Loading...
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Cisco Nexus 5000 Series Hardware
Installation Guide
For the Cisco Nexus 5000 Platform Switches and the Cisco Nexus 5500 Platform Switches
March, 2013
Americas Headquarters
Cisco Systems, Inc. 170 West Tasman Drive
San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
800 553-NETS (6387) Fax: 408 527-0883
Text Part Number: OL-15902-02
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
•Turn the television or radio antenna until the interference stops.
•Move the equipment to one side or the other of the television or radio.
•Move the equipment farther away from the television or radio.
•Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Cisco Nexus 5500 Platform and 5000 Platform Hardware Installation Guide
© 2008-2011 Cisco Systems, Inc. All rights reserved.
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
|
C O N T E N T S |
iii |
|
Preface ix |
|
Audience ix |
|
Organization |
ix |
Conventions |
x |
Related Documentation xvi |
|
|
|
Release Notes |
xvi |
|
|
|
|
|
|
||
|
|
Configuration Guides |
xvi |
|
|
|
|
|
|||
|
|
Maintain and Operate Guides |
xvi |
||||||||
|
|
Installation and Upgrade Guides |
xvi |
||||||||
|
|
Licensing Guide |
xvii |
|
|
|
|
|
|
||
|
|
Command References |
xvii |
|
|
|
|
|
|||
|
|
Technical References |
xvii |
|
|
|
|
|
|||
|
|
Error and System Messages |
xvii |
|
|
|
|
||||
|
|
Troubleshooting Guide |
xvii |
|
|
|
|
|
|||
|
|
Obtaining Documentation and Submitting a Service Request xvii |
|||||||||
|
Overview 1-1 |
|
|
|
|
|
|
|
|
|
|
C H A P T E R 1 |
|
|
|
|
|
|
|
|
|
||
|
|
Cisco Nexus 5500 Platform Switches |
1-1 |
|
|
|
|||||
|
|
Cisco Nexus 5596UP Switch |
1-2 |
|
|
|
|
||||
|
|
Features |
1-2 |
|
|
|
|
|
|
||
|
|
Chassis |
|
1-2 |
|
|
|
|
|
|
|
|
|
Expansion Modules |
1-4 |
|
|
|
|
||||
|
|
Ports |
1-7 |
|
|
|
|
|
|
|
|
|
|
Power Supply |
1-8 |
|
|
|
|
|
|
||
|
|
Fan Module |
1-10 |
|
|
|
|
|
|
||
|
|
Transceivers |
1-11 |
|
|
|
|
|
|
||
|
|
Cisco Nexus 5596T Switch |
1-12 |
|
|
|
|
||||
|
|
Features |
1-13 |
|
|
|
|
|
|
||
|
|
Chassis |
|
1-13 |
|
|
|
|
|
|
|
|
|
Expansion Modules |
1-15 |
|
|
|
|
||||
|
|
Ports |
1-15 |
|
|
|
|
|
|
|
|
|
|
Power Supply |
1-16 |
|
|
|
|
|
|||
|
|
Fan Module |
1-16 |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
OL-15902-02 |
|
|
|
|
|
|
|
|
iii |
|
|
|
|
|
|
|
|
|
|
|
||
Contents
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
|
|
|
|
|
Transceivers |
|
1-16 |
|
|
|
|
||
|
|
|
|
|
Cisco Nexus 5548UP and 5548P Switches 1-17 |
||||||||
|
|
|
|
|
Features |
1-18 |
|
|
|
|
|
||
|
|
|
|
|
Chassis |
|
1-18 |
|
|
|
|
|
|
|
|
|
|
|
Expansion Modules |
1-20 |
|
|
|
||||
|
|
|
|
|
Data Ports |
|
1-23 |
|
|
|
|
||
|
|
|
|
|
Power Supplies |
1-23 |
|
|
|
||||
|
|
|
|
|
Fan Modules |
|
1-25 |
|
|
|
|
||
|
|
|
|
|
Transceivers and Cables 1-26 |
|
|
|
|||||
|
|
|
|
|
Cisco Nexus 5000 Platform Switches 1-29 |
|
|
|
|||||
|
|
|
|
|
Cisco Nexus 5020 Switch |
1-29 |
|
|
|
||||
|
|
|
|
|
Features |
1-29 |
|
|
|
|
|
||
|
|
|
|
|
Chassis |
|
1-30 |
|
|
|
|
|
|
|
|
|
|
|
Expansion Modules |
1-32 |
|
|
|
||||
|
|
|
|
|
Ports |
1-35 |
|
|
|
|
|
|
|
|
|
|
|
|
Power Supply |
1-37 |
|
|
|
|
|||
|
|
|
|
|
Fan Modules |
|
1-38 |
|
|
|
|
||
|
|
|
|
|
Transceivers |
|
1-39 |
|
|
|
|
||
|
|
|
|
|
Cisco Nexus 5010 Switch |
1-40 |
|
|
|
||||
|
|
|
|
|
Features |
1-40 |
|
|
|
|
|
||
|
|
|
|
|
Chassis |
|
1-41 |
|
|
|
|
|
|
|
|
|
|
|
Expansion Modules |
1-42 |
|
|
|
||||
|
|
|
|
|
Ports |
1-47 |
|
|
|
|
|
|
|
|
|
|
|
|
Power Supplies |
1-48 |
|
|
|
||||
|
|
|
|
|
Fan Modules |
|
1-49 |
|
|
|
|
||
|
|
|
|
|
Transceivers |
|
1-50 |
|
|
|
|
||
|
|
Installing the Cisco Nexus 5000 Series Switches |
|
|
|||||||||
C H A P T E R 2 |
|
2-1 |
|
||||||||||
|
|
|
|
|
Preparing for Installation |
2-2 |
|
|
|
||||
|
|
|
|
|
Installation Options with Racks and Cabinets |
2-2 |
|
||||||
|
|
|
|
|
Airflow Direction |
2-2 |
|
|
|
|
|||
|
|
|
|
|
Chassis Weight |
2-2 |
|
|
|
|
|||
|
|
|
|
|
Installation Guidelines |
2-3 |
|
|
|
||||
|
|
|
|
|
Required Equipment |
2-4 |
|
|
|
||||
|
|
|
|
|
Unpacking and Inspecting the Switch |
2-4 |
|
|
|||||
|
|
|
|
|
Installing the Switch |
2-5 |
|
|
|
|
|||
|
|
|
|
|
Installing a Cisco Nexus 5596 Switch |
2-5 |
|
|
|||||
|
|
|
|
|
Installing the Cisco Nexus 5548 Switch |
2-9 |
|
|
|||||
|
|
|
|
|
Installing the Cisco Nexus 5020 Switch |
2-11 |
|
|
|||||
|
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
||||||
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
iv |
|
|
|
|
|
|
|
|
|
|
OL-15902-02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
Contents
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
|
Installing the Cisco Nexus 5010 Switch |
2-15 |
|
|||||
|
Grounding the Switch |
2-17 |
|
|
|
|
|
|
|
Proper Grounding Practices |
2-17 |
|
|
|
|
||
|
Preventing Electrostatic Discharge Damage |
2-19 |
||||||
|
Establishing the System Ground |
2-21 |
|
|
|
|||
|
Required Tools and Equipment |
2-21 |
|
|
|
|||
|
Grounding the Cisco Nexus 5500 Series Chassis |
2-22 |
||||||
|
Grounding the Cisco Nexus 5000 Series Chassis |
2-24 |
||||||
|
Starting the Switch |
2-25 |
|
|
|
|
|
|
|
Connecting the Switch |
|
|
|
|
|
|
|
C H A P T E R 3 |
3-1 |
|
|
|
|
|
|
|
|
Preparing for Network Connections |
3-2 |
|
|
|
|
||
|
Connecting to the Console Port |
3-2 |
|
|
|
|
|
|
|
Connecting to the Ethernet Connector Port |
3-3 |
|
|
||||
|
Connecting to an Ethernet Port |
3-4 |
|
|
|
|
|
|
|
Installing and Replacing SFP+ Transceivers |
3-4 |
|
|||||
|
Installing an SFP+ Transceiver |
3-4 |
|
|
|
|||
|
Replacing an SFP+ Transceiver |
3-5 |
|
|
||||
|
Installing Cables into SFP+ Transceivers |
3-6 |
|
|||||
|
Installing a Cable into an SFP+ Transceiver |
3-6 |
||||||
|
Replacing a Cable for an SFP+ Transceiver |
3-7 |
||||||
|
Connecting to a Fibre Channel Port |
3-7 |
|
|
|
|
||
|
Removing and Installing SFP Transceivers |
3-8 |
|
|||||
|
Installing an SFP Transceiver |
3-8 |
|
|
|
|||
|
Removing an SFP Transceiver |
3-8 |
|
|
|
|||
|
|
Removing and Installing Cables into SFP Transceivers |
3-10 |
|
|
|
|
||
|
|
Installing a Cable into an SFP Transceiver |
3-10 |
|
|
|
|
|
|
|
|
Removing a Cable from an SFP Transceiver |
3-11 |
|
|
|
|
|
|
|
|
Maintaining SFP Transceivers and Fiber-Optic Cables |
3-11 |
|
|
|
|
||
|
Replacing Components 4-1 |
|
|
|
|
|
|
|
|
C H A P T E R 4 |
|
|
|
|
|
|
|
||
|
|
Replacing an I/O Module for a Cisco Nexus 5548 Switch |
4-1 |
|
|
|
|
||
|
|
Removing an I/O Module |
4-2 |
|
|
|
|
|
|
|
|
Installing an I/O Module |
4-4 |
|
|
|
|
|
|
|
|
Replacing Expansion Modules |
4-5 |
|
|
|
|
|
|
|
|
Removing an Expansion Module from a Cisco Nexus 5500 Platform Chassis |
4-5 |
|
|
|
|||
|
|
Installing an Expansion Module in a Cisco Nexus 5500 Platform Chassis 4-5 |
|
|
|
|
|||
|
|
Removing an Expansion Module from a Cisco Nexus 5000 Platform Chassis |
4-6 |
|
|
|
|||
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
|||
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
OL-15902-02 |
|
|
|
|
|
|
v |
|
|
|
|
|
|
|
|
|
||
Contents
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
|
|
|
|
Installing an Expansion Module in the Cisco Nexus 5000 Platform Chassis 4-7 |
|
|
|||||||
|
|
|
|
Replacing or Installing Power Supplies 4-8 |
|
|
|
|
|||||
|
|
|
|
Removing a Power Supply |
4-9 |
|
|
|
|
||||
|
|
|
|
Installing a Power Supply |
4-11 |
|
|
|
|
||||
|
|
|
|
Wiring a DC Power Connector |
4-12 |
|
|
|
|
||||
|
|
|
|
Replacing a Fan Module |
|
4-13 |
|
|
|
|
|
|
|
|
|
|
|
Removing a Fan Module |
4-14 |
|
|
|
|
|
|||
|
|
|
|
Installing a Fan Module |
4-14 |
|
|
|
|
|
|||
|
|
|
|
Removing the Cisco Nexus 5500 Platform Chassis or the Cisco Nexus 5000 Platform Chassis |
4-17 |
|
|||||||
|
|
|
|
Repacking Cisco Nexus 5500 Platform Switch Components or Cisco Nexus 5000 Platform Switch |
|||||||||
|
|
|
|
Components for Return Shipment |
4-17 |
|
|
|
|
||||
|
|
Cabinet and Rack Installation |
|
|
|
|
|
|
|||||
A P P E N D I X |
A |
A-1 |
|
|
|
|
|
||||||
|
|
|
|
Cabinet and Rack Requirements A-1 |
|
|
|
|
|||||
|
|
|
|
General Requirements for Cabinets and Racks |
A-1 |
|
|
|
|||||
|
|
|
|
Requirements Specific to Perforated Cabinets |
A-2 |
|
|
|
|||||
|
|
|
|
Cable Management Guidelines |
A-2 |
|
|
|
|
||||
|
|
Technical Specifications |
|
|
|
|
|
|
|
|
|||
A P P E N D I X |
B |
|
B-1 |
|
|
|
|
|
|
||||
|
|
|
|
Switch Specifications |
B-1 |
|
|
|
|
|
|
||
|
|
|
|
Environmental Specifications |
B-2 |
|
|
|
|
|
|||
|
|
|
|
Expansion Module Specifications |
B-3 |
|
|
|
|
||||
|
|
|
|
Power Specifications |
B-3 |
|
|
|
|
|
|
||
|
|
|
|
Specifications for the Cisco Nexus 5596 Power Supply |
B-3 |
|
|
||||||
|
|
|
|
Specifications for the Cisco Nexus 5548 Power Supply |
B-4 |
|
|
||||||
|
|
|
|
Specifications for the Cisco Nexus 5020 Power Supplies |
B-5 |
|
|
||||||
|
|
|
|
Specifications for the Cisco Nexus 5010 Power Supply |
B-5 |
|
|
||||||
|
|
|
|
Transceiver Specifications |
B-6 |
|
|
|
|
|
|||
|
|
|
|
Environmental Conditions and Power Requirement Specifications for SFP+ Transceivers |
B-6 |
||||||||
|
|
|
|
General Specifications for Cisco Fibre Channel SFP Transceivers B-7 |
|
|
|||||||
|
|
|
|
Environmental Conditions and Power Requirements Specification for SFP Transceivers |
B-7 |
||||||||
|
|
Cable and Port Specifications |
|
|
|
|
|
|
|||||
A P P E N D I X |
C |
C-1 |
|
|
|
|
|
||||||
|
|
|
|
Console Cable |
C-1 |
|
|
|
|
|
|
|
|
|
|
|
|
Cable RJ-45 Connector Pinouts |
C-2 |
|
|
|
|
||||
|
|
|
|
Console Port |
C-2 |
|
|
|
|
|
|
|
|
|
|
|
|
Console Port Pinouts |
C-2 |
|
|
|
|
|
|||
|
|
|
|
Supported Power Cords and Plugs |
C-3 |
|
|
|
|
||||
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
vi |
|
|
|
|
|
|
|
|
|
|
OL-15902-02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
Contents
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Jumper Power Cord C-9
A P P E N D I X |
D |
LEDs D-1 |
|
|
|
|
|
|
|
|
|
Chassis and Module LEDs for the Cisco Nexus 5000 Series Switches |
D-1 |
||||||
|
|
Chassis and Module LED Descriptions |
D-2 |
|
|
||||
|
|
Conditions Indicated by the Power Supply LEDs |
D-3 |
|
|||||
|
|
Port LEDs |
D-4 |
|
|
|
|
|
|
|
|
Ethernet Port LEDs |
D-4 |
|
|
|
|
|
|
|
|
Ethernet and Fibre Channel LEDs |
D-4 |
|
|
||||
|
|
Troubleshooting Hardware Components |
|
|
|
||||
A P P E N D I X |
E |
E-1 |
|
|
|||||
|
|
Overview |
E-1 |
|
|
|
|
|
|
|
|
SNMP Traps E-1 |
|
|
|
|
|
|
|
|
|
Switch Hardware Best Practices |
E-2 |
|
|
|
|
||
|
|
Installation Best Practices |
E-2 |
|
|
|
|
||
|
|
Initialization Best Practices |
E-2 |
|
|
|
|
||
|
|
Switch Operation Best Practices |
E-2 |
|
|
||||
|
|
Power Supply Conditions |
E-2 |
|
|
|
|
|
|
|
|
Accessory Kits |
|
|
|
|
|
|
|
A P P E N D I X |
F |
F-1 |
|
|
|
|
|
|
|
|
|
Cisco Nexus 5596UP and 5596T Switch Accessory Kit |
F-1 |
|
|||||
|
|
Cisco Nexus 5548UP and Cisco Nexus 5548P Switch Accessory Kit |
F-1 |
||||||
|
|
Cisco Nexus 5020 Switch Accessory Kit |
|
F-2 |
|
|
|||
|
|
Cisco Nexus 5010 Switch Accessory Kit |
|
F-2 |
|
|
|||
|
|
Site Planning and Maintenance Records |
|
|
|
||||
A P P E N D I X |
G |
G-1 |
|
|
|||||
|
|
Site Preparation Checklist |
G-1 |
|
|
|
|
|
|
|
|
Contact and Site Information G-3 |
|
|
|
|
|||
|
|
Chassis and Module Information |
G-4 |
|
|
|
|
||
I N D E X
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-02 |
vii |
|
Contents
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Cisco Nexus 5000 Series Hardware Installation Guide
|
viii |
OL-15902-02 |
|
|
|
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Preface
This preface describes the audience, organization, and conventions of the Cisco Nexus 5000 Series Hardware Installation Guide. It also provides information on how to obtain related documentation.
Audience
To use this installation guide, you must be familiar with electronic circuitry and wiring practices and preferably be an electronic or electromechanical technician.
Organization
This guide is organized as follows:
|
|
Chapter and Title |
Description |
|
|||
|
|
|
|
|
|||
|
|
Chapter 1, “Overview” |
Provides an overview of the Cisco Nexus 5000 Platform switches |
||||
|
|
|
and the Cisco Nexus 5500 Platform switches. |
||||
|
|
|
|
|
|||
|
|
Chapter 2, “Installing the Cisco |
Describes how to install the Cisco Nexus 5000 Platform switches |
||||
|
|
Nexus 5000 Series Switches” |
and the Cisco Nexus 5000 Platform switches, and how to install |
||||
|
|
|
modules, power supplies, and fan assemblies. |
||||
|
|
|
|
|
|||
|
|
Chapter 4, “Connecting the |
Describes how to connect the Cisco Nexus 5000 Series switches |
||||
|
|
Switch” |
to the Internet |
||||
|
|
|
|
|
|||
|
|
Appendix A, “Cabinet and Rack |
Provides guidelines for selecting an enclosed cabinet, the |
||||
|
|
Installation” |
procedure for installing a switch using the optional and EIA Shelf |
||||
|
|
|
Bracket Kit. |
||||
|
|
|
|
|
|||
|
|
Appendix B, “Technical |
Lists specifications for the Cisco Nexus 5500 Platform switches |
||||
|
|
Specifications” |
and the Cisco Nexus 5000 Platform switches and components |
||||
|
|
|
including modules, power supplies, and transceivers. |
||||
|
|
|
|
|
|||
|
|
Appendix C, “Cable and Port |
Lists cable and port specifications for the Cisco Nexus 5500 |
||||
|
|
Specifications” |
Platform switches and the Cisco Nexus 5000 Platform switches. |
||||
|
|
|
|
|
|||
|
|
Appendix D, “Site Planning and |
Provides site planning and maintenance records. |
||||
|
|
Maintenance Records” |
|
|
|
|
|
|
|
|
|
|
|||
|
|
Appendix E, “Troubleshooting |
Provides installation troubleshooting information for the Cisco |
||||
|
|
Hardware Components” |
Nexus 5500 Platform switches and the Cisco Nexus 5000 |
||||
|
|
|
Platform switches. |
||||
|
|
|
|
|
|
|
|
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
OL-15902-02 |
|
|
ix |
|
||
|
|
|
|
||||
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Conventions
This document uses the following conventions for notes, cautions, and safety warnings.
Notes and Cautions contain important information that you should be aware of.
Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered in the publication.
Caution Means reader be careful. You are capable of doing something that might result in equipment damage or loss of data.
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, can cause physical injuries. A warning symbol precedes each warning statement.
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Cisco Nexus 5000 Series Hardware Installation Guide
|
x |
OL-15902-02 |
|
|
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-02 |
xi |
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning! VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
SPARA DESSA ANVISNINGAR
Cisco Nexus 5000 Series Hardware Installation Guide
|
xii |
OL-15902-02 |
|
|
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-02 |
xiii |
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Cisco Nexus 5000 Series Hardware Installation Guide
|
xiv |
OL-15902-02 |
|
|
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-02 |
xv |
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Related Documentation
Documentation for Cisco MDS 9200 Series Switches and Cisco Nexus 2000 Series Fabric Extenders is available at the following URL:
http://www.cisco.com/en/US/products/ps9670/tsd_products_support_series_home.html
The following are related Cisco MDS 9200 Series and Cisco Nexus 2000 Series Fabric Extender documents:
Release Notes
Cisco Nexus 5000 Series and Cisco Nexus 2000 Series Release Notes
Cisco Nexus 5000 Series Switch Release Notes
Configuration Guides
Cisco Nexus 5000 Series Configuration Limits for Cisco NX-OS Release 5.0(2)N1(1)
Cisco Nexus 5000 Series Configuration Limits for Cisco NX-OS Release 4.2(1)N1(1) and Release 4.2(1)N2(1)
Cisco Nexus 5000 Series NX-OS Fibre Channel over Ethernet Configuration Guide
Cisco Nexus 5000 Series NX-OS Layer 2 Switching Configuration Guide
Cisco Nexus 5000 Series NX-OS Multicast Routing Configuration Guide
Cisco Nexus 5000 Series NX-OS Quality of Service Configuration Guide
Cisco Nexus 5000 Series NX-OS SAN Switching Configuration Guide
Cisco Nexus 5000 Series NX-OS Security Configuration Guide
Cisco Nexus 5000 Series NX-OS System Management Configuration Guide
Cisco Nexus 5000 Series NX-OS Unicast Routing Configuration Guide
Cisco Nexus 5000 Series Switch NX-OS Software Configuration Guide
Cisco Nexus 5000 Series Fabric Manager Configuration Guide, Release 3.4(1a)
Cisco Nexus 7000 Series NX-OS Fundamentals Configuration Guide, Release 4.2
Cisco Nexus 2000 Series Fabric Extender Software Configuration Guide
Maintain and Operate Guides
Cisco Nexus 5000 Series NX-OS Operations Guide
Installation and Upgrade Guides
Cisco Nexus 5000 Series and Cisco Nexus 5500 Platform Hardware Installation Guide
Cisco Nexus 2000 Series Hardware Installation Guide
Cisco Nexus 5000 Series NX-OS Software Upgrade and Downgrade Guide, Release 4.2(1)N1(1)
Cisco Nexus 5000 Series Hardware Installation Guide
|
xvi |
OL-15902-02 |
|
|
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Regulatory Compliance and Safety Information for the Cisco Nexus 5000 Series Switches and Cisco Nexus 2000 Series Fabric Extenders
Licensing Guide
Cisco NX-OS Licensing Guide
Command References
Cisco Nexus 5000 Series Command Reference
Technical References
Cisco Nexus 5000 Series and Cisco Nexus 2000 Series Fabric Extender MIBs Reference
Error and System Messages
Cisco NX-OS System Messages Reference
Troubleshooting Guide
Cisco Nexus 5000 Troubleshooting Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-02 |
xvii |
|
Preface
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Cisco Nexus 5000 Series Hardware Installation Guide
|
xviii |
OL-15902-02 |
|
|
|
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
C H A P T E R 1
Overview
This chapter provides an overview of the Cisco Nexus 5000 Series switches, which include the Cisco Nexus 5000 Platform switches and the Cisco Nexus 5500 Platform switches. The overview of each of these switches includes information on the expansion modules, power supplies, and fan modules that you can include with them.
This chapter includes the following sections:
•Cisco Nexus 5500 Platform Switches, page 1-1
•Cisco Nexus 5000 Platform Switches, page 1-29
Cisco Nexus 5500 Platform Switches
The Cisco Nexus 5500 Platform supports the following application scenarios, many of which require the installation of other products:
•As an access-layer switch, it can be used purely as a 1- and 10-Gigabit Ethernet switch, consolidating 10 Gigabit Ethernet connections into a smaller number of server connections trunked to the aggregation layer.
•As a smaller-scale aggregation switch, it can be used as a Layer 3 1- and 10-Gigabit Ethernet switch, consolidating multiple 1- and 10-Gigabit Ethernet connections from a data center access layer.
•In conjunction with the Cisco Nexus 2248T GE Ethernet Fabric Extender, the Cisco Nexus 5500 Platform can be a high-density 1-Gigabit Ethernet switching system, consolidating more than 900 Gigabit Ethernet connections within a single management plane.
•In conjunction with the Cisco Nexus 2232T 10GE Fabric Extender, it can be a high-density switching system, consolidating more than 600 10-Gigabit Ethernet connections within a single management plane.
•In conjunction with the Cisco Nexus 2224TM 10GE Fabric Extender, it can be a high-density switching system, consolidating more than 600 10-Gigabit Ethernet connections within a single management plane
•As a rack-level I/O consolidation platform, the switch carries Ethernet traffic from servers to the aggregation layer and carries FC traffic to existing Fibre Channel SANs.
•As a crucial element in data center I/O consolidation, the switch enables I/O consolidation at the access layer and provides interoperability with the Cisco Nexus 5500 Platform and other standards-based products.
This section describes the Cisco Nexus 5500 Platform switches and contains these sections:
• Cisco Nexus 5596UP Switch, page 1-2
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-01 |
1-1 |
|
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
•Cisco Nexus 5596T Switch, page 1-12
•Cisco Nexus 5548UP and 5548P Switches, page 1-17
Cisco Nexus 5596UP Switch
This section describes the Cisco Nexus 5596UP switch and its components. This section includes the following topics:
•Features, page 1-2
•Chassis, page 1-2
•Expansion Modules, page 1-4
•Ports, page 1-7
•Power Supply, page 1-8
•Fan Module, page 1-10
•Transceivers, page 1-11
Features
The Cisco Nexus 5596UP switch is a top-of-rack, 10-Gigabit Ethernet and Fibre channel over Ethernet (FCoE) switch offering up to 1920 Gigabit throughput and up to 96 ports. The switch has 48 1- and 10-Gigabit Ethernet and FCoE ports and three expansion slots. As a top-of-rack switch, all the servers in the rack connect to the Cisco Nexus 5596UP switch, and it connects to the LAN or SAN.
The Cisco Nexus 5596UP switch has the following features:
•48 fixed 1- and 10-Gigabit Ethernet server connection ports on the back of the switch
•Three slots on the back of the switch for optional expansion modules, which can be either a 16-port 10-Gigabit generic expansion module 2 (GEM2) or a layer 3 GEM2
•Two slots on the front of the switch for hot swap-capable power supplies, which provide front-to-back airflow for cooling
•Four slots on the front of the switch for hot swap-capable fan modules.
•Layer 2 or Layer 3 I/O modules
•One USB port on the front of the switch
Chassis
The Cisco Nexus 5596UP chassis is 2 RU or 3.47 inches (8.8 cm) tall, 17.3 inches (43.9 cm) wide, and 29.5 inches (74.9 cm) deep. It is designed to be mounted in a standard 19-inch wide rack. The front of the switch, shown in Figure 1-1, has a USB port, four Ethernet and ports (two cross-connect ports, one management port, and one console port), two power supplies, and four fan modules.
Cisco Nexus 5000 Series Hardware Installation Guide
1-2 |
OL-15902-01 |
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Figure 1-1 Front View of the Cisco Nexus 5596UP Switch
1 |
USB port |
4 |
System status LED |
|
|
|
|
2 |
Management and console ports (two RJ-45 Ethernet connector |
5 |
Two power supplies |
|
ports on the left, a RJ-45 network management connector on the |
|
|
|
upper right, and a console connector on the lower right) |
|
|
|
|
|
|
3 |
Identifier LED |
6 |
Four fan modules |
|
|
|
|
The management and console ports are in a 2 x 2 stacked RJ-45 jack. Figure 1-2 shows a close-up view of these ports. For information about the connector port LEDs, see Table D-1 on page D-2.
Figure 1-2 Management and Console Ports
2 |
3 |
4 |
1
239021
5
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-01 |
1-3 |
|
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
1 |
Internal cross-connect ports |
4 |
Network management port |
|
|
|
|
2 |
Link LED (left LED) |
5 |
Console port |
|
|
|
|
3 |
Activity LED (right LED) |
|
|
|
|
|
|
The rear of the Cisco Nexus 5596UP chassis, shown in Figure 1-3, has 48 fixed 10-Gigabit Ethernet data ports on the bottom and three slots for optional expansion modules on top.
Figure 1-3 Rear View of the Cisco Nexus 5596UP Switch
1 |
Expansion modules, shown here with three |
3 |
System status LED |
|
16-port Universal GEM2 modules (can also |
|
|
|
have Layer 3 GEM2 modules) |
|
|
|
|
|
|
2 |
Identifier LED |
4 |
48 fixed 1- and 10-Gigabit Ethernet ports |
|
|
|
|
Note The L1/L2/Mgmt1 ports are not usable. They are disabled at this time.
Expansion Modules
Expansion modules allow the Cisco Nexus 5596UP switch to be configured as cost-effective 10-Gigabit Ethernet switches and as I/O consolidation platforms with native Fibre Channel connectivity.
The Cisco Nexus 5596UP switch has three slots that can be used for the following optional expansion modules:
•4-port QSFP expansion module
•16-port Universal (Fibre Channel and Ethernet) GEM (N55-M16UP) that provides 8-, 4-, 2-, or 1-Gbps Fibre Channel and 1- or 10-Gigabit Ethernet ports
Cisco Nexus 5000 Series Hardware Installation Guide
1-4 |
OL-15902-01 |
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
•Layer 3 GEMs (N55-M160L3 and N55-M160L3-V2) provide 160 Gbps of Layer 3 services. The N55-M160L3-V2 uses a newer version of the Layer 3 ASIC that enables higher table sizes in a future software release from 8K host entries to 16K host entries or from 4K multicast routes to 8K multicast routes (IPv4).
You can hot swap the expansion modules during operations.
This section includes the following topics:
•4-port QSFP GEM, page 1-5
•16-port Universal GEM2, page 1-5
•Layer 3 GEM, page 1-6
4-port QSFP GEM
he 16-port Universal GEM2, shown in Figure 1-5, has 16 8-, 4-, 2-, or 1-Gbps Fibre Channel or 1- and 10-Gigabit Ethernet ports. This module is a field-replaceable unit (FRU) that you can hot swap during operations.
Figure 1-4 16-Port Universal GEM2
1
2
4
237977
16-port Universal GEM2
The 16-port Universal GEM2, shown in Figure 1-5, has 16 8-, 4-, 2-, or 1-Gbps Fibre Channel or 1- and 10-Gigabit Ethernet ports. This module is a field-replaceable unit (FRU) that you can hot swap during operations.
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-01 |
1-5 |
|
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Figure 1-5 16-Port Universal GEM2
1
2
4
237977
1 |
Status LED |
3 |
16 ports supporting 8-, 4-, 2-, or 1-Gbps transceivers or 1- and |
|
|
|
10-Gigabit transceivers |
|
|
|
|
2 |
Eject lever |
4 |
Captive screw that locks the eject lever in a closed position |
|
|
|
|
See Figure 1-7 on page 1-7 to see how ports are grouped and numbered on the Fibre Channel plus Ethernet expansion module.
Layer 3 GEM
The Layer 3 GEMs (N55-M160L3 and N55-M160L3-V2 ), shown in Figure 1-6, provide 160 Gbps of Layer 3 services. The expansion modules are field-replaceable units (FRU’s). The N55-M160L3-V2 uses a newer version of the Layer 3 ASIC that enables higher table sizes in a future software release from 8K host entries to 16K host entries or from 4K multicast routes to 8K multicast routes (IPv4).
Cisco Nexus 5000 Series Hardware Installation Guide
1-6 |
OL-15902-01 |
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Figure 1-6 Layer 3 GEM2
1 |
Status LED |
3 |
Captive screw that locks the eject lever in a |
|
|
|
closed position |
|
|
|
|
2 |
Ejector lever |
|
|
|
|
|
|
Ports
Each port on the Cisco Nexus 5596UP switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right. The 48 fixed ports support 8-, 4-, 2-, or 1-Gbps Fibre Channel transceivers and 1- or 10-Gigabit Ethernet transceivers.
Figure 1-7 shows how ports are numbered and grouped by function for both the fixed ports and the Fibre Channel plus Ethernet expansion module ports.
Figure 1-7 Port Numbering of Fixed Ports and Fibre Channel Plus Ethernet Expansion Module Ports
1 |
Port numbering for the 16-port GEM |
2 |
Port numbering for the 48 fixed ports |
|
|
|
|
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-01 |
1-7 |
|
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Power Supply
The Cisco Nexus 5596UP uses a front-end power supply. The chassis has slots for two power supplies. The Cisco Nexus 5596UP switch is fully functional with one power supply, but you can include a second power supply for power redundancy.
Table 1-1 lists the power supplies that you can order with the Cisco Nexus 5500 Platform switches.
Table 1-1 |
Power Supplies for the Cisco Nexus 5500 Platform switches |
|
|
|
|
Part Number |
|
Power Supply |
|
|
|
N55-PAC-750W |
Cisco Nexus 5548P/5548UP PSU Front-to-Back Airflow module, A/C, |
|
|
|
100-240V, 750W |
|
|
|
N55-PAC-750W(=) |
Cisco Nexus 5548P/5548UP PSU Front-to-Back Airflow module spare, |
|
|
|
A/C, 100-240V, 750W |
|
|
|
N55-PAC-750W-B |
Cisco Nexus 5548UP PSU Back-to-Front Airflow module, A/C, 100-240V, |
|
|
|
750W |
|
|
|
N55-PAC-750W-B(=) |
Cisco Nexus 5548UP PSU Back-to-Front Airflow module spare, A/C, |
|
|
|
100-240V, 750W |
|
|
|
N55-PDC-750W |
Cisco Nexus 5548P/5548UP PSU Front-to-Back Airflow module, D/C, -40 |
|
|
|
to -72VDC, 750W |
|
|
|
N55-PDC-750W(=) |
Cisco Nexus 5548P/5548UP PSU Front-to-Back Airflow module spare, |
|
|
|
D/C, -40 to -72VDC, 750W |
|
|
|
N55-PAC-1100W |
Cisco Nexus 5596UP PSU Front-to-Back Airflow module, A/C, 100-240V, |
|
|
|
1100W |
|
|
|
N55-PAC-1100W(=) |
Cisco Nexus 5596UP PSU Front-to-Back Airflow module spare, A/C, |
|
|
|
100-240V, 1100W |
|
|
|
N55-PAC-1100W-B |
Cisco Nexus 5596UP/5596T PSU Back-to-Front Airflow module, A/C, |
|
|
|
100-240V, 1100W |
|
|
|
N55-PAC-1100W-B(=) |
Cisco Nexus 5596UP/5596T PSU Back-to-Front Airflow module spare, |
|
|
|
A/C, 100-240V, 1100W |
|
|
|
N55-PDC-1100W |
Cisco Nexus 5596UP/5596T PSU , DC Front-to-Back, 1100 W |
|
|
|
|
Note Front to Back (FAF) Airflow and DC Power Supply is now supported for the Cisco Nexus 5596T. For details see the Cisco Nexus 5500 Datasheet.
Figure 1-8 shows an AC power supply. For more information on the LEDs, see Table D-1 on page D-2.
Cisco Nexus 5000 Series Hardware Installation Guide
1-8 |
OL-15902-01 |
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Figure 1-8 AC Power Supply for the Cisco Nexus 5596UP Switch
1
3 2
237868
1 Failure (top) and Power (bottom) LEDs |
3 Release lever |
2 Handle
Figure 1-9 shows the NXA-PAC-1100W .
Figure 1-9 NXA-PAC-1100W
Figure 1-10 shows the NXA-PAC-1100W-B
Cisco Nexus 5000 Series Hardware Installation Guide
|
OL-15902-01 |
1-9 |
|
|
|
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Figure 1-10 NXA-PAC-1100W-B
Figure 1-11 shows NXA-PDC-1100W
Figure 1-11 |
NXA-PDC-1100W |
Note Never leave a power supply slot empty. If you remove a power supply, replace it with another one. If you do not have a replacement power supply, leave the non functioning one in place until you can replace it.
Fan Module
The Cisco Nexus 5596UP switch has four fan modules. Although the switch can function when a fan stops functioning within a fan module, if a whole fan module stops functioning, you must replace the fan module. The Cisco Nexus 5596UP supports the reverse air flow fan tray (N5596UP-FAN-B).
Figure 1-12 shows a fan module.
|
Cisco Nexus 5000 Series Hardware Installation Guide |
1-10 |
OL-15902-01 |
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Caution You must order all fan modules and power supplies in the same chassis so that they have the same direction of airflow with coolant air entering the chassis from the cold aisle and exhausting to the hot aisle.
Figure 1-12 Cisco Nexus 5596 Fan Module
1 
2
3
1Captive screw
2Status LED
239022
3 Handle
The bicolor status LED indicates fan tray health. Green indicates normal operation, while amber indicates a fan failure. For more information about LEDs, see Table D-1 on page D-2.
Transceivers
The Cisco Nexus 5596 switch supports both SFP and SFP+ Ethernet transceivers and SFP Fibre Channel transceivers.
This section includes the following topics:
•SFP+ Transceivers, page 1-11
•SFP+ Copper Cables, page 1-12
•SFP Fibre Channel Transceivers, page 1-12
•CWDM Optics, page 1-12
SFP+ Transceivers
The enhanced SFP+ 10-Gigabit Ethernet transceiver module is a bidirectional device with a transmitter and receiver in the same physical package. It has a 20-pin connector on the electrical interface and duplex LC connector on the optical interface.The Cisco Nexus 5596 supports the SFP-10G-SR transceiver.
|
|
Cisco Nexus 5000 Series Hardware Installation Guide |
|
|
|
|
|
|
|||
|
OL-15902-01 |
|
|
1-11 |
|
|
|
|
|
||
Chapter 1 Overview
Cisco Nexus 5500 Platform Switches
Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m .
Model |
Description |
|
|
SFP-10G-SR |
10-Gigabit Ethernet—short range SFP+ module |
|
|
SFP+ Copper Cables
Copper cables are available for use with the 10-Gigabit Ethernet SFP+ module. The cables come in the following lengths:
•1 m, 30 AWG
•3 m, 28–30 AWG
•5 m, 26–28 AWG
Model |
Description |
|
|
SFP-H10GB-CU1M |
10GBASE-CU SFP+ Cable (1 meter) |
|
|
SFP-H10GB-CU3M |
10GBASE-CU SFP+ Cable (3 meters) |
|
|
SFP-H10GB-CU5M |
10GBASE-CU SFP+ Cable (5 meters) |
|
|
SFP Fibre Channel Transceivers
The Cisco Nexus 5596 switch also supports the following SFP Fibre Channel transceiver:
Model |
Description |
|
|
DS-SFP-FC4G-SW |
4-, 2-, or 1-Gbps Fibre Channel—Short |
|
wavelength SFP module |
|
|
CWDM Optics
The Cisco Nexus 5596 switch also supports the following CWDM optics:
Model |
Description |
|
|
DS-CWDM4G1470= |
1470 nm CWDM 1/2/4-Gbps Fibre Channel SFP |
|
|
DS-CWDM4G1610= |
1610 nm CWDM 1/2/4-Gbps Fibre Channel SFP |
|
|
Cisco Nexus 5596T Switch
The Nexus 5596T is based on the same ASIC and chassis as the 5596UP. The Nexus 5596T switch is a 2RU switch, with 32 fixed ports of 10G BaseT and 16 fixed 10G Unified ports, which support (Ethernet, FC, FCoE). All the existing GEMs supported on the Nexus 5500 switches will be supported on the Nexus 5596T. In addition, the Nexus 5596T will also support the new 12 port 10G BaseT expansion module. With this module,you can use the Nexus 5596T to deploy upto 68 ports of 10G BaseT in a 2RU
|
Cisco Nexus 5000 Series Hardware Installation Guide |
1-12 |
OL-15902-01 |
Loading...