Cisco Systems HIG880 User Manual

Size:
2.57 Mb
Download

Cisco 860 Series and Cisco 880 Series

Integrated Services Routers Hardware

Installation Guide

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706USAhttp://www.cisco.com Tel: 408526-4000

800 553-NETS(6387) Fax: 408527-0883

Text Part Number:

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequencyenergy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequencyenergy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMEDSUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX,Post-Routing,Pre-Routing,ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0501R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

© 2008 Cisco Systems, Inc. All rights reserved.

Preface

This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information. It contains the following sections:

Objective, page iii

Audience, page iii

Organization, page iv

Conventions, page iv

Related Documentation, page xi

Obtaining Documentation and Submitting a Service Request, page xi

Objective

This guide provides an overview and explains how to install, connect, and perform initial configuration for the wireless and nonwireless Cisco 860 series and Cisco 880 series integrated services routers (ISRs). Some information may not apply to your particular router model.

For warranty, service, and support information, see the “CiscoOne-YearLimited Hardware Warranty Terms” section in the documentReadme First for the Cisco 800 Series Integrated Services Routers that was shipped with your router.

Audience

This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar with Cisco routers and Cisco IOS software and features.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

iii

 

Preface

Organization

This guide is organized into the following chapters and appendix.

Product Overview

Describes briefly the router models and the hardware

 

features available.

 

 

Installing the Router

Lists items shipped with the router, equipment and

 

tools necessary for installing the router, safety

 

warnings and guidelines, and the procedures for

 

installing the router.

 

 

Connecting the Router

Describes typical connections for the router,

 

procedures for connecting the router to various

 

devices, and how to verify the connections.

 

 

Initial Configuration

Provides the procedures for initially configuring the

 

router settings.

 

 

Appendix A, “Technical Specifications”

Provides router, port, and cabling specifications.

 

 

Conventions

This section describes the conventions used in this guide.

Note Meansreader take note. Notes contain helpful suggestions or references to additional information and material.

Caution This symbol meansreader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

iv

OL-16193-01

 

 

 

Preface

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vousavec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,référez-vousau numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

v

 

Preface

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-secom as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

vi

OL-16193-01

 

 

 

Preface

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

vii

 

Preface

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-secom as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

viii

OL-16193-01

 

 

 

Preface

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

ix

 

Preface

Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use ofUL-certifiedcables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited toCISCO-designatedproducts. Statement 371.

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.Statement 1015

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.Statement 1035

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.Statement 1037

Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.Statement 1038

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

x

OL-16193-01

 

 

 

Preface

Related Documentation

In addition to the Cisco 860 series and Cisco 880 series ISR Hardware Installation Guide (this document), the Cisco 860 series and Cisco 880 series ISR documentation set includes the following documents:

Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide

Software Activation for Cisco Integrated Services Routers

Cisco Software Activation Tasks and Commands

Cisco Software Activation Conceptual Overview

Declarations of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g and 802.11b/g Radios

Cisco IOS Release Notes

Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T

Cisco IOS Security Configuration Guide, Release 12.4T

Cisco IOS Security Command Reference, Release 12.4T

Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges, versions 12.4(10b) JA and 12.3(8) JEC

Wireless LAN Controllers

Unified Wireless LAN Access Points

Cisco IOS Voice Port Configuration Guide

SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways

Cisco CP Express User’s Guide

Searching Cisco Documents

To search a Hyper Text Markup Language (HTML) document using a web browser, use the Ctrl+F (Windows) or Cmd+F (Apple) sequences. In most browsers the option to search whole words only, invoke case sensitivity, or search forward and backward are also available.

To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl+F) or the Full Reader Search window (Shift+Ctrl+F). Use the Find toolbar to find words or phrases within one specific document. Use the Full Reader Search window to search multiple PDF files simultaneously as well as change case sensitivity, and other options. Adobe Reader comes with online help with more information regarding searching PDF documents.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

xi

 

Preface

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

xii

OL-16193-01

 

 

 

C H A P T E R 1

Product Overview

This chapter provides an overview of the features available for the Cisco 860 series and Cisco 880 series integrated services routers (ISRs), and contains the following sections:

General Description, page 1-1

Cisco 860 Series ISRs, page 1-2

Cisco 880 Series ISRs, page 1-3

Hardware Features, page 1-8

Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmapthat ships with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.

Note The illustrations in this document show a wireless router. Both wireless and nonwireless models are available in the Cisco 860 series and Cisco 880 series ISRs. Port and feature locations are similar for both wireless and nonwireless routers.

General Description

The Cisco 860 series and Cisco 880 series ISRs provide data, voice, wireless, integrated Virtual Private Network (VPN), and backup capability to corporate teleworkers and to remote and small offices with fewer than twenty users. These routers are capable of bridging and multiprotocol routing between LAN and WAN ports, and provide advanced features such as (global industry standard) symmetrical high-speedDSL (G.SHDSL), 802.11n, quality of service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL).

The Cisco 860 series and Cisco 880 series ISRs have a desktop form factor with built-inwall-mountfeatures. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

1-1

 

 

 

Chapter 1 Product Overview

Cisco 860 Series ISRs

Cisco 860 Series ISRs

The Cisco 860 series ISRs are fixed-configurationdata routers that support the following features:

An integrated 4-port10/100 Ethernet switch for connecting to the LAN

A10/100 Fast Ethernet (FE) port for connecting to the WAN

Optional, embedded-wirelessaccess point

Figure 1-1 shows the front panel details of the Cisco 860 wireless router.

Figure 1-1Front Panel of the Cisco 860 Series Wireless ISR

231969

1

1 LEDs

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-2

OL-16193-01

 

 

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do not have antennas or connectors on the back panel. However, the feature locations are similar for all Cisco 860 series routers.

Figure 1-2Back Panel of the Cisco861-WISR

Cisco 861W

WAN

FE 4

232181

 

1

2

 

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

1

Primary WAN port—10/100FE

 

5

Reset button

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Antenna—captiveomnidirectional dipole

6

Power connector

 

 

 

 

 

WLAN antenna (wireless models only)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

4-port10/100 Ethernet switch

 

7

Earth ground connector

 

 

 

 

 

 

 

 

 

 

 

4

Serial port—consoleor auxiliary

 

8

Kensington security slot

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco 880 Series ISRs

The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

Integrated 4-port10/100 Ethernet switch for connecting to the LAN

10/100 FE, or a G.SHDSL port for connecting to the WAN

Optional, 802.11n embedded-wirelessaccess point

Optional, Power over Ethernet (PoE)

DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB The following features are located on the front panel:

USB 1.1 port

Express card slot for third-generation(3G) cellular data WAN connectivity, available only on the Cisco 88xG models

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

1-3

 

 

 

Chapter 1 Product Overview

Cisco 880 Series ISRs

Cisco 880 Series Data Routers

The Cisco 880 series data routers provide integrated VPN, wireless, 3G, and backup capabilities. Figure 1-3 andFigure 1-4 show the features available on Cisco 880 series data routers. Some of the features shown may not be available on your router.

Figure 1-3 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G card slot are located on the front panel.

Figure 1-3Front Panel of the Cisco 880 Series Wireless Data Router

231950

1

2

3

1 LED

3 USB port

 

23G express card slot—Supportsthird-party1

3G card (Cisco 88xG models only)

1.See the Cisco 880 series ISRs data sheet for supported vendors.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-4

OL-16193-01

 

 

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-4 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have antennas or connectors on the back panel. However, the feature locations are similar across all Cisco 880 series data routers.

Figure 1-4Back Panel of the Cisco888-WData Router

 

 

 

 

 

 

 

 

 

231951

1

2

3

4

5

6

7

8

9

10

1

ISDN port—notavailable on 3G models

6

PoE power connector

 

 

 

 

2

Primary WAN port—G.SHDSLor 10/100 FE1

7

Reset button

3

Antenna—captiveomnidirectional dipole

8

Power connector

 

WLAN antenna (wireless models only)

 

 

 

 

 

 

4

4-port10/100 Ethernet switch

9

Earth ground connector

 

 

 

 

5

Serial port—consoleor auxiliary

10

Kensington security slot

 

 

 

 

1. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2.

Cisco 880 Series Voice Routers

The Cisco 880 series voice routers provide managed voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or Basic Rate Interface (BRI) connections. Figure 1-5,Figure 1-6,andFigure 1-7,show the features available on the Cisco 880 series voice routers. The features available vary depending on the router model. Some features may not be available on your router.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

1-5

 

 

 

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-5 shows the front panel details of the Cisco 880 wireless voice router.

Figure 1-5Front Panel of the Cisco 880 Series Wireless Voice Router

270495

1

2

1 LEDs

2 USB port

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-6

OL-16193-01

 

 

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-6 shows the back panel details of the Cisco880SRST-Wvoice router.

Figure 1-6Back Panel of the CiscoC881SRST-WVoice Router

 

 

 

 

 

 

 

 

 

 

241904

6

1

2

2

3

4

5

7

8

9

10

1

Primary WAN port—10/100FE

6

Antenna—captivewireless omnidirectional

 

 

 

dipole WLAN antenna (wireless models only)

 

 

 

 

2

Voice ports—fourFXS1/DID2 ports, one

7

Reset button

 

FXO3 port with TBP4 power failover

 

 

3

4-port10/100 Ethernet switch

8

Power connector

 

 

 

 

4

Serial port—consoleor auxiliary

9

Earth ground connector

 

 

 

 

5

PoE power connector

10

Kensington security slot

 

 

 

 

1.FXS = Foreign Exchange Station.

2.DID = Direct Inward Dialing.

3.FXO = Foreign Exchange Office.

4.TBP = trunk bypass.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

1-7

 

 

 

Chapter 1 Product Overview

Hardware Features

Figure 1-7 shows the back panel details of the Cisco888SRST-Wvoice router.

Figure 1-7Back Panel of the CiscoC888SRST-WVoice Router

 

 

 

 

 

 

 

 

 

 

241905

2

1

2

6

3

4

5

7

8

9

10

1

Primary WAN port—G.SHDSL

6

Antenna—captivewireless omnidirectional

 

 

 

dipole WLAN antenna (wireless models only)

 

 

 

 

2

Voice ports—fourFXS1/DID2 ports, and one

7

Reset button

 

voice BRI3 port

 

 

3

4-port10/100 Ethernet switch

8

Power connector

 

 

 

 

4

Serial port—consoleor auxiliary

9

Earth ground connector

 

 

 

 

5

PoE power connector

10

Kensington security slot

 

 

 

 

1.FXS = Foreign Exchange Station.

2.DID = Direct Inward Dialing.

3.BRI = Basic Rate Interface.

Hardware Features

This section provides an overview of the following hardware features for the Cisco 860 series and Cisco 880 series ISRs. A feature summary is available at the end of this section.

Kensington Lock

Reset Button

LEDs

Memory

USB Port

Fan

Power over Ethernet Module

3G Cellular Data WAN Connectivity

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-8

OL-16193-01

 

 

Chapter 1 Product Overview

Hardware Features

Wireless LAN Connectivity

Feature Summary

Kensington Lock

A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment.

Reset Button

The Reset button resets the router configuration to the default configuration set by the factory. To reset the hardware and its embedded wireless access point, simultaneously press the reset button while applying power to the router.

Note When you reset the hardware when the embedded wireless access point is running Cisco Unified IOS software, the router will shutdown but the access point will continue running. Clients with

Cisco Unified IOS software are controlled by a Wireless LAN Controller (WLC) and can only be reset by the controller.

LEDs

The LEDs are located on the front panel of the router. Table 1-1 describes the LEDs for the Cisco 860 series and the Cisco 880 series ISRs.

Table 1-1

LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs

 

 

 

 

 

 

 

 

LED

 

Color

Description

860 Series

880 Series

 

 

 

 

 

 

Power OK

 

Green

On—DCpower is being supplied to the router and the

All models

All models

 

 

 

Cisco IOS software is running.

 

 

 

 

 

Blinking—Bootupis in process, or the router is in ROMMON

 

 

 

 

 

monitor mode.

 

 

 

 

 

Off—Poweris not supplied to the router.

 

 

 

 

 

 

 

Link Status FE10

Green

On—Ethernetport is connected.

All models

All models

Link Status FE1

 

 

Blinking—Datais either being received or being transmitted.

 

 

 

 

 

 

 

 

Link Status FE2

 

 

Off—Ethernetport is not connected.

 

 

 

 

 

 

 

 

Link Status FE3

 

 

 

 

 

 

 

 

 

 

FE WAN Port Link

Green

On—Portis connected.

861 models

881 models

Status

 

 

Blinking—Datais either being received or being transmitted.

 

 

 

 

 

 

 

 

 

 

Off—Portis not connected.

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

1-9

 

 

 

Chapter 1 Product Overview

Hardware Features

Table 1-1

LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued)

 

 

 

 

 

 

 

 

 

 

 

 

LED

 

Color

Description

860 Series

880 Series

 

 

 

 

 

 

 

 

WLAN (2.4 GHz)

Green

On—Radiois connected, SSID2 is configured, signal is being

Wireless

Wireless

 

 

 

 

 

 

transmitted, and client is associated, but no data is being

models

models

 

 

 

 

 

 

received or being transmitted.

 

 

 

 

 

 

 

 

 

 

Slow blinking—Radiois connected, SSID is configured, and

 

 

 

 

 

 

 

 

 

 

beacons are being transmitted.

 

 

 

 

 

 

 

 

 

 

Fast blinking—Datais either being received or being

 

 

 

 

 

 

 

 

 

 

transmitted.

 

 

 

 

 

 

 

 

 

 

Off—Radiois shut down, and no SSID is configured.

 

 

 

 

 

 

 

 

 

 

 

 

 

WLAN LINK

 

Green

On—Wirelesslink is up.

Wireless

Wireless

 

(Autonomous

 

 

Blinking—Ethernetlink is up and data is either being

models

models

 

Mode)

 

 

 

 

 

 

 

 

 

received or being transmitted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off—Wirelesslink is down.

 

 

 

 

 

 

 

 

 

 

 

 

 

WLAN LINK

 

Green

On—Ethernetlink is up, wireless access point is

Wireless

 

(Unified Mode)

 

 

communicating with LWAPP controller.

 

models

 

 

 

 

 

 

Blinking—Ethernetlink is up, wireless access point is not

 

 

 

 

 

 

 

 

 

 

communicating with LWAPP controller.

 

 

 

 

 

 

 

 

 

 

Off—Ethernetlink is down.

 

 

 

 

 

 

 

 

 

 

 

 

 

PoE3

 

Green

On—PoEis connected and powered.

Models with

 

 

 

 

 

 

Off—PoEis not installed.

 

PoE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Amber

On—Faultwith the PoE.

 

 

 

 

 

 

 

 

 

 

 

 

 

VPN4

 

Green

On—VPNis connected.

All models

 

PPP5

 

Green

On—Atleast one PPP session is established.

All models

 

xDSL6 CD

 

Green

On—ThexDSL interface is connected to the DSLAM7.

888 models

 

 

 

 

 

 

Blink—Trainingto the line.

 

 

 

 

 

 

 

 

 

 

Off—Indicatesthat a connection has not been established or

 

 

 

 

 

 

 

 

 

 

the port is shut down.

 

 

 

 

 

 

 

 

 

 

 

 

 

xDSL Data

 

Green

Blink—ThexDSL interface is either receiving or transmitting

888 models

 

 

 

 

 

 

data.

 

 

 

 

 

 

 

 

 

 

Off—Nodata is being transmitted or being received.

 

 

 

 

 

 

 

 

 

 

 

 

Data BRI8 LINK

Green

On—ISDND channel is connected.

888 models

 

Data BRI B1

 

Green

Blinking—B1channel is either receiving or sending data, or

888 models

 

 

 

 

 

 

data is passing through ISDN channel 1.

 

 

 

 

 

 

 

 

 

 

 

 

 

Data BRI B2

 

Green

Blinking—B2channel is receiving or sending data, or data is

888 models

 

 

 

 

 

 

passing through ISDN channel 2.

 

 

 

 

 

 

 

 

 

 

 

 

 

3G9 WWAN10

 

Green

On—Serviceis established.

3G models

 

 

 

 

 

 

Slow Blinking—Searchingfor service.

 

 

 

 

 

 

 

 

 

 

Fast Blinking—Datais either being received or being

 

 

 

 

 

 

 

 

 

 

transmitted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

1-10

 

 

 

 

 

 

OL-16193-01

 

 

 

 

 

 

 

 

 

Chapter 1 Product Overview

Hardware Features

Table 1-1

LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued)

 

 

 

 

 

 

 

LED

 

Color

Description

860 Series

880 Series

 

 

 

 

 

 

3G RSSI11

 

Green

Off—Lowsignal strength (lower than-100dBm).

3G models

 

 

 

On—HighRSSI(-69dBm or higher).

 

 

 

 

 

Slow Blinking—Lowor medium RSSI(-99to-90dBm).

 

 

 

 

 

Fast Blinking—MediumRSSI(-89to-70dBm).

 

 

 

 

 

 

 

 

 

 

Amber

On—Noservice.

3G models

 

 

 

 

 

 

3G GSM12

 

Green

On—Serviceis established.

3G models

 

 

 

Off—Noservice.

 

 

 

 

 

 

 

 

3G CDMA13

 

Green

On—Serviceis established.

3G models

 

 

 

Off—Noservice.

 

 

 

 

 

 

 

 

FXO14 Voice

 

Green

On—FXOport is connected.

881-SRST15

 

 

 

Blinking—FXOport is either receiving or transmitting data.

 

 

 

 

 

 

 

 

BRI Voice LNK

 

Green

On—BRIinterface is connected.

SRST

 

 

 

 

 

models

 

 

 

 

 

 

BRI Voice B1

 

Green

On—BRIB1 channel is connected.

SRST

 

 

 

Blinking—BRIB1 channel is either receiving or transmitting

 

models

 

 

 

 

 

 

 

 

data.

 

 

 

 

 

 

 

 

BRI Voice B2

 

Green

On—BRIB2 channel is connected.

SRST

 

 

 

Blinking—BRIB2 channel is receiving or transmitting data.

 

models

 

 

 

 

 

 

 

 

 

 

FXS16/DID17 Voice

Green

On—FXS/DIDport is connected.

SRST

 

 

 

Blinking—FXS/DIDport is either receiving or transmitting

 

models

 

 

 

 

 

 

 

 

data.

 

 

 

 

 

 

 

 

1.FE = Fast Ethernet.

2.SSID = Service Set Identifier.

3.PoE = Power over Ethernet.

4.VPN = Virtual Private Network.

5.PPP = Point-to-PointProtocol.

6.xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

7.DSLAM = digital subscriber line access multiplexer.

8.BRI = Basic Rate Interface.

9.3G = Third-Generation.

10.WWAN = wireless WAN.

11.RSSI = Received Signal Strength Indicator.

12.GSM = Global System for Mobile Communication.

13.CDMA = code division multiple access.

14.FXO = Foreign Exchange Office.

15.SRST = Survivable Remote Site Telephony.

16.FXS = Foreign Exchange Station.

17.DID = Direct Inward Dialing.

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

1-11

 

 

 

 

 

Chapter 1 Product Overview

Hardware Features

Memory

The Cisco 860 series and Cisco 880 series routers contain flash memory and main memory.

Flash Memory

The Cisco 860 series and Cisco 880 series ISRs use non-upgradableflash memory storage. Onboard flash memory contains the Cisco IOS software image, boot flash contains the ROMMON boot code, and quack contains the cookie configuration.

The default flash memory for the Cisco 860 series and Cisco 880 series ISRs is 128 MB. The default flash memory for the Cisco 880 series voice routers is 256 MB.

Note Flash memory is not upgradable. An external USB flash may be used if additional flash memory is needed.

Main Memory

The Cisco 860 series and Cisco 880 series routers contain 256 MB of onboard CPU memory. The Cisco 880 series routers contain a SODIMM expansion slot that accommodates a single PC2-4200,256 MB or 512 MB double data rate 2 (DDR2)small-outlineDIMM (SODIMM), for a maximum of 768 MB.

USB Port

A Universal Serial Bus (USB 1.1-compliant)port is located on the front panel. The USB port provides connection for USB devices such as security tokens and flash memory.

Fan

Some router models do not have a fan, while others have either one or two fans.

The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the router has booted, the fans will spin continuously at a speed determined by a variable-speedcontroller. The fans spin only as fast as necessary to minimize fan noise while maintaining a safe internal operating temperature.

Power over Ethernet Module

The 2-portPower over Ethernet (PoE) module provides power to 802.3af compliant devices connected to FE port 0 and FE port 1.

The 2-portPoE module is an option available only for the Cisco 880 series ISRs, and requires a 48 V external power adapter.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-12

OL-16193-01

Chapter 1 Product Overview

Hardware Features

3G Cellular Data WAN Connectivity

The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generationwide-areacellular technology that is used in voice telephony and broadband wireless data in a mobile environment.

The Cisco 88xG models come with a 34-mmexpress card slot ready for use with a commercial 3G card radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards see the Cisco 880 series ISRsdata sheet.

Wireless LAN Connectivity

The embedded wireless access point is preinstalled in the router as an optional feature. The wireless access point provides 802.11n wireless connectivity. The Cisco 860 series routers support autonomous features and network configurations. The Cisco 880 series routers support both autonomous and unified features and network configurations.

The wireless access point does not have an external console port for connections. To configure the wireless device, you must use a console cable to connect a PC to the host router’s console port as described in Chapter 3, “Connecting a Terminal or PC to the Console Port,” and then use the Cisco IOS CLI to access the interface.

Table 1-2 describes the radios and antenna for the Cisco 860 series and Cisco 880 series routers.

Table 1-2

Wireless Device Radios and Antennas

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum Data

 

 

Radio Module

 

Platform

Radio Band

 

Throughput1

Mode

Antenna

Single-band802.11n

Cisco 860 &

2.4 GHz

 

Up to 100 Mbps

Cisco 860 series:

Three captive 2-dBi

draft 2.0 radio module

880 series

 

 

 

autonomous only

omnidirectional dipole

 

 

routers

 

 

 

Cisco 880 series:

antennas

 

 

 

 

 

 

 

 

 

 

 

 

 

autonomous and

 

 

 

 

 

 

 

unified

 

 

 

 

 

 

 

 

 

1. Actual data rate is highly dependent on your wireless environment.

Feature Summary

Table 1-3 summarizes the hardware features available in the Cisco 860 series and Cisco 880 series ISRs.

Table 1-3

Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs

 

 

 

 

 

 

 

 

 

 

 

 

 

Feature

 

Description

860 Series

880 Series

 

 

 

 

 

 

 

 

Reset button

 

Resets the router configuration to the factory default.

All models

All models

 

 

 

 

 

 

 

 

FE1 built-in

 

Provides connection to 10/100BASE-T(10/100-Mbps)

All models

All models

 

switch ports

 

Fast Ethernet networks. The autosensing function in these

 

 

 

 

 

 

 

 

 

routers eliminates the need for a crossover cable and allows

 

 

 

 

 

 

 

 

 

the router to detect MDI2 or MDIX3 in any other PC or hub

 

 

 

 

 

 

 

 

 

with a straight-throughcable or a crossover cable.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-16193-01

 

 

 

 

 

1-13

 

 

 

 

 

 

 

 

 

Chapter 1 Product Overview

Hardware Features

Table 1-3

Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued)

 

 

 

 

 

Feature

 

Description

860 Series

880 Series

 

 

 

 

 

Console or AUX

 

Provides a connection to the terminal or PC for software

All models

All models

port

 

configuration or troubleshooting. The console port may be

 

 

 

 

configured as a virtual auxiliary port for dial backup and

 

 

 

 

remote management.

 

 

 

 

 

 

Security features

Provides support for VPNs4, Cisco IOS Firewall, and IPsec5.

All models

All models

 

 

Additionally, the Cisco 880 series routers also provide URL

 

 

 

 

filtering.

 

 

 

 

 

 

 

Embedded

 

Provides 802.11n connectivity. The radio is backward

Wireless models

Wireless models

wireless access

 

compatible with 802.11b/g.

 

 

point

 

 

 

 

 

 

 

 

 

FE WAN port

 

Provides connection to 10/100BASE-T.Can be connected to

861 models

881 models

 

 

other network devices, such as a cable modem, an xDSL6

 

 

 

 

modem, or router. The router is capable of bridging and

 

 

 

 

multiprotocol routing between the LAN and WAN ports.

 

 

 

 

 

 

 

Battery

 

Provides nonvolatile date and time when the router is

All models

backed-up

 

powered on. The RTC is used for verifying the validity of the

 

 

Real-timeclock

 

Certification Authority stored on the router.

 

 

(RTC)

 

 

 

 

 

 

 

 

 

USB port

 

Supports high-speedUSB 1.1. Provides connection for USB

All models

 

 

devices such as security tokens and flash memory.

 

 

 

 

 

 

 

PoE7

 

(Optional) Provides power for devices (such as phones) that

Models with PoE

 

 

are connected to the router.

 

 

 

 

 

 

 

G.SHDSL8 port

 

Provides 2-wireor4-wireconnection to a G.SHDSL

888 models

 

 

network.

 

 

 

 

 

 

 

3G9 card slot

 

Provides backup data link.

3G models

Dying gasp

 

Detects when the router is about to lose power, and sends a

xDSL models

 

 

power-failsignal to warn the DSLAM10 about the

 

 

 

 

impending line drop.

 

 

 

 

 

 

 

Data BRI port

 

Provides backup and remote management functions by

xDSL models,

 

 

connecting to the ISDN service provider if the main

 

except for the 3G

 

 

G.SHDSL link fails.

 

and SRST11 models

FXO12 port

 

An FXO interface connects local calls to a central office or

881 SRST models

 

 

PBX. This is the interface a standard telephone provides.

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-14

OL-16193-01

Chapter 1 Product Overview

Hardware Features

Table 1-3

Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued)

 

 

 

 

 

Feature

 

Description

860 Series

880 Series

 

 

 

 

 

FXS13/DID14

 

An FXS interface connects directly to a standard telephone,

SRST models

port

 

a fax machine, or similar device. This interface supplies

 

 

 

 

ringing voltage and dial tone to the station.

 

 

 

 

 

 

 

BRI voice port

 

The ISDN BRI S/T voice interface provides a client-side

SRST models

 

 

(TE) ISDN S/T physical interface for connection to an NT1

 

 

 

 

device that terminates an ISDN telephone network.

 

 

 

 

 

 

 

1.FE = Fast Ethernet.

2.MDI = media-dependentinterface in normal mode.

3.MDIX = media-dependentinterface in crossover mode.

4.VPN = Virtual Private Network.

5.IPsec = IP security.

6.xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

7.PoE = Power over Ethernet.

8.G.SHDSL = (global industry standard) symmetrical high-speedDSL.

9.3G = Third-Generation.

10.DSLAM = digital subscriber line access multiplexer.

11.SRST = Survivable Remote Site Telephony.

12.FXO = Foreign Exchange Office.

13.FXS = Foreign Exchange Station.

14.DID = Direct Inward Dialing.

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

1-15

 

 

 

 

 

Chapter 1 Product Overview

Hardware Features

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

1-16

OL-16193-01

C H A P T E R 2

Installing the Router

This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series and Cisco 880 series integrated services routers (ISRs), and contains the following sections:

Equipment, Tools, and Connections, page 2-1

Installing the Router, page 2-3

Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmapthat ships with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.

Equipment, Tools, and Connections

This section describes the equipment, tools, and connections necessary for installing your Cisco 860 series and Cisco 880 series ISRs.

Items Shipped with your Router

Unpack the box and verify that all items listed on the invoice have been shipped with the router.

Table 2-1 lists the items and their quantities that are shipped with each router model.

Table 2-1

Items and Their Quantities That Are Shipped with the Cisco 860 Series And Cisco 880

 

Series ISRs

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series

Cisco 880 Series

Item

 

Routers

Routers

 

 

 

 

RJ-45–to–RJ-45Ethernet cable1

1

1

 

DSL2 cable3

 

1

1

 

RJ-45–to–DB-9console cable

1

1

 

 

 

 

 

External 60-Wpower supply adapter

1

1

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

2-1

 

 

 

Chapter 2 Installing the Router

Equipment, Tools, and Connections

Table 2-1

Items and Their Quantities That Are Shipped with the Cisco 860 Series And Cisco 880

 

Series ISRs (continued)

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series

Cisco 880 Series

Item

 

Routers

Routers

 

 

 

 

Power supply cable

1

1

 

 

 

 

 

Cisco Configuration Professional (CCP) CD4

1

1

 

1.Cisco 861 and Cisco 881 ISRs only.

2.DSL = digital subscriber line.

3.Cisco 888 ISRs only.

4.Some SKUs do not include CCP.

Additional Items

The following items are not shipped with the router, but are required for installation:

ESD-preventivecord and wrist strap.

Screws for mounting the router on a wall:

Two number-10wood screws (roundorpan-head)withnumber-10washers, or twonumber-10washer-headscrews, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 in. (20 mm) into the supporting wood or metal wall stud.

Two number-10wall anchors with washers, for mounting the router on ahollow-wall.

Wire crimper for chassis grounding.

Wire for connecting the chassis to an earth ground:

AWG 14 (2 mm2) or larger wire forNEC-compliantchassis grounding.

AWG 18 (1 mm2) or larger wire for EN/IEC60950–compliantchassis grounding.

A ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliantchassis grounding.

Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.

Connections

Obtain a broadband or Ethernet connection from your service provider.

Ethernet Devices

Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.

If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.

If you plan to connect a modem, provide the modem and modem cable.

If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.

If you plan to use the cable-lockfeature, provide a Kensington or equivalent locking cable.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-2

OL-16193-01

 

 

Chapter 2 Installing the Router

Installing the Router

Installing the Router

Warning

Warning

Warning

Caution

Caution

This section describes how to install the Cisco 860 series and Cisco 880 series ISRs. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall.

This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242

This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 248

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could occur and cause damage to the router.

Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis.

Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.

Installing on a Table

To install the router on a table or other flat horizontal surface, firmly place the router on a table, or other horizontal surface. Keep at least 1 in. (2.5 cm) of clear space beside the cooling inlet and exhaust vents.

Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-6.

Mounting on a Wall

The Cisco 860 series and Cisco 880 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface.

Note The mounting holes are bidirectional. You can hang the router with the LEDs either facing you or facing away from you.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

2-3

 

 

 

Chapter 2 Installing the Router

Installing the Router

Tip When choosing a location forwall-mountingthe router, consider cable limitations and wall structure.

To mount the router on the wall, follow these steps:

Step 1 Anchor the screws into the wall, leaving 1/8 in. (0.32 cm) between the screw head and the wall.Figure 2-1 shows thewall-mountholes located on the underside of the router.

Figure 2-1Wall-mountHoles on the Underside of the Router

8.200 in.

3.673 in.

 

1

1

 

 

5.961 in.

 

231987

1 Wall-mountholes

Step 2 Hang the router on the screws, and place the power adapter on a nearby horizontal surface. SeeFigure 2-2.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-4

OL-16193-01

 

 

Chapter 2 Installing the Router

Installing the Router

Figure 2-2Router Mounted on the Wall

1

1

4

2

 

 

 

 

 

231982

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

1

Two number-10wood screws mounted on the

3

Horizontal surface on which to place the

 

wall

 

power adapter

 

 

 

 

 

 

2

Wall-mountholes

4

Distance between the screw head and the wall,

 

 

 

1/8 in. (0.32 cm)

 

 

 

 

 

 

Step 3 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the“Installing the Router Ground Connection” section on page 2-6.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

2-5

 

 

 

Chapter 2 Installing the Router

Installing the Router

Installing the Router Ground Connection

The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards.

For NEC-compliantgrounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm).

For EN/IEC 60950–compliantgrounding, use size 18 AWG (1 mm2) or larger copper wire.

To install the ground connection, follow these steps:

Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal.

Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper.

Step 3 Attach the ground lug or ring terminal to the chassis as shown inFigure 2-3.For a ground lug, use the provided two screws with captive locking washers. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10in-lb(0.9 to 1.1N-m).

Figure 2-3Chassis Ground Connection Using Ring Terminal

231981

1

1 Ring Terminal

Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site.

After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

2-6

OL-16193-01

 

 

C H A P T E R 3

Connecting the Router

Note

Note

Note

This chapter describes how to connect Cisco 860 series and Cisco 880 series integrated services routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and the network. The chapter contains the following sections:

Preparing to Connect the Router, page 3-2

Connecting a PC, Server, or Workstation, page 3-3

Connecting a Phone, page 3-4

Connecting an External Ethernet Switch, page 3-5

Connecting a Terminal or PC to the Console Port, page 3-6

Connecting a Data BRI Port, page 3-7

Connecting an FE Line—FE4 WAN Port, page 3-9

Connecting a G.SHDSL Line—G.SHDSL Port, page 3-10

Connecting Power over Ethernet, page 3-11

Connecting the AC Adapter, page 3-11

Connecting an FXS line, page 3-14

Connecting a FXO Line, page 3-16

Connecting a Voice ISDN BRI Line, page 3-17

Verifying Connections, page 3-19

For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmapthat ships with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.

The illustrations in this chapter show a wireless router with antennas attached. Nonwireless routers do not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and nonwireless routers.

Depending on the features available for your router, some content in this chapter may not apply to your router.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

3-1

 

 

 

Chapter 3 Connecting the Router

Preparing to Connect the Router

Preparing to Connect the Router

Before you connect the router to the devices, install the router according to the instructions in Chapter 2, “Installing the Router.”

Preventing Damage to the Router

To prevent damage to your router, follow these guidelines when connecting devices to your router:

Turn off power to the devices and to the router until all connections are completed.

Caution Do not turn on the devices until after you have completed all connections to the router.

Connect the color-codedcables supplied by Cisco Systems to thecolor-codedports on the back panel.

If you must supply your own cable, see Appendix A, “Technical Specifications,” for cabling specifications. If this appendix does not provide specifications for a particular cable, we strongly recommend ordering the cable from Cisco Systems.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-2

OL-16193-01

 

 

Chapter 3 Connecting the Router

Connecting a PC, Server, or Workstation

Connecting a PC, Server, or Workstation

To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:

Step 1 Connect one end of the yellow Ethernet cable to a Ethernet switch port on the router.Figure 3-1 shows a Cisco 888W router connected to a PC.

Figure 3-1Connecting a Server, PC, or Workstation

1

231989

1

Yellow Ethernet cable

3

RJ-45port on the network interface card

 

 

 

(NIC)

 

 

 

 

2

Ethernet switch port on the router

 

 

 

 

 

 

Step 2 Connect the other end of the cable to theRJ-45port on the network interface card (NIC) installed in the PC, server, or workstation.

Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.

Note Use the Cisco Configuration Express to configure the Internet connection settings. See the

Cisco Configuration Professional Quick Start Guide for more information.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

3-3

 

 

 

Chapter 3 Connecting the Router

Connecting a Phone

Connecting a Phone

To connect a phone to an Ethernet switch port, follow these steps:

Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router.Figure 3-2 shows a Cisco 888W router connected to a phone.

Figure 3-2Connecting a Phone

2

270551

 

1

1 2 3

4 5 6

7 8 9

*0 #

1

Yellow Ethernet cable

3

RJ-45port on a phone

 

 

 

 

2

Ethernet switch port 1 on the router

 

 

 

 

 

 

Step 2 Connect the other end of the cable to theRJ-45port on the phone.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-4

OL-16193-01

 

 

Chapter 3 Connecting the Router

Connecting an External Ethernet Switch

Connecting an External Ethernet Switch

If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the router’s Ethernet switch.

To connect an external Ethernet switch to an Ethernet switch port on the router, perform the following steps:

Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router.

Figure 3-3 shows a Cisco 888W router connected to an Ethernet switch.

Figure 3-3Connecting to an Ethernet Switch

1

2

1

Catalyst 3500

SERIES

2

XL

INLINE POWER

231986

1

Ethernet switch port on the router

2

Available port on the external Ethernet switch

 

 

 

 

3

Yellow Ethernet cable, RJ-45–to–CAT-5,

 

 

 

connecting to an external Ethernet switch

 

 

 

port.

 

 

 

 

 

 

Step 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet connections.

Step 3 Turn on the Ethernet switch.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

3-5

 

 

 

Chapter 3 Connecting the Router

Connecting a Terminal or PC to the Console Port

Connecting a Terminal or PC to the Console Port

Connect a terminal or PC to the Console Aux port either to configure the software by using the command-lineinterface (CLI) or to troubleshoot problems with the router.

To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:

Step 1 Connect theRJ-45end of aDB-9–to–RJ-45serial cable to theRJ-45Console Aux port on the router.Figure 3-4 shows theRJ-45end of the serial cable connected to the Console Aux port on the router.

Figure 3-4Connecting a Terminal or PC to the Console Port

FE0

FE1

FE2

FE3

1

231990

2

1

RJ-45connector to the Console Aux port on

2

DB-9connector

 

the router

 

 

 

 

 

 

Step 2 Connect theDB-9end of theDB-9–to–RJ-45serial cable to the to the COM port on your laptop or PC.

Note Some laptops and personal computers do not come withDB-9serial port connectors and may use aUSB-to-serialport adapter.

Step 3 To communicate with the router, start a terminal emulator application.

Terminal Emulator Settings

Use the following settings for the terminal emulator connection:

9600 baud

8 data bits, no parity

1 stop bit

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-6

OL-16193-01

 

 

Chapter 3 Connecting the Router

Connecting a Data BRI Port

no flow control

When the terminal emulator establishes communications, the router prompt is displayed.

For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections.

Connecting a Data BRI Port

You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in case the primary xDSL (general term referring to various forms of DSL, including [global industry standard] symmetrical high-speedDSL [G.SHDSL]) WAN service fails. The Data BRI connection is not available on thethird-generation(3G) models.

The cabling requirements for the ISDN S/T connection are as follows:

You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the splitter, and the second cable connects the splitter to the wall jack.

There are RJ-45connectors at both ends of the default orange ISDN S/T cable. However, anRJ-45–to–RJ-11ISDN S/T cable is available upon request if the wall jack at the site requires anRJ-11connector. Contact your router reseller for the appropriate cable.

Caution Both LAN and WAN ports useRJ-45connectors. Use caution when connecting cables to these connectors. To avoid damage to the router, do not connecttelephone-networkvoltage (TNV) circuits (such as ISDN or DSL circuits) to safetyextra-lowvoltage (SELV) circuits (such as LAN circuits).

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

3-7

 

 

 

Chapter 3 Connecting the Router

Connecting a Data BRI Port

Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port.

To connect the Data BRI port to the ISDN service provider, follow these steps:

Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router.Figure 3-5 shows a Data BRI connection.

Figure 3-5Connecting the Data BRI Port to the ISDN Line

2

5

3

4

231991

6 7

8

 

 

 

 

1

End of the ISDN S/T cable, which connects to

5

xDSL splitter (provided by the xDSL service

 

 

 

 

 

the Data BRI port on the router

 

provider)

 

 

 

 

 

 

 

 

 

 

 

 

2

Network termination 1 (NT1) box

6

Other end of the first unshielded Category 5

 

 

 

 

 

 

 

cable, which connects to the telephone line

 

 

 

 

 

 

 

port on the splitter

 

 

 

 

 

 

 

 

 

 

 

 

3

Other end of the ISDN S/T cable, which

7

One end of the second unshielded Category 5

 

 

 

 

 

connects to the S/T port on the NT1 box

 

cable, which connects to the

 

 

 

 

 

 

 

telecommunication service port on the splitter

 

 

 

 

 

 

 

 

 

 

 

 

4

One end of the first unshielded Category 5

8

Other end of the second unshielded

 

 

 

 

 

cable, which connects to the U port on the

 

Category 5 cable, which connects to the wall

 

 

 

 

 

NT1 box

 

jack

 

 

 

 

 

 

 

 

 

 

 

Step 2

Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box.

 

 

 

Step 3

Connect the first unshielded Category 5 cable from the U port on the NT1 box to the telephone line port

 

 

 

 

on the splitter.

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

3-8

 

 

 

 

 

OL-16193-01

 

 

 

 

 

 

 

 

Chapter 3 Connecting the Router

Connecting an FE Line—FE4WAN Port

Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider.

Connecting an FE Line—FE4WAN Port

To connect the Fast Ethernet (FE) 4 WAN port on the router, follow these steps:

Step 1 Connect one end of the yellow cable to the Ethernet FE4 WAN port.Figure 3-6 shows an FE4 WAN port connection.

Figure 3-6Connecting the FE4 WAN Port

1

WAN

1

2

231992

3

Internet

1

FE4 WAN port

3

Modem, which connects to the Internet

 

 

 

 

2

WAN connection to the Internet

 

 

 

 

 

 

Step 2 Connect the other end of cable to an available port on the modem.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

3-9

 

 

 

Chapter 3 Connecting the Router

Connecting a G.SHDSL Line—G.SHDSLPort

Note Follow the instructions from your Internet service provider to determine which modem port to use.

Connecting a G.SHDSL Line—G.SHDSLPort

To connect the router to a (global industry standard) symmetrical high-speedDSL (G.SHDSL) line, follow these steps:

Step 1 Connect one end of the lavender DSL cable to the G.SHDSL port on the router. SeeFigure 3-7.

Figure 3-7Connecting the G.SHDSL Line

2

 

232175

1 G.SHDSL port on the router

2 DSL wall jack

Step 2 Connect the other end of the cable to the DSL wall jack.

Note The DSL line must have been provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. If the G.SHDSL CD LED is not on, check with your DSL service provider.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-10

OL-16193-01

Chapter 3 Connecting the Router

Connecting Power over Ethernet

Connecting Power over Ethernet

Figure 3-8 shows how to connect the48-VDCPower over Ethernet (PoE) power adapter in your Cisco 880 series ISR to an AC power outlet. The PoE provides power to port 0 and port 1 of the4-port10/100 FastEthernet switch.

Note The router should also be connected to an AC power outlet through a12-Vadapter. To connect the router to an AC outlet, see“Connecting the AC Adapter” section on page 3-11.

Figure 3-8

Connecting PoE

1

4

2

5

3

 

 

2

4

6

231995

1

PoE input jack

4

AC plug

 

 

 

 

2

Power cord

5

DC plug

 

 

 

 

3

Power adapter—48VDC

6

Power adapter—60W, 12 VDC

 

 

 

 

Connecting the AC Adapter

Warning The device is designed to work with TN power systems.Statement 19

Warning This product relies on the building’s installation forshort-circuit(overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on the phase conductors (allcurrent-carryingconductors). The fuse or circuit breaker must have adequate safety approvals recognized by the country of usage.Statement 119

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

3-11

 

 

 

 

 

Chapter 3 Connecting the Router

Connecting the AC Adapter

To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps:

Step 1 Connect the router to an AC power outlet as shown inFigure 3-9.

Figure 3-9Connecting the AC Adapter

1

2

4

3

231996

1

DC plug

3

Power adapter—60W, 12 VDC

 

 

 

 

2

Power cord

4

AC plug

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-12

OL-16193-01

Chapter 3 Connecting the Router

Connecting the AC Adapter

Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the end of the DC plug. SeeFigure 3-10.

Figure 3-10Securing the Power Cord

3

2 4 1

270659

1

Power lock clip

2

Power cord

 

 

 

 

3

DC plug

4

Holes on either side of the power connector

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

3-13

 

 

 

 

 

Chapter 3 Connecting the Router

Connecting an FXS line

Step 3 Snap the latches into the holes on either side of the power connector. SeeFigure 3-11.

Figure 3-11Power Lock Clip Latched Into the Holes on Either Side of the Power Connector

1

2

4

3

270800

1

Power lock clip

2

Power cord

 

 

 

 

3

Power adapter

4

AC plug

 

 

 

 

 

 

 

 

Connecting an FXS line

Use a standard straight-throughRJ-11modular telephone cable to connect an Foreign Exchange Service (FXS) port to a telephone or fax machine.

Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch theRJ-11(phone) port wires (conductors), the conductors of a cable connected to theRJ-11port, or the associatedcircuit-boardwhen the ringer is active. The ringer is activated by an incoming call.

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: FXS.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-14

OL-16193-01

Chapter 3 Connecting the Router

Connecting an FXS line

To connect the FXS line, follow these steps:

Step 1 Connect one end of thestraight-throughRJ-11cable to the FXS port.Figure 3-12 shows an FXS line connection.

Figure 3-12Connecting an FXS Line

1

2

3

241907

Fax machine or telephone

1 FXS port

3 RJ-11port

2 RJ-11cable

Step 2 Connect the other end of the cable to theRJ-11port on the telephone or fax machine.

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

3-15

 

 

 

 

 

Chapter 3 Connecting the Router

Connecting a FXO Line

Connecting a FXO Line

Use a straight-throughRJ-11cable to connect the Foreign Exchange Office (FXO) voice port to the PSTN or PBX through a telephone wall outlet.

To connect the FXO line, follow these steps:

Step 1 Connect one end of thestraight-throughRJ-11cable to the FXO port. SeeFigure 3-13.

Figure 3-13Connecting an FXO line

2

1

 

 

3

 

 

270542

1

FXO port

3 Telephone outlet

2

RJ-11cable

 

Step 2 Connect the other end of the cable to anRJ-11telephone wall outlet.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-16

OL-16193-01

Chapter 3 Connecting the Router

Connecting a Voice ISDN BRI Line

Connecting a Voice ISDN BRI Line

Use a straight-throughRJ-45cable to connect the Voice Basic Rate Interface (BRI) port to the ISDN network through a telephone wall outlet or other device.

Caution To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only, and not to any otherRJ-45connector.

To connect the Voice BRI line, follow these steps:

Step 1 Connect one end of astraight-throughRJ-45–to–RJ-45cable to the Voice BRI port.

Note When the interface is configured as NT and is connecting to a TE device, use a crossover cable. SeeTable A-7.

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

OL-16193-01

 

 

3-17

 

 

 

 

 

Chapter 3 Connecting the Router

Connecting a Voice ISDN BRI Line

Figure 3-14 shows a Voice BRI line connection.

Figure 3-14Connecting a Voice BRI Line

1

2

3

241906

1 Voice BRI port

3 Wall jack

2 RJ-45cable

Step 2 Connect the other end of the cable to theRJ-45wall outlet or other device.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-18

OL-16193-01

Chapter 3 Connecting the Router

Verifying Connections

Verifying Connections

To verify that all devices are properly connected to the router, first turn on all the connected devices. Then check the LEDs. To verify router operation, refer to Table 3-1 .

For full LED description see Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs.

Table 3-1

Verifying the Router Operation

 

 

 

 

 

 

 

 

 

 

Power and Link

 

LEDs to Check

Normal Patterns

 

 

 

 

 

 

Power

 

OK

On when power is supplied to router.

 

 

 

 

 

 

To servers, PCs,

 

LAN 0, LAN 1, LAN 2, or LAN 3

On when the FE LAN port is physically connected to a

 

workstations, or an

 

server, PC, workstation, or external Ethernet switch.

 

external Ethernet switch

 

 

 

 

 

 

connected to the LAN

 

 

 

 

 

 

ports (FE10, FE1, FE2,

 

 

 

 

 

 

or FE3)

 

 

 

 

 

 

 

 

 

 

 

 

To FE WAN line

 

WAN FE4

On when the WAN Ethernet carrier has detected status.

 

 

 

 

Blinks when receiving or transmitting data.

 

 

 

 

 

 

To xDSL2 line

 

xDSL CD

Green when the line is connected to the xDSL DSLAM3.

 

 

 

xDSL Data

Green when receiving or sending data.

 

 

 

 

 

 

To ISDN line

 

Data BRI LNK

Green when the ISDN line is connected.

 

 

 

 

 

 

 

 

Data BRI B1 and B2

Green when the channel is connected.

 

 

 

 

 

 

3G4

 

WWAN5

Green when service is established.

 

 

 

 

Slow blinking when searching for service.

 

 

 

 

 

 

 

 

RSSI6

Amber when service is not established.

 

 

 

 

Green when signal strength is high.

 

 

 

 

Off or slow blinking when signal strength is low.

 

 

 

 

Fast blinking when signal strength is medium.

 

 

 

 

 

 

 

 

CDMA7

Green when service is established.

 

 

 

GSM8

Green when service is established.

 

To PPP9 clients

 

PPP

Green when either a PPPoE10 or PPPoA11 client is running.

 

To VPN12 tunnel

 

VPN

Green when a crypto session is running.

 

To wireless LAN

WLAN LINK

Wireless LAN link status:

 

 

 

 

Green if at least one client is associated.

 

 

 

 

Off if no client is associated.

 

 

 

 

 

 

 

 

WLAN 2.4 GHz

Wireless LAN 2.4-GHzstatus:

 

 

 

 

Green when radio is connected, SSID13 is configured,

 

 

 

 

signal is being transmitted, and client is associated.

 

 

 

 

Slow blinking when radio is connected, SSID is

 

 

 

 

configured, and signal is being transmitted.

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-16193-01

 

 

 

 

3-19

 

 

 

 

 

 

 

Chapter 3 Connecting the Router

Verifying Connections

Table 3-1

Verifying the Router Operation (continued)

 

 

 

 

 

Power and Link

 

LEDs to Check

Normal Patterns

 

 

 

 

PoE14

 

PoE 0

Green when connected and powered.

 

 

PoE 1

Amber when there is a fault with the inline power supply.

 

 

 

 

1.FE = Fast Ethernet.

2.xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL.

3.DSLAM = digital subscriber line access multiplexer.

4.3G = Third-Generation.

5.WWAN = wireless WAN.

6.RSSI = Received Signal Strength Indicator.

7.CDMA = code division multiple access.

8.GSM = Global System for Mobile Communication.

9.PPP = Point-to-PointProtocol.

10.PPPoE = PPP over Ethernet.

11.PPPoA = PPP over ATM.

12.VPN = Virtual Private Network.

13.SSID = Service Set Identifier.

14.PoE = Power over Ethernet.

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

3-20

OL-16193-01

C H A P T E R 4

Initial Configuration

This chapter provides instructions for initial configuration of the Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). For initial configuration, we recommend using

Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-basedgraphical user interface that guides you through initial configuration.

You may also initially configure your router by using the Cisco IOS command-lineinterface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network.

This chapter contains the following sections:

Cisco Configuration Professional Express, page 4-1

Cisco IOS CLI, page 4-1

Setup Command Facility, page 4-3

Verifying the Initial Configuration, page 4-5

Initial Configuration of the Wireless Access Point, page 4-5

Note Some SKUs may not include a default configuration file. If your router does not have a default configuration file, go to the“Setup Command Facility” section on page 3 to configure the initial router settings.

Cisco Configuration Professional Express

After you connect cables and power up the router, we recommend that you use the Cisco CP Express web-basedapplication to configure the initial router settings.

For instructions on how to use Cisco CP Express to configure the router see the Cisco CP Express User’s Guide.

Cisco IOS CLI

To configure the initial router settings by using the Cisco IOS CLI, you will need to set up a console connection. For instructions on how to setup a console connection, see the “Connecting a Terminal or PC to the Console Port” section on page 3-6.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

4-1

 

 

 

Chapter 4 Initial Configuration

Cisco IOS CLI

To configure the initial router settings using Cisco IOS CLI, follow these steps:

Step 1 Set up a console connection to your router. The following message is displayed:

...

router con0 is now available

Step 2 PressReturn orEnter. The following message is displayed:

Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-timeuse of the username "cisco"

with the password "cisco." The default username and password have a privilege level of 15.

Please change these publicly known initial credentials using Cisco CP Express or the Cisco IOS CLI.

Here are the Cisco IOS commands.

username <myuser> privilege 15 secret 0 <mypassword> no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use.

For more information about Cisco CP please follow the instructions in the QUICK START

GUIDE for your router...

...

User Access Verification

Username:

Step 3 Enter the usernamecisco and pressReturn orEnter. The following prompt is displayed:

Password:

Step 4 Enter the passwordcisco and pressReturn orEnter. The following prompt is displayed:

Router#

A message is displayed that is similar to the first warning message. The message directs you to change the username and password.

You are now in privileged EXEC mode.

Note You must change the username and password before you log off the router. You cannot use the usernamecisco or passwordcisco after you log off from this session.

Step 5 To change the username and password, enter the following at the prompt:

username username privilege 15 secret 0password

Username andpassword are the username and password that you wish to use.

To continue using Cisco IOS CLI for initial configuration, see the applicable configuration procedures in the Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide.

Note Save your configuration changes regularly to avoid losing them during resets, power cycles, or power outages. Use thecopy running-config startup-config command at the privileged EXEC mode prompt (Router#) to save the configuration to NVRAM.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

4-2

OL-16193-01

 

 

Chapter 4 Initial Configuration

Setup Command Facility

Step 6 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.

Setup Command Facility

The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network.

To use the setup command facility, you will need to set up a console connection with the router and enter the privileged EXEC mode.

Note For instructions on how to set up a console connection see the“Connecting a Terminal or PC to the Console Port” section on page 3-6.

To configure the initial router settings with setup command facility, follow these steps:

Step 1 Set up a console connection to your router and enter privileged EXEC mode. For instructions on how to enter privileged EXEC mode seeStep 1 throughStep 4 in the“Cisco IOS CLI” section on page 4-1 section.

Step 2 In privileged EXEC mode, at the prompt, entersetup.

yourname# setup

The following message is displayed:

---System Configuration Dialog---

Continue with configuration dialog? [yes/no]:

You are now in setup command facility.

The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. PressCtrl-C,and enter thesetup command at the privileged EXEC mode prompt (Router#). For more information on using the setup command facility, seeThe Setup Command chapter inCisco IOS Configuration Fundamentals Command Reference, Release 12.2T.

Step 3 To proceed using the setup command facility, enteryes:

Continue with configuration dialog? [yes/no]: yes

Step 4 When the following messages appear, enteryes to enter basic management setup:

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

4-3

 

 

 

Chapter 4 Initial Configuration

Setup Command Facility

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

Step 5 Enter a hostname for the router (this example uses Router):

Configuring global parameters:

Enter host name [Router]: Router

Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.

The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.

Enter enable secret: xxxxxx

Step 7 Enter an enable password that is different from the enable secret password. This password isnot encrypted (less secure) and can be seen when viewing the configuration.

The enable password is used when you do not specify an

enable secret password, with some older software versions, and some boot images.

Enter enable password: xxxxxx

Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:

The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx

Step 9 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]:

Community string [public]:

A summary of the available interfaces is displayed.

Step 10 Choose one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the

management network from the above interface summary: fastethernet4

Step 11 Respond to the following prompts as appropriate for your network:

Configuring interface FastEthernet0:

Use the 100 Base-TX(RJ-45)connector? [yes]:yes

Operate in full-duplexmode? [no]:yes

Configure IP on this interface? [yes]: yes

IP address for this interface: 172.1.2.3

Subnet mask for this interface [255.255.0.0] : 255.255.0.0

Class B network is 172.1.0.0, 26 subnet bits; mask is /16

The configuration is displayed:

The following configuration command script was created:

 

 

 

hostname

Router

 

 

 

 

 

enable secret 5

$1$D5P6$PYx41/lQIASK.HcSbfO5q1

 

 

 

enable password xxxxxx

 

 

 

line vty

0 4

 

 

 

 

 

password

xxxxxx

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

4-4

 

 

 

OL-16193-01

 

 

 

 

 

 

Chapter 4 Initial Configuration

Verifying the Initial Configuration

snmp-servercommunity public

!

no ip routing

!

interface FastEthernet0 no shutdown

speed 100 duplex auto

ip address 172.1.2.3 255.255.0.0

!

Step 12 Respond to the following prompts. Enter2 to save the initial configuration.

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]: 2

Building configuration...

Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

The user prompt is displayed.

Router>

Step 13 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for verification procedures.

After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration.

Verifying the Initial Configuration

To verify that the new interfaces are operating correctly, perform the following tests:

To verify that the interfaces and line protocol are in the correct state—upordown—entertheshow interfaces command.

To display a summary status of the interfaces configured for IP, enter the show ip interface brief command.

To verify that you configured the correct hostname and password, enter the show configuration command.

After you complete and verify the initial configuration, you can configure your Cisco router for specific functions.

Initial Configuration of the Wireless Access Point

The embedded wireless access point (AP) runs its own IOS. You can initially configure the embedded wireless AP using one of the following methods:

Cisco Configuration Professional (CP) Express

Setup command facility on the embedded wireless device

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

4-5

 

 

 

Chapter 4 Initial Configuration

Initial Configuration of the Wireless Access Point

For information on how to do basic wireless configuration on your router see the Basic Wireless Device chapter of theCisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

4-6

OL-16193-01

 

 

A P P E N D I X A

Technical Specifications

This appendix provides router, port, and cabling specifications for Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). It contains the following sections:

Router Specifications, page A-1

Wireless Access Point, page A-2

LAN Port Pinouts, page A-3

Console Port Connector Pinouts, page A-3

G.SHDSL Port Connector Pinouts, page A-3

Data BRI Port Connector Pinouts, page A-4

Voice ISDN BRI Interface Pin Numbers and Functions, page A-4

Cable Specifications, page A-5

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmapthat was shipped with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.

Router Specifications

Table A-1 lists the system specifications for the routers.

Table A-1

Router Specifications

 

 

 

 

Description

 

Design Specification

 

 

Physical Dimensions

 

 

 

Dimensions with antenna and rubber feet

1.9 x 12.8 x 10.4 in.

(H x W x D)

 

 

 

Weight (not including desktop power supply)

5.5 lb (2.5 kg) maximum

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

A-1

 

Appendix A Technical Specifications

Wireless Access Point

Table A-1

Router Specifications

 

 

 

 

Description

 

Design Specification

 

 

Environmental Operating Ranges

 

 

 

Nonoperating temperature

–4to 149°F(–20to 65°C)

 

 

Nonoperating humidity

5 to 95% relative humidity

 

 

Nonoperating altitude

0 to 15,000 ft (4570 m)

 

 

Operating temperature

32 to 104°F (0 to 40°C)

 

 

Operating humidity

10 to 85% relative humidity

 

 

Operating altitude

0 to 10,000 ft (3000 m)

 

 

Noise criterion

NC33; less than or equal to 32 dBA

 

 

Router Power Adapter

 

 

 

Input voltage

85 to 264 VAC

 

 

Input frequency

47 to 63 Hz

 

 

Power output

60 W maximum

 

 

Output voltages

+12 VDC

 

 

Inline Power-over-EthernetAdapter

 

 

 

Input voltage

85 to 264 VAC

 

 

Input frequency

47 to 63 Hz

 

 

Power output

80W maximum

 

 

Output voltage

–48VDC

 

 

 

Wireless Access Point

Table A-2 lists the specifications for the wireless access point (AP).

Table A-2Wireless Access Point Specifications

Description

Design Specification

 

 

Radio technology

IEEE 802.11n draft 2.0 standard compliant. 2x3

 

MIMO radio. Backward compatible with

 

802.11b/g.

 

 

Operating frequency

2.4-GHzradio band

 

 

Channels

Country-specific20 and 40 MHz

 

 

PHY Data rate

802.11b up to 11 Mbps

 

802.11g up to 54 Mbps

 

802.11n up to 300 Mbps

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

A-2

OL-16193-01

 

 

 

Appendix A Technical Specifications

LAN Port Pinouts

LAN Port Pinouts

Table A-3 provides pinouts for the Ethernet LAN port.

Table A-3

Ethernet LAN Port Pinouts

 

 

 

Pin

 

Function

 

 

 

1

 

RX+

 

 

 

2

 

RX–

 

 

 

3

 

TX+

 

 

 

4

 

Unused

 

 

 

5

 

Unused

 

 

 

6

 

TX–

 

 

 

7

 

Unused

 

 

 

8

 

Unused

 

 

 

Console Port Connector Pinouts

Table A-4 provides pinouts for the console connector (for connecting a terminal or PC).

Table A-4

Console Connector Pinouts (RJ-45-to-DB-9)

 

 

 

 

RJ-45Pin

 

Function

 

 

 

 

1

 

RTS

 

 

 

 

2

 

DTR

 

 

 

 

3

 

TXD

 

 

 

 

4

 

GND

 

 

 

 

5

 

GND

 

 

 

 

6

 

RXD

 

 

 

 

7

 

DSR

 

 

 

 

8

 

CTS

 

 

 

 

G.SHDSL Port Connector Pinouts

Table A-5 provides pinouts for the (global industry standard) symmetricalhigh-speedDSL (G.SHDSL) WAN port.

 

 

Table A-5

G.SHDSL WAN Port Pinouts

 

 

 

 

 

 

 

 

Pin

 

Function

 

 

 

 

 

1

 

Unused

 

 

 

 

 

2

 

TIP (Port1)

 

 

 

 

 

 

 

 

 

 

 

 

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

 

 

 

 

 

 

 

OL-16193-01

 

 

 

 

A-3

 

 

 

 

 

 

 

Appendix A Technical Specifications

Data BRI Port Connector Pinouts

Table A-5

G.SHDSL WAN Port Pinouts

 

 

 

Pin

 

Function

 

 

 

3

 

TIP (Port0)

 

 

 

4

 

TIP (Port0)

 

 

 

5

 

TIP (Port1)

 

 

 

6

 

Unused

 

 

 

Data BRI Port Connector Pinouts

Table A-6 provides pinouts for the Data BRI port.

Table A-6

Data BRI Port Pinouts

 

 

 

Pin

 

Function

 

 

 

1

 

Unused

 

 

 

2

 

Unused

 

 

 

3

 

TXP

 

 

 

4

 

RXP

 

 

 

5

 

TXN

 

 

 

6

 

TXN

 

 

 

7

 

Unused

 

 

 

8

 

Unused

 

 

 

Voice ISDN BRI Interface Pin Numbers and Functions

Table A-7 provides the interface pin numbers and functions for the voice ISDN BRI port.

Table A-7

Interface Pin Numbers and Functions

 

 

 

 

ISDN BRI NT/TE Card

NT Interface1

TE Interface2

Pin 3/T+

 

Pin 3/R+

Pin 3/T+

 

 

 

 

Pin 4/R+

 

Pin 4/T+

Pin 4/R+

 

 

 

 

Pin 5/R-

 

Pin 5/T-

Pin 5/R-

 

 

 

 

Pin 6/T-

 

Pin 6/R-

Pin 6/T-

 

 

 

 

1.Use a straight-throughcable for NT interfaces.

2.Use a crossover cable for TE interfaces.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

A-4

OL-16193-01

 

 

 

Appendix A Technical Specifications

Cable Specifications

Cable Specifications

This section provides specifications for the following Ethernet cables:

Straight-throughcable

Crossover cable

Because of the autocrossover (autosensing) function, both straight-throughand crossover cables can be used for the Ethernet LAN port.

Ethernet Cable Specifications

Table A-8 provides specifications that apply to bothstraight-throughand crossover Ethernet cables.

Table A-8

Ethernet Cable Specifications

 

 

 

Type

 

Category

 

 

 

10BASE-T

 

Category 3 or 5

 

 

 

100BASE-T

 

Category 5 or higher

 

 

 

Maximum Cable Length

The maximum length for the Ethernet cables that connect equipment to the router is 328 ft (100 m). This length is also the maximum distance between the router and the equipment connected to it.

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

OL-16193-01

A-5

 

Appendix A Technical Specifications

Cable Specifications

Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide

 

A-6

OL-16193-01