

Temperature sensor

 

 

 

 

3

Captive installation screw

8

DRAM SIMMs

 

 

 

 

4

Handle

9

Bank 1

 

 

 

 

5

Temperature sensor

10

Bank 0

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

1-2

OL-4448-12

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Description and Overview

Figure 1-2

NPE-150

 

7

 

8

1

9

 

U12

 

10

2

U4

 

U25

3

11

 

U18

NETWORK PROCESSING ENGINE-150

66424

 

4

5

6

 

 

 

 

 

 

 

 

1

System controller

 

 

7

Midplane connectors

 

 

 

 

 

 

2

R4700 microprocessor

 

 

8

Temperature sensor

 

 

 

 

 

3

1-MB SRAM (U700 through U703 and

 

9

DRAM SIMMs

 

U800 through U803)

 

 

 

 

 

 

 

 

 

 

4

Captive installation screw

 

 

10

Bank 1

 

 

 

 

 

 

5

Handle

 

 

11

Bank 0

 

 

 

 

 

 

6

Temperature sensor

 

 

 

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

1-3

 

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Description and Overview

Figure 1-3

NPE-200

 

7

 

8

 

9

1

10

 

U52

 

11

2

U42

 

U25

3

12

 

U11

NETWORK PROCESSING ENGINE-200

66420

4

5

6

1

System controller

7

Midplane connectors

 

 

 

 

2

R5000 microprocessor

8

Temperature sensor

 

 

 

 

3

4-MB SRAM (U6, U10, U13, U14, U28, U29,

9

Boot ROM U92

 

U38, and U39)

 

 

 

 

 

 

4

Captive installation screw

10

DRAM SIMMs

 

 

 

 

5

Handle

11

Bank 1

 

 

 

 

6

Temperature sensor

12

Bank 0

 

 

 

 

The NPE-100, NPE-150, and NPE-200 consist of the following components:

Reduced instruction set computing (RISC) microprocessor

The NPE-100 and NPE-150 have an R4700 microprocessor that operates at an internal clock speed of 150 MHz.

The NPE-200 has an R5000 microprocessor that operates at an internal clock speed of 200 MHz.

System controller

The system controller provides hardware logic to interconnect the processor, DRAM, and the PCI-based system backplane bus. The NPE-150 and NPE-200 have a system controller that uses direct memory access (DMA) to transfer data between DRAM and packet SRAM on the network processing engine.

Network Processing Engine and Network Services Engine Installation and Configuration

1-4

OL-4448-12

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Description and Overview

Upgradable memory modules

The NPE-100, NPE-150, and NPE-200 use DRAM for storing routing tables, network accounting applications, packets of information in preparation for process switching, and packet buffering for SRAM overflow (except in the NPE-100, which contains no packet SRAM). The standard configuration is 32 MB, with up to 128 MB available through single in-line memory module (SIMM) upgrades.

Packet SRAM for storing data packets

The NPE-100 does not have packet SRAM.

The NPE-150 has 1 MB of SRAM.

The NPE-200 has 4 MB of SRAM.

Cache memory

The NPE-100, NPE-150, and NPE-200 have unified cache SRAM that functions as the secondary cache for the microprocessor. (The primary cache is within the microprocessor.)

Two environmental sensors for monitoring the cooling air as it leaves the chassis

Boot ROM for storing sufficient code for booting the Cisco IOS software on the NPE-200

Note The NPE-100 and NPE-150 use the boot ROM on the I/O controller.

System Management Functions

The network processing engines perform the following system management functions:

Sending and receiving routing protocol updates

Managing tables, caches, and buffers

Monitoring interface and environmental status

Providing Simple Network Management Protocol (SNMP) management through the console and Telnet interface

Accounting for and switching of data traffic

Booting and reloading images

Managing port adapters (including recognition and initialization during online insertion and removal)

Terms and Acronyms

Cache—Memory with fast access and small capacity used to temporarily store recently accessed data; found either incorporated into the processor or near it.

DIMM—dual in-line memory module

DRAM—dynamic random-access memory

Instruction and data cache—Instructions to the processor, and data on which the instructions work.

Integrated cache—Cache that is built into the processor; sometimes referred to as internal cache. Cache memory physically located outside the processor is not integrated, and is sometimes referred to as external cache.

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

1-5

 

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Memory Information

OTP—one time programmable

Primary, secondary, tertiary cache—Hierarchical cache memory storage based on the proximity of the cache to the core of the processor. Primary cache is closest to the processor core and has the fastest access. Secondary cache has slower access than primary cache, but faster access than tertiary cache.

RAM—random-access memory

RISC—reduced instruction set computing

ROM—read-only memory

SIMM—single in-line memory module

SDRAM—synchronous dynamic random-access memory

SDRAM-fixed—SDRAM of a fixed size or quantity; can be replaced, but not upgraded

SODIMM—small outline dual in-line memory module

SRAM—static random-access memory

Unified cache—Instruction cache and data cache are combined. For example, a processor may have primary cache with separate instruction and data cache memory, but unified secondary cache.

NPE-100, NPE-150, and NPE-200 Memory Information

To determine the memory configuration of your NPE, use the show version command.

The following example shows an NPE-150 installed in a Cisco 7206 router:

router(boot)# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-J-M), Released Version 11.1(17)CA Copyright (c) 1986-1999 by cisco Systems, Inc.

Compiled Sun 21-Apr-96 04:10

Image text-base:0x60010890, data-base:0x605F0000

(display text omitted)

cisco 7206 (NPE150) processor with 12288K/4096K bytes of memory. R4700 processor, Implementation 33, Rev 1.0, (Level 2 Cache) Last reset from power-on

(display text omitted)

Use the following sections for information about memory specifications and configurations for the NPE-100, NPE-150, and NPE-200.

Note To prevent DRAM errors in the NPE-100, NPE-150, or NPE-200, and to ensure that your system initializes correctly at startup, DRAM bank 0 (socket U18 and U25, or U11 and U25) must contain no fewer than two SIMMs of the same type. You may also install two SIMMs of the same type in bank 1 (socket U4 and U12, or U42 and U52); however, bank 0 must always contain the two largest SIMMs.

Network Processing Engine and Network Services Engine Installation and Configuration

1-6

OL-4448-12

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Memory Information

NPE-100 Memory Information

Table 1-1 provides information about memory specifications. Table 1-2 provides memory configurations for the NPE-100.

Table 1-1

NPE-100 Memory Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

Component Location on

Memory Type

 

Size

Quantity

Description

the NPE-100 Baord

 

 

 

 

 

 

DRAM

 

32 to 128 MB

2 to 4

16or 32-MB SIMMs (based on

Bank 0: U18 and U25

 

 

 

 

maximum DRAM required)

Bank 1: U4 and U12

 

 

 

 

 

 

Primary cache

 

R4700 processor, internal cache

U201

 

 

 

 

 

Secondary cache

512 KB

4

R4700 processor, unified, external cache

U2, U10, U14, and U26

 

 

 

 

 

 

Table 1-2

NPE-100 DRAM SIMM Configurations—Configurable Memory Only

 

 

 

 

 

 

 

Total DRAM1

Bank 0

Quantity - Bank 0

Bank 1

Quantity - Bank 1

Product Number

32 MB

U18 and U25

2 16-MB SIMMs2

U4 and U12

MEM-NPE-32MB2

64 MB

U18 and U25

2 32-MB SIMMs

U4 and U12

MEM-NPE-64MB2

128 MB

U18 and U25

2 32-MB SIMMs

U4 and U12

2 32-MB SIMMs

MEM-NPE-128MB2

1.Refer to the Cisco AS5800 Universal Access Server documentation listed in the “Related Documentation” section on page iii for Cisco AS5800 Universal Access Server DRAM options.

2.These products are also available as DRAM upgrades. For example, to upgrade a network processing engine from 32 MB to 64 MB of DRAM, order Product Number MEM-NPE-64MB=.

NPE-150 Memory Information

Table 1-3 provides information about memory specifications. Table 1-4 provides memory configurations for the NPE-150.

Table 1-3

NPE-150 Memory Specifications

 

 

 

 

 

 

 

 

 

 

 

 

Component Location on the

Memory Type

 

Size

Quantity

Description

NPE-150 Board

 

 

 

 

 

 

DRAM

 

32 to 128 MB

2 to 4

16or 32-MB SIMMs (based on maximum

Bank 0: U18 and U2

 

 

 

 

DRAM required)

Bank 1: U4 and U12

 

 

 

 

 

 

SRAM

 

1 MB

8

8 chips, each being 128K x 9 bits wide

U700 through U703

 

 

 

 

 

U800 through U803

 

 

 

 

 

 

Primary cache

 

R4700 processor, internal cache

U201

 

 

 

 

 

Secondary cache

512 MB

4

R4700 processor, unified, external cache

U2, U10, U14, and U26

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

1-7

 

 

 

Chapter 1 NPE-100, NPE-150, and NPE-200 Overview

NPE-100, NPE-150, and NPE-200 Memory Information

Table 1-4

NPE-150 DRAM SIMM Configurations—Configurable Memory Only

 

 

 

 

 

 

 

Total DRAM1

Bank 0

Quantity - Bank 0

Bank 1

Quantity - Bank 1

Product Number

32 MB

U18 and U25

2 16-MB SIMMs

U4 and U12

MEM-NPE-32 MB2

64 MB

U18 and U25

2 32-MB SIMMs

U4 and U12

MEM-NPE-64MB2

128 MB

U18 and U25

2 32-MB SIMMs

U4 and U12

2 32-MB SIMMs

MEM-NPE-128MB2

1.Refer to the Cisco AS5800 Universal Access Server documentation listed in the “Related Documentation” section on page iii for Cisco AS5800 Universal Access Server DRAM options.

2.These products are also available as DRAM upgrades. For example, to upgrade a network processing engine from 32 MB to 64 MB of DRAM, order Product Number MEM-NPE-64MB=.

NPE-200 Memory Information

Table 1-5 provides information about memory specifications. Table 1-6 provides memory configurations for the NPE-200.

Table 1-5

NPE-200 Memory Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

Component Location on the

Memory Type

 

Size

Quantity

Description

NPE-200 Board

 

 

 

 

 

 

DRAM

 

32 to 128 MB

2 to 4

16or 32-MB SIMMs (based on

Bank 0: U11 and U25

 

 

 

 

maximum DRAM required)

Bank 1: U42 and U52

 

 

 

 

 

 

SRAM

 

4 MB

8

8 chips, each being 512K x 8 bits wide

U6, U10, U13, U14, U28, U29,

 

 

 

 

 

U38, and U39

 

 

 

 

 

 

Boot ROM

 

256 KB

1

EPROM for the ROM monitor

U92

 

 

 

 

programs

 

 

 

 

 

 

 

Primary cache

 

R5000 processor, internal cache

U44

 

 

 

 

 

Secondary cache

512 KB

4

R5000 processor, unified, external

U16, U9, U109, and U107

 

 

 

 

cache

 

 

 

 

 

 

 

Table 1-6

NPE-200 DRAM SIMM Configurations—Configurable Memory Only

 

 

 

 

 

 

 

Total DRAM1

Bank 0

Quantity - Bank 0

Bank 1

Quantity - Bank 1

Product Number

32 MB

U11 and U25

2 16-MB SIMMs

U42 and U52

MEM-NPE-32MB2

64 MB

U11 and U25

2 32-MB SIMMs

U42 and U52

MEM-NPE-64MB2

128 MB

U11 and U25

2 32-MB SIMMs

U42 and U52

2 32-MB SIMMs

MEM-NPE-128MB2

1.Refer to the Cisco AS5800 Universal Access Server documentation listed in the “Related Documentation” section on page iii for Cisco AS5800 Universal Access Server DRAM options.

2.These products are also available as DRAM upgrades. For example, to upgrade a network processing engine from 32 MB to 64 MB of DRAM, order Product Number MEM-NPE-64MB=.

Network Processing Engine and Network Services Engine Installation and Configuration

1-8

OL-4448-12

 

 

C H A P T E R 2

NPE-175 and NPE-225 Overview

This chapter describes the network processing engine (NPE) models NPE-175 and NPE-225 and contains the following sections:

Supported Platforms, page 2-1

Software Requirements, page 2-1

NPE-175 and NPE-225 Description and Overview, page 2-1

NPE-175 and NPE-225 Memory Information, page 2-5

Supported Platforms

The following NPEs support the Cisco 7200 series routers and Cisco 7200 VXR routers:

NPE-175

NPE-225

The following NPEs support the Cisco uBR7246VXR universal broadband router, Cisco uBR7246, and Cisco uBR7223 universal broadband routers:

NPE-175

NPE-225

Software Requirements

For minimum software release information, see the “Software Requirements” section on page 8-4.

NPE-175 and NPE-225 Description and Overview

This section contains information about the network processing engine components and the system management functions. The network processing engine maintains and executes the system management functions for the Cisco 7200 series and Cisco uBR7200 series routers. The NPE also shares the system memory and environmental monitoring functions with the I/O controller.

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

2-1

 

 

 

Chapter 2 NPE-175 and NPE-225 Overview

NPE-175 and NPE-225 Description and Overview

Components

Figure 2-1

NPE-175

1

7

8

9

2

10

3

NETWORK PROCESSING ENGINE-150

66416

 

4

5

6

 

 

 

 

 

 

 

1

Network controller board

 

6

Handle

 

 

 

 

 

 

2

System controller

 

 

7

Midplane connectors

 

 

 

 

 

3

Processor engine board

 

8

Boot ROM (U1)

 

 

 

 

 

4

Captive installation screw

 

9

Temperature sensor

 

 

 

 

 

5

RM5270 microprocessor

 

10

SDRAM DIMM (U15)

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

2-2

OL-4448-12

 

 

Chapter 2 NPE-175 and NPE-225 Overview

NPE-175 and NPE-225 Description and Overview

Figure 2-2

NPE-225

1

7

8

9

2

10

3

NETWORK PROCESSING ENGINE-200

66417

 

4

5

6

 

 

 

 

 

 

 

1

Network controller board

 

6

Handle

 

 

 

 

 

 

2

System controller

 

 

7

Midplane connectors

 

 

 

 

 

3

Processor engine board

 

8

Boot ROM (U1)

 

 

 

 

 

4

Captive installation screw

 

9

Temperature sensor

 

 

 

 

 

5

RM5271 microprocessor

 

10

SDRAM DIMM (U15)

 

 

 

 

 

 

The NPE-175 and NPE-225 consist of the following components:

Reduced instruction set computing (RISC) microprocessor

The NPE-175 has an RM5270 microprocessor that operates at an internal clock speed of 200 MHz.

The NPE-225 has an RM5271 microprocessor that operates at an internal clock speed of 262 MHz.

System controller

The system controller provides hardware logic to interconnect the processor, DRAM, and the PCI-based system backplane bus. The NPE-175 and NPE-225 have one system controller that provides processor access to the two midplane and single I/O controller peripheral component interconnect (PCI) buses. The system controller also allows port adapters—on either of the two midplane PCI buses—access to SDRAM.

Upgradable memory modules

The NPE-175 and NPE-225 use SDRAM for providing code, data, and packet storage.

Cache memory

The NPE-175 and NPE-225 have unified cache SRAM that functions as the secondary cache for the microprocessor. (The primary cache is within the microprocessor.)

Two environmental sensors for monitoring the cooling air as it leaves the chassis

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

2-3

 

 

 

Chapter 2 NPE-175 and NPE-225 Overview

NPE-175 and NPE-225 Description and Overview

Boot ROM for storing sufficient code for booting the Cisco IOS software; the NPE-175 and NPE-225 have boot ROM

Note Neither the NPE-175 nor the NPE-225 has packet SRAM.

System Management Functions

The network processing engines perform the following system management functions:

Sending and receiving routing protocol updates

Managing tables, caches, and buffers

Monitoring interface and environmental status

Providing Simple Network Management Protocol (SNMP) management through the console and Telnet interface

Accounting for and switching of data traffic

Booting and reloading images

Managing port adapters (including recognition and initialization during online insertion and removal)

Terms and Acronyms

Cache—Memory with fast access and small capacity used to temporarily store recently accessed data; found either incorporated into the processor or near it.

DIMM—dual in-line memory module

DRAM—dynamic random-access memory

Instruction and data cache—Instructions to the processor, and data on which the instructions work.

Integrated cache—Cache that is built into the processor; sometimes referred to as internal cache. Cache memory physically located outside the processor is not integrated, and is sometimes referred to as external cache.

OTP—one time programmable

Primary, secondary, tertiary cache—Hierarchical cache memory storage based on the proximity of the cache to the core of the processor. Primary cache is closest to the processor core and has the fastest access. Secondary cache has slower access than primary cache, but faster access than tertiary cache.

RAM—random-access memory

RISC—reduced instruction set computing

ROM—read-only memory

SIMM—single in-line memory module

SDRAM—synchronous dynamic random-access memory

SDRAM-fixed—SDRAM of a fixed size or quantity; can be replaced, but not upgraded

SODIMM—small outline dual in-line memory module

Network Processing Engine and Network Services Engine Installation and Configuration

2-4

OL-4448-12

 

 

Chapter 2 NPE-175 and NPE-225 Overview

NPE-175 and NPE-225 Memory Information

SRAM—static random-access memory

Unified cache— Instruction cache and data cache are combined. For example, a processor may have primary cache with separate instruction and data cache memory, but unified secondary cache.

NPE-175 and NPE-225 Memory Information

To determine the memory configuration of your NPE, use the show version command.

The following example shows an NPE-225 installed in a Cisco 7206VXR router:

router(boot)# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-BOOT-M), Released Version 12.0(19990124:222541) [biff-nightly 115]

Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 15-Feb-99 21:50 by biff

Image text-base:0x600088F8, data-base:0x6064C000

(display text omitted)

cisco 7206VXR (NPE225) processor with 57344K/8192K bytes of memory. R527x CPU at 262Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache

6 slot VXR midplane, Version 2.0

(display text omitted)

Table 2-1 provides memory specifications, Table 2-2 provides memory configurations for the NPE-175, and Table 2-3 provides memory configurations for the NPE-225.

Table 2-1

NPE-175 and NPE-225 Memory Specifications

 

 

 

 

 

 

 

 

 

 

 

 

Component

 

 

 

 

 

Location on the

 

 

 

 

 

NPE-175 and

Memory Type

 

Size

Quantity

Description

NPE-225 Board

 

 

 

 

 

 

SDRAM

 

64 or 128 MB

1 configurable

DIMM

U15

 

 

 

bank with 1

 

 

 

 

 

SDRAM slot

 

 

 

 

 

 

 

 

Boot ROM

 

512 KB

1

OTP ROM for the ROM monitor

U1

 

 

 

 

program

 

 

 

 

 

 

 

Primary cache

 

16 KB (instruction),

RM5270 processor, primary internal

U4

 

 

16 KB (data)

 

cache

 

 

 

 

 

 

 

 

 

32 KB (instruction),

RM5271 processor, primary internal

U4

 

 

32 KB (data)

 

cache

 

 

 

 

 

 

Secondary cache

2 MB

4 x 256 x 18 bits =

RM527x processor, unified external

U5, U6, U7, U81

 

 

 

64 bit plus 4 parity

cache

 

 

 

 

bits

 

 

 

 

 

 

 

 

1. Located on the processor engine board.

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

2-5

 

 

 

Chapter 2 NPE-175 and NPE-225 Overview

NPE-175 and NPE-225 Memory Information

Table 2-2 NPE-175 SDRAM DIMM Configurations—Configurable Memory Only

Total SDRAM

Bank

Quantity

Product Number

 

 

 

 

64 MB

U15

1 64-MB DIMM

MEM-SD-NPE-64MB

 

 

 

 

128 MB

U15

1 128-MB DIMM

MEM-SD-NPE-128MB

 

 

 

 

Table 2-3

NPE-225 SDRAM DIMM Configurations—Configurable Memory Only

 

 

 

 

 

 

Total SDRAM

 

Bank

Quantity

Product Number

 

 

 

 

 

64 MB

 

U15

1 64-MB DIMM

MEM-SD-NPE-64MB

 

 

 

 

 

128 MB

 

U15

1 128-MB DIMM

MEM-SD-NPE-128MB

 

 

 

 

 

256 MB

 

U15

1 256-MB DIMM

MEM-SD-NSE-256MB

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

2-6

OL-4448-12

 

 

C H A P T E R 3

NPE-300 and NPE-400 Overview

This chapter describes the network processing engine (NPE) models NPE-300 and NPE-400 and contains the following sections:

Supported Platforms, page 3-1

Software Requirements, page 3-1

NPE-300 and NPE-400 Description and Overview, page 3-2

NPE-300 and NPE-400 Memory Information, page 3-5

Supported Platforms

The following NPEs support the Cisco 7200 VXR routers:

NPE-300

NPE-400

The following NPEs support the Cisco uBR7246VXR universal broadband router:

NPE-300

NPE-400

The following NPEs support the Cisco 7206VXR as a router shelf in the Cisco AS5800 Universal Access Router:

NPE-300

NPE-400

These NPEs are keyed to prevent insertion in the Cisco 7200 series routers (7202, 7204, 7206).

Software Requirements

For minimum software release information, see the “Software Requirements” section on page 8-4.

Network Processing Engine and Network Services Engine Installation and Configuration

 

OL-4448-12

3-1

 

 

 

Cisco Systems NPE-175, NPE-225 User Manual

Chapter 3 NPE-300 and NPE-400 Overview

NPE-300 and NPE-400 Description and Overview

NPE-300 and NPE-400 Description and Overview

This section contains information about the network processing engine components and the system management functions. The network processing engine maintains and executes the system management functions for the routers. It also shares the system memory and environmental monitoring functions with the I/O controller.

Components

Figure 3-1

NPE-300

1

2

3

4

5

NETWORK PROCESSING ENGINE-300

11

12

13

14

15

16

66410

 

6

7

8

9

10

 

 

 

 

 

 

 

 

 

1

Midplane connectors

 

 

 

 

9

RM7000 microprocessor

 

 

 

 

 

 

 

 

2

Keying post

 

 

 

 

10

Temperature sensor (U42)

 

 

 

 

 

 

 

 

3

DIMM 3 (U44)

 

 

 

 

11

Keying post

 

 

 

 

 

 

 

 

4

Bank 1 (user configurable)

 

 

 

 

12

Temperature sensor (U41)

 

 

 

 

 

 

 

 

5

DIMM 2 (U45)

 

 

 

 

13

Boot ROM (U1)

 

 

 

 

 

 

 

 

6

Captive installation screw

 

 

 

 

14

DIMM 0 (U16)

 

 

 

 

 

 

 

 

7

Handle

 

 

 

 

15

Bank 0 (fixed)

 

 

 

 

 

 

 

 

8

System controllers

 

 

 

 

16

U15 (never populated)

 

 

 

 

 

 

 

 

Network Processing Engine and Network Services Engine Installation and Configuration

3-2

OL-4448-12

 

 

Loading...
+ 196 hidden pages