Cisco Systems 5505BUNK9, ASA5505K8RF, ASA5505BUNK9, ASA 5505 User Manual

0 (0)

Cisco ASA 5505 Adaptive Security

Appliance Hardware Installation Guide

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 527-0883

Customer Order Number: OL-18362-01

Text Part Number: OL-18362-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

©2007 Cisco Systems, Inc. All rights reserved.

C O N T E N T S

 

About This Guide

v

 

 

 

 

Document Objectives

v

 

 

 

Audience v

 

 

 

 

 

Document Organization

v

 

 

 

Document Conventions

vi

 

 

 

Installation Warnings

vi

 

 

 

Where to Find Safety and Warning Information x

 

Obtaining Documentation and Submitting a Service Request 1-x

 

Overview 1-1

 

 

 

 

C H A P T E R 1

 

 

 

 

 

Product Overview

1-1

 

 

 

 

Memory Requirements

1-3

 

 

 

Memory Requirements for the Software Version 8.3 and Later 1-3

 

Preparing for Installation

 

 

C H A P T E R 2

2-1

 

 

Installation Overview

2-1

 

 

 

Safety Recommendations

2-1

 

 

Maintaining Safety with Electricity 2-2

 

Preventing Electrostatic Discharge Damage 2-3

 

General Site Requirements

2-3

 

 

Site Environment

2-3

 

 

 

Preventive Site Configuration

2-3

 

Power Supply Considerations

2-4

 

Configuring Equipment Racks

2-4

 

Installing the Cisco ASA 5505

 

 

C H A P T E R 3

3-1

 

 

Installing the Chassis

3-1

 

 

 

Connecting the Interface Cables

3-1

 

Powering on the Cisco ASA 5505

3-3

 

Installing a Cable Lock

3-4

 

 

 

Rack or Wall Mounting the Cisco ASA 5505

3-4

 

 

 

 

Mounting the Chassis 3-5

 

 

 

 

 

Wall-Mounting the Chassis 3-5

 

 

 

 

 

 

Cisco ASA 5505 Hardware Installation Guide

 

 

 

 

 

 

 

OL-18362-01

 

 

iii

 

 

 

 

 

Contents

 

Rack-Mounting the Chassis

3-7

 

Installing and Wall-Mounting the Cisco ASA 5505 FIPS Enclosure 3-11

 

Maintenance and Upgrade Procedures

 

C H A P T E R 4

4-1

 

Removing and Replacing the Chassis Cover 4-1

 

Working in an ESD Environment

4-1

 

Removing the Chassis Cover

4-2

 

 

Replacing the Chassis Cover

4-3

 

 

Replacing the Lithium Battery

4-3

 

 

Installing and Replacing the SSC

4-4

 

 

Installing an SSC

4-5

 

 

 

 

Replacing an SSC

4-6

 

 

 

 

Upgrading Memory

4-6

 

 

 

 

Removing the DIMM

 

4-7

 

 

Installing the DIMM

4-8

 

 

Verifying the Memory Upgrade

4-9

 

Cable Pinouts

 

 

 

 

 

A P P E N D I X 1

1-1

 

 

 

 

 

10/100/1000BaseT Connectors

 

1-1

 

 

Console Port (RJ-45)

1-2

 

 

 

 

RJ-45 to DB-9

1-4

 

 

 

 

 

MGMT 10/100/1000 Ethernet Port 1-4

 

Gigabit and Fibre Channel Ports

 

1-5

 

I N D E X

Cisco ASA 5505 Hardware Installation Guide

 

iv

OL-18362-01

 

 

 

About This Guide

This preface includes the following sections:

Document Objectives, page v

Audience, page v

Document Organization, page v

Document Conventions, page vi

Installation Warnings, page vi

Obtaining Documentation and Submitting a Service Request, page x

Document Objectives

This guide describes how to perform installation and maintenance procedures on the Cisco ASA 5505 Adaptive Security Appliance.

Audience

This guide is for network administrators who perform any of the following tasks:

Managing network security

Installing and configuring firewalls

Managing default and static routes, and TCP and UDP services

Document Organization

This guide includes the following chapters and appendices:

Chapter 1, “Overview,” describes the product overview, LEDs and memory requirements.

Chapter 2, “Preparing for Installation,” describes the installation overview, safety recommendations, and general site requirements.

Chapter 3, “Installing the Cisco ASA 5505,” describes how to connect the interface cables, and rack or wall mount the chassis .

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

v

 

About This Guide

Chapter 4, “Maintenance and Upgrade Procedures,” describes the adaptive security appliance maintenance and upgrade procedures.

Appendix 1, “Cable Pinouts,” describes the cable pinouts.

Document Conventions

Command descriptions use these conventions:

Braces ({ }) indicate a required choice.

Square brackets ([ ]) indicate optional elements.

Vertical bars (|) separate alternative, mutually exclusive elements.

Boldface indicates commands and keywords that are entered literally as shown.

Italics indicate arguments for which you supply values.

Examples use these conventions:

Examples depict screen displays and the command line in screen font.

Information you need to enter in examples is shown in boldface screen font.

Variables for which you must supply a value are shown in italic screen font. Graphical user interface examples uses these conventions:

Boldface indicates buttons and menu items.

Selecting a menu item (or pane) is indicated by the following convention: Choose Start > Settings > Control Panel.

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.

Installation Warnings

Be sure to read the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series document that accompanied this device before installing the chassis. This document contains important safety information. This section includes the following warnings:

Power Supply Disconnection Warning, page vii

Jewelry Removal Warning, page vii

Wrist Strap Warning, page vii

Work During Lightning Activity Warning, page vii

Installation Instructions Warning, page vii

Chassis Warning for Rack-Mounting and Servicing, page viii

Short-Circuit Protection Warning, page viii

SELV Circuit Warning, page viii

Ground Conductor Warning, page viii

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

vi

OL-18362-01

 

 

 

About This Guide

Blank Faceplates and Cover Panels Warning, page viii

Product Disposal Warning, page viii

Short-Circuit Protection Warning, page ix

Compliance with Local and National Electrical Codes Warning, page ix

DC Power Connection Warning, page ix

AC Power Disconnection Warning, page ix

TN Power Warning, page ix

48 VDC Power System, page ix

Multiple Power Cord, page ix

Circuit Breaker (15A) Warning, page ix

Grounded Equipment Warning, page x

Safety Cover Requirement, page x

Faceplates and Cover Panel Requirement, page x

Power Supply Disconnection Warning

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units. Statement 12

Jewelry Removal Warning

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Wrist Strap Warning

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Work During Lightning Activity Warning

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Installation Instructions Warning

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

vii

 

About This Guide

Chassis Warning for Rack-Mounting and Servicing

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack.When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006

Short-Circuit Protection Warning

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

SELV Circuit Warning

Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021

Ground Conductor Warning

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Blank Faceplates and Cover Panels Warning

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Product Disposal Warning

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

viii

OL-18362-01

 

 

 

About This Guide

Short-Circuit Protection Warning

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Compliance with Local and National Electrical Codes Warning

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

DC Power Connection Warning

Warning After wiring the DC power supply, remove the tape from the circuit breaker switch handle and reinstate power by moving the handle of the circuit breaker to the ON position. Statement 8

AC Power Disconnection Warning

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units.

Statement 246

TN Power Warning

Warning The device is designed to work with TN power systems. Statement 19

48 VDC Power System

Warning The customer 48 volt power system must provide reinforced insulation between the primary AC power and the 48 VDC output. Statement 128

Multiple Power Cord

Warning This unit has more than one power cord. To reduce the risk of electric shock when servicing a unit, disconnect the power cord of the power strip that the unit is plugged into. Statement 137

Circuit Breaker (15A) Warning

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors). Statement 13

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

ix

 

About This Guide

Obtaining Documentation and Submitting a Service Request

Grounded Equipment Warning

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Safety Cover Requirement

Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117

Faceplates and Cover Panel Requirement

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 142

Where to Find Safety and Warning Information

For safety and warning information, see the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series document that accompanied the product. This document describes the international agency compliance and safety information for the Cisco ASA 5505 Adaptive Security Appliance. It also includes translations of the safety warnings.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

x

OL-18362-01

 

 

 

C H A P T E R 1

Overview

Read through the entire guide before beginning any of the procedures in this book.

Warning Only trained and qualified personnel should install, replace, or service this equipment. Statement 49

Caution Read the safety warnings in the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series and follow proper safety procedures when performing these steps.

This chapter describes the product and the memory requirements and includes the following topics:

Product Overview, page 1-1

Memory Requirements, page 1-3

Product Overview

The Cisco ASA 5505 Adaptive Security Appliance delivers unprecedented levels of defense against threats to the network with deeper web inspection and flow-specific analysis, improved secure connectivity via end-point security posture validation, and voice and video over VPN support. It also provides enhanced support for intelligent information networks through improved network integration, resiliency, and scalability.

The adaptive security appliance software combines firewall, VPN concentrator, and intrusion prevention software functionality into one software image. Previously, these functions were available in three separate devices, each with its own software and hardware. Combining the functionality into just one software image provides significant improvements in the available features.

Additionally, the adaptive security appliance software supports Adaptive Security Device Manager (ASDM). ASDM is a browser-based, Java applet used to configure and monitor the software on the adaptive security appliances. ASDM is loaded from the adaptive adaptive security appliance, then used to configure, monitor, and manage the device.

This section describes the front and rear panels. Figure 1-1 shows the front panel LEDs.

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

1-1

 

 

 

Cisco Systems 5505BUNK9, ASA5505K8RF, ASA5505BUNK9, ASA 5505 User Manual

Chapter 1 Overview

Product Overview

Figure 1-1 Front Panel LEDs and Ports

3

4 5 6 7 8

LINK/ACT

Power

Status Active

VPN

SSC

 

100 MBPS

 

 

 

 

 

 

 

0

1

2

3

4

5

6

7

0

 

 

 

 

 

 

Cisco ASA 5505 Series

 

 

 

 

 

 

Adaptive Security Appliance

 

 

 

 

 

 

 

1

2

153644

1

USB 2.0 interface

5

Status

 

 

 

 

2

100 Mbps

6

Active

 

 

 

 

3

LINK/ACT LEDs

7

VPN

 

 

 

 

4

Power

8

SSC

 

 

 

 

Figure 1-2 shows the rear panel LEDs and Ports.

Figure 1-2 Rear Panel LEDs and Ports (AC Power Supply Model Shown)

2

3

5

 

 

 

 

Security

 

Console

 

 

 

 

Services

 

 

 

 

 

Card Slot

 

 

POWER

 

 

 

 

 

1

48VDC

 

 

 

 

 

RESET

 

 

 

 

 

 

 

 

 

 

 

 

2

7 POWER over ETHERNET 6

5

4

3

2

1

0

8

153645

 

1

4

 

6

7

 

 

 

 

 

 

1

Power 48VDC

 

5

Console port

 

 

 

 

 

 

 

2

SSC slot

 

6

USB 2.0 interface

 

 

 

 

 

 

 

3

Network interface LEDs

 

7

Reset button

 

 

 

 

 

 

 

4

Network interfaces1

 

8

Lock slot

 

1.Ports 6 and 7 are 15-Watt output PoE ports, used for devices, such as IP phones, which can be powered by the network interface. They can also be used as regular Ethernet switch ports, just like the ports numbered 0 through 5.

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

1-2

OL-18362-01

 

 

Chapter 1 Overview

Memory Requirements

Memory Requirements

The default DRAM memory is 256MB and the default internal flash memory is 128MB for the Cisco ASA 5505.

In a failover configuration, the two units must have the same hardware configuration They must be the same model, have the same number and types of interfaces, and the same amount of RAM.

Note The two units do not have to have the same size Flash memory. If using units with different Flash memory sizes in your failover configuration, make sure the unit with the smaller Flash memory has enough space to accommodate the software image files and the configuration files. If it does not, configuration synchronization from the unit with the larger Flash memory to the unit with the smaller Flash memory will fail.

For more information, see the Cisco Security Appliance Command Line Configuration Guide.

Memory Requirements for the Software Version 8.3 and Later

For information on memory requirements for the adaptive security appliance for software Version 8.3 or later, go to: http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/product_bulletin_c25-58 6414.html

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

1-3

 

 

 

Chapter 1 Overview

Memory Requirements

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

1-4

OL-18362-01

 

 

C H A P T E R 2

Preparing for Installation

The information in this guide applies to the Cisco ASA 5505 In this guide, references to “adaptive security appliance” or security appliance apply to the Cisco ASA 5505 chassis unless specifically noted otherwise.

This chapter describes the steps to follow before installing new hardware or performing hardware upgrades, and includes the following sections:

Installation Overview, page 2-1

Safety Recommendations, page 2-1

General Site Requirements, page 2-3

Installation Overview

To prepare for the installation of the chassis, perform the following steps:

Step 1 Review the safety precautions outlined in the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series document.

Step 2 Read the release notes for the respective software version.

Step 3 Unpack the chassis. An accessory kit ships with the chassis and includes the following items: documentation, a product CD, a power cord (AC models only), two RJ-45 Ethernet cables, one RJ-45 to DB-9 console cable, a rack-mounting kit, and four self-adhesive feet (for desktop mounting).

Step 4 Place the chassis on a stable work surface.

Safety Recommendations

Use the following guidelines and the information in the following sections to help ensure your safety and protect the adaptive security appliance. The list of guidelines may not address all potentially hazardous situations in your working environment, so be alert and exercise good judgement at all times.

Note If you need to remove the chassis cover to install a hardware component, such as additional memory or an interface card, doing so does not affect your Cisco warranty. Upgrading the adaptive security appliance does not require any special tools and does not create any radio frequency leaks.

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

 

OL-18362-01

2-1

 

 

 

Chapter 2 Preparing for Installation

Safety Recommendations

The safety guidelines are as follows:

Keep the chassis area clear and dust-free before, during and after installation.

Keep tools away from walk areas where you and others could fall over them.

Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains, that could get caught in the chassis.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe. This section includes the following topics:

Maintaining Safety with Electricity, page 2-2

Preventing Electrostatic Discharge Damage, page 2-3

Maintaining Safety with Electricity

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units. Statement 12

Follow these guidelines when working on equipment powered by electricity:

Before beginning procedures that require access to the interior of the chassis, locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn off the power.

Do not work alone if potentially hazardous conditions exist anywhere in your work space.

Never assume that power is disconnected from a circuit; always check the circuit.

Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, frayed power cords, and missing safety grounds.

If an electrical accident occurs, proceed as follows:

Use caution; do not become a victim yourself.

Disconnect power from the system.

If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help.

Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.

Use the adaptive security appliance chassis within its marked electrical ratings and product usage instructions.

Install the adaptive security appliance in compliance with local and national electrical codes as listed in the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series document.

The adaptive security appliance models equipped with AC-input power supplies are shipped with a 3-wire electrical cord with a grounding-type plug that fits only a grounding-type power outlet. Do not circumvent this safety feature. Equipment grounding should comply with local and national electrical codes.

Cisco ASA 5505 Adaptive Security Appliance Hardware Installation Guide

2-2

OL-18362-01

 

 

Loading...
+ 36 hidden pages