Cisco Systems M170 User Manual

Size:
3.37 Mb
Download

SLIDERAILINSTALLATIONINSTRUCTIONS

For Cisco C170, M170, and S170 Appliances

and

Cisco 5512-X,5515-X,5525-X,5545-X,5555-XAdaptive Security Appliances and

Cisco IPS 4345 and 4360

1Verify the Box Contents

2Disassemble the Slide Rail

3Attach Inner Rails to the Chassis

4Verify the Rack Type

5Round Hole Racks

6Threaded Hole Racks

7Attach the Outer Slide Rail to Round and Square Hole Racks

8Attach the Outer Slide Rail to Threaded Hole Racks

9Install the Chassis

10Secure the Chassis

Obtaining Documentation and Submitting a Service Request

1 Verify the Box Contents

Remove the contents from the box and verify that it contains the following items for all rack types:

A Slide Rails (x2) (preconfigured for square hole racks)

B Phillipsflat-headscrews for Inner Slide (x2)

For round hole racks, you also need the following:

C Round Hole Inserts (x4)

For threaded hole racks, you also need the following:

D Threaded Hole Brackets (x2)

E Threaded Hole Standoffs (x2)

F Phillipspan-headscrews for threaded hole racks (x8)

A

B C D E F

300885

Tools Required:

Phillips screwdriver

Flat-headscrewdriver (for threaded hole racks)

2

2 Disassemble the Slide Rail

Pull the inner slide rail from the outer slide rail.

Front

Slide the plastic tab forward, and pull the inner slide rail to disconnect it from the outer slide rail.

330908

Repeat the steps on this page for the other slide rail.

3

3 Attach Inner Rails to the Chassis

Align one of the inner slide rail key holes over the chassis shoulder screw on one side. Slide the inner slide rail forward so that the shoulder screw is securely in place.

330907

Use a Phillips screwdriver to secure the inner slide rail with one Phillips flat-headscrewB .

330905

Secure the other inner slide rail to the chassis by repeating the previous steps on this page.

330904

4

4 Verify the Rack Type

The slide rails are pre-assembledfor square hole racks. See the following steps for the different rack types:

Square hole racks. Go to“Attach the Outer Slide Rail to Round and Square Hole Racks” on page 8.

Round hole racks. Go to“Round Hole Racks” on page 6.

Threaded hole racks. Go to“Threaded Hole Racks” on page 7.

The following figure shows the slide rail with square hole rack inserts.

330903

5

5 Round Hole Racks

Using a Phillips head screwdriver, remove the square insert from the rear of the rail. Keep the two Phillips head screws.

330884

Remove the square insert from the front of the rail. Keep the two Phillips head screws.

330882 Align the round hole insertC to the rear of the rail, and secure it with two of the saved screws.

330881 Align the round hole insertC to the front of the rail over the hooks, and secure it with two of the saved screws.

330880

See “Attach the Outer Slide Rail to Round and Square Hole Racks” on page 8.

6

6 Threaded Hole Racks

Using a Phillips head screwdriver, remove the square hole insert from the rear of the rail.

330884

Remove the square hole insert from the front of the rail.

330882 Align the threaded hole bracketD to the front of the rail over

the hooks. Secure it with the threaded hole standoff E using aflat-headscrewdriver.

330878

No additional hardware is necessary for the rear adapter.

330876

Repeat these steps page for the other slide rail. Go to the“Attach the Outer Slide Rail to Threaded Hole Racks” section on page 9.

7

7 Attach the Outer Slide Rail to Round and Square Hole Racks

Align the front of one of the outer slide rails with the rack upright, push it forward, and click it into place. Align the rear of the outer slide rail with the rack upright, pull the release tab, push the slide rail toward the rack, release the tab, and click it into place.

Note For racks shorter than 24 inches in depth, remove the rear bracket with a Phillips head screwdriver, pull the release tab, and adjust the slide rail to the appropriate length for the rack.

Front of

Rack Rear of

Rack

Rear of

Bracket

330901

Secure the other outer slide rail to the rack by repeating the previous steps.

330872

Go to the “Install the Chassis” section on page 10.

8

8 Attach the Outer Slide Rail to Threaded Hole Racks

Align the slide rail to the front rack post. Secure it with two of the included Phillips pan-headscrewsF .

330883

Align the slide rail to the rear rack post. Secure it with two of the included Phillips pan-headscrewsF .

330875

Align the other slide rail to the rack by repeating the previous steps on this page.

330872

Go to the “Install the Chassis” section on page 10.

9

9 Install the Chassis

Align the inner slide rails to the outer slide rails. Install the inner slide rails into the outer slide rails until they lock into place.

330889

Pull the side release tabs to unlock the inner slide rail, and push the chassis assembly into the rack.

330898

10

10 Secure the Chassis

Secure the chassis to the rack with the front captive screws.

330890

Obtaining Documentation and Submitting a

Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.ht ml

Subscribe to the What’s New in Cisco Product Documentationas an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.

11

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

© 2012 Cisco Systems, Inc. All rights reserved.

 

 

 

 

 

 

 

 

Americas Headquarters

Asia Pacific Headquarters

Europe Headquarters

Cisco Systems, Inc.

Cisco Systems (USA) Pte. Ltd.

Cisco Systems International BV Amsterdam,

San Jose, CA

Singapore

The Netherlands

Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-19691-04