Cisco Systems ASR 1000 User Manual

0 (0)

Cisco ASR 1000 Series Aggregation

Services Routers Hardware Installation

and Initial Configuration Guide

November 2008

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 527-0883

Text Part Number: OL-13208-03

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0809R)

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

© 2008 Cisco Systems, Inc. All rights reserved.

 

 

 

 

 

C O N T E N T S

 

Preface xi

 

 

 

 

 

 

Document Revision History xi

 

 

 

 

 

Document Objectives

xii

 

 

 

 

 

Audience xii

 

 

 

 

 

 

Document Organization

xii

 

 

 

 

 

Safety Warnings and Cautions

xiii

 

 

 

 

Warning Definition

xiii

 

 

 

 

 

Related Documentation

xviii

 

 

 

 

 

Obtaining Documentation and Submitting a Service Request xix

 

Cisco ASR 1000 Series Routers Hardware Overview

 

C H A P T E R 1

1-1

 

Cisco ASR 1000 Series Routers

1-2

 

 

 

 

Cisco ASR 1000 Series Routers Features 1-2

 

 

 

Cisco ASR 1000 Series Routers Configurations 1-3

 

 

Field-Replaceable Units

1-4

 

 

 

 

 

Functional Overview 1-4

 

 

 

 

 

Chassis Slot and Logical Interface Numbering

1-5

 

 

Cisco ASR 1006 Router Slot Numbering

1-5

 

 

Cisco ASR 1004 Router Slot Numbering

1-7

 

 

Cisco ASR 1002 Router Slot Numbering

1-7

 

 

MAC Address Information

1-8

 

 

 

 

Online Insertion and Removal

1-9

 

 

 

Environmental Monitoring and Reporting Functions

1-10

 

Environmental Monitoring

1-10

 

 

 

Fan Failures

1-11

 

 

 

 

 

 

Reporting Functions

1-11

 

 

 

 

 

 

Cisco Product Identification Standard

1-15

 

 

 

 

 

Unique Device Identifier

1-16

 

 

 

 

 

 

Serial Number Label Location 1-17

 

Cisco ASR 1000 Series Routers Components 2-1

C H A P T E R 2

 

 

Cisco ASR 1000 Series Route Processor

2-1

 

 

 

 

 

Cisco ASR 1000 Series Route Processor Features 2-2

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

 

 

OL-13208-03

 

 

 

 

iii

 

 

 

 

 

 

 

Contents

 

How the Cisco ASR1000-RP1 Alarm LEDs Work

2-5

 

 

Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router 2-6

 

 

Cisco ASR 1000 Series Embedded Services Processors 2-9

 

 

Cisco ASR 1000 Series SPA Interface Processor

2-13

 

 

 

Shared Port Adapters 2-14

 

 

 

 

 

 

Cisco ASR 1000 Series Router Power Supplies 2-16

 

 

 

Power Supply Requirements for All Cisco ASR 1000 Series Routers 2-16

 

DC Power System Input Requirements for Cisco ASR 1000 Series Routers 2-17

 

AC and DC Power Supply Types

2-17

 

 

 

 

AC and DC System Power Ratings

2-17

 

 

 

 

Power Supplies for Cisco ASR 1006 Router

2-18

 

 

 

AC Power Supply LEDs and Connector for Cisco ASR 1006

2-18

 

DC Power Supply LEDs and Connectors for Cisco ASR 1006

2-21

 

Power Supplies for Cisco ASR 1004 Router

2-23

 

 

 

Cisco ASR 1004 AC Power Supply

2-23

 

 

 

 

Cisco ASR Router 1004 DC Power Supply

2-26

 

 

 

Power Supplies for Cisco ASR 1002 Router

2-28

 

 

 

Cisco ASR 1002 Router AC Power Supply

2-29

 

 

 

Cisco ASR 1002 Router DC Power Supply

2-31

 

 

 

Preparing Your Site for Installation 3-1

 

 

 

 

C H A P T E R 3

 

 

 

 

 

Safety Recommendations

3-2

 

 

 

 

 

 

Safety Warnings 3-2

 

 

 

 

 

 

 

Compliance Requirements

3-2

 

 

 

 

 

 

Cautions and Regulatory Compliance Statements for NEBS

3-3

 

 

Standard Warning Statements

3-4

 

 

 

 

 

General Safety Warnings

3-4

 

 

 

 

 

Site Planning 3-7

 

 

 

 

 

 

 

General Precautions

3-7

 

 

 

 

 

 

Site Selection Guidelines

3-8

 

 

 

 

 

 

 

Site Environmental Requirements

3-8

 

 

 

 

Physical Characteristics

3-8

 

 

 

 

 

 

Floor Loading Considerations

3-10

 

 

 

 

 

Site Power Guidelines

3-10

 

 

 

 

 

 

 

Electrical Circuit Requirements

3-10

 

 

 

 

Site Cabling Guidelines

3-12

 

 

 

 

 

 

 

Asynchronous Terminal Connections

3-13

 

 

 

 

Interference Considerations

3-13

 

 

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

iv

 

 

 

 

 

OL-13208-03

 

 

 

 

 

 

 

 

Contents

Rack-Mounting and Location Guidelines

3-14

Precautions for Rack-Mounting 3-14

Rack Selection Guidelines

3-15

 

Equipment Rack Guidelines

3-15

 

Site Planning Checklist

3-17

 

 

Preventing Electrostatic Discharge Damage

3-17

Electrical Safety 3-18

 

 

 

Receiving a Cisco ASR 1000 Series Router

3-19

Chassis-Lifting Guidelines

3-20

 

 

Tools and Equipment 3-21

 

 

 

 

 

Unpacking and Verifying Shipping Contents

3-21

 

 

 

 

 

 

Checking the Shipping Container Contents

3-21

 

 

 

 

 

 

 

Cisco ASR 1000 Series Router Installation Checklist

3-23

 

 

 

 

Cisco ASR 1006 Router Overview and Installation

 

 

 

 

C H A P T E R 4

4-1

 

 

 

 

 

Cisco ASR 1006 Router Description 4-1

 

 

 

 

 

 

 

 

 

Front View

4-2

 

 

 

 

 

 

 

 

 

 

 

Rear View

4-2

 

 

 

 

 

 

 

 

 

 

 

Installation Methods 4-4

 

 

 

 

 

 

 

 

 

 

 

General Rack Installation Guidelines

4-4

 

 

 

 

 

 

 

 

 

Guidelines for an Equipment Shelf or Tabletop Installation 4-5

 

 

Equipment Shelf or Tabletop Installation

4-6

 

 

 

 

 

 

 

 

Rack-Mounting a Cisco ASR 1006 Router

4-8

 

 

 

 

 

 

 

 

Verifying Rack Dimensions

4-8

 

 

 

 

 

 

 

 

 

 

Attaching the Chassis Rack-Mount Brackets

4-9

 

 

 

 

 

 

 

Chassis Front Rack-Mount Brackets

4-9

 

 

 

 

 

 

 

 

Chassis Rear Rack-Mount Brackets

4-10

 

 

 

 

 

 

 

 

Installing the Cisco ASR 1006 Router in a Rack

4-12

 

 

 

 

 

 

Two-Post Rack Installation

4-13

 

 

 

 

 

 

 

 

 

 

Four-Post Rack Installation

4-14

 

 

 

 

 

 

 

 

 

 

Attaching the Cable-Management Bracket

4-16

 

 

 

 

 

 

 

Attaching a Chassis Ground Connection

4-17

 

 

 

 

 

 

 

 

Recommended Tools and Supplies

4-19

 

 

 

 

 

 

 

 

Connecting Shared Port Adapter Cables

4-20

 

 

 

 

 

 

 

 

Connecting Console and Auxiliary Port Cables

4-20

 

 

 

 

 

 

Connecting the Ethernet Management Port Cable

4-21

 

 

 

 

 

Connecting Power to Cisco ASR 1006 Router

4-21

 

 

 

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

 

 

OL-13208-03

 

 

 

 

 

 

 

 

 

v

 

 

 

 

 

 

 

 

 

 

 

 

Contents

 

Connecting AC-Input Power to Cisco ASR 1006 Router

4-22

 

Connecting DC-Input Power to Cisco ASR 1006 Router

4-23

 

Connecting a Terminal to the Cisco ASR 1000 Series RP1 Console Port 4-27

 

Connecting System Cables 4-29

 

 

Auxiliary Connection 4-30

 

 

Cisco ASR 1004 Router Overview and Installation 5-1

 

C H A P T E R 5

 

 

Cisco ASR 1004 Router Description 5-1

 

 

Front View

5-2

 

 

Rear View

5-3

 

Installation Methods 5-5

 

 

 

General Rack Installation Guidelines 5-5

 

 

Guidelines for an Equipment Shelf or Tabletop Installation 5-6

Equipment Shelf or Tabletop Installation

5-7

 

Rack-Mounting a Cisco ASR 1004 Router

5-9

 

Verifying Rack Dimensions

5-9

 

 

Attaching the Chassis Rack-Mount Brackets

5-10

Chassis Front Rack-Mount Brackets

5-10

 

Chassis Rear Rack-Mount Brackets

5-11

 

Installing the Cisco ASR 1004 Router in a Rack

5-12

Two-Post Rack Installation

5-13

 

 

Four-Post Rack Installation

5-14

 

 

 

 

 

 

 

Attaching a Chassis Ground Connection

5-16

 

 

 

 

 

 

 

 

Recommended Tools and Supplies

5-17

 

 

 

 

 

 

 

 

Attaching the Cable-Management Bracket 5-19

 

 

 

 

 

 

 

Connecting Shared Port Adapter Cables

5-20

 

 

 

 

 

 

 

 

Connecting Console and Auxiliary Port Cables

5-21

 

 

 

 

 

 

 

Connecting the Ethernet Management Port Cable 5-21

 

 

 

 

 

 

 

Connecting Power to Cisco ASR 1004 Router

5-22

 

 

 

 

 

 

 

Connecting AC-Input Power to Cisco ASR 1004 Router

5-23

 

 

 

 

 

 

Connecting DC-Input Power to Cisco ASR 1004 Router

5-24

 

 

 

 

 

 

Connecting a Terminal to the Cisco ASR Series 1000 RP1 Console Port 5-29

 

 

 

 

 

Connecting Network Management and Signal System Cables

5-30

 

 

 

 

 

 

Auxiliary Connection 5-31

 

 

 

 

 

 

Cisco ASR 1002 Router Overview and Installation 6-1

 

 

C H A P T E R 6

 

 

 

 

 

 

 

 

Cisco ASR 1002 Router Description 6-1

 

 

 

 

 

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

vi

 

 

 

 

 

 

OL-13208-03

 

 

 

 

 

 

 

 

 

Contents

Front View

6-2

 

 

 

 

Rear View

6-3

 

 

 

 

Cisco ASR 1002 Router Components

6-4

 

 

Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router Description 6-4

Cisco Embedded ASR1000-SIP10 and SPAs for the Cisco ASR 1002 Router Description 6-4

Cisco ASR1000-ESP5 or ASR1000-ESP10 Description 6-5

Power Supplies in the Cisco ASR 1002 Router 6-6

 

AC Power Supply for Cisco ASR 1002 Router

6-6

DC Power Supply for Cisco ASR 1002 Router

6-7

Installation Methods 6-9

 

 

 

 

General Rack Installation Guidelines 6-10

 

 

Guidelines for an Equipment Shelf or Tabletop Installation 6-11

Equipment Shelf or Tabletop Installation

6-12

 

Rack-Mounting a Cisco ASR 1002 Router

6-13

 

Verifying Rack Dimensions

6-14

 

 

 

Attaching the Chassis Rack-Mount Brackets

6-15

 

Chassis Front Rack-Mount Brackets

6-15

 

 

Chassis Rear Rack-Mount Brackets

6-16

 

 

Installing the Cisco ASR 1002 Router in a Rack

6-17

 

Two-Post Rack Installation

6-18

 

 

 

Four-Post Rack Installation

6-19

 

 

 

Attaching the Cable-Management Bracket

6-21

 

Attaching a Chassis Ground Connection

6-23

 

 

Connecting Shared Port Adapter Cables

6-25

 

 

 

Connecting Console and Auxiliary Port Cables

6-26

 

 

Management Ethernet Port Cable Connection 6-27

 

 

Connecting Power to Cisco ASR 1002 Router

6-27

 

 

Connecting AC-Input Power to Cisco ASR 1002 Router

6-29

 

Connecting DC-Input Power to Cisco ASR 1002 Router

6-31

 

Connecting a Terminal to the Cisco ASR1000-RP1 Console Port 6-35

 

Connecting Cables

6-36

 

 

 

Auxiliary Connection

6-36

 

 

 

Cisco ASR 1000 Series Routers Power Up and Initial Configuration 7-1

C H A P T E R 7

 

Checking Conditions Prior to System Startup

7-1

 

 

Verifying Power Supply Operation 7-2

 

 

 

Powering Up the Cisco ASR 1000 Series Routers

7-3

 

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

OL-13208-03

 

 

vii

 

 

 

 

 

Contents

Verifying the Front Panel LEDs

7-7

Verifying the Hardware Configuration 7-7

Checking Hardware and Software Compatibility 7-7

Configuring the Cisco ASR 1000 Series Routers at Startup 7-7

Using the Console Interface

7-8

Configuring Global Parameters

7-8

 

Checking the Running Configuration Settings

7-9

 

Saving the Running Configuration to NVRAM

7-10

 

Power Off the Cisco ASR 1000 Series Router 7-10

 

 

Replacing Cisco ASR 1000 Series Routers Field-Replaceable Units 8-1

C H A P T E R 8

 

Removing and Replacing the Cisco ASR 1000 Series RP1 8-1

 

Removing the Cisco ASR1000-RP1

8-2

 

 

Replacing the Cisco ASR1000-RP1

8-2

 

 

 

 

Removing and Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive

8-3

 

 

 

 

 

Cisco ASR 1000 Series RP1 Spare Hard Drive Accessory Kit

8-3

 

 

 

 

 

 

Removing the Cisco ASR 1000 Series RP1 and Internal Hard Drive from the Cisco ASR 1000 Series

 

 

 

Router 8-4

 

 

 

 

 

 

 

 

 

Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive 8-8

 

 

 

 

 

 

Removing and Replacing the Cisco ASR 1000 Series RP1 DIMM Memory Module

8-9

 

 

 

 

Removing and Replacing an eUSB Device

8-13

 

 

 

 

 

 

 

 

Removing and Replacing the 1GB USB Flash Token Memory Stick

8-15

 

 

 

 

 

 

Removing and Replacing the Cisco ASR 1000 Series Embedded Service Processors

8-17

 

 

 

 

Removing a Cisco ASR1000-ESP 8-17

 

 

 

 

 

 

 

 

Replacing the Cisco ASR1000-ESP

8-18

 

 

 

 

 

 

 

 

Removing and Replacing a SPA Interface Processor

8-19

 

 

 

 

 

 

 

Electrostatic Discharge Prevention

8-19

 

 

 

 

 

 

 

 

Removing a SPA Interface Processor

8-21

 

 

 

 

 

 

 

 

Replacing a SPA Interface Processor

8-21

 

 

 

 

 

 

 

 

Removing a Shared Port Adapter From a SIP

8-21

 

 

 

 

 

 

 

Replacing a Shared Port Adapter In a SIP 8-22

 

 

 

 

 

 

 

Removing and Replacing a Cisco ASR 1006 Router Power Supply

8-22

 

 

 

 

 

 

Removing the AC Power Supply from Cisco ASR 1006 Router

8-23

 

 

 

 

 

 

Replacing the AC Power Supply in Cisco ASR 1006 Router

8-24

 

 

 

 

 

 

Removing and Replacing a DC Power Supply in Cisco ASR 1006 Router

8-25

 

 

 

 

 

Removing the DC Power Supply from Cisco ASR 1006 Router

8-26

 

 

 

 

 

 

Replacing the DC Power Supply in Cisco ASR 1006 Router

8-29

 

 

 

 

 

 

Removing and Replacing a Cisco ASR 1004 Router Power Supply

8-31

 

 

 

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

 

 

 

 

 

viii

 

 

 

 

 

 

OL-13208-03

 

 

 

 

 

 

 

 

 

Contents

 

Removing the AC Power Supply from Cisco ASR 1004 Router

8-31

 

 

Replacing the AC Power Supply in Cisco ASR 1004 Router

 

8-33

 

 

Removing and Replacing a DC Power Supply in Cisco ASR 1004 Router

8-33

 

Removing the DC Power Supply From Cisco ASR 1004 Router 8-35

 

 

Replacing the DC Power Supply in Cisco ASR 1004 Router

 

8-37

 

 

Removing and Replacing a Cisco ASR 1002 Router Power Supply

8-40

 

 

Removing the AC Power Supply from Cisco ASR 1002 Router

8-40

 

 

Replacing the AC Power Supply in Cisco ASR 1002 Router

 

8-41

 

 

Removing and Installing a DC Power Supply in Cisco ASR 1002 Router 8-43

 

Removing the DC Power Supply from Cisco ASR 1002 Router

8-45

 

 

Replacing the DC Power Supply in Cisco ASR 1002 Router

 

8-46

 

 

Repacking the Box 8-48

 

 

 

 

 

 

Cisco ASR 1000 Series Routers Specifications A-1

 

 

 

 

A P P E N D I X A

 

 

 

 

 

Cisco ASR 1006 Router Specifications

A-1

 

 

 

 

 

Cisco ASR 1006 Router Memory and Storage Options

A-2

 

 

 

 

Cisco ASR 1006 Router Ethernet RJ-45 Port Pinouts

A-2

 

 

 

 

Cisco ASR 1006 Router MGMT Ethernet Port Pinouts

A-2

 

 

 

 

Cisco ASR 1006 Router BITS Port Signals and Pinouts

A-3

 

 

 

 

Cisco ASR 1006 Router Console Port Signals and Pinouts

A-3

 

 

Cisco ASR 1006 Router Auxiliary Port Signals and Pinouts

 

A-4

 

 

Cisco ASR 1006 Router DB-25 Pinout Assignments for Alarm Relays

A-4

 

Cisco ASR 1004 Router Specifications

A-5

 

 

 

 

 

Cisco ASR 1004 Router Memory and Storage Options

A-5

 

 

 

 

Cisco ASR 1004 Router Ethernet RJ-45 Port Pinouts

A-5

 

 

 

 

Cisco ASR 1004 Router MGMT Ethernet Port Signals and Pinouts

A-6

 

Cisco ASR 1004 Router Console Port Signals and Pinouts

A-6

 

 

Cisco ASR 1004 Router Auxiliary Port Signals and Pinouts

 

A-7

 

 

Cisco ASR 1004 Router BITS Port Signals and Pinouts

A-7

 

 

 

 

Cisco ASR 1004 Router DB-25 Pinout Assignments for Alarm Relays

A-8

 

Cisco ASR 1002 Router Specifications

A-8

 

 

 

 

 

Cisco ASR 1002 Router Memory and Storage Options

A-9

 

 

 

 

Cisco ASR 1002 Router Ethernet RJ-45 Port Pinouts

A-9

 

 

 

 

Cisco ASR 1002 Router MGMT Ethernet Port Signals and Pinouts

A-10

 

Cisco ASR 1002 Router Console Port Signals and Pinouts

A-10

 

 

Cisco ASR 1002 Router Auxiliary Port Signals and Pinouts

 

A-11

 

 

Cisco ASR 1002 Router BITS Port Signals and Pinouts

A-11

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

ix

 

Contents

A P P E N D I X B

Troubleshooting Initial Startup Problems B-13

 

Troubleshooting Overview B-13

 

Online Troubleshooting Resources B-14

 

General Troubleshooting Tips B-14

Troubleshooting Using a Subsystem Approach

B-15

Normal Router Startup Sequence B-15

 

 

Troubleshooting the Power Subsystem

B-16

 

Troubleshooting the Cooling Subsystem

B-17

 

Troubleshooting the Shared Port Adapter

B-18

Troubleshooting the Upgrade B-19

 

 

Replacing or Recovering a Lost Password B-19

 

Overview of the Password Recovery Procedure

B-19

Details of the Password Recovery Procedure

B-20

G L O S S A R Y

I N D E X

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

x

OL-13208-03

 

 

 

Preface

This preface discusses the objectives, audience, and organization of the Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide. The following sections are in this preface:

Document Revision History, page xi

Document Objectives, page xii

Audience, page xii

Document Organization, page xii

Safety Warnings and Cautions, page xiii

Related Documentation, page xviii

Obtaining Documentation and Submitting a Service Request, page xix

Document Revision History

The Document Revision History table below records technical changes to this document.

Document

 

 

Version

Date

Change Summary

 

 

 

OL-13208-03

November 2008

Improved the two-minute window allotted time to

 

 

replace a power supply. You now have up to a maximum

 

 

of five minutes to replace the power supply.

 

 

 

OL-13208-02

October 2008

Added Cisco ASR1000-ESP20 and Cisco

 

 

ASR1000-ESP10-N support. Updated eUSB device

 

 

graphics and replacement information.

 

 

 

OL-13208-01

May 2008

This is the first version of this document for the Cisco

 

 

ASR 1000 Series Routers (Cisco ASR1006 Router, Cisco

 

 

ASR1004 Router, Cisco ASR1002 Router).

 

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

xi

 

Preface

Document Objectives

Document Objectives

This publication describes the installation of the Cisco ASR 1000 Series Aggregation Services Routers, replacement or upgrading of field-replaceable units (FRUs), and troubleshooting of the Cisco ASR 1000 Series Routers hardware. The purpose of this guide is to enable the safe and efficient installation of the Cisco ASR 1000 Series Aggregation Services Routers.

Audience

This publication is primarily designed for the person responsible for installing, maintaining, and troubleshooting the Cisco ASR 1000 Series Aggregation Services Routers. The users of this guide should:

Be familiar with electronic circuitry and wiring practices.

Have experience as electronic or electromechanical technicians.

Have experience in installing high-end networking equipment. Certain procedures described in this guide require a certified electrician.

Document Organization

The major sections of this installation and configuration guide are:

Chapter and Appendix Number and Title

Description

 

 

Preface

The preface provides objectives, audience and

 

organization of this manual.

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

This chapter provides an overview of the Cisco ASR

 

1000 Series Aggregation Services Routers.

 

 

Chapter 2 Cisco ASR 1000 Series Router Components

This chapter describes the components for each Cisco

 

ASR 1000 Series Aggregation Services Router.

 

 

Chapter 3 Preparing Your Site for Installation

This chapter provides site preparation guidelines for

 

installing the ASR 1000 Series Routers.

 

 

Chapter 4 Cisco ASR 1006 Router

This chapter describes the Cisco ASR 1006 router and

 

how to install it.

 

 

Chapter 5 Cisco ASR 1004 Router

This chapter describes the Cisco ASR 1004 router and

 

how to install it.

 

 

Chapter 6 Cisco ASR 1002 Router

This chapter describes the Cisco ASR 1002 router and

 

how to install it.

 

 

Chapter 7 Cisco ASR 1000 Series Router Power Up and Initial

This chapter provides basic system startup and initial

Configuration

configuration information.

 

 

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

xii

OL-13208-03

 

 

 

Preface

Safety Warnings and Cautions

Chapter and Appendix Number and Title

Description

 

 

Chapter 8 Replacing the Cisco ASR 1000 Series Routers

This chapter provides instructions for removing and

Field-Replaceable Units

replacing shared port adapters, ASR 1000 RP1 internal

 

hard drive, AC and DC power supplies, the Cisco

 

ASR1000-ESP forwarding processors, the Cisco DIMM

 

memory card, the Cisco memory stick, and the Cisco

 

ASR 1000 Series Route Processor 1.

 

 

Appendix A Cisco ASR 1000 Series Routers Specifications

This appendix provides system specifications and

 

pinouts.

 

 

Appendix B Troubleshooting Initial Startup Problems

This appendix provides basic system startup

 

troubleshooting information.

 

 

Glossary

Listing of Cisco ASR 1000 Series Routers terms with

definitions.

 

 

Index

Listing of terms for the Cisco ASR 1000 Series Routers

 

 

Safety Warnings and Cautions

Most safety warnings for the Cisco ASR 1000 Series Routers are placed in relevant sections throughout the document. For translated safety warnings, see the Regulatory Compliance and Safety Information for the Cisco 1000 Series Aggregation Services Routers. Below is Statement 1071, the Warning Definition statement, complete with translated warnings.

Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

xiii

 

Preface

Safety Warnings and Cautions

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

xiv

OL-13208-03

 

 

 

Preface

Safety Warnings and Cautions

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

xv

 

Preface

Safety Warnings and Cautions

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

xvi

OL-13208-03

 

 

 

Cisco Systems ASR 1000 User Manual

Preface

Safety Warnings and Cautions

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

xvii

 

Preface

Related Documentation

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Related Documentation

Your Cisco ASR1000 Series Routers and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources:

All documentation related to the Cisco ASR 1000 Series Routers is listed in the online Cisco ASR 1000 Series Aggregation Services Routers Documentation Roadmap. Information in this master index includes troubleshooting tools and documentation, regulatory compliance and safety information, and installation and replacement information. Also see the Cisco ASR 1000 Series Port Adapter Documentation Roadmap for specific shared port adapters supported on the Cisco ASR1000 Series routers and the Cisco ASR 1000 Series Routers Troubleshooting Roadmap.

Some of the Cisco ASR1000 Series Routers documentation that is listed on the Cisco ASR 1000 Series Aggregation Services Routers Documentation Roadmap includes:

The Cisco ASR 1006, ASR 1004, and ASR 1002 Routers Quick Start Guide contain installation and configuration information. It contains quick reference information about chassis or parts installation.

The Cisco ASR 1000 Series Aggregation Services Routers Troubleshooting document contains information to help you troubleshoot problems with the Cisco ASR1000 Series Routers.

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

xviii

OL-13208-03

 

 

 

Preface

Obtaining Documentation and Submitting a Service Request

The Regulatory Compliance and Safety Information for Cisco ASR 1000 Series Aggregation Services Routers document provides international agency compliance, safety, and statutory information for wide-area network (WAN) interfaces for the Cisco ASR 1000 Series Routers.

Cisco ASR 1000 Series shared port adapter documentation.

Cisco IOS software documentation contains Cisco IOS software configuration information and support. See the modular configuration and modular command reference publications in the set that corresponds to the software release installed on your Cisco hardware.

To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether modules within a system are compatible, but it does provide the minimum IOS requirements for individual hardware modules or components.

Note Access to this tool is limited to users with Cisco.com login accounts.

Cisco Documentation DVD (See the “Obtaining Documentation and Submitting a Service Request” section on page xix.)

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

xix

 

Preface

Obtaining Documentation and Submitting a Service Request

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide

 

xx

OL-13208-03

 

 

 

C H A P T E R 1

Cisco ASR 1000 Series Routers Hardware

Overview

The Cisco ASR 1000 Series Aggregation Services Routers are the next generation midrange router products. The system is based on Cisco QuantumFlow Processor technology using a family of Cisco-developed processors.

The Cisco ASR 1000 Series Routers target both enterprise and service provider applications but with higher performance and improved availability. The specific applications covered by

Cisco ASR 1000 Series Routers are:

Enterprise applications—Intended as the mid-size aggregation and gateway router typically residing in a regional or large branch office:

WAN aggregation at Cisco Enterprise core

Internet gateway

Branch or regional office aggregation

Remote access aggregation

Service provider applications—Intended as the low-end service provider edge and broadband aggregation device with similar throughput:

High-end customer premises equipment (CPE) for business-quality Internet access

Provider edge (PE) and high-end customer edge (CE) for Layer 2 VPN or Layer 3 VPN services

Broadband aggregation—PPPoE/PPPoA aggregation and Service Selection Gateway (SSG)

Low-end Ethernet aggregation

This chapter provides an overview of the Cisco ASR 1000 Series Routers and includes the following information:

Cisco ASR 1000 Series Routers, page 1-2

Cisco ASR 1000 Series Routers Configurations, page 1-32

Field-Replaceable Units, page 1-4

Functional Overview, page 1-4

Cisco Product Identification Standard, page 1-15

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

1-1

 

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Cisco ASR 1000 Series Routers

Cisco ASR 1000 Series Routers

The Cisco ASR 1000 Series Aggregation Services Router is Cisco next-generation, modular, highly services-integrated routing platform designed with the flexibility to support a wide range of packet forwarding, system bandwidths, performance, and scaling. The overall system architecture is common across the chassis.

The Cisco ASR 1000 Series consists of three different versions:

Cisco ASR 1006 Router Description, page 4-1

Cisco ASR 1004 Router Description, page 5-1

Cisco ASR 1002 Router Description, page 6-1

All three models use the powerful Cisco QuantumFlow Processor which provides performance and resiliency for network processors.

The Cisco ASR 1000 Series Routers deliver multiple services embedded in the Cisco QuantumFlow Processor. The services supported on the Cisco Packet QuantumFlow Processor include security services (for example, encryption and firewall), quality of service (QoS), Network Based Application Recognition (NBAR), broadband aggregation, and session border controller, among others.

Cisco ASR 1000 Series Routers Features

The Cisco ASR 1000 Series Aggregation Services Routers use different field replaceable units. The processors are the Cisco ASR 1000 Series Route Processor 1 (RP1), Cisco ASR 1000 Series Embedded Services Processor (Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, and Cisco ASR1000-ESP20), and the Cisco ASR 1000 SPA Interface Processor (SIP). The Cisco ASR 1000 ESP is based on Cisco QuantumFlow Processor technology.

The Cisco ASR 1000 Series Routers contains the following features:

Online insertion and removal (OIR) capability

Route processor and embedded services processor redundancy in the Cisco ASR 1000 Series Routers

Control processor for ASR 1000 Series SPA Interface Processor

Control processor for embedded services processors (Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, or Cisco ASR1000-ESP20)

10Gbps and 20Gbps interconnect between Cisco QuantumFlow Processor with redundant Cisco ASR 1000 Series ESP to mirror data for stateful features

Power supply redundancy

Environmental monitoring and reporting functions

Family of routers using common hardware and software architecture

Centralized forwarding design (all network traffic passes through one engine)

Front-to-back airflow—Allows you to mount the router from either front or back into 19-inch equipment rack

Supports half-height shared port adapters (HHSPAs) and full-height shared port adapters (FHSPAs)

Single midplane design (all connectors on one interface midplane)

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

1-2

OL-13208-03

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Cisco ASR 1000 Series Routers Configurations

One 10/100/1000-Mbps Ethernet Management port—To be used only as a management port; not to be used as an Ethernet interface port

Both 25-MHz and 50-MHz shared port adapter operation

High availability software architecture

The Cisco QuantumFlow Processor processing provides:

Architecture to address Cisco ASR 1000 Series Router performance, cost, power, and feature velocity

Next Generation forwarding and queuing subsystems for Cisco routers to provide data path acceleration.

The Cisco ASR 1000 Series Router processor system performs the following system management functions:

Sending and receiving routing protocol updates

Managing tables, caches, and buffers

Monitoring interface and environmental status

Providing Simple Network Management Protocol (SNMP) management through the console and Telnet interface

Accounting for and switching of data traffic

Booting and reloading images

Cisco ASR 1000 Series Routers Configurations

The Cisco ASR 1000 Series Routers consist of a number of packaging configurations. The chassis configurations are modular with separate field-replaceable units (FRUs) for the Cisco ASR 1000 Series Route Processor 1 (RP1), the Cisco ASR 1000 Series Embedded Services Processor (ESP5, ESP10, and ESP20), and the shared port adapters.

With the exception of the Cisco ASR 1002 Router, all FRUs (Cisco ASR 1000 Series Route Processor 1, Cisco ASR 1000 Series Embedded Services Processor, and SPAs) are designed to work in the different chassis models. (The Cisco ASR1000-ESP20 is not supported in the Cisco ASR 1002 Router.) The power supplies and fan modules are chassis specific. The SPAs are supported in all chassis configurations although there are SPA restrictions in the Cisco ASR 1002 Router.

Table 1-1 lists the Cisco ASR 1000 Series Routers orderable configurations.

 

 

Table 1-1

Cisco ASR 1000 Series Routers Configurations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Number of

 

 

 

 

 

 

 

 

 

 

 

 

I/O Card

Maximum SPAs

Redundant RP1

 

Redundant ESP

Redundant Power

 

 

Chassis

Slots

Supported

Option

 

Option

Supply Option

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco ASR

3

12 HH

Yes

 

Yes

1 + 1

 

 

 

 

1006

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco ASR

2

8 HH

No

 

No

1 + 1

 

 

 

 

1004

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco ASR

0

3 HH (1 built-in

No

 

No

1 + 1

 

 

 

 

1002

 

4x1GE)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

 

 

 

 

 

OL-13208-03

 

 

 

 

 

 

 

1-3

 

 

 

 

 

 

 

 

 

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Field-Replaceable Units

Field-Replaceable Units

The Cisco ASR 1000 Series routers are easy to service; many of their major components are field-replaceable units (FRUs). The following is a list of the Cisco ASR 1000 Series Routers FRUs:

Cisco ASR 1000 Series Route Processor 1 (RP1)

Cisco ASR 1000 Series Embedded Services Processors (Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, Cisco ASR1000-ESP20)

Shared port adapters

Cisco ASR 1000 Series SIP (shared port adapter interface processor)

Cisco ASR 1000 Series RP1 internal hard drive

Cisco ASR 1000 Series RP1 DIMM memory module (Note that the Cisco embedded ASR1000-RP1 on the Cisco ASR 1002 Router DIMM memory module is not field-replaceable.)

USB Flash Token Memory Stick

AC and DC power supplies

Bracket kit—Custom cable-management brackets mount to each rack-mount bracket to provide cable-management to both sides of the chassis (parallel with card orientation). These brackets are screw-mounted to the rack brackets to allow easy installation and removal. There is a rack-mount bracket for each chassis:

Cisco ASR 1006 cable-management brackets contain 5 independent cable-management U-features to provide cable dressing of each card module slot. For SIPs, these brackets work in tandem with SPA product feature cable-management to allow installation and removal of adjacent cards without the need to remove cables.

Cisco ASR 1004 cable-management brackets contain three independent cable-management U-features to provide cable dressing of each card module slot. For SIPs, these brackets work in tandem with SPA product feature cable-management to allow installation and removal of adjacent cards without the need to remove cables.

Cisco ASR 1002 cable-management brackets contains one independent cable-management U-features to provide cable dressing of each card module slot. These brackets work in tandem with SPA product feature cable-management to allow installation and removal of adjacent cards without the need to remove cables

Functional Overview

This section contains the following topics:

Chassis Slot and Logical Interface Numbering, page 1-5

MAC Address Information, page 1-8

Online Insertion and Removal, page 1-9

Environmental Monitoring and Reporting Functions, page 1-10

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

1-4

OL-13208-03

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

Chassis Slot and Logical Interface Numbering

The Cisco ASR 1000 Series Routers have a slot numbering system located on both sides of the card module location. The chassis slots are physically numbered from zero starting at the bottom of the chassis. This section describes the slot numbering for the Cisco ASR 1000 Series Routers:

Cisco ASR 1006 Router Slot Numbering, page 1-5

Cisco ASR 1004 Router Slot Numbering, page 1-7

Cisco ASR 1002 Router Slot Numbering, page 1-7

Cisco ASR 1000 Series SPA Interface Processor (SIP) subslots begin their numbering with “0” and have a horizontal orientation. The SIP subslot numbering is indicated by a small numeric label beside the subslot on the faceplate. Some commands allow you to display information about the SPA itself, such as show idprom module and show hw-module subslot. These commands require you to specify both the physical location of the SIP and SPA in the format, Slot/Subslot, where:

Slot—Specifies the chassis slot number in the Cisco ASR 1000 Series Routers where the SIP is installed.

Subslot—Specifies a subslot of the SIP where the SPA is installed.

Cisco ASR 1006 Router Slot Numbering

The Cisco ASR 1006 Router is designed with each slot numbered as shown in Figure 1-1.

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

1-5

 

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

Figure 1-1 Cisco ASR 1006 Router — Slot Numbering

7

2

6

1

5

0

4

F1

3

F0

2

R1

1

R0

C/A

A/L

0

C/A

A/L

0

C/A

A/L

0

C/A

A/L

0

C/A

A/L

0

C/A

A/L

0

PWRACTV

STAT STBY

ASR1000-ESP10

PWRACTV

STAT STBY

ASR1000-ESP10

 

 

CRIT

 

 

PWR

ACTV

MAJ

ACO

STAT

STBY

MIN

 

 

ASR1000-RP1

 

 

 

 

 

CRIT

 

 

PWR

ACTV

MAJ

 

O

 

 

 

 

 

 

 

C

STAT

STBY

MIN

A

280033

 

ASR1000-RP1

 

 

1

Slot RP0 with ASR 1000 Series RP1

5

ASR 1000 Series SIP slot 0

 

 

 

 

2

Slot RP1 with ASR 1000 Series RP1

6

ASR 1000 Series SIP slot 1

 

 

 

 

3

Slot FP0 with ASR 1000 Series ESP

7

ASR 1000 Series SIP slot 2

 

 

 

 

4

Slot FP1 with ASR 1000 Series ESP

 

 

 

 

 

 

The Cisco ASR 1006 Router contains three Cisco ASR 1000 Series SPA Interface (SIP) supports four subslots for the installation of SPAs.

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

1-6

OL-13208-03

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

Figure 1-2 shows the Cisco ASR 1006 Router SPA subslot location.

Figure 1-2 Cisco ASR 1006 Router — ASR1000-SIP10 Subslots

Front of SIP, horizontal chassis slots

 

 

 

 

 

 

SPA 0

 

SPA 1

 

 

 

 

 

 

 

 

 

 

 

SPA 2

 

SPA 3

 

 

 

 

 

 

 

 

 

 

 

231508

Cisco ASR 1004 Router Slot Numbering

The Cisco ASR 1004 Router contains two Cisco ASR 1000 Series SPA Interface Processors (SIPs) and supports four subslots for the installation of SPAs.

Figure 1-3 shows the Cisco ASR 1004 Router with modules and filler plates installed.

Figure 1-3 Cisco ASR 1004 Router —Front and Side View

4

3

2

1

6 7

5 8

 

SPA-4XOC3-POS

 

3

 

2

 

1

 

0

 

SPA-4XOC3-POS

 

3

SPA-4XOC3-POS

2

3

1

2

0

1

 

0

SPA-4XOC3-POS

SPA-4XOC3-POS

3

3

2

2

1

1

0

0

 

SPA-4XOC3-POS

 

3

SPA-4XOC3-POS

2

3

1

2

0

1

 

0

 

SPA-4XOC3-POS

 

3

 

2

 

1

 

0

 

 

 

 

 

 

 

 

LINK

 

AUX

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

CON

 

 

 

 

 

 

HD

CARRIER

MGMT ETHERNE

 

 

 

 

 

 

 

USB

BITS

 

 

 

 

CRIT

 

 

 

DF

 

 

280312

 

ACTV

MAJ

 

O

 

 

 

PWR

AC

1

DISK

 

 

 

STBY

MIN

0

 

 

 

STAT

 

 

 

 

 

 

ASR1000-RP1

 

 

 

 

 

 

 

 

1

Slot RP0 with ASR 1000 Series RP1

5

SPA subslot 2

 

 

 

 

2

Slot FP0 with ASR 1000 Series ESP10

6

SPA subslot 0

 

 

 

 

3

ASR 1000 Series SIP slot 0

7

SPA subslot 1

 

 

 

 

4

ASR 1000 Series SIP slot 1

8

SPA subslot 3

 

 

 

 

Cisco ASR 1002 Router Slot Numbering

The Cisco ASR 1002 Router contains one Cisco embedded ASR1002 -RP1 which is addressed as R0 and one Cisco ASR1000-ESP5 or ASR1000-ESP10 forwarding processor in slot F0. The Cisco ASR 1002 Router consists of an embedded ASR1000-RP1 and embedded ASR1000-SIP10 board supporting three half-height SPAs or 1half-height and one full-height SPA and one Cisco ASR1000-ESP5 forwarding processor.

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

1-7

 

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

The SPA bays are bay 1, bay 2, and bay 3. The built-in 4xGE SPA ports are located in the SPA 0 location and will be addressed as GE 0/0/x. The Cisco ASR 1002 Router provides a built-in 4-Gigabit Ethernet interface and this SPA is physically located on the Cisco embedded ASR1000-RP1 board. The Cisco ASR 1000 Series ESP card is located in slot 1 and labeled as FP0.

Figure 1-4 Cisco ASR 1002 Router Slot Numbering

1

3

PWRACTV

STATSTBY

ASR1000-ESP10

ASR 1002

STAT

QE0

QE1

QE2

QE3

BOOT

CARRIER

LINK

pwr min

stat maj

crit

C/A

C/A

C/A

C/A

 

 

 

S

A/L

A/L

A/L

L

 

AT

U

 

A/

ST

 

 

0

1

2

3

SPA-4XOC3-POS

 

 

 

2

PWR

STAT

 

 

 

 

 

 

 

 

A

/A

A

/A

 

 

 

 

 

C/

C

C/

C

 

 

US

 

 

A/L

A/L

A/L

A/L

 

AT

 

 

ST

 

 

 

 

 

 

 

 

 

 

 

0

1

2

3

SPA-4XOC3-POS

 

 

280369

 

A

/A

/A

/A

 

 

 

 

C/

C

C

C

 

 

US

 

 

A/L

A/L

A/L

A/L

 

AT

 

 

ST

 

 

 

 

 

 

 

 

 

 

 

0

1

2

3

SPA-4XOC3-POS

 

 

 

4

1

Embedded route processor RP0 in subslot 0

3

Cisco SPA subslot 1

 

 

 

 

2

Cisco SPA subslot 2

4

Cisco SPA subslot 3

 

 

 

 

MAC Address Information

The Media Access Control (MAC) or hardware address is a standardized data link layer address that is required for certain network interface types. These addresses are specific and unique to each port and are not used by other devices in the network. The Cisco ASR 1000 Series Routers assign and control the MAC addresses of its shared port adapters.

You can identify shared port adapter slots by using software commands. To display information about:

All shared port adapter slots, use the show interfaces command.

A specific shared port adapter slot, use the show interfaces command with the shared port adapter type and slot number in the format show interfaces port-adapter-type slot-number/port-number.

Note If you abbreviate the command (sh int) and do not specify shared port adapter type and slot number (or arguments), the system interprets the command as show interfaces and displays the status of all shared port adapters and ports.

The MAC addresses are assigned to the slots in sequence. For example, in the Cisco ASR 1006 Router, the first address is assigned to slot 0 and the last address is assigned to slot 6. The actual MAC address assignment is 16 MAC addresses per SPA slot for half-height SPAs and 64 per SPA slot for full-height SPAs. Also, the Cisco ASR 1000 Series RP1 RP Management Ethernet port is assigned one MAC address from the end of the pool and for a Cisco ASR 1006 Router with two Cisco ASR 1000 RP1s, each ASR10000 RP1 is assigned one MAC address.

Using this address scheme, you can remove shared port adapters and insert them into other routers without causing the MAC addresses to move around the network or be assigned to multiple devices.

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

1-8

OL-13208-03

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

If the MAC addresses were stored on each shared port adapter, online insertion and removal would not function because you could never replace one shared port adapter with an identical one; the MAC addresses would always be different. Also, each time a shared port adapter was replaced, other devices on the network would have to update their data structures with the new address. If the other devices did not update quickly enough, the same MAC address could appear in more than one device at the same time.

Note Storing the MAC addresses for every slot in one central location means the addresses stay with the memory device on which they are stored.

Online Insertion and Removal

In the modular chassis configurations, most Cisco ASR 1000 Series Router field-replaceable units (FRUs) support online insertion and removal (OIR). However, the removal of critical non-redundant FRUs will result in service interruption.

Note As you disengage the shared port adapter from the router, online insertion and removal (OIR) administratively shuts down all active interfaces in the shared port adapter.

Online insertion and removal (OIR) allows you to install and replace shared port adapters while the router is operating; you do not need to notify the software or shut down the system power, although you should not run traffic through the shared port adapter you are removing while it is being removed. Online insertion and removal is a method that is seamless to end users on the network, maintains all routing information, and preserves sessions.

All SPA OIR events are independent of one another. An OIR event of a single SPA does not affect the other SPAs in that ASR1000-SIP10 or any other system function.

Note The Cisco ASR 1002 Router differs from the Cisco ASR 1006 and Cisco ASR 1004 routers. The Cisco ASR 1002 Router supports the Cisco embedded ASR1000-RP1 which is a combined route processor and carrier card which are not field-replaceable units. The Cisco ASR1000-ESP5 or ASR1000-ESP10 are field-replaceable units.

The following is a functional description of OIR for background information only; for specific procedures for installing and replacing a shared port adapter in Cisco ASR 1000 Series Routers, refer to the online configuration note for each shared port adapter.

When you remove or insert a shared port adapter in a Cisco ASR 1000 Series Router, the Control Processor notifies the Cisco ASR1000-RP1, which in turn notifies the forwarding engine control processor (FECP), and then performs as follows:

Rapidly scans the midplane for configuration changes.

Initializes all newly inserted shared port adapters, noting any removed interfaces and placing them in the administratively shutdown state.

Brings all previously configured interfaces on the shared port adapter back to the state they were in when they were removed. Any newly inserted interfaces are put in the administratively shutdown state, as if they were present (but not configured) at boot time. If a similar shared port adapter type is reinserted into a slot, its ports are configured and brought online up to the port count of the original SPA.

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

 

OL-13208-03

1-9

 

 

 

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview

Functional Overview

Environmental Monitoring and Reporting Functions

Environmental monitoring and reporting functions allow you to maintain normal system operation by identifying and resolving adverse conditions prior to loss of operation.

Caution To prevent overheating the chassis, ensure that your system is drawing cool inlet air. Over temperature conditions can occur if the system is drawing in the exhaust air of other equipment. Ensure adequate clearance around the sides of the chassis so that cooling air can flow through the chassis interior unimpeded and exhaust air exits the chassis and is not drawn into the inlet vent of another device.

Environmental Monitoring

The environmental monitoring functions use sensors to monitor the temperature of the cooling air as it moves through the chassis.

The local power supplies provide the ability to monitor:

Input and output voltage

Output current

Outlet temperature

The router is expected to meet the following environmental operating conditions:

Operating Temperature Nominal: 5° to 40°C

Operating Temperature Short Term: 5° to 55°C

Operating Humidity Nominal: 5% to 85% non-condensing

Operating Humidity Short Term: 5% to 90% non-condensing

Operating Altitude: 198 to 13,200 feet (60 to 4000 meters)

DC Input Range: –40.5 to –72 VDC

AC Input Range: 85 to 264 VAC

If the air temperature exceeds a defined threshold, the system controller displays warning messages on the console terminal, and if the temperature exceeds the shutdown threshold, the system controller shuts down the system.

In addition, the power supplies monitor internal power supply temperatures and voltages. A power supply is either within tolerance (normal) or out of tolerance (critical). If an internal power supply temperature or voltage reaches a critical level, the power supply shuts down without any interaction with the system processor.

The environmental monitoring functions use the following levels of status conditions to monitor the system:

Normal—All monitored parameters are within normal tolerances.

Warning—The system has exceeded a specified threshold. The system continues to operate, but operator action is recommended to bring the system back to a normal state.

Critical—An out-of-tolerance temperature or voltage condition exists. The system continues to operate; however, the system is approaching shutdown. Immediate operator action is required.

 

Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide

1-10

OL-13208-03

Loading...
+ 262 hidden pages